Petr Machata says:

====================
selftest: Clean-up and stabilize mirroring tests

The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.

The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.
As a result, the selftests are noisy.

mirror_test() accommodated this noisiness by giving the counters an
allowance of several packets. But that only works up to a point, and on
busy systems won't be always enough.

In this patch set, clean up and stabilize the mirroring selftests. The
original intention was to port the tests over to UDP, but the logic of
ICMP ends up being so entangled in the mirroring selftests that the
changes feel overly invasive. Instead, ICMP is kept, but where possible,
we match on ICMP message type, thus filtering out hits by other ICMP
messages.

Where this is not practical (where the counter tap is put on a device
that carries encapsulated packets), switch the counter condition to _at
least_ X observed packets. This is less robust, but barely so --
probably the only scenario that this would not catch is something like
erroneous packet duplication, which would hopefully get caught by the
numerous other tests in this extensive suite.

- Patches #1 to #3 clean up parameters at various helpers.

- Patches #4 to #6 stabilize the mirroring selftests as described above.

- Mirroring tests currently allow testing SW datapath even on HW
  netdevices by trapping traffic to the SW datapath. This complicates
  the tests a bit without a good reason: to test SW datapath, just run
  the selftests on the veth topology. Thus in patch #7, drop support for
  this dual SW/HW testing.

- At this point, some cleanups were either made possible by the previous
  patches, or were always possible. In patches #8 to #11, realize these
  cleanups.

- In patch #12, fix mlxsw mirror_gre selftest to respect setting TESTS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This test is unusual in that overriding TESTS does not change the tests to
be run. Split the individual tests into several functions and invoke them
through tests_run() as appropriate.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nothing calls these.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These functions are not used anymore.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The selftest does not use functions from mirror_gre_lib, ditch the import.

It does not use arping either, so drop the require_command as well.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch, the function test_span_failable() is always
called with should_fail=1. Drop the argument and streamline the code.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mirroring tests are currently run in a skip_hw and optionally a skip_sw
mode. The former tests the SW datapath, the latter the HW datapath, if
available. In order to be able to test SW datapath on HW loopbacks, traps
are installed on ingress to get traffic from the HW datapath to the SW one.
This adds an unnecessary complexity when it would be much simpler to just
use a veth-based topology to test the SW datapath. Thus drop all the code
that supports this dual testing.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.

The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.

As a result, the selftests are noisy, because besides the primary ICMP
traffic, any amount of other service traffic is mirrored as well.

mirror_test() accommodated this noisiness by giving the counters an
allowance of several packets. But in the previous patch, where possible,
counter taps were changed to match only on an exact ICMP message. At least
in those cases, we can demand an exact number of packets to match.

Where the tap is installed on a connective netdevice, the exact matching is
not practical (though with u32, anything is possible). In those places,
there should still be some leeway -- and probably bigger than before,
because experience shows that these tests are very noisy.

To that end, change mirror_test() so that it can be either called with an
exact number to expect, or with an expression. Where leeway is needed,
adjust callers to pass a ">= 10" instead of mere 10.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mirroring selftests work by sending ICMP traffic between two hosts.
Along the way, this traffic is mirrored to a gretap netdevice, and counter
taps are then installed strategically along the path of the mirrored
traffic to verify the mirroring took place.

The problem with this is that besides mirroring the primary traffic, any
other service traffic is mirrored as well. At the same time, because the
tests need to work in HW-offloaded scenarios, the ability of the device to
do arbitrary packet inspection should not be taken for granted. Most tests
therefore simply use matchall, one uses flower to match on IP address.

As a result, the selftests are noisy, because besides the primary ICMP
traffic, any amount of other service traffic is mirrored as well.

However, often the counter tap is installed at the remote end of the gretap
tunnel. Since this is a SW-datapath scenario anyway, we can make the filter
arbitrarily accurate.

Thus in this patch, add parameters forward_type and backward_type to
several mirroring test helpers, as some other helpers already have. Then
change do_test_span_dir_ips() to instead of installing one generic tap and
using it for test in both directions, install the tap for each direction
separately, matching on the ICMP type given by these parameters.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The test works by sending packets through a tunnel, whence they are
forwarded to a LAG. One of the LAG children is removed from the LAG prior
to the exercise, and the test then counts how many packets pass through the
other one. The issue with this is that it counts all packets, not just the
encapsulated ones.

So instead add a second gretap endpoint to receive the sent packets, and
check reception counters there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The argument $dir has a fallback value of "ingress". Move the fallback from
the usage site to the argument definition block to make the fact clearer.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The argument is not used by these functions except to propagate it for
ultimately no purpose.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In some functions, argument-forwarding through "$@" without listing the
individual arguments explicitly is fundamental to the operation of a
function. E.g. xfail_on_veth() should be able to run various tests in the
fail-to-xfail regime, and usage of "$@" is appropriate as an abstraction
mechanism. For functions such as simple_if_init(), $@ is a handy way to
pass an array.

In other functions, it's merely a mechanism to save some typing, which
however ends up obscuring the real arguments and makes life hard for those
that end up reading the code.

This patch adds some of the implicit function arguments and correspondingly
expands $@'s. In several cases this will come in handy as following patches
adjust the parameter lists.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Danielle Ratson says:

====================
Add ability to flash modules' firmware

CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.2.2 of revision
4.0 of the CMIS standard.

According to the CMIS standard, the firmware update process is done
using a CDB commands sequence.

CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.12 of revision 4.0.

Add a pair of new ethtool messages that allow:

* User space to trigger firmware update of transceiver modules

* The kernel to notify user space about the progress of the process

The user interface is designed to be asynchronous in order to avoid RTNL
being held for too long and to allow several modules to be updated
simultaneously. The interface is designed with CMIS compliant modules in
mind, but kept generic enough to accommodate future use cases, if these
arise.

The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:

* The upper layer that will be triggered from the module layer, is
 cmis_ fw_update.
* The lower one is cmis_cdb.

In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the cmis_cdb interface clean and
the cmis_fw_update specific to the cdb commands handling it.

The communication between the kernel and the driver will be done using
two ethtool operations that enable reading and writing the transceiver
module EEPROM.
The operation ethtool_ops::get_module_eeprom_by_page, that is already
implemented, will be used for reading from the EEPROM the CDB reply,
e.g. reading module setting, state, etc.
The operation ethtool_ops::set_module_eeprom_by_page, that is added in
the current patchset, will be used for writing to the EEPROM the CDB
command such as start firmware image, run firmware image, etc.

Therefore in order for a driver to implement module flashing, that
driver needs to implement the two functions mentioned above.

Patchset overview:
Patch #1-#2: Implement the EEPROM writing in mlxsw.
Patch #3: Define the interface between the kernel and user space.
Patch #4: Add ability to notify the flashing firmware progress.
Patch #5: Veto operations during flashing.
Patch #6: Add extended compliance codes.
Patch #7: Add the cdb layer.
Patch #8: Add the fw_update layer.
Patch #9: Add ability to flash transceiver modules' firmware.

v8:
	Patch #7:
	* In the ethtool_cmis_wait_for_cond() evaluate the condition once more
	  to decide if the error code should be -ETIMEDOUT or something else.
	* s/netdev_err/netdev_err_once.

v7:
	Patch #4:
		* Return -ENOMEM instead of PTR_ERR(attr) on
		  ethnl_module_fw_flash_ntf_put_err().
	Patch #9:
		* Fix Warning for not unlocking the spin_lock in the error flow
          	  on module_flash_fw_work_list_add().
		* Avoid the fall-through on ethnl_sock_priv_destroy().

v6:
	* Squash some of the last patch to patch #5 and patch #9.
	Patch #3:
		* Add paragraph in .rst file.
	Patch #4:
		* Reserve '1' more place on SKB for NUL terminator in
		  the error message string.
		* Add more prints on error flow, re-write the printing
		  function and add ethnl_module_fw_flash_ntf_put_err().
		* Change the communication method so notification will be
		  sent in unicast instead of multicast.
		* Add new 'struct ethnl_module_fw_flash_ntf_params' that holds
		  the relevant info for unicast communication and use it to
		  send notification to the specific socket.
		* s/nla_put_u64_64bit/nla_put_uint/
	Patch #7:
		* In ethtool_cmis_cdb_init(), Use 'const' for the 'params'
		  parameter.
	Patch #8:
		* Add a list field to struct ethtool_module_fw_flash for
		  module_fw_flash_work_list that will be presented in the next
		  patch.
		* Move ethtool_cmis_fw_update() cleaning to a new function that
		  will be represented in the next patch.
		* Move some of the fields in struct ethtool_module_fw_flash to
		  a separate struct, so ethtool_cmis_fw_update() will get only
		  the relevant parameters for it.
		* Edit the relevant functions to get the relevant params for
		  them.
		* s/CMIS_MODULE_READY_MAX_DURATION_USEC/CMIS_MODULE_READY_MAX_DURATION_MSEC
	Patch #9:
		* Add a paragraph in the commit message.
		* Rename labels in module_flash_fw_schedule().
		* Add info to genl_sk_priv_*() and implement the relevant
		  callbacks, in order to handle properly a scenario of closing
		  the socket from user space before the work item was ended.
		* Add a list the holds all the ethtool_module_fw_flash struct
		  that corresponds to the in progress work items.
		* Add a new enum for the socket types.
		* Use both above to identify a flashing socket, add it to the
		  list and when closing socket affect only the flashing type.
		* Create a new function that will get the work item instead of
		  ethtool_cmis_fw_update().
		* Edit the relevant functions to get the relevant params for
		  them.
		* The new function will call the old ethtool_cmis_fw_update(),
		  and do the cleaning, so the existence of the list should be
		  completely isolated in module.c.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the ability to flash the modules' firmware by implementing the
interface between the user space and the kernel.

Example from a succeeding implementation:

 # ethtool --flash-module-firmware swp40 file test.bin

 Transceiver module firmware flashing started for device swp40
 Transceiver module firmware flashing in progress for device swp40
 Progress: 99%
 Transceiver module firmware flashing completed for device swp40

In addition, add infrastructure that allows modules to set socket-specific
private data. This ensures that when a socket is closed from user space
during the flashing process, the right socket halts sending notifications
to user space until the work item is completed.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the CMIS standard, the firmware update process is done using
a CDB commands sequence.

Implement a work that will be triggered from the module layer in the
next patch the will initiate and execute all the CDB commands in order, to
eventually complete the firmware update process.

This flashing process includes, writing the firmware image, running the new
firmware image and committing it after testing, so that it will run upon
reset.

This work will also notify user space about the progress of the firmware
update process.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CDB (Command Data Block Message Communication) reads and writes are
performed on memory map pages 9Fh-AFh according to the CMIS standard,
section 8.20 of revision 5.2.
Page 9Fh is used to specify the CDB command to be executed and also
provides an area for a local payload (LPL).

According to the CMIS standard, the firmware update process is done using
a CDB commands sequence that will be implemented in the next patch.

The kernel interface that will implement the firmware update using CDB
command will include 2 layers that will be added under ethtool:

* The upper layer that will be triggered from the module layer, is
  cmis_fw_update.
* The lower one is cmis_cdb.

In the future there might be more operations to implement using CDB
commands. Therefore, the idea is to keep the CDB interface clean and the
cmis_fw_update specific to the CDB commands handling it.

These two layers will communicate using the API the consists of three
functions:

- struct ethtool_cmis_cdb *
  ethtool_cmis_cdb_init(struct net_device *dev,
			struct ethtool_module_fw_flash_params *params);
- void ethtool_cmis_cdb_fini(struct ethtool_cmis_cdb *cdb);
- int ethtool_cmis_cdb_execute_cmd(struct net_device *dev,
				   struct ethtool_cmis_cdb_cmd_args *args);

Add the CDB layer to support initializing, finishing and executing CDB
commands:

* The initialization process will include creating of an ethtool_cmis_cdb
  instance, querying the module CDB support, entering and validating the
  password from user space (CMD 0x0000) and querying the module features
  (CMD 0x0040).

* The finishing API will simply free the ethtool_cmis_cdb instance.

* The executing process will write the CDB command to EEPROM using
  set_module_eeprom_by_page() that was presented earlier, and will
  process the reply from EEPROM.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFF-8024 is used to define various constants re-used in several SFF
SFP-related specifications.

Add SFF-8024 extended compliance code definitions for CMIS compliant
modules and use them in the next patch to determine the firmware flashing
work.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some operations cannot be performed during the firmware flashing
process.

For example:

- Port must be down during the whole flashing process to avoid packet loss
  while committing reset for example.

- Writing to EEPROM interrupts the flashing process, so operations like
  ethtool dump, module reset, get and set power mode should be vetoed.

- Split port firmware flashing should be vetoed.

In order to veto those scenarios, add a flag in 'struct net_device' that
indicates when a firmware flash is taking place on the module and use it
to prevent interruptions during the process.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add progress notifications ability to user space while flashing modules'
firmware by implementing the interface between the user space and the
kernel.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

CMIS compliant modules such as QSFP-DD might be running a firmware that
can be updated in a vendor-neutral way by exchanging messages between
the host and the module as described in section 7.3.1 of revision 5.2 of
the CMIS standard.

Add a pair of new ethtool messages that allow:

* User space to trigger firmware update of transceiver modules

* The kernel to notify user space about the progress of the process

The user interface is designed to be asynchronous in order to avoid
RTNL being held for too long and to allow several modules to be
updated simultaneously. The interface is designed with CMIS compliant
modules in mind, but kept generic enough to accommodate future use
cases, if these arise.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the ethtool_ops::set_module_eeprom_by_page operation to allow
ethtool to write to a transceiver module EEPROM, in a similar fashion to
the ethtool_ops::get_module_eeprom_by_page operation.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethtool can already retrieve information from a transceiver module
EEPROM by invoking the ethtool_ops::get_module_eeprom_by_page operation.
Add a corresponding operation that allows ethtool to write to a
transceiver module EEPROM.

The new write operation is purely an in-kernel API and is not exposed to
user space.

The purpose of this operation is not to enable arbitrary read / write
access, but to allow the kernel to write to specific addresses as part
of transceiver module firmware flashing. In the future, more
functionality can be implemented on top of these read / write
operations.

Adjust the comments of the 'ethtool_module_eeprom' structure as it is
no longer used only for read access.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract known PHY IDs from Linux kernel realtek PHY driver
and convert them into supported compatible string list for
this DT binding document.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].

Un-embed the net_devices from struct lmac by converting them
into pointers, and allocating them dynamically. Use the leverage
alloc_netdev() to allocate the net_device object at
bgx_lmac_enable().

The free of the device occurs at bgx_lmac_disable().

 Do not free_netdevice() if bgx_lmac_enable() fails after lmac->netdev
is allocated, since bgx_lmac_disable() is called if bgx_lmac_enable()
fails, and lmac->netdev will be freed there (similarly to lmac->dmacs).

Link: https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240626173503.87636-1-leitao@debian.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This reverts commit 934c2999.
This triggered a usercopy BUG() in systems with HIGHMEM, reported
by the test robot in:
 https://lore.kernel.org/oe-lkp/202406161539.b5ff7b20-oliver.sang@intel.comSigned-off-by: Sagi Grimberg <sagi@grimberg.me>
Link: https://patch.msgid.link/20240626070153.759257-1-sagi@grimberg.meSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Aaron Conole says:

====================
selftests: net: Switch pmtu.sh to use the internal ovs script.

Currently, if a user wants to run pmtu.sh and cover all the provided test
cases, they need to install the Open vSwitch userspace utilities.  This
dependency is difficult for users as well as CI environments, because the
userspace build and setup may require lots of support and devel packages
to be installed, system setup to be correct, and things like permissions
and selinux policies to be properly configured.

The kernel selftest suite includes an ovs-dpctl.py utility which can
interact with the openvswitch module directly.  This lets developers and
CI environments run without needing too many extra dependencies - just
the pyroute2 python package.

This series enhances the ovs-dpctl utility to provide support for set()
and tunnel() flow specifiers, better ipv6 handling support, and the
ability to add tunnel vports, and LWT interfaces.  Finally, it modifies
the pmtu.sh script to call the ovs-dpctl.py utility rather than the
typical OVS userspace utilities.  The pmtu.sh can still fall back on
the Open vSwitch userspace utilities if the ovs-dpctl.py script can't
be used.
====================

Link: https://patch.msgid.link/20240625172245.233874-1-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The pmtu testing will require that the OVS module is installed,
so do that.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-8-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current pmtu test infrastucture requires an installed copy of the
ovs-vswitchd userspace.  This means that any automated or constrained
environments may not have the requisite tools to run the tests.  However,
the pmtu tests don't require any special classifier processing.  Indeed
they are only using the vswitchd in the most basic mode - as a NORMAL
switch.

However, the ovs-dpctl kernel utility can now program all the needed basic
flows to allow traffic to traverse the tunnels and provide support for at
least testing some basic pmtu scenarios.  More complicated flow pipelines
can be added to the internal ovs test infrastructure, but that is work for
the future.  For now, enable the most common cases - wide mega flows with
no other prerequisites.

Enhance the pmtu testing to try testing using the internal utility, first.
As a fallback, if the internal utility isn't running, then try with the
ovs-vswitchd userspace tools.

Additionally, make sure that when the pyroute2 package is not available
the ovs-dpctl utility will error out to properly signal an error has
occurred and skip using the internal utility.
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240625172245.233874-7-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current iteration of IPv6 support requires explicit fields to be set
in addition to not properly support the actual IPv6 addresses properly.
With this change, make it so that the ipv6() bare option is usable to
create wildcarded flows to match broad swaths of ipv6 traffic.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-6-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This will be used when setting details about the tunnel to use as
transport.  There is a difference between the ODP format between tunnel():
the 'key' flag is not actually a flag field, so we don't support it in the
same way that the vswitchd userspace supports displaying it.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240625172245.233874-5-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

These will be used in upcoming commits to set specific attributes for
interacting with tunnels.  Since set() will use the key parsing routine, we
also make sure to prepend it with an open paren, for the action parsing to
properly understand it.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-4-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Until recently, the ovs-dpctl utility was used with a limited actions set
and didn't need to have support for multiple similar actions.  However,
when adding support for tunnels, it will be important to support multiple
set() actions in a single flow.  When printing these actions, the existing
code will be unable to print all of the sets - it will only print the
first.

Refactor this code to be easier to read and support multiple actions of the
same type in an action list.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-3-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The OVS module can operate in conjunction with various types of
tunnel ports.  These are created as either explicit tunnel vport
types, OR by creating a tunnel interface which acts as an anchor
for the lightweight tunnel support.

This patch adds the ability to add tunnel ports to an OVS
datapath for testing various scenarios with tunnel ports.  With
this addition, the vswitch "plumbing" will at least be able to
push packets around using the tunnel vports.  Future patches
will add support for setting required tunnel metadata for lwts
in the datapath.  The end goal will be to push packets via these
tunnels, and will be used in an upcoming commit for testing the
path MTU.
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20240625172245.233874-2-aconole@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

With ARCH=s390, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/net/lcs.o

Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20240625-md-s390-drivers-s390-net-v2-1-5a8a2b2f2ae3@quicinc.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use display hints for formatting scalar attrs. This is specifically
useful for formatting IPv4 addresses carried typically as u32.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20240626201234.2572964-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-next-2024-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Johannes Berg says:

====================
Highlights this time are:

 - cfg80211/nl80211:
    * improvements for 6 GHz regulatory flexibility

 - mac80211:
    * use generic netdev stats
    * multi-link improvements/fixes

 - brcmfmac:
    * MFP support (to enable WPA3)

 - wilc1000:
    * suspend/resume improvements

 - iwlwifi:
    * remove support for older FW for new devices
    * fast resume (keeping the device configured)

 - wl18xx:
    * support newer firmware versions

* tag 'wireless-next-2024-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (100 commits)
  wifi: brcmfmac: of: Support interrupts-extended
  wifi: brcmsmac: advertise MFP_CAPABLE to enable WPA3
  net: rfkill: Correct return value in invalid parameter case
  wifi: mac80211: fix NULL dereference at band check in starting tx ba session
  wifi: iwlwifi: mvm: fix rs.h kernel-doc
  wifi: iwlwifi: fw: api: datapath: fix kernel-doc
  wifi: iwlwifi: fix remaining mistagged kernel-doc comments
  wifi: iwlwifi: fix prototype mismatch kernel-doc warnings
  wifi: iwlwifi: fix kernel-doc in iwl-fh.h
  wifi: iwlwifi: fix kernel-doc in iwl-trans.h
  wifi: iwlwifi: pcie: fix kernel-doc
  wifi: iwlwifi: dvm: fix kernel-doc warnings
  wifi: iwlwifi: mvm: don't log error for failed UATS table read
  wifi: iwlwifi: trans: make bad state warnings
  wifi: iwlwifi: fw: api: fix some kernel-doc
  wifi: iwlwifi: mvm: remove init_dbg module parameter
  wifi: iwlwifi: update the BA notification API
  wifi: iwlwifi: mvm: always unblock EMLSR on ROC end
  wifi: iwlwifi: mvm: use IWL_FW_CHECK for link ID check
  wifi: iwlwifi: mvm: don't flush BSSes on restart with MLD API
  ...
====================

Link: https://patch.msgid.link/20240627114135.28507-3-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

No conflicts.

Adjacent changes:
  e3f02f32 ("ionic: fix kernel panic due to multi-buffer handling")
  d9c04209 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Johannes Berg says:

====================
Just a few changes:
 - maintainers: Larry Finger sadly passed away
 - maintainers: ath trees are in their group now
 - TXQ FQ quantum configuration fix
 - TI wl driver: work around stuck FW in AP mode
 - mac80211: disable softirqs in some new code
   needing that

* tag 'wireless-2024-06-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
  MAINTAINERS: wifi: update ath.git location
  MAINTAINERS: Remembering Larry Finger
  wifi: mac80211: disable softirqs for queued frame handling
  wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values
  wifi: wlcore: fix wlcore AP mode
====================

Link: https://patch.msgid.link/20240627083627.15312-3-johannes@sipsolutions.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from can, bpf and netfilter.

  There are a bunch of regressions addressed here, but hopefully nothing
  spectacular. We are still waiting the driver fix from Intel, mentioned
  by Jakub in the previous networking pull.

  Current release - regressions:

   - core: add softirq safety to netdev_rename_lock

   - tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed
     TFO

   - batman-adv: fix RCU race at module unload time

  Previous releases - regressions:

   - openvswitch: get related ct labels from its master if it is not
     confirmed

   - eth: bonding: fix incorrect software timestamping report

   - eth: mlxsw: fix memory corruptions on spectrum-4 systems

   - eth: ionic: use dev_consume_skb_any outside of napi

  Previous releases - always broken:

   - netfilter: fully validate NFT_DATA_VALUE on store to data registers

   - unix: several fixes for OoB data

   - tcp: fix race for duplicate reqsk on identical SYN

   - bpf:
       - fix may_goto with negative offset
       - fix the corner case with may_goto and jump to the 1st insn
       - fix overrunning reservations in ringbuf

   - can:
       - j1939: recover socket queue on CAN bus error during BAM
         transmission
       - mcp251xfd: fix infinite loop when xmit fails

   - dsa: microchip: monitor potential faults in half-duplex mode

   - eth: vxlan: pull inner IP header in vxlan_xmit_one()

   - eth: ionic: fix kernel panic due to multi-buffer handling

  Misc:

   - selftest: unix tests refactor and a lot of new cases added"

* tag 'net-6.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
  net: mana: Fix possible double free in error handling path
  selftest: af_unix: Check SIOCATMARK after every send()/recv() in msg_oob.c.
  af_unix: Fix wrong ioctl(SIOCATMARK) when consumed OOB skb is at the head.
  selftest: af_unix: Check EPOLLPRI after every send()/recv() in msg_oob.c
  selftest: af_unix: Check SIGURG after every send() in msg_oob.c
  selftest: af_unix: Add SO_OOBINLINE test cases in msg_oob.c
  af_unix: Don't stop recv() at consumed ex-OOB skb.
  selftest: af_unix: Add non-TCP-compliant test cases in msg_oob.c.
  af_unix: Don't stop recv(MSG_DONTWAIT) if consumed OOB skb is at the head.
  af_unix: Stop recv(MSG_PEEK) at consumed OOB skb.
  selftest: af_unix: Add msg_oob.c.
  selftest: af_unix: Remove test_unix_oob.c.
  tracing/net_sched: NULL pointer dereference in perf_trace_qdisc_reset()
  netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers
  net: usb: qmi_wwan: add Telit FN912 compositions
  tcp: fix tcp_rcv_fastopen_synack() to enter TCP_CA_Loss for failed TFO
  ionic: use dev_consume_skb_any outside of napi
  net: dsa: microchip: fix wrong register write when masking interrupt
  Fix race for duplicate reqsk on identical SYN
  ibmvnic: Add tx check to prevent skb leak
  ...