- 21 Mar, 2013 40 commits
-
-
Antti Palosaari authored
Detect automatically multiple chip versions and select configuration according to that. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Add support for tuners integrated to the IT9135 and IT9137. Signed-off-by:
-
Antti Palosaari authored
It is tuner driver for tuner integrated to the ITE IT9135 and IT9137 chips. I split it out from the current it913x-fe driver. Signed-off-by:
-
Kevin Baradon authored
My 15c2:0036 device floods syslog when a keypad key is pressed: Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2 Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fef2 Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2 Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2 Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2 This patch removes those messages from imon, following suggestion from Mauro. Unknown keys shall be correctly handled by rc/input layer. Signed-off-by:
Kevin Baradon <kevin.baradon@gmail.com> Signed-off-by:
-
Kevin Baradon authored
Some imon devices (like 15c2:0036) need a higher delay between send_packet calls. Default value is still 5ms to avoid regressions on already working hardware. Also use interruptible wait to avoid load average going too high (and let caller handle signals). Signed-off-by:
-
Federico Fuga authored
If no manager is connected to the vout device, the omapvid_init() function fails. No error condition is checked, and the device is started. Later on, when irq is serviced, a NULL pointer dereference occurs. Also, the isr routine must be registered only if no error occurs, otherwise the isr triggers without the proper setup, and the kernel oops again. To prevent this, the error condition is checked, and the streamon function exits with error. Also the isr registration call is moved after the setup procedure is completed. Reviewed-by:
Prabhakar Lad <prabhakar.lad@ti.com> Signed-off-by:
-
Dmitri Belimov authored
I found very small bug in xc5000 source. When set option debug=1 and listen a radio we see in dmesg xc5000: xc_SetTVStandard() Standard = M/N-NTSC/PAL-BTSC at all times. However, it should be, instead "FM Radio-INPUT1_MONO". That happens because xc5000_set_radio_freq() gets the correct value for VideoMode and AudioMode for radio and calls xc_SetTVStandard() where name of standard comes from the incorrect place priv->video_standard. This incorrect debug message makes debugging a little difficult. Signed-off-by:
Dmitry Belimov <d.belimov@gmail.com> Signed-off-by:
-
Paul Bolle authored
Release v2.6.30 removed the MT9M001_PCA9536_SWITCH and MT9V022_PCA9536_SWITCH Kconfig symbols, in commits 36034dc3 ("V4L/DVB (11032): mt9m001: allow setting of bus width from board code") and e958e27a ("V4L/DVB (11033): mt9v022: allow setting of bus width from board code"). These two commits removed all gpio related code from these two drivers. But they skipped removing their two selects of GPIO_PCA953X. Remove these now as they are outdated. Their dependencies can never evaluate to true anyhow. Signed-off-by:
Paul Bolle <pebolle@tiscali.nl> Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Sachin Kamat authored
module_platform_driver_probe() eliminates the boilerplate and simplifies the code. Signed-off-by:
Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by:
-
Sachin Kamat authored
module_platform_driver_probe() eliminates the boilerplate and simplifies the code. Signed-off-by:
-
Sachin Kamat authored
module_platform_driver_probe() eliminates the boilerplate and simplifies the code. Signed-off-by:
-
Sachin Kamat authored
Use the newly introduced devm_ioremap_resource() instead of devm_request_and_ioremap() which provides more consistent error handling. Signed-off-by:
-
Sachin Kamat authored
Use the newly introduced devm_ioremap_resource() instead of devm_request_and_ioremap() which provides more consistent error handling. Signed-off-by:
-
Sachin Kamat authored
Use the newly introduced devm_ioremap_resource() instead of devm_request_and_ioremap() which provides more consistent error handling. devm_ioremap_resource() provides its own error messages; so all explicit error messages can be removed from the failure code paths. Signed-off-by:
-
Sachin Kamat authored
Use the newly introduced devm_ioremap_resource() instead of devm_request_and_ioremap() which provides more consistent error handling. devm_ioremap_resource() provides its own error messages; so all explicit error messages can be removed from the failure code paths. Signed-off-by:
-
Andrei Andreyanau authored
This patch fixes the issue that appears when mt9v024 camera is used with the mt9v022 soc camera driver. The minimum total row time is 690 columns (horizontal width + horizontal blanking). The minimum horizontal blanking is 61. Thus, when the window width is set below 627, horizontal blanking must be increased. For the mt9v024 camera the values above are correct and for the mt9v022 camera the correct values are in the existing kernel driver. Signed-off-by:
Andrei Andreyanau <a.andreyanau@sam-solutions.net> Signed-off-by:
-
Guennadi Liakhovetski authored
A recent commit "[media] soc-camera: Push probe-time power management to drivers" causes an Oops during mt9m111 driver probing because its .ctx private data field is now dereferenced before it is initialised. Fix this by initialising the field earlier. Reported-by:
Javier Martin <javier.martin@vista-silicon.com> Signed-off-by:
-
Benoît Thébaudeau authored
Commit f9bd5843 changed V4L2_CID_EXPOSURE_AUTO from boolean to enum, and commit af8425c5 changed the creation of this control into a menu for the mt9m111. However, mt9m111_set_autoexposure() is still interpreting the value set for this control as a boolean, which also conflicts with the default value of this control set to V4L2_EXPOSURE_AUTO (0). This patch makes mt9m111_set_autoexposure() interpret the value set for V4L2_CID_EXPOSURE_AUTO as defined by enum v4l2_exposure_auto_type. Signed-off-by:
Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by:
-
Paul Bolle authored
The Kconfig entry for "TS2020 based tuners" defaults to modular if DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate the logic, so we are in line with all the similar entries in this file. Signed-off-by:
-
Manjunath Hadli authored
add support for TVP514x as a media entity and support for pad operations. The decoder supports 1 output pad. The default format code was V4L2_MBUS_FMT_YUYV10_2X10 changed it to V4L2_MBUS_FMT_UYVY8_2X8. Signed-off-by:
Manjunath Hadli <manjunath.hadli@ti.com> Signed-off-by:
-
Manjunath Hadli authored
A lot of SOCs including Texas Instruments Davinci family mainly use video decoders as input devices. This patch adds a flag 'MEDIA_ENT_T_V4L2_SUBDEV_DECODER' media entity type for decoder's. Along side updates the documentation for this media entity type. Signed-off-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Lad, Prabhakar authored
The patch adds support for THS7353 video amplifier. The the THS7353 amplifier is very much similar to the existing THS7303 video amplifier driver. This patch appropriately makes changes to the existing ths7303 driver and adds support for the THS7353. This patch also adds V4L2_IDENT_THS7353 for the THS7353 chip and appropriate changes to Kconfig file for building. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Martin Bugge <marbugge@cisco.com> Signed-off-by:
-
Sachin Kamat authored
module_platform_driver() eliminates the boilerplate and simplifies the code. Signed-off-by:
-
Alexandru Gheorghiu authored
Use resource_size function on resource object instead of explicit computation. Signed-off-by:
Alexandru Gheorghiu <gheorghiuandru@gmail.com> Acked-by:
Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by:
-
Ismael Luceno authored
Signed-off-by:
Ismael Luceno <ismael.luceno@corp.bluecherry.net> Signed-off-by:
-
Hans Verkuil authored
This prevents the kernel log from being spammed with these messages. By turning on the debug option you will see them again. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
-
Hans Verkuil authored
Some drivers have special memory requirements for their buffers, usually related to DMA (e.g. GFP_DMA or __GFP_DMA32). Make it possible to specify additional GFP flags for those buffers by adding a gfp_flags field to vb2_queue. Note that this field will be replaced in the future with a different mechanism, but that is still work in progress and we need this feature now so we won't be able to convert drivers with such requirements to vb2. Signed-off-by:
Federico Vaga <federico.vaga@gmail.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
The stats are cleared by the frontend. Don't do it at DTV_CLEAR. Signed-off-by: -
Mauro Carvalho Chehab authored
The DVBv3 signal strength indicator is bogus: it doesn't range from 0 to 65535 as it would be expected. Also, 0 means the max signal strength. Now that a better way to estimate it was added, use the new way. Signed-off-by: -
Mauro Carvalho Chehab authored
The AZ6007 driver released by Terratec has a better way to estimate the signal strength, at CtrlSigStrength(). Port it to the driver. It should be noticed that there are two parameters there that are tuner-specific. Signed-off-by: -
Mauro Carvalho Chehab authored
The original az6007 driver has the code to calculate such stats. Add it to the driver, reporting them via DVBv5 stats API. Signed-off-by: -
Mauro Carvalho Chehab authored
The BER code does nothing but filling it with zero. Remove it. Signed-off-by: -
Mauro Carvalho Chehab authored
drivers/media/common/siano/smsdvb-debugfs.c:51:6: warning: no previous prototype for 'smsdvb_print_dvb_stats' [-Wmissing-prototypes] drivers/media/common/siano/smsdvb-debugfs.c:154:6: warning: no previous prototype for 'smsdvb_print_isdb_stats' [-Wmissing-prototypes] drivers/media/common/siano/smsdvb-debugfs.c:244:6: warning: no previous prototype for 'smsdvb_print_isdb_stats_ex' [-Wmissing-prototypes] drivers/media/common/siano/smscoreapi.c:832:5: warning: no previous prototype for 'smscore_configure_board' [-Wmissing-prototypes] drivers/media/common/siano/smscoreapi.c:1301:5: warning: no previous prototype for 'smscore_init_device' [-Wmissing-prototypes] Signed-off-by: -
Mauro Carvalho Chehab authored
Fix all other remaining checkpatch.pl compliants on the Siano driver, except for the 80-cols (soft) limit. Those are harder to fix, and probably not worth to do right now. Signed-off-by: -
Mauro Carvalho Chehab authored
Remove the remaining CamelCase checkpatch.pl compliants. There are still a few left, but those are due to USB and DVB APIs. Signed-off-by: -
Mauro Carvalho Chehab authored
Fix the remaining checkpatch.pl compliants at smscoreapi.h, except by the "line over 80 characters" on comments. Fixing those would require more time, as the better is to convert them into the struct descriptions used inside the kernel, as described at: Documentation/kernel-doc-nano-HOWTO.txt Signed-off-by: -
Mauro Carvalho Chehab authored
There are several structures defined in uppercase. Convert them to lowercase, and simplify their names, when possible. Signed-off-by: -
Mauro Carvalho Chehab authored
It is almost impossible to see a compliant with checkpatch.pl on those Siano drivers, as there are simply too much violations on it. So, now that a big change was done, the better is to cleanup the checkpatch compliants. Let's first replace all CammelCase symbols found at smscoreapi.h using camel_case namespace. That removed 144 checkpatch.pl compliants on this file. Of course, the other files need to be fixed accordingly. Signed-off-by: -
Mauro Carvalho Chehab authored
This driver can use several firmwares. Provide such info at module firmware metadata. Signed-off-by:
-
