Recently all usage of setup_irq() was replaced by request_irq(). The
replacement in timer-vf-pit.c missed closing parentheses resulting in a build
error (vf610m4_defconfig). Fix it.

Fixes: cc2550b4 ("clocksource: Replace setup_irq() by request_irq()")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200323061130.GA6286@afzalpc

A hrtimer can be released in its callback, but lockdep_hrtimer_exit()
dereferences the pointer after the callback returns, i.e. a potential use
after free.

Retrieve the context in which the hrtimer expires before the callback is
invoked and use it in lockdep_hrtimer_exit().

Fixes: 40db1739 ("lockdep: Add hrtimer context tracing bits")
Reported-by: syzbot+62c155c276e580cfb606@syzkaller.appspotmail.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200331201849.fkp2siy3vcdqvqlz@linutronix.de

Pull x86 vmware updates from Ingo Molnar:
 "The main change in this tree is the addition of 'steal time clock
  support' for VMware guests"

* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vmware: Use bool type for vmw_sched_clock
  x86/vmware: Enable steal time accounting
  x86/vmware: Add steal time clock support for VMware guests
  x86/vmware: Remove vmware_sched_clock_setup()
  x86/vmware: Make vmware_select_hypercall() __init

Pull x86 mm updates from Ingo Molnar:
 "A handful of changes:

   - two memory encryption related fixes

   - don't display the kernel's virtual memory layout plaintext on
     32-bit kernels either

   - two simplifications"

* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Remove the now redundant N_MEMORY check
  dma-mapping: Fix dma_pgprot() for unencrypted coherent pages
  x86: Don't let pgprot_modify() change the page encryption bit
  x86/mm/kmmio: Use this_cpu_ptr() instead get_cpu_var() for kmmio_ctx
  x86/mm/init/32: Stop printing the virtual memory layout

Pull misc x86 updates from Ingo Molnar:

 - extend the decoder maps with CET instructions

 - fix !vDSO corner cases

* 'x86-misc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/tests: Add CET instructions to the new instructions test
  x86/insn: Add Control-flow Enforcement (CET) instructions to the opcode map
  selftests/x86/ptrace_syscall_32: Fix no-vDSO segfault
  selftests/x86/vdso: Fix no-vDSO segfaults

Pull x86 fpu updates from Ingo Molnar:
 "Misc changes:

   - add a pkey sanity check

   - three commits to improve and future-proof xstate/xfeature handling
     some more"

* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pkeys: Add check for pkey "overflow"
  x86/fpu/xstate: Warn when checking alignment of disabled xfeatures
  x86/fpu/xstate: Fix XSAVES offsets in setup_xstate_comp()
  x86/fpu/xstate: Fix last_good_offset in setup_xstate_features()

Pull x86 cleanups from Ingo Molnar:
 "This topic tree contains more commits than usual:

   - most of it are uaccess cleanups/reorganization by Al

   - there's a bunch of prototype declaration (--Wmissing-prototypes)
     cleanups

   - misc other cleanups all around the map"

* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  x86/mm/set_memory: Fix -Wmissing-prototypes warnings
  x86/efi: Add a prototype for efi_arch_mem_reserve()
  x86/mm: Mark setup_emu2phys_nid() static
  x86/jump_label: Move 'inline' keyword placement
  x86/platform/uv: Add a missing prototype for uv_bau_message_interrupt()
  kill uaccess_try()
  x86: unsafe_put-style macro for sigmask
  x86: x32_setup_rt_frame(): consolidate uaccess areas
  x86: __setup_rt_frame(): consolidate uaccess areas
  x86: __setup_frame(): consolidate uaccess areas
  x86: setup_sigcontext(): list user_access_{begin,end}() into callers
  x86: get rid of put_user_try in __setup_rt_frame() (both 32bit and 64bit)
  x86: ia32_setup_rt_frame(): consolidate uaccess areas
  x86: ia32_setup_frame(): consolidate uaccess areas
  x86: ia32_setup_sigcontext(): lift user_access_{begin,end}() into the callers
  x86/alternatives: Mark text_poke_loc_init() static
  x86/cpu: Fix a -Wmissing-prototypes warning for init_ia32_feat_ctl()
  x86/mm: Drop pud_mknotpresent()
  x86: Replace setup_irq() by request_irq()
  x86/configs: Slightly reduce defconfigs
  ...

Pull x86 build updates from Ingo Molnar:
 "A handful of updates: two linker script cleanups and a stock
  defconfig+allmodconfig bootability fix"

* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vdso: Discard .note.gnu.property sections in vDSO
  x86, vmlinux.lds: Add RUNTIME_DISCARD_EXIT to generic DISCARDS
  x86/Kconfig: Make CMDLINE_OVERRIDE depend on non-empty CMDLINE

Pull x86 boot updates from Ingo Molnar:
 "Misc cleanups and small enhancements all around the map"

* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/compressed: Fix debug_puthex() parameter type
  x86/setup: Fix static memory detection
  x86/vmlinux: Drop unneeded linker script discard of .eh_frame
  x86/*/Makefile: Use -fno-asynchronous-unwind-tables to suppress .eh_frame sections
  x86/boot/compressed: Remove .eh_frame section from bzImage
  x86/boot/compressed/64: Remove .bss/.pgtable from bzImage
  x86/boot/compressed/64: Use 32-bit (zero-extended) MOV for z_output_len
  x86/boot/compressed/64: Use LEA to initialize boot stack pointer

Pull arm64 updates from Catalin Marinas:
 "The bulk is in-kernel pointer authentication, activity monitors and
  lots of asm symbol annotations. I also queued the sys_mremap() patch
  commenting the asymmetry in the address untagging.

  Summary:

   - In-kernel Pointer Authentication support (previously only offered
     to user space).

   - ARM Activity Monitors (AMU) extension support allowing better CPU
     utilisation numbers for the scheduler (frequency invariance).

   - Memory hot-remove support for arm64.

   - Lots of asm annotations (SYM_*) in preparation for the in-kernel
     Branch Target Identification (BTI) support.

   - arm64 perf updates: ARMv8.5-PMU 64-bit counters, refactoring the
     PMU init callbacks, support for new DT compatibles.

   - IPv6 header checksum optimisation.

   - Fixes: SDEI (software delegated exception interface) double-lock on
     hibernate with shared events.

   - Minor clean-ups and refactoring: cpu_ops accessor,
     cpu_do_switch_mm() converted to C, cpufeature finalisation helper.

   - sys_mremap() comment explaining the asymmetric address untagging
     behaviour"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (81 commits)
  mm/mremap: Add comment explaining the untagging behaviour of mremap()
  arm64: head: Convert install_el2_stub to SYM_INNER_LABEL
  arm64: Introduce get_cpu_ops() helper function
  arm64: Rename cpu_read_ops() to init_cpu_ops()
  arm64: Declare ACPI parking protocol CPU operation if needed
  arm64: move kimage_vaddr to .rodata
  arm64: use mov_q instead of literal ldr
  arm64: Kconfig: verify binutils support for ARM64_PTR_AUTH
  lkdtm: arm64: test kernel pointer authentication
  arm64: compile the kernel with ptrauth return address signing
  kconfig: Add support for 'as-option'
  arm64: suspend: restore the kernel ptrauth keys
  arm64: __show_regs: strip PAC from lr in printk
  arm64: unwind: strip PAC from kernel addresses
  arm64: mask PAC bits of __builtin_return_address
  arm64: initialize ptrauth keys for kernel booting task
  arm64: initialize and switch ptrauth kernel keys
  arm64: enable ptrauth earlier
  arm64: cpufeature: handle conflicts based on capability
  arm64: cpufeature: Move cpu capability helpers inside C file
  ...

Pull microblaze updates from Michal Simek:

 - convert license headers to SPDX

 - cleanup header handling and use asm-generic one

 - get rid of earlyprintk residues

 - define barriers and use it in the code

 - get rid of setup_irq() for timer

 - various small addons and fixes

* tag 'microblaze-v5.7-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Replace setup_irq() by request_irq()
  microblaze: Stop printing the virtual memory layout
  microblaze: Use asm generic cmpxchg.h for !SMP case
  microblaze: Define percpu sestion in linker file
  microblaze: Remove unused boot_cpuid variable
  microblaze: Add missing irqflags.h header
  microblaze: Add sync to tlb operations
  microblaze: Define microblaze barrier
  microblaze: Remove empty headers
  microblaze: Remove early printk setup
  microblaze: Remove architecture tlb.h and use generic one
  microblaze: Convert headers to SPDX license
  microblaze: Fix _reset() function
  microblaze: Kernel parameters should be parsed earlier

Pull ia64 updates from Tony Luck:
 "Couple of cleanup patches"

* tag 'please-pull-ia64_for_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  tty/serial: cleanup after ioc*_serial driver removal
  ia64: replace setup_irq() by request_irq()

Pull MIPS updates from Thomas Bogendoerfer:

 - loongson64 irq rework

 - dmi support loongson

 - replace setup_irq() by request_irq()

 - jazz cleanups

 - minor cleanups and fixes

* tag 'mips_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (44 commits)
  MIPS: ralink: mt7621: Fix soc_device introduction
  MIPS: Exclude more dsemul code when CONFIG_MIPS_FP_SUPPORT=n
  MIPS/tlbex: Fix LDDIR usage in setup_pw() for Loongson-3
  MIPS: do not compile generic functions for CONFIG_CAVIUM_OCTEON_SOC
  MAINTAINERS: Update Loongson64 entry
  MIPS: Loongson64: Load built-in dtbs
  MIPS: Loongson64: Add generic dts
  dt-bindings: mips: Add loongson boards
  MIPS: Loongson64: Drop legacy IRQ code
  dt-bindings: interrupt-controller: Add Loongson-3 HTPIC
  irqchip: Add driver for Loongson-3 HyperTransport PIC controller
  dt-bindings: interrupt-controller: Add Loongson LIOINTC
  irqchip: loongson-liointc: Workaround LPC IRQ Errata
  irqchip: Add driver for Loongson I/O Local Interrupt Controller
  docs: mips: remove no longer needed au1xxx_ide.rst documentation
  MIPS: Alchemy: remove no longer used au1xxx_ide.h header
  ide: remove no longer used au1xxx-ide driver
  MIPS: Add support for Desktop Management Interface (DMI)
  firmware: dmi: Add macro SMBIOS_ENTRY_POINT_SCAN_START
  MIPS: ralink: mt7621: introduce 'soc_device' initialization
  ...

Pull m68k updates from Geert Uytterhoeven:

 - pagetable layout rewrite, to facilitate global READ_ONCE() rework

 - Zorro (Amiga) and DIO (HP 9000/300) bus cleanups

 - defconfig updates

 - minor cleanups and fixes

* tag 'm68k-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (23 commits)
  m68k: defconfig: Update defconfigs for v5.6-rc4
  zorro: Replace zero-length array with flexible-array member
  m68k: Switch to asm-generic/hardirq.h
  fbdev: c2p: Use BUILD_BUG() instead of custom solution
  dio: Remove unused dio_dev_driver()
  dio: Fix dio_bus_match() kerneldoc
  dio: Make dio_match_device() static
  zorro: Move zorro_bus_type to bus-private header file
  zorro: Remove unused zorro_dev_driver()
  zorro: Use zorro_match_device() helper in zorro_bus_match()
  zorro: Fix zorro_bus_match() kerneldoc
  zorro: Make zorro_match_device() static
  m68k: Fix Kconfig indentation
  m68k: mm: Change ColdFire pgtable_t
  m68k: mm: Fully initialize the page-table allocator
  m68k: mm: Extend table allocator for multiple sizes
  m68k: mm: Use table allocator for pgtables
  m68k: mm: Improve kernel_page_table()
  m68k: mm: Restructure Motorola MMU page-table layout
  m68k: mm: Move the pointer table allocator to motorola.c
  ...

Pull x86 timer updates from Thomas Gleixner:
 "A series of commits to make the MSR derived CPU and TSC frequency more
  accurate.

  It turned out that the frequency tables which have been taken from the
  SDM are inaccurate because the SDM provides truncated and rounded
  values, e.g. 83.3Mhz (83.3333...) or 116.7Mhz (116.6666...).

  This causes time drift in the range of ~1 second per hour (20-30
  seconds per day). On some of these SoCs it's not possible to
  recalibrate the TSC because there is no reference (PIT, HPET)
  available.

  With some reverse engineering it was established that the possible
  frequencies are derived from the base clock with fixed multiplier /
  divider pairs.

  For the CPU models which have a known crystal frequency the kernel now
  uses multiplier / divider pairs which bring the frequencies closer to
  reality and fix the observed time drift issues"

* tag 'x86-timers-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsc_msr: Make MSR derived TSC frequency more accurate
  x86/tsc_msr: Fix MSR_FSB_FREQ mask for Cherry Trail devices
  x86/tsc_msr: Use named struct initializers

Pull x86 splitlock updates from Thomas Gleixner:
 "Support for 'split lock' detection:

  Atomic operations (lock prefixed instructions) which span two cache
  lines have to acquire the global bus lock. This is at least 1k cycles
  slower than an atomic operation within a cache line and disrupts
  performance on other cores. Aside of performance disruption this is a
  unpriviledged form of DoS.

  Some newer CPUs have the capability to raise an #AC trap when such an
  operation is attempted. The detection is by default enabled in warning
  mode which will warn once when a user space application is caught. A
  command line option allows to disable the detection or to select fatal
  mode which will terminate offending applications with SIGBUS"

* tag 'x86-splitlock-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/split_lock: Avoid runtime reads of the TEST_CTRL MSR
  x86/split_lock: Rework the initialization flow of split lock detection
  x86/split_lock: Enable split lock detection by kernel

Pull x86 entry code updates from Thomas Gleixner:

 - Convert the 32bit syscalls to be pt_regs based which removes the
   requirement to push all 6 potential arguments onto the stack and
   consolidates the interface with the 64bit variant

 - The first small portion of the exception and syscall related entry
   code consolidation which aims to address the recently discovered
   issues vs. RCU, int3, NMI and some other exceptions which can
   interrupt any context. The bulk of the changes is still work in
   progress and aimed for 5.8.

 - A few lockdep namespace cleanups which have been applied into this
   branch to keep the prerequisites for the ongoing work confined.

* tag 'x86-entry-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
  x86/entry: Fix build error x86 with !CONFIG_POSIX_TIMERS
  lockdep: Rename trace_{hard,soft}{irq_context,irqs_enabled}()
  lockdep: Rename trace_softirqs_{on,off}()
  lockdep: Rename trace_hardirq_{enter,exit}()
  x86/entry: Rename ___preempt_schedule
  x86: Remove unneeded includes
  x86/entry: Drop asmlinkage from syscalls
  x86/entry/32: Enable pt_regs based syscalls
  x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments
  x86/entry/32: Rename 32-bit specific syscalls
  x86/entry/32: Clean up syscall_32.tbl
  x86/entry: Remove ABI prefixes from functions in syscall tables
  x86/entry/64: Add __SYSCALL_COMMON()
  x86/entry: Remove syscall qualifier support
  x86/entry/64: Remove ptregs qualifier from syscall table
  x86/entry: Move max syscall number calculation to syscallhdr.sh
  x86/entry/64: Split X32 syscall table into its own file
  x86/entry/64: Move sys_ni_syscall stub to common.c
  x86/entry/64: Use syscall wrappers for x32_rt_sigreturn
  x86/entry: Refactor SYS_NI macros
  ...

Pull timekeeping and timer updates from Thomas Gleixner:
 "Core:

   - Consolidation of the vDSO build infrastructure to address the
     difficulties of cross-builds for ARM64 compat vDSO libraries by
     restricting the exposure of header content to the vDSO build.

     This is achieved by splitting out header content into separate
     headers. which contain only the minimaly required information which
     is necessary to build the vDSO. These new headers are included from
     the kernel headers and the vDSO specific files.

   - Enhancements to the generic vDSO library allowing more fine grained
     control over the compiled in code, further reducing architecture
     specific storage and preparing for adopting the generic library by
     PPC.

   - Cleanup and consolidation of the exit related code in posix CPU
     timers.

   - Small cleanups and enhancements here and there

  Drivers:

   - The obligatory new drivers: Ingenic JZ47xx and X1000 TCU support

   - Correct the clock rate of PIT64b global clock

   - setup_irq() cleanup

   - Preparation for PWM and suspend support for the TI DM timer

   - Expand the fttmr010 driver to support ast2600 systems

   - The usual small fixes, enhancements and cleanups all over the
     place"

* tag 'timers-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (80 commits)
  Revert "clocksource/drivers/timer-probe: Avoid creating dead devices"
  vdso: Fix clocksource.h macro detection
  um: Fix header inclusion
  arm64: vdso32: Enable Clang Compilation
  lib/vdso: Enable common headers
  arm: vdso: Enable arm to use common headers
  x86/vdso: Enable x86 to use common headers
  mips: vdso: Enable mips to use common headers
  arm64: vdso32: Include common headers in the vdso library
  arm64: vdso: Include common headers in the vdso library
  arm64: Introduce asm/vdso/processor.h
  arm64: vdso32: Code clean up
  linux/elfnote.h: Replace elf.h with UAPI equivalent
  scripts: Fix the inclusion order in modpost
  common: Introduce processor.h
  linux/ktime.h: Extract common header for vDSO
  linux/jiffies.h: Extract common header for vDSO
  linux/time64.h: Extract common header for vDSO
  linux/time32.h: Extract common header for vDSO
  linux/time.h: Extract common header for vDSO
  ...

Pull NOHZ update from Thomas Gleixner:
 "Remove TIF_NOHZ from three architectures

  These architectures use a static key to decide whether context
  tracking needs to be invoked and the TIF_NOHZ flag just causes a
  pointless slowpath execution for nothing"

* tag 'timers-nohz-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  arm64: Remove TIF_NOHZ
  arm: Remove TIF_NOHZ
  x86: Remove TIF_NOHZ
  context-tracking: Introduce CONFIG_HAVE_TIF_NOHZ
  x86/entry: Remove _TIF_NOHZ from _TIF_WORK_SYSCALL_ENTRY

Pull core SMP updates from Thomas Gleixner:
 "CPU (hotplug) updates:

   - Support for locked CSD objects in smp_call_function_single_async()
     which allows to simplify callsites in the scheduler core and MIPS

   - Treewide consolidation of CPU hotplug functions which ensures the
     consistency between the sysfs interface and kernel state. The low
     level functions cpu_up/down() are now confined to the core code and
     not longer accessible from random code"

* tag 'smp-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
  cpu/hotplug: Ignore pm_wakeup_pending() for disable_nonboot_cpus()
  cpu/hotplug: Hide cpu_up/down()
  cpu/hotplug: Move bringup of secondary CPUs out of smp_init()
  torture: Replace cpu_up/down() with add/remove_cpu()
  firmware: psci: Replace cpu_up/down() with add/remove_cpu()
  xen/cpuhotplug: Replace cpu_up/down() with device_online/offline()
  parisc: Replace cpu_up/down() with add/remove_cpu()
  sparc: Replace cpu_up/down() with add/remove_cpu()
  powerpc: Replace cpu_up/down() with add/remove_cpu()
  x86/smp: Replace cpu_up/down() with add/remove_cpu()
  arm64: hibernate: Use bringup_hibernate_cpu()
  cpu/hotplug: Provide bringup_hibernate_cpu()
  arm64: Use reboot_cpu instead of hardconding it to 0
  arm64: Don't use disable_nonboot_cpus()
  ARM: Use reboot_cpu instead of hardcoding it to 0
  ARM: Don't use disable_nonboot_cpus()
  ia64: Replace cpu_down() with smp_shutdown_nonboot_cpus()
  cpu/hotplug: Create a new function to shutdown nonboot cpus
  cpu/hotplug: Add new {add,remove}_cpu() functions
  sched/core: Remove rq.hrtick_csd_pending
  ...

Pull irq updates from Thomas Gleixner:
 "Updates for the interrupt subsystem:

  Treewide:

    - Cleanup of setup_irq() which is not longer required because the
      memory allocator is available early.

      Most cleanup changes come through the various maintainer trees, so
      the final removal of setup_irq() is postponed towards the end of
      the merge window.

  Core:

    - Protection against unsafe invocation of interrupt handlers and
      unsafe interrupt injection including a fixup of the offending
      PCI/AER error injection mechanism.

      Invoking interrupt handlers from arbitrary contexts, i.e. outside
      of an actual interrupt, can cause inconsistent state on the
      fragile x86 interrupt affinity changing hardware trainwreck.

  Drivers:

    - Second wave of support for the new ARM GICv4.1

    - Multi-instance support for Xilinx and PLIC interrupt controllers

    - CPU-Hotplug support for PLIC

    - The obligatory new driver for X1000 TCU

    - Enhancements, cleanups and fixes all over the place"

* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
  unicore32: Replace setup_irq() by request_irq()
  sh: Replace setup_irq() by request_irq()
  hexagon: Replace setup_irq() by request_irq()
  c6x: Replace setup_irq() by request_irq()
  alpha: Replace setup_irq() by request_irq()
  irqchip/gic-v4.1: Eagerly vmap vPEs
  irqchip/gic-v4.1: Add VSGI property setup
  irqchip/gic-v4.1: Add VSGI allocation/teardown
  irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
  irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
  irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
  irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
  irqchip/gic-v4.1: Add initial SGI configuration
  irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
  irqchip/stm32: Retrigger both in eoi and unmask callbacks
  irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
  irqchip/xilinx: Do not call irq_set_default_host()
  irqchip/xilinx: Enable generic irq multi handler
  irqchip/xilinx: Fill error code when irq domain registration fails
  irqchip/xilinx: Add support for multiple instances
  ...

There's a semantic conflict in the Octeon staging network driver, which
used the skb_reset_tc() function to reset skb state when re-using an
skb.  But that inline helper function was removed in mainline by commit
2c64605b ("net: Fix CONFIG_NET_CLS_ACT=n and
CONFIG_NFT_FWD_NETDEV={y, m} build").

Fix it by using skb_reset_redirect() instead.  Also move it out of the

This code path only ends up triggering if REUSE_SKBUFFS_WITHOUT_FREE is
enabled, which in turn only happens if you don't have CONFIG_NETFILTER
configured.  Which was how this wasn't caught by the usual allmodconfig
builds.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull scheduler updates from Ingo Molnar:
 "The main changes in this cycle are:

   - Various NUMA scheduling updates: harmonize the load-balancer and
     NUMA placement logic to not work against each other. The intended
     result is better locality, better utilization and fewer migrations.

   - Introduce Thermal Pressure tracking and optimizations, to improve
     task placement on thermally overloaded systems.

   - Implement frequency invariant scheduler accounting on (some) x86
     CPUs. This is done by observing and sampling the 'recent' CPU
     frequency average at ~tick boundaries. The CPU provides this data
     via the APERF/MPERF MSRs. This hopefully makes our capacity
     estimates more precise and keeps tasks on the same CPU better even
     if it might seem overloaded at a lower momentary frequency. (As
     usual, turbo mode is a complication that we resolve by observing
     the maximum frequency and renormalizing to it.)

   - Add asymmetric CPU capacity wakeup scan to improve capacity
     utilization on asymmetric topologies. (big.LITTLE systems)

   - PSI fixes and optimizations.

   - RT scheduling capacity awareness fixes & improvements.

   - Optimize the CONFIG_RT_GROUP_SCHED constraints code.

   - Misc fixes, cleanups and optimizations - see the changelog for
     details"

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
  threads: Update PID limit comment according to futex UAPI change
  sched/fair: Fix condition of avg_load calculation
  sched/rt: cpupri_find: Trigger a full search as fallback
  kthread: Do not preempt current task if it is going to call schedule()
  sched/fair: Improve spreading of utilization
  sched: Avoid scale real weight down to zero
  psi: Move PF_MEMSTALL out of task->flags
  MAINTAINERS: Add maintenance information for psi
  psi: Optimize switching tasks inside shared cgroups
  psi: Fix cpu.pressure for cpu.max and competing cgroups
  sched/core: Distribute tasks within affinity masks
  sched/fair: Fix enqueue_task_fair warning
  thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code
  sched/rt: Remove unnecessary push for unfit tasks
  sched/rt: Allow pulling unfitting task
  sched/rt: Optimize cpupri_find() on non-heterogenous systems
  sched/rt: Re-instate old behavior in select_task_rq_rt()
  sched/rt: cpupri_find: Implement fallback mechanism for !fit case
  sched/fair: Fix reordering of enqueue/dequeue_task_fair()
  sched/fair: Fix runnable_avg for throttled cfs
  ...

Pull perf updates from Ingo Molnar:
 "The main changes in this cycle were:

  Kernel side changes:

   - A couple of x86/cpu cleanups and changes were grandfathered in due
     to patch dependencies. These clean up the set of CPU model/family
     matching macros with a consistent namespace and C99 initializer
     style.

   - A bunch of updates to various low level PMU drivers:
       * AMD Family 19h L3 uncore PMU
       * Intel Tiger Lake uncore support
       * misc fixes to LBR TOS sampling

   - optprobe fixes

   - perf/cgroup: optimize cgroup event sched-in processing

   - misc cleanups and fixes

  Tooling side changes are to:

   - perf {annotate,expr,record,report,stat,test}

   - perl scripting

   - libapi, libperf and libtraceevent

   - vendor events on Intel and S390, ARM cs-etm

   - Intel PT updates

   - Documentation changes and updates to core facilities

   - misc cleanups, fixes and other enhancements"

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
  cpufreq/intel_pstate: Fix wrong macro conversion
  x86/cpu: Cleanup the now unused CPU match macros
  hwrng: via_rng: Convert to new X86 CPU match macros
  crypto: Convert to new CPU match macros
  ASoC: Intel: Convert to new X86 CPU match macros
  powercap/intel_rapl: Convert to new X86 CPU match macros
  PCI: intel-mid: Convert to new X86 CPU match macros
  mmc: sdhci-acpi: Convert to new X86 CPU match macros
  intel_idle: Convert to new X86 CPU match macros
  extcon: axp288: Convert to new X86 CPU match macros
  thermal: Convert to new X86 CPU match macros
  hwmon: Convert to new X86 CPU match macros
  platform/x86: Convert to new CPU match macros
  EDAC: Convert to new X86 CPU match macros
  cpufreq: Convert to new X86 CPU match macros
  ACPI: Convert to new X86 CPU match macros
  x86/platform: Convert to new CPU match macros
  x86/kernel: Convert to new CPU match macros
  x86/kvm: Convert to new CPU match macros
  x86/perf/events: Convert to new CPU match macros
  ...

Pull locking updates from Ingo Molnar:
 "The main changes in this cycle were:

   - Continued user-access cleanups in the futex code.

   - percpu-rwsem rewrite that uses its own waitqueue and atomic_t
     instead of an embedded rwsem. This addresses a couple of
     weaknesses, but the primary motivation was complications on the -rt
     kernel.

   - Introduce raw lock nesting detection on lockdep
     (CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
     lock differences. This too originates from -rt.

   - Reuse lockdep zapped chain_hlocks entries, to conserve RAM
     footprint on distro-ish kernels running into the "BUG:
     MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
     chain-entries pool.

   - Misc cleanups, smaller fixes and enhancements - see the changelog
     for details"

* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
  fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
  thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
  Documentation/locking/locktypes: Minor copy editor fixes
  Documentation/locking/locktypes: Further clarifications and wordsmithing
  m68knommu: Remove mm.h include from uaccess_no.h
  x86: get rid of user_atomic_cmpxchg_inatomic()
  generic arch_futex_atomic_op_inuser() doesn't need access_ok()
  x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
  x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
  objtool: whitelist __sanitizer_cov_trace_switch()
  [parisc, s390, sparc64] no need for access_ok() in futex handling
  sh: no need of access_ok() in arch_futex_atomic_op_inuser()
  futex: arch_futex_atomic_op_inuser() calling conventions change
  completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
  lockdep: Add posixtimer context tracing bits
  lockdep: Annotate irq_work
  lockdep: Add hrtimer context tracing bits
  lockdep: Introduce wait-type checks
  completion: Use simple wait queues
  sched/swait: Prepare usage in completions
  ...

Pull EFI updates from Ingo Molnar:
 "The EFI changes in this cycle are much larger than usual, for two
  (positive) reasons:

   - The GRUB project is showing signs of life again, resulting in the
     introduction of the generic Linux/UEFI boot protocol, instead of
     x86 specific hacks which are increasingly difficult to maintain.
     There's hope that all future extensions will now go through that
     boot protocol.

   - Preparatory work for RISC-V EFI support.

  The main changes are:

   - Boot time GDT handling changes

   - Simplify handling of EFI properties table on arm64

   - Generic EFI stub cleanups, to improve command line handling, file
     I/O, memory allocation, etc.

   - Introduce a generic initrd loading method based on calling back
     into the firmware, instead of relying on the x86 EFI handover
     protocol or device tree.

   - Introduce a mixed mode boot method that does not rely on the x86
     EFI handover protocol either, and could potentially be adopted by
     other architectures (if another one ever surfaces where one
     execution mode is a superset of another)

   - Clean up the contents of 'struct efi', and move out everything that
     doesn't need to be stored there.

   - Incorporate support for UEFI spec v2.8A changes that permit
     firmware implementations to return EFI_UNSUPPORTED from UEFI
     runtime services at OS runtime, and expose a mask of which ones are
     supported or unsupported via a configuration table.

   - Partial fix for the lack of by-VA cache maintenance in the
     decompressor on 32-bit ARM.

   - Changes to load device firmware from EFI boot service memory
     regions

   - Various documentation updates and minor code cleanups and fixes"

* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
  efi/libstub/arm: Fix spurious message that an initrd was loaded
  efi/libstub/arm64: Avoid image_base value from efi_loaded_image
  partitions/efi: Fix partition name parsing in GUID partition entry
  efi/x86: Fix cast of image argument
  efi/libstub/x86: Use ULONG_MAX as upper bound for all allocations
  efi: Fix a mistype in comments mentioning efivar_entry_iter_begin()
  efi/libstub: Avoid linking libstub/lib-ksyms.o into vmlinux
  efi/x86: Preserve %ebx correctly in efi_set_virtual_address_map()
  efi/x86: Ignore the memory attributes table on i386
  efi/x86: Don't relocate the kernel unless necessary
  efi/x86: Remove extra headroom for setup block
  efi/x86: Add kernel preferred address to PE header
  efi/x86: Decompress at start of PE image load address
  x86/boot/compressed/32: Save the output address instead of recalculating it
  efi/libstub/x86: Deal with exit() boot service returning
  x86/boot: Use unsigned comparison for addresses
  efi/x86: Avoid using code32_start
  efi/x86: Make efi32_pe_entry() more readable
  efi/x86: Respect 32-bit ABI in efi32_pe_entry()
  efi/x86: Annotate the LOADED_IMAGE_PROTOCOL_GUID with SYM_DATA
  ...

Pull RCU updates from Ingo Molnar:
 "The main changes in this cycle were:

   - Make kfree_rcu() use kfree_bulk() for added performance

   - RCU updates

   - Callback-overload handling updates

   - Tasks-RCU KCSAN and sparse updates

   - Locking torture test and RCU torture test updates

   - Documentation updates

   - Miscellaneous fixes"

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (74 commits)
  rcu: Make rcu_barrier() account for offline no-CBs CPUs
  rcu: Mark rcu_state.gp_seq to detect concurrent writes
  Documentation/memory-barriers: Fix typos
  doc: Add rcutorture scripting to torture.txt
  doc/RCU/rcu: Use https instead of http if possible
  doc/RCU/rcu: Use absolute paths for non-rst files
  doc/RCU/rcu: Use ':ref:' for links to other docs
  doc/RCU/listRCU: Update example function name
  doc/RCU/listRCU: Fix typos in a example code snippets
  doc/RCU/Design: Remove remaining HTML tags in ReST files
  doc: Add some more RCU list patterns in the kernel
  rcutorture: Set KCSAN Kconfig options to detect more data races
  rcutorture: Manually clean up after rcu_barrier() failure
  rcutorture: Make rcu_torture_barrier_cbs() post from corresponding CPU
  rcuperf: Measure memory footprint during kfree_rcu() test
  rcutorture: Annotation lockless accesses to rcu_torture_current
  rcutorture: Add READ_ONCE() to rcu_torture_count and rcu_torture_batch
  rcutorture: Fix stray access to rcu_fwd_cb_nodelay
  rcutorture: Fix rcu_torture_one_read()/rcu_torture_writer() data race
  rcutorture: Make kvm-find-errors.sh abort on bad directory
  ...

Pull objtool updates from Ingo Molnar:
 "The biggest changes in this cycle were the vmlinux.o optimizations by
   Peter Zijlstra, which are preparatory and optimization work to run
   objtool against the much richer vmlinux.o object file, to perform
   new, whole-program section based logic. That work exposed a handful
   of problems with the existing code, which fixes and optimizations are
   merged here. The complete 'vmlinux.o and noinstr' work is still work
   in progress, targeted for v5.8.

  There's also assorted fixes and enhancements from Josh Poimboeuf.

  In particular I'd like to draw attention to commit 644592d3,
  which turns fatal objtool errors into failed kernel builds. This
  behavior is IMO now justified on multiple grounds (it's easy currently
  to not notice an essentially corrupted kernel build), and the commit
  has been in -next testing for several weeks, but there could still be
  build failures with old or weird toolchains. Should that be widespread
  or high profile enough then I'd suggest a quick revert, to not hold up
  the merge window"

* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
  objtool: Re-arrange validate_functions()
  objtool: Optimize find_rela_by_dest_range()
  objtool: Delete cleanup()
  objtool: Optimize read_sections()
  objtool: Optimize find_symbol_by_name()
  objtool: Resize insn_hash
  objtool: Rename find_containing_func()
  objtool: Optimize find_symbol_*() and read_symbols()
  objtool: Optimize find_section_by_name()
  objtool: Optimize find_section_by_index()
  objtool: Add a statistics mode
  objtool: Optimize find_symbol_by_index()
  x86/kexec: Make relocate_kernel_64.S objtool clean
  x86/kexec: Use RIP relative addressing
  objtool: Rename func_for_each_insn_all()
  objtool: Rename func_for_each_insn()
  objtool: Introduce validate_return()
  objtool: Improve call destination function detection
  objtool: Fix clang switch table edge case
  objtool: Add relocation check for alternative sections
  ...

Pull PNP subsystem updates from Rafael Wysocki:

 - Update MAINTAINERS to cover include/linux/pnp.h and add the
   linux-acpi list to the PNP entry in it

 - add the const modifier to the name field definition in struct
   pnp_driver

 - drop a pointer case in the RTC CMOS driver that has become redundant

All by Corentin Labbe.

* tag 'pnp-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  MAINTAINERS: Add linux-acpi list to PNP
  rtc: cmos: remove useless cast for driver_name
  PNP: constify driver name
  PNP: add missing include/linux/pnp.h to MAINTAINERS

Pull ACPI updates from Rafael Wysocki:

   - Update the ACPICA code in the kernel to the 20200214 upstream
     release including:

       * Fix to re-enable the sleep button after wakeup (Anchal
         Agarwal).

       * Fixes for mistakes in comments and typos (Bob Moore).

       * ASL-ASL+ converter updates (Erik Kaneda).

       * Type casting cleanups (Sven Barth).

   - Clean up the intialization of the EC driver and eliminate some dead
     code from it (Rafael Wysocki).

   - Clean up the quirk tables in the AC and battery drivers (Hans de
     Goede).

   - Fix the global lock handling on x86 to ignore unspecified bit
     positions in the global lock field (Jan Engelhardt).

   - Add a new "tiny" driver for ACPI button devices exposed by VMs to
     guest kernels to send signals directly to init (Josh Triplett).

   - Add a kernel parameter to disable ACPI BGRT on x86 (Alex Hung).

   - Make the ACPI PCI host bridge and fan drivers use scnprintf() to
     avoid potential buffer overflows (Takashi Iwai).

   - Clean up assorted pieces of code:

       * Reorder "asmlinkage" to make g++ happy (Alexey Dobriyan).

       * Drop unneeded variable initialization (Colin Ian King).

       * Add missing __acquires/__releases annotations (Jules Irenge).

       * Replace list_for_each_safe() with list_for_each_entry_safe()
         (chenqiwu)"

* tag 'acpi-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (31 commits)
  ACPICA: Update version to 20200214
  ACPI: PCI: Use scnprintf() for avoiding potential buffer overflow
  ACPI: fan: Use scnprintf() for avoiding potential buffer overflow
  ACPI: EC: Eliminate EC_FLAGS_QUERY_HANDSHAKE
  ACPI: EC: Do not clear boot_ec_is_ecdt in acpi_ec_add()
  ACPI: EC: Simplify acpi_ec_ecdt_start() and acpi_ec_init()
  ACPI: EC: Consolidate event handler installation code
  acpi/x86: ignore unspecified bit positions in the ACPI global lock field
  acpi/x86: add a kernel parameter to disable ACPI BGRT
  x86/acpi: make "asmlinkage" part first thing in the function definition
  ACPI: list_for_each_safe() -> list_for_each_entry_safe()
  ACPI: video: remove redundant assignments to variable result
  ACPI: OSL: Add missing __acquires/__releases annotations
  ACPI / battery: Cleanup Lenovo Ideapad Miix 320 DMI table entry
  ACPI / AC: Cleanup DMI quirk table
  ACPI: EC: Use fast path in acpi_ec_add() for DSDT boot EC
  ACPI: EC: Simplify acpi_ec_add()
  ACPI: EC: Drop AE_NOT_FOUND special case from ec_install_handlers()
  ACPI: EC: Avoid passing redundant argument to functions
  ACPI: EC: Avoid printing confusing messages in acpi_ec_setup()
  ...

Pull power management updates from Rafael Wysocki:
 "These clean up and rework the PM QoS API, address a suspend-to-idle
  wakeup regression on some ACPI-based platforms, clean up and extend a
  few cpuidle drivers, update multiple cpufreq drivers and cpufreq
  documentation, and fix a number of issues in devfreq and several other
  things all over.

  Specifics:

   - Clean up and rework the PM QoS API to simplify the code and reduce
     the size of it (Rafael Wysocki).

   - Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
     similar platforms where the USB plug/unplug events are handled by
     the EC (Rafael Wysocki).

   - CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
     Ulf Hansson).

   - Extend the haltpoll cpuidle driver so that it can be forced to run
     on some systems where it refused to load (Maciej Szmigiero).

   - Convert several cpufreq documents to the .rst format and move the
     legacy driver documentation into one common file (Mauro Carvalho
     Chehab, Rafael Wysocki).

   - Update several cpufreq drivers:

        * Extend and fix the imx-cpufreq-dt driver (Anson Huang).

        * Improve the -EPROBE_DEFER handling and fix unwanted CPU
          overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
          Christoph Niedermaier).

        * Add support for Krait based SoCs to the qcom driver (Ansuel
          Smith).

        * Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).

        * Add platform specific intermediate callbacks support to
          cpufreq-dt and update the imx6q driver (Peng Fan).

        * Simplify and consolidate some pieces of the intel_pstate
          driver and update its documentation (Rafael Wysocki, Alex
          Hung).

   - Fix several devfreq issues:

        * Remove unneeded extern keyword from a devfreq header file and
          use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
          DEVFREQ_GOV_INTERNAL (Chanwoo Choi).

        * Fix the handling of dev_pm_qos_remove_request() result
          (Leonard Crestez).

        * Use constant name for userspace governor (Pierre Kuo).

        * Get rid of doc warnings and fix a typo (Christophe JAILLET).

   - Use built-in RCU list checking in some places in the PM core to
     avoid false-positive RCU usage warnings (Madhuparna Bhowmik).

   - Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
     QoS routines (Qian Cai).

   - Fix removal of wakeup sources to avoid NULL pointer dereferences in
     a corner case (Neeraj Upadhyay).

   - Clean up the handling of hibernate compat ioctls and fix the
     related documentation (Eric Biggers).

   - Update the idle_inject power capping driver to use variable-length
     arrays instead of zero-length arrays (Gustavo Silva).

   - Fix list format in a PM QoS document (Randy Dunlap).

   - Make the cpufreq stats module use scnprintf() to avoid potential
     buffer overflows (Takashi Iwai).

   - Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).

   - Allow no domain-idle-states DT property in generic PM domains (Ulf
     Hansson).

   - Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
     Smythies)"

* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
  cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
  tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
  ACPI: PM: s2idle: Refine active GPEs check
  ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
  PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
  PM / devfreq: Get rid of some doc warnings
  PM / devfreq: Fix handling dev_pm_qos_remove_request result
  PM / devfreq: Fix a typo in a comment
  PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
  PM / devfreq: Remove unneeded extern keyword
  PM / devfreq: Use constant name of userspace governor
  ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
  cpufreq: qcom: Add support for krait based socs
  cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
  cpufreq: Use scnprintf() for avoiding potential buffer overflow
  cpuidle: psci: Split psci_dt_cpu_init_idle()
  PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
  PM / hibernate: Remove unnecessary compat ioctl overrides
  PM: hibernate: fix docs for ioctls that return loff_t via pointer
  Documentation: intel_pstate: update links for references
  ...

Pull spi and regulator updates from Mark Brown:
 "At one point in the release cycle I managed to fat finger things and
  apply some SPI fixes onto a regulator branch and merge that into the
  SPI tree, then pull in a change shared with the MTD tree moving the
  Mediatek quadspi driver over to become the Mediatek spi-nor driver in
  the SPI tree.

  This has made a mess which I only just noticed while preparing this
  and I can't see a sensible way to unpick things due to other
  subsequent merge commits especially the pull from MTD so it looks like
  the most sensible thing to do is give up and combine the two pull
  requests.

  Fortunately both subsystems were fairly quiet this cycle, the
  highlights are:

  regulator:

   - Support for Monoloithic Power Systems MP5416, MP8867 and MPS8869
     and Qualcomm PMI8994 and SMB208.

  SPI:

   - Lots of enhancements for spi-fsl-dspi, including XSPI mode support,
     from Vladimir Oltean.

   - Support for amlogic Meson G12A, IBM FSI, Mediatek spi-nor (moved
     from MTD), NXP i.MX8Mx, Rockchip PX30, RK3308 and RK3328, and
     Qualcomm Atheros AR934x/QCA95xx"

* tag 'regulator-spi-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (118 commits)
  spi: efm32: Convert to use GPIO descriptors
  regulator: qcom_smd: Add pmi8994 regulator support
  regulator: da9063: Fix get_mode() functions to read sleep field
  spi: spi-fsl-lpspi: Replace zero-length array with flexible-array member
  spi: spi-s3c24xx: Replace zero-length array with flexible-array member
  spi: stm32: Fix comments compilation warnings
  spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses
  spi: spi-fsl-dspi: Add support for LS1028A
  spi: spi-fsl-dspi: Move invariant configs out of dspi_transfer_one_message
  spi: spi-fsl-dspi: Fix interrupt-less DMA mode taking an XSPI code path
  spi: spi-fsl-dspi: Avoid NULL pointer in dspi_slave_abort for non-DMA mode
  spi: spi-fsl-dspi: Replace interruptible wait queue with a simple completion
  spi: spi-fsl-dspi: Protect against races on dspi->words_in_flight
  spi: spi-fsl-dspi: Avoid reading more data than written in EOQ mode
  spi: spi-fsl-dspi: Fix bits-per-word acceleration in DMA mode
  spi: spi-fsl-dspi: Fix little endian access to PUSHR CMD and TXDATA
  spi: spi-fsl-dspi: Don't access reserved fields in SPI_MCR
  regulator: driver.h: fix regulator_map_* function names
  regulator: da9063: fix suspend
  spi: mxs: Drop GPIO includes
  ...

Pull regma: update from Mark Brown:
 "Only one small documentation fix for regmap this time around"

* tag 'regmap-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: wrong descriptions in regmap_range_cfg

Pull staging and IIO driver updates from Greg KH:
 "Here is the big staging and IIO driver pull request for 5.7-rc1.

  We again end up deleting more code than we added here, thanks to
  finally getting rid of the old and obsolete wireless USB stuff, and
  the exfat code (which is coming in again through the vfs tree in a
  much cleaner version).

  But some code does come back, with the octeon drivers being found to
  actually be used in the wild, so those deletions are now reverted.

  Other than those major things, just loads and loads of tiny checkpatch
  cleanups all over the place, along with new IIO drivers and fixes.

  All have been in linux-next with no reported issues"

[ Stephen Rothwell points out some reported issues due to merge conflicts ]

* tag 'staging-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (415 commits)
  staging: vt6656: Use DIV_ROUND_UP macro instead of specific code
  staging: remove hp100 driver
  staging: wilc1000: Use crc7 in lib/ rather than a private copy
  Staging: rtl8192u: ieee80211: Use netdev_alert().
  Staging: rtl8192u: ieee80211: Use netdev_info() with network devices.
  Staging: rtl8192u: ieee80211: Use netdev_warn() for network devices.
  Staging: rtl8192u: ieee80211: Use netdev_dbg() for debug messages.
  staging: wlan-ng: fix use-after-free Read in hfa384x_usbin_callback
  staging: rtl8723bs: hal: Remove NULL check before kfree
  staging: rtl8723bs: hal: Correct typos in comments
  staging: rtl8723bs: os_dep: Correct typos in comments
  staging: rtl8723bs: core: Correct typos in comments
  staging: rtl8723bs: hal: Remove unnecessary cast on void pointer
  staging: rtl8188eu: cleanup long line in odm.c
  staging: rtl8723bs: hal: Compress return logic
  staging: rtl8723bs: rtw_cmd: Compress lines for immediate return
  staging: rtl8723bs: rtw_efuse: Compress lines for immediate return
  staging: wilc1000: remove label from examples in DT binding documentation
  staging: rtl8723bs: Remove blank line before '}' brace
  Staging: rtl8188eu: hal: Add space around operators
  ...

Pull driver core updates from Greg KH:
 "Here is the "big" set of driver core changes for 5.7-rc1.

  Nothing huge in here, just lots of little firmware core changes and
  use of new apis, a libfs fix, a debugfs api change, and some driver
  core deferred probe rework.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (44 commits)
  Revert "driver core: Set fw_devlink to "permissive" behavior by default"
  driver core: Set fw_devlink to "permissive" behavior by default
  driver core: Replace open-coded list_last_entry()
  driver core: Read atomic counter once in driver_probe_done()
  libfs: fix infoleak in simple_attr_read()
  driver core: Add device links from fwnode only for the primary device
  platform/x86: touchscreen_dmi: Add info for the Chuwi Vi8 Plus tablet
  platform/x86: touchscreen_dmi: Add EFI embedded firmware info support
  Input: icn8505 - Switch to firmware_request_platform for retreiving the fw
  Input: silead - Switch to firmware_request_platform for retreiving the fw
  selftests: firmware: Add firmware_request_platform tests
  test_firmware: add support for firmware_request_platform
  firmware: Add new platform fallback mechanism and firmware_request_platform()
  Revert "drivers: base: power: wakeup.c: Use built-in RCU list checking"
  drivers: base: power: wakeup.c: Use built-in RCU list checking
  component: allow missing unbind callback
  debugfs: remove return value of debugfs_create_file_size()
  debugfs: Check module state before warning in {full/open}_proxy_open()
  firmware: fix a double abort case with fw_load_sysfs_fallback
  arch_topology: Fix putting invalid cpu clk
  ...

Pull USB / PHY updates from Greg KH:
 "Here are the big set of USB and PHY driver patches for 5.7-rc1.

  Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
  updates, xhci updates, usb-serial driver updates and new device ids,
  and other minor things. Full details in the shortlog.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
  USB: cdc-acm: restore capability check order
  usb: cdns3: make signed 1 bit bitfields unsigned
  usb: gadget: fsl: remove unused variable 'driver_desc'
  usb: gadget: f_fs: Fix use after free issue as part of queue failure
  usb: typec: Correct the documentation for typec_cable_put()
  USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
  USB: serial: option: add Wistron Neweb D19Q1
  USB: serial: option: add BroadMobi BM806U
  USB: serial: option: add support for ASKEY WWHC050
  usb: core: Add ACPI support for USB interface devices
  driver core: platform: Reimplement devm_platform_ioremap_resource
  usb: dwc2: convert to devm_platform_get_and_ioremap_resource
  usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
  usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
  drivers: provide devm_platform_get_and_ioremap_resource()
  phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
  phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
  dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
  phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
  dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
  ...

Pull media updates from Mauro Carvalho Chehab:

 - New sensor driver: imx219

 - Support for some new pixelformats

 - Support for Sun8i SoC

 - Added more codecs to meson vdec driver

 - Prepare for removing the legacy usbvision driver by moving it to
   staging. This driver has issues and use legacy core APIs. If nobody
   steps up to address those, it is time for its retirement.

 - Several cleanups and improvements on drivers, with the addition of
   new supported boards

* tag 'media/v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (236 commits)
  media: venus: firmware: Ignore secure call error on first resume
  media: mtk-vpu: load vpu firmware from the new location
  media: i2c: video-i2c: fix build errors due to 'imply hwmon'
  media: MAINTAINERS: add myself to co-maintain Hantro G1/G2 for i.MX8MQ
  media: hantro: add initial i.MX8MQ support
  media: dt-bindings: Document i.MX8MQ VPU bindings
  media: vivid: fix incorrect PA assignment to HDMI outputs
  media: hantro: Add linux-rockchip mailing list to MAINTAINERS
  media: cedrus: h264: Fix 4K decoding on H6
  media: siano: Use scnprintf() for avoiding potential buffer overflow
  media: rc: Use scnprintf() for avoiding potential buffer overflow
  media: allegro: create new struct for channel parameters
  media: allegro: move mail definitions to separate file
  media: allegro: pass buffers through firmware
  media: allegro: verify source and destination buffer in VCU response
  media: allegro: handle dependency of bitrate and bitrate_peak
  media: allegro: read bitrate mode directly from control
  media: allegro: make QP configurable
  media: allegro: make frame rate configurable
  media: allegro: skip filler data if possible
  ...

Pull hwmon updates from Guenter Roeck:

 - New driver for AXI fan control

 - Attenuator bypass support and support for inverting pwm output in
   adt7475 driver

 - Support for new power supply version in ibm-cffps driver

 - PMBus drivers:

     * support for multi-phase chips

     * ltc2978 driver: add support for LTC2972, LTC2979, LTC3884,
       LTC3889, LTC7880, LTM4664, LTM4677, LTM4678, LTM4680, and
       LTM4700/

     * tps53679 driver: add support for TPS53681, TPS53647, and TPS53667

     * isl68137 driver: support for various 2nd Gen Renesas digital
       multiphase chips added to isl68137 driver

 - Minor improvements and fixes in nct7904, ibmpowernv, lm73, ibmaem,
   and k10temp drivers

* tag 'hwmon-for-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (29 commits)
  docs: hwmon: Update documentation for isl68137 pmbus driver
  hwmon: (pmbus) add support for 2nd Gen Renesas digital multiphase
  hwmon: (pmbus/ibm-cffps) Add another PSU CCIN to version detection
  hwmon: (nct7904) Fix the incorrect quantity for fan & temp attributes
  hwmon: (ibmpowernv) Use scnprintf() for avoiding potential buffer overflow
  hwmon: (adt7475) Add support for inverting pwm output
  hwmon: (adt7475) Add attenuator bypass support
  dt-bindings: hwmon: Document adt7475 pwm-active-state property
  dt-bindings: hwmon: Document adt7475 bypass-attenuator property
  dt-bindings: hwmon: Document adt7475 binding
  hwmon: (lm73) Add support for of_match_table
  dt-bindings: Add TI LM73 as a trivial device
  hwmon: (pmbus/tps53679) Add documentation
  hwmon: (pmbus/tps53679) Add support for TPS53647 and TPS53667
  hwmon: (pmbus/tps53679) Add support for TPS53681
  hwmon: (pmbus/tps53679) Add support for IIN and PIN to TPS53679 and TPS53688
  hwmon: (pmbus/tps53679) Add support for multiple chips IDs
  hwmon: (pmbus) Implement multi-phase support
  hwmon: (pmbus) Add 'phase' parameter where needed for multi-phase support
  hwmon: (pmbus) Add IC_DEVICE_ID and IC_DEVICE_REV command definitions
  ...

Pull RAS updates from Borislav Petkov:

 - Do not report spurious MCEs on some Intel platforms caused by errata;
   by Prarit Bhargava.

 - Change dev-mcelog's hardcoded limit of 32 error records to a dynamic
   one, controlled by the number of logical CPUs, by Tony Luck.

 - Add support for the processor identification number (PPIN) on AMD, by
   Wei Huang.

* tag 'ras_updates_for_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce/amd: Add PPIN support for AMD MCE
  x86/mce/dev-mcelog: Dynamically allocate space for machine check records
  x86/mce: Do not log spurious corrected mce errors

Pull EDAC updates from Borislav Petkov:

 - A substantial edac_mc cleanup, sanitizing object freeing,
   streamlining and simplifying code flow, and getting rid of a lot of
   needless complexity in memory controller representation code, by
   Robert Richter.

 - A new EDAC driver for the ARM DMC-520 memory controller, by Lei Wang,
   Shiping Ji and others.

 - The usual sprinkling of misc cleanups and fixes all over the
   subsystem.

* tag 'edac_updates_for_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/armada_xp: Use scnprintf() for avoiding potential buffer overflow
  EDAC/synopsys: Do not dump uninitialized pinf->col
  EDAC: Add EDAC driver for DMC520
  dt-bindings: edac: Dmc-520.yaml
  EDAC/mce_amd: Print !SMCA processor warning only once
  EDAC/mc: Remove per layer counters
  EDAC/mc: Remove detail[] string and cleanup error string generation
  EDAC/mc: Pass the error descriptor to error reporting functions
  EDAC/mc: Remove enable_per_layer_report function argument
  EDAC/mc: Report "unknown memory" on too many DIMM labels found
  EDAC/mc: Carve out error increment into a separate function
  EDAC/mc: Determine mci pointer from the error descriptor
  EDAC: Store error type in struct edac_raw_error_desc
  EDAC/mc: Reorder functions edac_mc_alloc*()
  EDAC/mc: Split edac_mc_alloc() into smaller functions
  EDAC/mc: Change mci device removal to use put_device()