Platform registration happens in probe work handler whereas machine
device is registered during skl_probe. This sometimes results in cpu
dais not found if the work handler is sufficiently delayed due to system
load, even with deferred probe of machine driver.

So move machine device registration after registering platform.
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Sometimes during boot, panic is observed at sst_dsp_shim_read_unlocked().
This happens when interrupt occurs before the context is initialized. So
move the irq initialization only after the context is initialized
completely.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Pawse, GuruprasadX <guruprasadx.pawse@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

I get a Smatch warning here:

    sound/soc/intel/skylake/skl-nhlt.c:335 skl_get_ssp_clks()
    error: testing array offset 'j' after use.

The code is harmless, but the checker is right that we should swap these
two conditions so we verify that the offset is within bounds before we
use it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

DSP clock source is configured by sending the A-State table to the FW.
Add the large config set IPC to configure the desired clock source
Signed-off-by: Pradeep Tewani <pradeep.d.tewani@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

A-State table is a power management table which allows the driver to
configure the DSP clock source corresponding to various load thresholds.
The table contains upto 3 A-State entries. The patch adds and parses the
corresponding A-State tokens to build the table.
Signed-off-by: Pradeep Tewani <pradeep.d.tewani@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

No need to read the register again if the value read has already matched
the target during the loop. So remove the second shim read.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rtd->codec will be removed soon.
rtd->codec = rtd->codec_dai->codec, thus,
we can use rtd->codec_dai->component instead of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

rtd->codec will be removed soon.
rtd->codec = rtd->codec_dai->codec, thus,
we can use rtd->codec_dai->component instead of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix a few incorrect descriptions for arguments in exported functions.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some functions are local to the source and do not need to be in global
scope, so make them static.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This laptop has actually two different analog mics, no just one. Fix the
quirk to reflect the correct configuration.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The RT5651 codec has 3 analog inputs. Some laptops have two different
internal analog microphones on the external case.
Add a new custom quirk mapping the two internal mics on IN1P / IN2P,
leaving the headset mic on IN3P.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When NHLT endpoint is present for a SSP then we create clock for that SSP.

MCLK is consistent across endpoints and configuration for an SSP, so query
only for first endpoint for an SSP.

For SCLK/SCLKFS, the best fit is queried from the NHLT configurations which
matches the clock rate requested. Best fit is decided based on below:

1. If rate matches with multiple configurations, then the first
   configuration is selected.

2. If for a selected fs and bits_per_sample, there are multiple endpoint
   configuration match, then the configuration with max number of
   channels is selected. So, the user has to set the rate which fits
   max number of channels

So we create a platform device and pass clock information parsed as
platform data.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Android 3.5mm Headset jack specification mentions that BTN_0 should
be mapped to KEY_MEDIA, but this is less logical than KEY_PLAYPAUSE,
which has much broader userspace support.

For example, the Chrome OS userspace now supports KEY_PLAYPAUSE to toggle
play/pause of videos and audio, but does not handle KEY_MEDIA.

Furthermore, Android itself now supports KEY_PLAYPAUSE equivalently, as the
new USB headset spec requires KEY_PLAYPAUSE for BTN_0.
https://source.android.com/devices/accessories/headset/usb-headset-specSigned-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

The Android 3.5mm Headset jack specification mentions that BTN_0 should
be mapped to KEY_MEDIA, but this is less logical than KEY_PLAYPAUSE,
which has much broader userspace support.

For example, the Chrome OS userspace now supports KEY_PLAYPAUSE to toggle
play/pause of videos and audio, but does not handle KEY_MEDIA.

Furthermore, Android itself now supports KEY_PLAYPAUSE equivalently, as the
new USB headset spec requires KEY_PLAYPAUSE for BTN_0.
https://source.android.com/devices/accessories/headset/usb-headset-specSigned-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

When CONFIG_SND_SOC_HDAC_HDMI is disabled, we can run into an
uninitialized variable:

sound/soc/intel/skylake/skl.c: In function 'skl_resume':
sound/soc/intel/skylake/skl.c:326:6: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]

I have run into this on today's linux-next kernel, but it appears
that this is an older problem that was just hard to trigger
with randconfig builds as CONFIG_SND_SOC_HDAC_HDMI would in
effect be impossible to disable when having SND_SOC_INTEL_SKYLAKE
enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The MODULE_DESCRIPTION() macro is only available when including
the linux/module.h header. Apparently this is included indirectly
from sst-firmware.c in some configurations, but not in others:

sound/soc/intel/common/sst-firmware.c:1278:20: error: expected declaration specifiers or '...' before string constant
 MODULE_DESCRIPTION("Intel SST Firmware Loader");
                    ^~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/soc/intel/common/sst-firmware.c:1279:16: error: expected declaration specifiers or '...' before string constant

This adds the missing include line.

Fixes: a395bdd6 ("ASoC: intel: Fix sst-dsp dependency on dw stuff")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

I ran into multiple problems during randconfig builds of the
recently changed Kconfig logic for Intel ASoC drivers:

- Building without DMADEVICES doesn't work in general
- With that dependency added, we can relax the 'depends
  on X86' again and allow compile-testing, except for
  SND_SST_ATOM_HIFI2_PLATFORM, which depends on X86
  for asm/platform_sst_audio.h
- Skylake requires SND_SOC_INTEL_SST_ACPI, so we
  have to depend on ACPI in turn
- Haswell needs SND_DMA_SGBUF for snd_sgbuf_aligned_pages()

With the new set of dependencies, I no longer get any build
failures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch sets the SSP params based on FE and BE dai links
for kabylake machine driver that uses rt5663 and max98927 codecs
Signed-off-by: Naveen M <naveen.m@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In this patch the SSP0 BE's mode is changed from I2S mode to DSP_B
with 8 slots of 16 bits. It enables 4 slot for IV feedback and 2 slots for
playback on max98927 for kabylake machine driver

The layout of SSP0 Tx and Rx slots is as follows;
1. Playback uses Tx slots 0 and 1
2. Capture uses Rx slots 4,5,6,7.

Slots 0 through 3 of Rx are used by DMIC codec RT5514 in another flavor
of Kabylake platform. We are using the same slots 4 through 7 on all
Kabylake platforms for max98927 in order to reuse same NHLT configuration.
Signed-off-by: Naveen M <naveen.m@intel.com>
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This cherry-trails laptop has the internal mic connected to the IN2
input pins. Enable the quirk to correctly map the routes.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Introduce an headset jack in the machine driver and register it to the
codec driver.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In case of failure in loading customize topology firmware, dfw_sst.bin
gets loaded. However, current log provides this message as error even
after successfully falling back to default topology "dfw_sst.bin".

Hence to convey proper message, changing log level and message.
Signed-off-by: Chintan Patel <chintan.m.patel@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Make all Intel audio drivers dependent on X86 to avoid compilation
errors for s390 and xtensa architectures.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Introduce more logical dependencies, with the SOC selected first and the
relevant machine drivers are exposed.
The same mechanism will be used for SOF support.

Also select SND_SOC_ACPI_INTEL_MATCH for all machine drivers
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This file is a mess, order by generation with more recent last
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

split Kconfig to prepare for reuse of machine drivers for
SOF support
no functional change or edits
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Prepare for SOF integration, no functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

First step of cleaning, move all tables to soc-acpi-intel-match module.
The tables remain in separate files per platform to keep them
manageable. Skylake+ platforms are still handled elsewhere since
there is no conflict with SOF for now, but this will have to be
handled at a later point.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To prepare for SOF integration, we need new fields in the machine table.
It is intended that the same table is used for both closed-source and
open-source firmware to avoid repeating ACPI-related information
multiple times
No functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Before we add new fields for SOF support, move to C99 syntax
as done for atom/sst and legacy hsw/bdw code
No functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ACPI support is not specific to the Intel/SST driver. Move the enumeration
and matching code which is not hardware-dependent to sound/soc and rename
relevant sst_acpi_ structures and functions with snd_soc_acpi_ prefix

soc-acpi.h is protected by a #ifndef __LINUX_SND_SOC_ACPI_H for
consistency with all other SoC .h files:

grep -L __LINUX include/sound/soc* | wc -l
0
grep __LINUX include/sound/soc* | wc -l
14
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Introduce a new custom dapm routes map to quirk platforms with the
internal mic connected to IN2P.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The pointer dma_dev_name is assigned but never read, it is redundant
and can therefore be removed.

Cleans up clang warning:
sound/soc/intel/common/sst-firmware.c:288:3: warning: Value stored to
'dma_dev_name' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The hard-coded compressed dailinks are not supported using
publicly-available firmwares, which creates unnecessary user
confusion [1]. Even if the firmware was available, the mainline
code does not have the required .dynamic=1 and .dpcm_playback=1
fields so probably never worked as is, and last and they conflict
with topology-defined streams.

Remove them and move on. This can be re-enabled with SOF later
in a more flexible manner.

[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2017-August/124868.htmlSigned-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

For some reason the Atom/HiFi2 machine drivers use an id=1 instead
of zero as done on all other platforms. This gets in the way of
topology-based matching, realign for consistency. This should
not have any functional impact on existing solutions with don't rely
on topology.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove duplicate code with a common helper in all Intel machine drivers.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

get_codec_dai() is not used, remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>