- 10 Oct, 2007 40 commits
-
-
Mike Isely authored
Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Simon Farnsworth authored
Fix SVideo input on KWorld DVB-T 220 boards. Without this patch, the luma pin on the SVideo input is treated as a composite in, and the chroma pin is ignored. Also, fix the radio, and provide a second composite input for people who are used to the existing composite on SVideo connector behaviour. Signed-off-by:
Simon Farnsworth <simon.farnsworth@onelan.co.uk> Reviewed-by:
Hermann Pitton <hermann-pitton@arcor.de> Signed-off-by:
-
Michael Krufky authored
Store a pointer to the required i2c_bus so that we do not put the wrong analog demod into standby. Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
Steven Toth <stoth@hauppauge.com> Signed-off-by:
-
Steven Toth authored
cx23885: Changes to allow demodulators on each transport bus. Signed-off-by:
-
Michael Krufky authored
Cardlist generated by cx23885.pl Signed-off-by:
-
Michael Krufky authored
This patch adds digital ATSC / QAM support for the DViCO FusionHDTV5 Express. Remote control is supported by ir-kbd-i2c, RTC is supported by rtc-isl1208. Signed-off-by:
-
Steven Toth authored
Changes to support MPEG TS on VIDB Signed-off-by:
-
Steven Toth authored
Changes to support interrupts on VIDB Signed-off-by:
-
Michael Krufky authored
- define missing register bit values for VID_B - corrected VID/VBI_B_GPCNT_CTL register addresses Signed-off-by:
-
Steven Toth authored
start_dma() would fail to start dma if a device used VIDB (portb). Signed-off-by:
-
Steven Toth authored
The switch() statement is no longer required. Signed-off-by:
-
Steven Toth authored
The HVR1250 and HVR1800 boards need the s5h1409 demod GPIO enabled. Signed-off-by:
-
Trent Piepho authored
Not sure why they are there, but they don't do anything now. Signed-off-by:
Trent Piepho <xyzzy@speakeasy.org> Signed-off-by:
-
Trent Piepho authored
Use the balance control to make the mono volume control stereo. Note that full range isn't supported. The balance control attenuates one channel by 0 to -63 dB, and the volume control provides additional attenuation to both channels by another 0 to -63 dB. So the channel with the most attenuation has a range of 0 to -126 dB, while the other channel only has a range of 0 to -63 dB. ALSA volume controls don't appear to support this concept. I just limited the range to 0 to -63 total. Once you get to -63 dB, you're already at silence, so additional attenuation is pretty much pointless anyway. Signed-off-by:
-
Michael Krufky authored
Auto-load ir-kbd-i2c for ir receiver support, and rtc-isl1208 for rtc support for the FusionHDTV5 RT Gold. Signed-off-by:
-
Michael Krufky authored
Ignore 0x6b and 0x6f on cx88 boards. Some FusionHDTV cards have an ir receiver at 0x6b and an RTC at 0x6f which can get corrupted if probed. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Michael Krufky authored
- fixed missing buttons in keymap. - make function names & descriptions more generic, since this same ir receiver and remote is used in many FusionHDTV products. - miscellaneous cleanups. Signed-off-by:
-
Chaogui Zhang authored
This patch adds support for the built-in IR receiver of the DViCO Fusion HDTV5 RT GOLD PCI card, using FusionHDTV MCE remote controller. Signed-off-by:
Chaogui Zhang <czhang1974@gmail.com> Signed-off-by:
-
Steven Toth authored
I wanted to document the NMI assert issue inside the code, even though it's already documented in the patch history. If/when the next cx23887 revision appears, is may need to be enabled on that also. Signed-off-by:
-
Steven Toth authored
A number of Hauppauge boards share the same tuner and demod configurations. This patch removes duplicate structures. Signed-off-by:
-
Steven Toth authored
Moving some defines into the correct header file. Signed-off-by:
-
Steven Toth authored
Removed unused code. Signed-off-by:
-
Steven Toth authored
Unused code is removed. Signed-off-by:
-
Steven Toth authored
Adding support for the Hauppauge HVR1250 PCIe ATSC board. Signed-off-by:
-
Steven Toth authored
Changed the pci_quirks function to detech the bridge type before setting the NMI clear bit, rather than detecting based on unique board id. Signed-off-by:
-
Steven Toth authored
The pci_quirks function was being called too early during initialisation, it needs to be called after the board has been identified. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Turn off i2c_debug by default, to make the driver less verbose. Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
The dvb-pll module is not being used by this driver. Remove the unneeded #include. Signed-off-by:
-
Steven Toth authored
Removed if 0'd code, removed cx88 references. Signed-off-by:
-
Steven Toth authored
The mt2131 tuner reports lock even when the hardware should not lock. This patch allows the s5h1409 demodulator to be configured to query either the tuner driver for status, or the demodulator status when the application requests lock status. This avoids returning false CARRIER and/or SIGNAL lock status. S5H1409 and MT2131 drivers. This is the remainder of the changeset, which only touches cx23885-dvb.c Signed-off-by:
-
Steven Toth authored
Moved the field from cx23885_board to cx23885_dev and added code to iautomatically set the bridge type based on the pci device id. Signed-off-by:
-
Steven Toth authored
This is required to support the cx258xx family of audio and video decoders. Signed-off-by:
-
Steven Toth authored
The cx23885 and cx23887 family use two different memory maps which govern how the internal SRAM is configured. This patch streamlines the access to those structures. Signed-off-by:
-
Steven Toth authored
The sram allocations for the cx23887 differ slightly from the cx23885. This patch modifies the cx23887 specific sram memory map to reflect this. As a result, interrupts and DMA handling have also been enabled in cx23885_start_dma() for 887 specific boards. ATSC streaming is now available on cx23885 and cx23887 bridges. Signed-off-by:
-
Steven Toth authored
I2C bus 3 was being initialised with the incorrect address register. Signed-off-by:
-
Michael Krufky authored
- fix #include for <media/video-buf-dvb.h> - fix cx23885_irq declaration for 2.6.19 and later Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
