- 18 Jul, 2017 40 commits
-
-
Takashi Iwai authored
commit f363a066 upstream. In the commit [15c75b09: ALSA: ctxfi: Fallback DMA mask to 32bit], I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while cthw20k2.c is OK). This patch fixes that obvious bug. (As a side note: although the original commit was completely wrong, it's still working for most of machines, as it sets to 32bit DMA mask in the end. So the bug severity is low.) Fixes: 15c75b09 ("ALSA: ctxfi: Fallback DMA mask to 32bit") Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Bjørn Mork authored
commit 436ecf55 upstream. This is a Dell branded Sierra Wireless EM7455. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Daniel Borkmann authored
commit e7ede72a upstream. The current symbols__fixup_end() heuristic for the last entry in the rb tree is suboptimal as it leads to not being able to recognize the symbol in the call graph in a couple of corner cases, for example: i) If the symbol has a start address (f.e. exposed via kallsyms) that is at a page boundary, then the roundup(curr->start, 4096) for the last entry will result in curr->start == curr->end with a symbol length of zero. ii) If the symbol has a start address that is shortly before a page boundary, then also here, curr->end - curr->start will just be very few bytes, where it's unrealistic that we could perform a match against. Instead, change the heuristic to roundup(curr->start, 4096) + 4096, so that we can catch such corner cases and have a better chance to find that specific symbol. It's still just best effort as the real end of the symbol is unknown to us (and could even be at a larger offset than the current range), but better than the current situation. Alexei reported that he recently run into case i) with a JITed eBPF program (these are all page aligned) as the last symbol which wasn't properly shown in the call graph (while other eBPF program symbols in the rb tree were displayed correctly). Since this is a generic issue, lets try to improve the heuristic a bit. Reported-and-Tested-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Fixes: 2e538c4a ("perf tools: Improve kernel/modules symbol lookup") Link: http://lkml.kernel.org/r/bb5c80d27743be6f12afc68405f1956a330e1bc9.1489614365.git.daniel@iogearbox.netSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Robert Middleton authored
commit 2cd29f23 upstream. When an interrupt occurs on an MCP23S08 chip, the INTF register will only contain one bit as causing the interrupt. If more than two pins change at the same time on the chip, this causes one of the pins to not be reported. This patch fixes the logic for checking if a pin has changed, so that multiple pins will always cause more than one change. Signed-off-by:
Robert Middleton <robert.middleton@rm5248.com> Tested-by:
Phil Reid <preid@electromag.com.au> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [bwh: Backported to 3.16: - No support for level-triggered interrupts - Use mcp->ops->read instead of mcp_read() - Device pointer for logging is mcp->chip.dev] Signed-off-by:
-
Guenter Roeck authored
commit 7b2db29f upstream. If usb_get_bos_descriptor() returns an error, usb->bos will be NULL. Nevertheless, it is dereferenced unconditionally in hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set. This results in a crash. usb 5-1: unable to get BOS descriptor ... Unable to handle kernel NULL pointer dereference at virtual address 00000008 pgd = ffffffc00165f000 [00000008] *pgd=000000000174f003, *pud=000000000174f003, *pmd=0000000001750003, *pte=00e8000001751713 Internal error: Oops: 96000005 [#1] PREEMPT SMP Modules linked in: uinput uvcvideo videobuf2_vmalloc cmac [ ... ] CPU: 5 PID: 3353 Comm: kworker/5:3 Tainted: G B 4.4.52 #480 Hardware name: Google Kevin (DT) Workqueue: events driver_set_config_work task: ffffffc0c3690000 ti: ffffffc0ae9a8000 task.ti: ffffffc0ae9a8000 PC is at hub_port_init+0xc3c/0xd10 LR is at hub_port_init+0xc3c/0xd10 ... Call trace: [<ffffffc0007fbbfc>] hub_port_init+0xc3c/0xd10 [<ffffffc0007fbe2c>] usb_reset_and_verify_device+0x15c/0x82c [<ffffffc0007fc5e0>] usb_reset_device+0xe4/0x298 [<ffffffbffc0e3fcc>] rtl8152_probe+0x84/0x9b0 [r8152] [<ffffffc00080ca8c>] usb_probe_interface+0x244/0x2f8 [<ffffffc000774a24>] driver_probe_device+0x180/0x3b4 [<ffffffc000774e48>] __device_attach_driver+0xb4/0xe0 [<ffffffc000772168>] bus_for_each_drv+0xb4/0xe4 [<ffffffc0007747ec>] __device_attach+0xd0/0x158 [<ffffffc000775080>] device_initial_probe+0x24/0x30 [<ffffffc0007739d4>] bus_probe_device+0x50/0xe4 [<ffffffc000770bd0>] device_add+0x414/0x738 [<ffffffc000809fe8>] usb_set_configuration+0x89c/0x914 [<ffffffc00080a120>] driver_set_config_work+0xc0/0xf0 [<ffffffc000249bb8>] process_one_work+0x390/0x6b8 [<ffffffc00024abcc>] worker_thread+0x480/0x610 [<ffffffc000251a80>] kthread+0x164/0x178 [<ffffffc0002045d0>] ret_from_fork+0x10/0x40 Since we don't know anything about LPM capabilities without BOS descriptor, don't attempt to enable LPM if it is not available. Fixes: 890dae88 ("xhci: Enable LPM support only for hardwired ...") Cc: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Oliver Neukum authored
commit cdd7928d upstream. The gadget code exports the bitfield for serial status changes over the wire in its internal endianness. The fix is to convert to little endian before sending it over the wire. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Tested-by:
家瑋 <momo1208@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 687e0687 upstream. USBTMC devices are required to have a bulk-in and a bulk-out endpoint, but the driver failed to verify this, something which could lead to the endpoint addresses being taken from uninitialised memory. Make sure to zero all private data as part of allocation, and add the missing endpoint sanity check. Note that this also addresses a more recently introduced issue, where the interrupt-in-presence flag would also be uninitialised whenever the optional interrupt-in endpoint is not present. This in turn could lead to an interrupt urb being allocated, initialised and submitted based on uninitialised values. Fixes: dbf3e7f6 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f67 ("USB: add USB test and measurement class driver") Signed-off-by:
-
David Ahern authored
commit 4ee39733 upstream. Anycast routes have the RTF_ANYCAST flag set, but when dumping routes for userspace the route type is not set to RTN_ANYCAST. Make it so. Fixes: 58c4fb86 ("[IPV6]: Flag RTF_ANYCAST for anycast routes") CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Johan Hovold authored
commit 92461f5d upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Fixes: bdb5c57f ("Input: add sur40 driver for Samsung SUR40... ") Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit cb1b4946 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Signed-off-by:
-
Johan Hovold authored
commit ba340d7b upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: bba5394a ("Input: add support for Hanwang tablets") Signed-off-by:
-
Johan Hovold authored
commit 5cc4a1a9 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: aca951a2 ("[PATCH] input-driver-yealink-P1K-usb-phone") Signed-off-by:
-
Johan Hovold authored
commit 1916d319 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack control-interface endpoints. Fixes: 628329d5 ("Input: add IMS Passenger Control Unit driver") Signed-off-by:
-
Johan Hovold authored
commit ac2ee9ba upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: c04148f9 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by:
-
Johan Hovold authored
commit 59cf8bed upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory that lie beyond the end of the endpoint array should a malicious device lack the expected endpoints. Signed-off-by:
-
Johan Hovold authored
commit 181302dc upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 53f3a9e2 ("mmc: USB SD Host Controller (USHC) driver") Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Peter Zijlstra authored
commit e7cc4865 upstream. While hunting for clues to a use-after-free, Oleg spotted that perf_event_init_context() can loose an error value with the result that fork() can succeed even though we did not fully inherit the perf event context. Spotted-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: oleg@redhat.com Fixes: 889ff015 ("perf/core: Split context's event group list into pinned and non-pinned lists") Link: http://lkml.kernel.org/r/20170316125823.190342547@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Johannes Berg authored
commit ea90e0dc upstream. Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out to be perfectly accurate - there are various error paths that miss unlock of the RTNL. To fix those, change the locking a bit to not be conditional in all those nl80211_prepare_*_dump() functions, but make those require the RTNL to start with, and fix the buggy error paths. This also let me use sparse (by appropriately overriding the rtnl_lock/rtnl_unlock functions) to validate the changes. Reported-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.16: - Drop changes to nl80211_dump_interface(), nl80211_dump_mpp(), nl80211_prepare_vendor_dump(), nl80211_vendor_cmd_dump() - Adjust context] Signed-off-by:
-
Matt Fleming authored
commit 6e5f32f7 upstream. If we crossed a sample window while in NO_HZ we will add LOAD_FREQ to the pending sample window time on exit, setting the next update not one window into the future, but two. This situation on exiting NO_HZ is described by: this_rq->calc_load_update < jiffies < calc_load_update In this scenario, what we should be doing is: this_rq->calc_load_update = calc_load_update [ next window ] But what we actually do is: this_rq->calc_load_update = calc_load_update + LOAD_FREQ [ next+1 window ] This has the effect of delaying load average updates for potentially up to ~9seconds. This can result in huge spikes in the load average values due to per-cpu uninterruptible task counts being out of sync when accumulated across all CPUs. It's safe to update the per-cpu active count if we wake between sample windows because any load that we left in 'calc_load_idle' will have been zero'd when the idle load was folded in calc_global_load(). This issue is easy to reproduce before, commit 9d89c257 ("sched/fair: Rewrite runnable load and utilization average tracking") just by forking short-lived process pipelines built from ps(1) and grep(1) in a loop. I'm unable to reproduce the spikes after that commit, but the bug still seems to be present from code review. Signed-off-by:
Matt Fleming <matt@codeblueprint.co.uk> Signed-off-by:
-
Eric Dumazet authored
commit 22a0e18e upstream. I mistakenly added the code to release sk->sk_frag in sk_common_release() instead of sk_destruct() TCP sockets using sk->sk_allocation == GFP_ATOMIC do no call sk_common_release() at close time, thus leaking one (order-3) page. iSCSI is using such sockets. Fixes: 5640f768 ("net: use a per task frag allocator") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Michael Engl authored
commit e83bb3e6 upstream. The tiadc_irq_h(int irq, void *private) function is handling FIFO overruns by clearing flags, disabling and enabling the ADC to recover. If the ADC is running in continuous mode a FIFO overrun happens regularly. If the disabling of the ADC happens concurrently with a new conversion. It might happen that the enabling of the ADC is ignored by the hardware. This stops the ADC permanently. No more interrupts are triggered. According to the AM335x Reference Manual (SPRUH73H October 2011 - Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to check the ADC FSM bits in REG_ADCFSM before enabling the ADC again. Because the disabling of the ADC is done right after the current conversion has been finished. To trigger this bug it is necessary to run the ADC in continuous mode. The ADC values of all channels need to be read in an endless loop. The bug appears within the first 6 hours (~5.4 million handled FIFO overruns). The user space application will hang on reading new values from the character device. Fixes: ca9a5638 ("iio: ti_am335x_adc: Add continuous sampling support") Signed-off-by:
Michael Engl <michael.engl@wjw-solutions.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Eric Biggers authored
commit b9cf625d upstream. If ext4_convert_inline_data() was called on a directory with inline data, the filesystem was left in an inconsistent state (as considered by e2fsck) because the file size was not increased to cover the new block. This happened because the inode was not marked dirty after i_disksize was updated. Fix this by marking the inode dirty at the end of ext4_finish_convert_inline_dir(). This bug was probably not noticed before because most users mark the inode dirty afterwards for other reasons. But if userspace executed FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by 'kvm-xfstests -c adv generic/396', then the inode was never marked dirty after updating i_disksize. Fixes: 3c47d541Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Peter Zijlstra authored
commit 9bbb25af upstream. Thomas spotted that fixup_pi_state_owner() can return errors and we fail to unlock the rt_mutex in that case. Reported-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Cc: juri.lelli@arm.com Cc: bigeasy@linutronix.de Cc: xlpang@redhat.com Cc: rostedt@goodmis.org Cc: mathieu.desnoyers@efficios.com Cc: jdesfossez@efficios.com Cc: dvhart@infradead.org Cc: bristot@redhat.com Link: http://lkml.kernel.org/r/20170304093558.867401760@infradead.orgSigned-off-by:
-
Peter Zijlstra authored
commit c236c8e9 upstream. While working on the futex code, I stumbled over this potential use-after-free scenario. Dmitry triggered it later with syzkaller. pi_mutex is a pointer into pi_state, which we drop the reference on in unqueue_me_pi(). So any access to that pointer after that is bad. Since other sites already do rt_mutex_unlock() with hb->lock held, see for example futex_lock_pi(), simply move the unlock before unqueue_me_pi(). Reported-by:
-
Anssi Hannula authored
commit 16681037 upstream. sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 << (13 + divisor)). However, the divisor is not some Arasan-specific value, but instead is just the Data Timeout Counter Value from the SDHCI Timeout Control Register. Applying it here like this is wrong as the sdhci driver already takes that value into account when calculating timeouts, and in fact it *sets* that register value based on how long a timeout is wanted. Additionally, sdhci core interprets the .get_timeout_clock callback return value as if it were read from hardware registers, i.e. the unit should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit. This bit is set at least on the tested Zynq-7000 SoC. With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in too high a timeout clock rate being reported, causing the core to use longer-than-needed timeouts. Additionally, on a partitioned MMC (therefore having erase_group_def bit set) mmc_calc_max_discard() disables discard support as it looks like controller does not support the long timeouts needed for that. Do not apply the extra divisor and return the timeout clock in the expected unit. Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR eMMC card. Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Fixes: e3ec3a3d ("mmc: arasan: Add driver for Arasan SDHCI") Signed-off-by:
-
Dan Williams authored
commit 6e9f44ea upstream. Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by qcserial due to a USB VID/PID conflict with an existing Acer device. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Samuel Thibault authored
commit 3243367b upstream. Some USB 2.0 devices erroneously report millisecond values in bInterval. The generic config code manages to catch most of them, but in some cases it's not completely enough. The case at stake here is a USB 2.0 braille device, which wants to announce 10ms and thus sets bInterval to 10, but with the USB 2.0 computation that yields to 64ms. It happens that one can type fast enough to reach this interval and get the device buffers overflown, leading to problematic latencies. The generic config code does not catch this case because the 64ms is considered a sane enough value. This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk to mark devices which actually report milliseconds in bInterval, and marks Vario Ultra devices as needing it. Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Johan Hovold authored
commit 4ce36271 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the cmd and wait_init_done callbacks which are called during probe. Fixes: 1ba47da5 ("uwb: add the i1480 DFU driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit daf229b1 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Note that the dereference happens in the start callback which is called during probe. Fixes: de520b8b ("uwb: add HWA radio controller driver") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit 03ace948 upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. This specifically fixes the NULL-pointer dereference when probing HWA HC devices. Fixes: df365423 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Johan Hovold authored
commit f259ca3e upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. Note that the endpoint access that causes the NULL-deref is currently only used for debugging purposes during probe so the oops only happens when dynamic debugging is enabled. This means the driver could be rewritten to continue to accept device with only two endpoints, should such devices exist. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Johan Hovold authored
commit b0addd3f upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Jon Maxwell authored
commit 45caeaa5 upstream. As Eric Dumazet pointed out this also needs to be fixed in IPv6. v2: Contains the IPv6 tcp/Ipv6 dccp patches as well. We have seen a few incidents lately where a dst_enty has been freed with a dangling TCP socket reference (sk->sk_dst_cache) pointing to that dst_entry. If the conditions/timings are right a crash then ensues when the freed dst_entry is referenced later on. A Common crashing back trace is: #8 [] page_fault at ffffffff8163e648 [exception RIP: __tcp_ack_snd_check+74] . . #9 [] tcp_rcv_established at ffffffff81580b64 #10 [] tcp_v4_do_rcv at ffffffff8158b54a #11 [] tcp_v4_rcv at ffffffff8158cd02 #12 [] ip_local_deliver_finish at ffffffff815668f4 #13 [] ip_local_deliver at ffffffff81566bd9 #14 [] ip_rcv_finish at ffffffff8156656d #15 [] ip_rcv at ffffffff81566f06 #16 [] __netif_receive_skb_core at ffffffff8152b3a2 #17 [] __netif_receive_skb at ffffffff8152b608 #18 [] netif_receive_skb at ffffffff8152b690 #19 [] vmxnet3_rq_rx_complete at ffffffffa015eeaf [vmxnet3] #20 [] vmxnet3_poll_rx_only at ffffffffa015f32a [vmxnet3] #21 [] net_rx_action at ffffffff8152bac2 #22 [] __do_softirq at ffffffff81084b4f #23 [] call_softirq at ffffffff8164845c #24 [] do_softirq at ffffffff81016fc5 #25 [] irq_exit at ffffffff81084ee5 #26 [] do_IRQ at ffffffff81648ff8 Of course it may happen with other NIC drivers as well. It's found the freed dst_entry here: 224 static bool tcp_in_quickack_mode(struct sock *sk)
↩ 225 {↩ 226 ▹ const struct inet_connection_sock *icsk = inet_csk(sk);↩ 227 ▹ const struct dst_entry *dst = __sk_dst_get(sk);↩ 228↩ 229 ▹ return (dst && dst_metric(dst, RTAX_QUICKACK)) ||↩ 230 ▹ ▹ (icsk->icsk_ack.quick && !icsk->icsk_ack.pingpong);↩ 231 }↩ But there are other backtraces attributed to the same freed dst_entry in netfilter code as well. All the vmcores showed 2 significant clues: - Remote hosts behind the default gateway had always been redirected to a different gateway. A rtable/dst_entry will be added for that host. Making more dst_entrys with lower reference counts. Making this more probable. - All vmcores showed a postitive LockDroppedIcmps value, e.g: LockDroppedIcmps 267 A closer look at the tcp_v4_err() handler revealed that do_redirect() will run regardless of whether user space has the socket locked. This can result in a race condition where the same dst_entry cached in sk->sk_dst_entry can be decremented twice for the same socket via: do_redirect()->__sk_dst_check()-> dst_release(). Which leads to the dst_entry being prematurely freed with another socket pointing to it via sk->sk_dst_cache and a subsequent crash. To fix this skip do_redirect() if usespace has the socket locked. Instead let the redirect take place later when user space does not have the socket locked. The dccp/IPv6 code is very similar in this respect, so fixing it there too. As Eric Garver pointed out the following commit now invalidates routes. Which can set the dst->obsolete flag so that ipv4_dst_check() returns null and triggers the dst_release(). Fixes: ceb33206 ("ipv4: Kill routes during PMTU/redirect updates.") Cc: Eric Garver <egarver@redhat.com> Cc: Hannes Sowa <hsowa@redhat.com> Signed-off-by:Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 6e526fdf upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer or accessing memory beyond the endpoint array should a malicious device lack the expected endpoints. The endpoints are specifically dereferenced in the i2400m_bootrom_init path during probe (e.g. in i2400mu_tx_bulk_out). Fixes: f398e424 ("i2400m/USB: probe/disconnect, dev init/shutdown and reset backends") Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com> Signed-off-by:
-
Johan Hovold authored
commit 68c32f9c upstream. Make sure to check the number of endpoints to avoid dereferencing a NULL-pointer should a malicious device lack endpoints. Fixes: cf7776dc ("[PATCH] isdn4linux: Siemens Gigaset drivers - direct USB connection") Cc: Hansjoerg Lipp <hjlipp@web.de> Signed-off-by:
-
Sabrina Dubroca authored
commit 67e19400 upstream. Commit 27596472 ("ipv6: fix ECMP route replacement") introduced a loop that removes all siblings of an ECMP route that is being replaced. However, this loop doesn't stop when it has replaced siblings, and keeps removing other routes with a higher metric. We also end up triggering the WARN_ON after the loop, because after this nsiblings < 0. Instead, stop the loop when we have taken care of all routes with the same metric as the route being replaced. Reproducer: =========== #!/bin/sh ip netns add ns1 ip netns add ns2 ip -net ns1 link set lo up for x in 0 1 2 ; do ip link add veth$x netns ns2 type veth peer name eth$x netns ns1 ip -net ns1 link set eth$x up ip -net ns2 link set veth$x up done ip -net ns1 -6 r a 2000::/64 nexthop via fe80::0 dev eth0 \ nexthop via fe80::1 dev eth1 nexthop via fe80::2 dev eth2 ip -net ns1 -6 r a 2000::/64 via fe80::42 dev eth0 metric 256 ip -net ns1 -6 r a 2000::/64 via fe80::43 dev eth0 metric 2048 echo "before replace, 3 routes" ip -net ns1 -6 r | grep -v '^fe80\|^ff00' echo ip -net ns1 -6 r c 2000::/64 nexthop via fe80::4 dev eth0 \ nexthop via fe80::5 dev eth1 nexthop via fe80::6 dev eth2 echo "after replace, only 2 routes, metric 2048 is gone" ip -net ns1 -6 r | grep -v '^fe80\|^ff00' Fixes: 27596472 ("ipv6: fix ECMP route replacement") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by:
Xin Long <lucien.xin@gmail.com> Reviewed-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
Kinglong Mee authored
commit 366a1569 upstream. Because nfs4_opendata_access() has close the state when access is denied, so the state isn't leak. Rather than revert the commit a974deee, I'd like clean the strange state close. [ 1615.094218] ------------[ cut here ]------------ [ 1615.094607] WARNING: CPU: 0 PID: 23702 at lib/list_debug.c:31 __list_add_valid+0x8e/0xa0 [ 1615.094913] list_add double add: new=ffff9d7901d9f608, prev=ffff9d7901d9f608, next=ffff9d7901ee8dd0. [ 1615.095458] Modules linked in: nfsv4(E) nfs(E) nfsd(E) tun bridge stp llc fuse ip_set nfnetlink vmw_vsock_vmci_transport vsock f2fs snd_seq_midi snd_seq_midi_event fscrypto coretemp ppdev crct10dif_pclmul crc32_pclmul ghash_clmulni_intel intel_rapl_perf vmw_balloon snd_ens1371 joydev gameport snd_ac97_codec ac97_bus snd_seq snd_pcm snd_rawmidi snd_timer snd_seq_device snd soundcore nfit parport_pc parport acpi_cpufreq tpm_tis tpm_tis_core tpm i2c_piix4 vmw_vmci shpchp auth_rpcgss nfs_acl lockd(E) grace sunrpc(E) xfs libcrc32c vmwgfx drm_kms_helper ttm drm crc32c_intel mptspi e1000 serio_raw scsi_transport_spi mptscsih mptbase ata_generic pata_acpi fjes [last unloaded: nfs] [ 1615.097663] CPU: 0 PID: 23702 Comm: fstest Tainted: G W E 4.11.0-rc1+ #517 [ 1615.098015] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015 [ 1615.098807] Call Trace: [ 1615.099183] dump_stack+0x63/0x86 [ 1615.099578] __warn+0xcb/0xf0 [ 1615.099967] warn_slowpath_fmt+0x5f/0x80 [ 1615.100370] __list_add_valid+0x8e/0xa0 [ 1615.100760] nfs4_put_state_owner+0x75/0xc0 [nfsv4] [ 1615.101136] __nfs4_close+0x109/0x140 [nfsv4] [ 1615.101524] nfs4_close_state+0x15/0x20 [nfsv4] [ 1615.101949] nfs4_close_context+0x21/0x30 [nfsv4] [ 1615.102691] __put_nfs_open_context+0xb8/0x110 [nfs] [ 1615.103155] put_nfs_open_context+0x10/0x20 [nfs] [ 1615.103586] nfs4_file_open+0x13b/0x260 [nfsv4] [ 1615.103978] do_dentry_open+0x20a/0x2f0 [ 1615.104369] ? nfs4_copy_file_range+0x30/0x30 [nfsv4] [ 1615.104739] vfs_open+0x4c/0x70 [ 1615.105106] ? may_open+0x5a/0x100 [ 1615.105469] path_openat+0x623/0x1420 [ 1615.105823] do_filp_open+0x91/0x100 [ 1615.106174] ? __alloc_fd+0x3f/0x170 [ 1615.106568] do_sys_open+0x130/0x220 [ 1615.106920] ? __put_cred+0x3d/0x50 [ 1615.107256] SyS_open+0x1e/0x20 [ 1615.107588] entry_SYSCALL_64_fastpath+0x1a/0xa9 [ 1615.107922] RIP: 0033:0x7fab599069b0 [ 1615.108247] RSP: 002b:00007ffcf0600d78 EFLAGS: 00000246 ORIG_RAX: 0000000000000002 [ 1615.108575] RAX: ffffffffffffffda RBX: 00007fab59bcfae0 RCX: 00007fab599069b0 [ 1615.108896] RDX: 0000000000000200 RSI: 0000000000000200 RDI: 00007ffcf060255e [ 1615.109211] RBP: 0000000000040010 R08: 0000000000000000 R09: 0000000000000016 [ 1615.109515] R10: 00000000000006a1 R11: 0000000000000246 R12: 0000000000041000 [ 1615.109806] R13: 0000000000040010 R14: 0000000000001000 R15: 0000000000002710 [ 1615.110152] ---[ end trace 96ed63b1306bf2f3 ]--- Fixes: a974deee ("NFSv4: Fix memory and state leak in...") Signed-off-by:
Kinglong Mee <kinglongmee@gmail.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Andy Shevchenko authored
commit 80354c29 upstream. The interrupt line used for the watchdog is 12, according to the official Intel Edison BSP code. And indeed after fixing it we start getting an interrupt and thus the watchdog starts working again: [ 191.699951] Kernel panic - not syncing: Kernel Watchdog Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: David Cohen <david.a.cohen@linux.intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 78a3bb9e ("x86: intel-mid: add watchdog platform code for Merrifield") Link: http://lkml.kernel.org/r/20170312150744.45493-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Edwin Chan authored
commit 89316fa3 upstream. Make sure clock is enabled for ethtool ops. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
Edwin Chan <edwin.chan@broadcom.com> Signed-off-by:
Doug Berger <opendmb@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Doug Berger authored
commit 6be371b0 upstream. When using the internal PHY it must be powered up when the MII is probed or the PHY will not be detected. Since the PHY is powered up at reset this has not been a problem. However, when the kernel is restarted with kexec the PHY will likely be powered down when the kernel starts so it will not be detected and the Ethernet link will not be established. This commit explicitly powers up the internal PHY when the GENET driver is probed to correct this behavior. Fixes: 1c1008c7 ("net: bcmgenet: add main driver file") Signed-off-by:
-
