Commits · 75edf81d337ea84a291f0fdae2777cfd07045eca · Kirill Smelkov / linux

08 May, 2007 7 commits

[SCSI] qla2xxx: Attempt to stop firmware only if it had been previously executed. · 75edf81d
Andrew Vasquez authored May 07, 2007
```
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
```
75edf81d

[SCSI] qla2xxx: Honor NVRAM port-down-retry-count settings. · a7b61842

Andrew Vasquez authored May 07, 2007

Hardcoding the qlport_down_retry module-parameter
effectively disallowed any user-defined NVRAM setting to go
into effect.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

a7b61842

[SCSI] qla2xxx: Error-out during probe() if we're unable to complete HBA initialization. · 765140bf

Andrew Vasquez authored May 07, 2007

Remove a stale check against ha->device_flags
(DFLG_NO_CABLE) as topology scanning is performed within the
DPC-thread context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

765140bf

[SCSI] zfcp: Stop system after memory corruption · b03670e5

Christof Schmitt authored May 07, 2007

For each request that is sent to the FCP adapter, zfcp allocates
memory. Status information and data that is being read from the
device is written to this memory by the hardware. After that,
the hardware signals this via the response queue and zfcp
continues processing.

Now, if zfcp detects that there is a signal for an incoming
response from the hardware, but there is no outstanding request
for that request id, then some memory that can be in use anywhere
in the system has just been overwritten. This should never happen,
but if it does, stop the system with a panic.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

b03670e5

[SCSI] mesh: cleanup variable usage in interrupt handler · 2135be5f

Olaf Hering authored Apr 26, 2007

_ convert void* to struct mesh_state*

- remove unused irq argument from mesh_interrupt()
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

2135be5f

[SCSI] megaraid: replace yield() with cond_resched() · e1fa0cea

Amol Lad authored Apr 26, 2007

For this driver cond_resched() seems to be a better alternative
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

e1fa0cea

[SCSI] megaraid: fix warnings when CONFIG_PROC_FS=n · 84a3c97b

walter harms authored Apr 26, 2007

drivers/scsi/megaraid.c: In function 'megaraid_probe_one':
drivers/scsi/megaraid.c:4893: warning: implicit declaration of function 'mega_create_proc_entry'
drivers/scsi/megaraid.c: In function 'megaraid_remove_one':
drivers/scsi/megaraid.c:4968: warning: unused variable 'buf'

Fix by adding #defines
Signed-off-by: walter harms <wharms@bfs.de>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

84a3c97b

06 May, 2007 33 commits

[SCSI] aacraid: correct SUN products to README · 39580f2c

Salyzyn, Mark authored May 03, 2007

Correct SUN products in aacraid documentation, preliminary names were
changed from internal project to customer product prior to release.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

39580f2c

[SCSI] aacraid: superfluous adapter reset for IBM 8 series ServeRAID controllers · 9e4d4a5d

Salyzyn, Mark authored May 01, 2007

The kexec patch introduced a superfluous (and otherwise inert) reset of
some adapters. The register can have a hardware default value that has
zeros for the undefined interrupts. This patch refines the test of the
interrupt enable register to focus on only the interrupts that affect
the driver in order to detect if an incomplete shutdown of the Adapter
had occurred (kdump).
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

9e4d4a5d

[SCSI] aacraid: kexec fix (reset interrupt handler) · a5694ec5

Salyzyn, Mark authored Apr 30, 2007

Another layer on this onion also discovered by Duane, the
interrupt enable handler also needed to be set ... The interrupt enable
was called from within the synchronous command handler.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

a5694ec5

[SCSI] tmscsim: Remove the last bus_to_virt() · 85923211

Guennadi Liakhovetski authored May 04, 2007

Dynamically map the buffer for PIO for the residue byte.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

85923211

[SCSI] tmscsim: remove bogus endianness conversions · 46e5ba2b

Guennadi Liakhovetski authored May 04, 2007

cpu_to_le32 endianness conversions in tmscsim.c, followed by
arithmetic operations don't look correct. Besides, {in,out}[wl]
already perform the necessary conversions. Further, bus addresses
of request buffers are guaranteed to be (mapped) under 4G by
current scsi- and block-layer defaults. This could be explicitly
enforced by using blk_queue_bounce_limit(), which, however,
doesn't seem to be the common practice among SCSI drivers.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

46e5ba2b

[SCSI] tmscsim: remove long dead DMA_INT · 860bfecf

Guennadi Liakhovetski authored May 04, 2007

DMA_INT code is disabled since 1998, remove it to prepare
for further cleanup.
Signed-off-by: G. Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

860bfecf

[SCSI] ipr: Better handle adapter boot time errors · 473b1e8e

Brian King authored May 02, 2007

If an ipr adapter encounters an adapter error requiring an
adapter reset to recover from prior to driver load time, the
error will be ignored and recovery will not happen until the
initial timeout occurs waiting for the firmware to come ready,
which means a five minute timeout. Fix is to read the interrupt
register before clearing any of the interrupts at probe time.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

473b1e8e

[SCSI] deprecate the old NCR53C9x driver · a6bcbc2f

Christoph Hellwig authored Apr 30, 2007

Now that we have the much better esp_scsi driver and low level drivers
are easy to port over deprecate the old NCR53C9x driver.

I've Cc'ed the m68k and mips lists because all but one bus glues are
for these platforms. Chances stand bad for the remaining driver,
mca_53c9x which hasn't gotten any non-trivial update since it was
merge in late 2.1.x and whos maintainers mail address bounces.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

a6bcbc2f

[SCSI] fc_transport: make all rports wait dev_loss_tmo before removing them · 92740b24

James Smart authored Apr 27, 2007

Per the comment in the change - it's not always prudent to immediately
remove the rport upon first notice of a disconnect. Make all rports
wait dev_loss_tmo before being deleted (and each could have a separate
dev_loss_tmo value).

The original post was:
http://marc.info/?l=linux-scsi&m=117392196006703&w=2

The repost contains the following changes:
 - Bug fix in fc_starget_delete(). Dev_loss_tmo_callbk() was called prior to
   tearing down the target. The callback is to be the last thing called, as
   it tells the LLDD that the rport is completely finished and can be torn
   down.  Rework so that terminate_rport_io() is called to terminate the
   outstanding io. Isolated work so it's is simply "starget" work.
 - Fix holes in original patch. There were code paths that did not expect
   the dev_loss_tmo timer to be running for the non-fcp rports.
 - Bug Fix: the transport wasn't protecting against a LLDD calling
   fc_remote_port_delete() back-to-back. Thus, the dev_loss_tmo timer
   could be restarted such that it fires after the rport had been deleted.
   Validate rport state before starting the timer.
Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>