When running the OS with a page size > 4 KB, we need to round up mappings
for regions that are not aligned to the OS's page size. We already avoid
block mappings for EfiRuntimeServicesCode/Data regions for other reasons,
but in the unlikely event that other unaliged regions exists that have the
EFI_MEMORY_RUNTIME attribute set, ensure that unaligned regions are always
mapped down to pages. This way, the overlapping page is guaranteed not to
be covered by a block mapping that needs to be split.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

To avoid triggering diagnostics in the MMU code that are finicky about
splitting block mappings into more granular mappings, ensure that regions
that are likely to appear in the Memory Attributes table as well as the
UEFI memory map are always mapped down to pages. This way, we can use
apply_to_page_range() instead of create_pgd_mapping() for the second pass,
which cannot split or merge block entries, and operates strictly on PTEs.

Note that this aligns the arm64 Memory Attributes table handling code with
the ARM code, which already uses apply_to_page_range() to set the strict
permissions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Add a bool parameter 'allow_block_mappings' to create_pgd_mapping() and
the various helper functions that it descends into, to give the caller
control over whether block entries may be used to create the mapping.

The UEFI runtime mapping routines will use this to avoid creating block
entries that would need to split up into page entries when applying the
permissions listed in the Memory Attributes firmware table.

This also replaces the block_mappings_allowed() helper function that was
added for DEBUG_PAGEALLOC functionality, but the resulting code is
functionally equivalent (given that debug_page_alloc does not operate on
EFI page table entries anyway)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ARM errata 819472, 826319, 827319 and 824069 for affected
Cortex-A53 cores demand to promote "dc cvau" instructions to
"dc civac". Since we allow userspace to also emit those instructions,
we should make sure that "dc cvau" gets promoted there too.
So lets grasp the nettle here and actually trap every userland cache
maintenance instruction once we detect at least one affected core in
the system.
We then emulate the instruction by executing it on behalf of userland,
promoting "dc cvau" to "dc civac" on the way and injecting access
fault back into userspace.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[catalin.marinas@arm.com: s/set_segfault/arm64_notify_segfault/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The code for injecting a signal into userland if a trapped instruction
fails emulation due to a _userland_ error (like an illegal address)
will be used more often with the next patch.
Factor out the core functionality into a separate function and use
that both for the existing trap handler and for the deprecated
instructions emulation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[catalin.marinas@arm.com: s/set_segfault/arm64_notify_segfault/]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Currently we call the (optional) enable function for CPU _features_
only. As CPU _errata_ descriptions share the same data structure and
having an enable function is useful for errata as well (for instance
to set bits in SCTLR), lets call it when enumerating erratas too.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The newly introduced dcache_by_line_op macro is used at least in
one occassion at the moment to issue a "dc cvau" instruction,
which is affected by ARM errata 819472, 826319, 827319 and 824069.
Change the macro to allow for alternative patching in there to
protect affected Cortex-A53 cores.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[catalin.marinas@arm.com: indentation fixups]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ARM errata 819472, 826319, 827319 and 824069 for affected
Cortex-A53 cores demand to promote "dc cvau" instructions to
"dc civac" as well.
Attribute the usage of the instruction in __flush_cache_user_range
to also be covered by our alternative patching efforts.
For that we introduce an assembly macro which both deals with
alternatives while still tagging the instructions as USER.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Commit 77ee306c ("arm64: alternatives: add enable parameter to
conditional asm macros") extended the alternative assembly macros.
Unfortunately this does not really work as one would expect, as the
enable parameter in fact correctly protects the alternative section
magic, but not the actual code sequences.
This results in having both the original instruction(s) _and_  the
alternative ones, if enable if false.
Since there is no user of this macros anyway, just revert it.

This reverts commit 77ee306c.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The memblock_alloc() and memblock_alloc_base() will panic on their own
if no free memory, remove pointless BUG_ON.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

As Kees Cook notes in the ARM counterpart of this patch [0]:

  The _etext position is defined to be the end of the kernel text code,
  and should not include any part of the data segments. This interferes
  with things that might check memory ranges and expect executable code
  up to _etext.

In particular, Kees is referring to the HARDENED_USERCOPY patch set [1],
which rejects attempts to call copy_to_user() on kernel ranges containing
executable code, but does allow access to the .rodata segment. Regardless
of whether one may or may not agree with the distinction, it makes sense
for _etext to have the same meaning across architectures.

So let's put _etext where it belongs, between .text and .rodata, and fix
up existing references to use __init_begin instead, which unlike _end_rodata
includes the exception and notes sections as well.

The _etext references in kaslr.c are left untouched, since its references
to [_stext, _etext) are meant to capture potential jump instruction targets,
and so disregarding .rodata is actually an improvement here.

[0] http://article.gmane.org/gmane.linux.kernel/2245084
[1] http://thread.gmane.org/gmane.linux.kernel.hardened.devel/2502Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

We currently open-code extracting the NUMA node of a memblock region,
which requires an ifdef to cater for !CONFIG_NUMA builds where the
memblock_region::nid field does not exist.

The generic memblock_get_region_node helper is intended to cater for
this. For CONFIG_HAVE_MEMBLOCK_NODE_MAP, builds this returns reg->nid,
and for for !CONFIG_HAVE_MEMBLOCK_NODE_MAP builds this is a static
inline that returns 0. Note that for arm64,
CONFIG_HAVE_MEMBLOCK_NODE_MAP is selected iff CONFIG_NUMA is.

This patch makes use of memblock_get_region_node to simplify the arm64
code. At the same time, we can move the nid variable definition into the
loop, as this is the only place it is used.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

To aid in debugging kexec problems or when adding new functionality to
kexec add a new routine kexec_image_info() and several inline pr_debug
statements.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Add three new files, kexec.h, machine_kexec.c and relocate_kernel.S to the
arm64 architecture that add support for the kexec re-boot mechanism
(CONFIG_KEXEC) on arm64 platforms.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: James Morse <james.morse@arm.com>
[catalin.marinas@arm.com: removed dead code following James Morse's comments]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Commit 68234df4 ("arm64: kill flush_cache_all()") removed the global
arm64 routines cpu_reset() and cpu_soft_restart() needed by the arm64
kexec and kdump support.  Add back a simplified version of
cpu_soft_restart() with some changes needed for kexec in the new files
cpu_reset.S, and cpu_reset.h.

When a CPU is reset it needs to be put into the exception level it had when
it entered the kernel. Update cpu_soft_restart() to accept an argument
which signals if the reset address should be entered at EL1 or EL2, and
add a new hypercall HVC_SOFT_RESTART which is used for the EL2 switch.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

kernel/smp.c has a fancy counter that keeps track of the number of CPUs
it marked as not-present and left in cpu_park_loop(). If there are any
CPUs spinning in here, features like kexec or hibernate may release them
by overwriting this memory.

This problem also occurs on machines using spin-tables to release
secondary cores.
After commit 44dbcc93 ("arm64: Fix behavior of maxcpus=N")
we bring all known cpus into the secondary holding pen, meaning this
memory can't be re-used by kexec or hibernate.

Add a function cpus_are_stuck_in_kernel() to determine if either of these
cases have occurred.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: cherry-picked from mainline for kexec dependency]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

This reverts commit 6b14c517.

The original patch and UBSAN+KASAN enabled causes Linux to fail to link
with:

lib/built-in.o: In function `get_signed_val':
lib/ubsan.c:93: undefined reference to `__ashlti3'
lib/ubsan.c:93: undefined reference to `__ashrti3'
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Currently we treat ESR_EL1 bit 24 as software-defined for distinguishing
instruction aborts from data aborts, but this bit is architecturally
RES0 for instruction aborts, and could be allocated for an arbitrary
purpose in future. Additionally, we hard-code the value in entry.S
without the mnemonic, making the code difficult to understand.

Instead, remove ESR_LNX_EXEC, and distinguish aborts based on the esr,
which we already pass to the sole use of ESR_LNX_EXEC. A new helper,
is_el0_instruction_abort() is added to make the logic clear. Any
instruction aborts taken from EL1 will already have been handled by
bad_mode, so we need not handle that case in the helper.

For consistency, the existing permission_fault helper is renamed to
is_permission_fault, and the return type is changed to bool. There
should be no functional changes as the return value was a boolean
expression, and the result is only used in another boolean expression.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Cc: Huang Shijie <shijie.huang@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Now that we have a helper to extract the EC from an ESR_ELx value, make
use of this in the arm64 KVM code for simplicity and consistency. There
should be no functional changes as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Cc: Huang Shijie <shijie.huang@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Several places open-code extraction of the EC field from an ESR_ELx
value, in subtly different ways. This is unfortunate duplication and
variation, and the precise logic used to extract the field is a
distraction.

This patch adds a new macro, ESR_ELx_EC(), to extract the EC field from
an ESR_ELx value in a consistent fashion.

Existing open-coded extractions in core arm64 code are moved over to the
new helper. KVM code is left as-is for the moment.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Huang Shijie <shijie.huang@arm.com>
Cc: Dave P Martin <dave.martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

we only initialize swiotlb when swiotlb_force is true or not all system
memory is DMA-able, this trivial optimization saves us 64MB when
swiotlb is not necessary.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ACPI 6.1 specification was recently released at the end of January
2016, but the arm64 kernel documentation for the use of ACPI was written
for the 5.1 version of the spec.  There were significant additions to the
spec that had not yet been mentioned -- for example, the 6.0 mechanisms
added to make it easier to define processors and low power idle states,
as well as the 6.1 addition allowing regular interrupts (not just from
GPIO) be used to signal ACPI general purpose events.

This patch reflects going back through and examining the specs in detail
and updating content appropriately.  Whilst there, a few odds and ends of
typos were caught as well.  This brings the documentation up to date with
ACPI 6.1 for arm64.
Signed-off-by: Al Stone <al.stone@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Roy Franz <roy.franz@hpe.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Add ARCH_HAS_KCOV to ARM64 config. To avoid potential crashes, disable
instrumentation of the files in arch/arm64/kvm/hyp/*.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The gcc support __SIZEOF_INT128__ and __int128 in arm64, thus,
enable ARCH_SUPPORTS_INT128 to make mul_u64_u32_shr() a bit
more efficient in scheduler.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Currently dump_mem attempts to dump memory in 64-bit chunks when
reporting a failure in 64-bit code, or 32-bit chunks when reporting a
failure in 32-bit code. We added code to handle these two cases
separately in commit e147ae6d ("arm64: modify the dump mem for
64 bit addresses").

However, in all cases dump_mem is called, the failing context is a
kernel rather than user context. Additionally dump_mem is assumed to
only be used for kernel contexts, as internally it switches to
KERNEL_DS, and its callers pass kernel stack bounds.

This patch removes the redundant 32-bit chunk logic and associated
compat parameter, largely reverting the aforementioned commit. For the
call in __die(), the check of in_interrupt() is removed also, as __die()
is only called in response to faults from the kernel's exception level,
and thus the !user_mode(regs) check is sufficient. Were this not the
case, the used of task_stack_page(tsk) to generate the stack bounds
would be erroneous.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

The upstream commit 1771c6e1
("x86/kasan: instrument user memory access API") added KASAN instrument to
x86 user memory access API, so added such instrument to ARM64 too.

Define __copy_to/from_user in C in order to add kasan_check_read/write call,
rename assembly implementation to __arch_copy_to/from_user.

Tested by test_kasan module.
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

For debugging purposes, it would be nice if we could export page tables
other than the swapper_pg_dir to userspace. To enable this, this patch
refactors the arm64 page table dumping code such that multiple tables
may be registered with the framework, and exported under debugfs.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

AArch64 is capable of 128-bit memory accesses without alignment
restrictions, which makes it both possible and highly practical to slurp
up a typical 20-byte IP header in just 2 loads. Implement our own
version of ip_fast_checksum() to take advantage of that, resulting in
considerably fewer instructions and memory accesses than the generic
version. We can also get more optimal code generation for csum_fold() by
defining it a slightly different way round from the generic version, so
throw that into the mix too.
Suggested-by: Luke Starrett <luke.starrett@broadcom.com>
Acked-by: Luke Starrett <luke.starrett@broadcom.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull UDF fixes and a reiserfs fix from Jan Kara:
 "A couple of udf fixes (most notably a bug in parsing UDF partitions
  which led to inability to mount recent Windows installation media) and
  a reiserfs fix for handling kstrdup failure"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  reiserfs: check kstrdup failure
  udf: Use correct partition reference number for metadata
  udf: Use IS_ERR when loading metadata mirror file entry
  udf: Don't BUG on missing metadata partition descriptor

Pull dmaengine fixes from Vinod Koul:
 "Some fixes has piled up, so time to send them upstream.

  These fixes include:
   - at_xdmac fixes for residue and other stuff
   - update MAINTAINERS for dma dt bindings
   - mv_xor fix for incorrect offset"

* tag 'dmaengine-fix-4.7-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mv_xor: Fix incorrect offset in dma_map_page()
  dmaengine: at_xdmac: double FIFO flush needed to compute residue
  dmaengine: at_xdmac: fix residue corruption
  dmaengine: at_xdmac: align descriptors on 64 bits
  MAINTAINERS: Add file patterns for dma device tree bindings

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoC platforms.  Most are smaller fixes.

  Two areas that are worth pointing out are:

   - OMAP had a handful of changes to voltage specs that caused a bit of
     churn, most of volume of change in this branch is due to this.

   - There are a couple of _rcuidle fixes from Paul that touch common
     code and came in through the OMAP tree since they were the ones who
     saw the problems.

 The rest is smaller changes across a handful of platforms"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  arm: Use _rcuidle for smp_cross_call() tracepoints
  MAINTAINERS: Add myself as reviewer of ARM FSL/NXP
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: imx6ul: Fix Micrel PHY mask
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  ARM: dts: socfpga: Add missing PHY phandle
  ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
  ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
  ARM: dts: sun6i: yones-toptech-bs1078-v2: Drop constraints on dc1sw regulator
  ARM: dts: sun6i: primo81: Drop constraints on dc1sw regulator
  ARM: dts: sunxi: Add OLinuXino Lime2 eMMC to the Makefile
  ...

OMAP-GPMC: Fixes for for v4.7-rc cycle:

- Fix omap gpmc EXTRADELAY timing. The DT provided timings
were wrongly used causing devices requiring extra delay timing
to fail.

* tag 'gpmc-omap-fixes-for-v4.7' of https://github.com/rogerq/linux:
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  + Linux 4.7-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Fix dra7 for hardware issues limiting L4Per and L3init power domains
  to on state. Without this the devices may not work correctly after
  some time of use because of asymmetric aging. And related to this,
  let's also remove the unusable states.

- Always select omap interconnect for am43x as otherwise the am43x
  only configurations will not boot properly. This can happen easily
  for any product kernels that leave out other SoCs to save memory.

- Fix DSS PLL2 addresses that have gone unused for now

- Select erratum 430973 for omap3, this is now safe to do and can
  save quite a bit of debugging time for people who may have left
  it out.

* tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  + Linux 4.7-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.7-rc cycle:

- Two boot warning fixes from the RCU tree that should have gotten
  merged several weeks ago already but did not because of issues
  with who merges them. Paul has now split the RCU warning fixes into
  sets for various maintainers.

- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes

- Fix PM for omap3 boards using timer12 and gptimer, like the
  original beagleboard

- Fix hangs on am437x-sk-evm by lowering the I2C bus speed

* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  arm: Use _rcuidle for smp_cross_call() tracepoints
  arm: Use _rcuidle tracepoint to allow use from idle
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch fixes a non-booting issue in Mainline.

When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start.  AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.

AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).

Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).

Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.

Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes.  This will ensure a working platform in the mean time.

NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.

Fixes: fe135c63 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

The i.MX fixes for 4.7:
 - Correct Micrel PHY mask to fix the issue that i.MX6UL ethernet works
   in U-Boot but not in kernel.

* tag 'imx-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx6ul: Fix Micrel PHY mask
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull ARM fixes from Russell King:
 "A couple of fixes for pmd_mknotpresent()/pmd_present() for LPAE
  systems"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8579/1: mm: Fix definition of pmd_mknotpresent
  ARM: 8578/1: mm: ensure pmd_present only checks the valid bit

Pull USB fixes from Greg KH:
 "Here are a bunch (65) of USB fixes for 4.7-rc4.  Sorry about the
  quantity, I've been slow in getting these out.

  The majority are the "normal" gadget, musb, and xhci fixes, that we
  all are used to.  There are also a few other tiny fixes resolving a
  number of reported issues that showed up in 4.7-rc1.

  All of these have been in linux-next"

* tag 'usb-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (65 commits)
  usbip: rate limit get_frame_number message
  usb: musb: sunxi: Remove bogus "Frees glue" comment
  usb: musb: sunxi: Fix NULL ptr deref when gadget is registered before musb
  usb: echi-hcd: Add ehci_setup check before echi_shutdown
  usb: host: ehci-msm: Conditionally call ehci suspend/resume
  MAINTAINERS: Add file patterns for usb device tree bindings
  usb: host: ehci-tegra: Avoid getting the same reset twice
  usb: host: ehci-tegra: Grab the correct UTMI pads reset
  USB: mos7720: delete parport
  USB: OHCI: Don't mark EDs as ED_OPER if scheduling fails
  phy: ti-pipe3: Program the DPLL even if it was already locked
  usb: musb: Stop bulk endpoint while queue is rotated
  usb: musb: Ensure rx reinit occurs for shared_fifo endpoints
  usb: musb: host: correct cppi dma channel for isoch transfer
  usb: musb: only restore devctl when session was set in backup
  usb: phy: Check initial state for twl6030
  usb: musb: Use normal module_init for 2430 glue
  usb: musb: Remove pm_runtime_set_irq_safe
  usb: musb: Remove extra PM runtime calls from 2430 glue layer
  usb: musb: Return error value from musb_mailbox
  ...