When stopping the CSI2 receiver the s_stream handler will wait for the
IRQ handler to notice the stop request. The receiver, automatically
disabled by the hardware after each frame, is then not reenabled by the
IRQ handler as it returns immediately.

As the IRQ handler check is performed before handling the context IRQ,
the context IRQ source isn't cleared, and the CSI2 IRQ is then fired
again immediately. The IRQ handler then fails to notice that the module
is being stopped, processes the IRQ normally and reenables the CSI2
hardware.

The problem goes unnoticed at stream stop time, but depending on the IRQ
and s_stream scheduling timings, the CSI2 receiver can end up being
hanged and will not produce any interrupt the next time it gets enabled,
despite being soft-reset then.

Fix this by checking for module stop after clearing the context IRQ
source.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The chroma data base address for NV12 formatted data should begin offset
rows*bytes_per_row from the base address for luminance data. We were OBO
causing a stripe of green pixels at the bottom of the frame.
Signed-off-by: Nate Weibley <nweibley@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

UVC 1.5 devices report a bInterfaceProtocol value set to 1 in their
interface descriptors. The uvcvideo driver only matches on
bInterfaceProtocol 0, preventing those devices from being detected.

More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Microsoft Surface Pro 3 cameras have been
reported to work out of the box with the driver with an updated match
table.

Enable UVC 1.5 support in the match table to support the devices that
can work with the current driver implementation. Devices that can't will
fail, but that's hardly a regression as they're currently not detected
at all anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The variable "tsin" was checked three times in a loop iteration of the
c8sectpfe_tuner_unregister_frontend() function.
This implementation detail could be improved by the combination of the
involved statements into a single if block so that this variable will be
checked only once there.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The functions i2c_put_adapter() and module_put() test whether their
argument is NULL and then return immediately.
Thus the tests around their calls are not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Simplify the logging.

I had some doubts about using the elvis operator as it's GNU extension.
However GNU extensions are explicitely allowed and this operator is
used at several places in the kernel code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace nvt_pr with the respective dev_ functions thus slightly
simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Switch the info about the detected chip type from debug to info level
as it might be useful not only for debugging purposes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Instead of explicitely checking debug use nvt_dbg like in other parts
of the driver thus simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add support for the NCT6779D. It's found e.g. on the Zotac CI321 mini-pc
and I successfully tested it on this device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

nvt_hw_detect always returns 0, therefore make it return void.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Make the chip detection code more similar to the one used for the
same chips in watchdog/w83627hf_wdt.c and hwmon/w83627ehf.c.

Apart from better maintainability we gain
- unified naming of chips (e.g. 677C -> NCT6776F)
- driver works with all revisions of the chips
  (least 4 bits of id are masked)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Switch to managed resource handling using the devm_ functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

chip_major / chip_minor are accessed sequentially in probe only.
Therefore no lock is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Using IRQ_RETVAL is unneeded here. IRQ_NONE / IRQ_HANDLED can be
returned directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Denon also uses the Sharp protocol, however with different check bits.

It would have been also possible to add this as a separate protocol
but this may not be worth the effort.

Successfully tested with a Denon RC-1002 remote control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

streamzap uses 'struct timeval' to store the start time of a signal for
gap tracking. struct timeval uses a 32-bit seconds representation which
will overflow in year 2038 and beyond. Replace struct timeval with ktime_t
which uses a 64-bit seconds representation and is 2038 safe. This patch
uses ktime_get_real() preserving the use of wall-clock time in the
original code.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The Terratec Cinergy T XS is a DVB-T receiver with no analog TV tuner.
This patch adds support for the cards carrying the mt2060 tuner; it's
unclear whether there are cards sold under the same name which use a
different tuner.
As long as there are no reports of such cards, and indeed as long as
there are no working drivers for them, we assume that the USB device
[0ccd:0043] is carrying the mt2060 tuner.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

In case the request to locate the firmware file part 2 fails, the error
path releases the already freed firmware memory location again. Thus
reset the firmware pointer to NULL after releasing firmware file part 1.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

rc-main mistakenly uses #ifdef MODULE to determine whether it should
load the rc keymap modules.  This symbol is only defined if rc-main
is being built as a module itself, and bears no relation to whether
the rc keymaps are modules.

Fix this to use CONFIG_MODULES instead.

Fixes: 631493ec ("[media] rc-core: merge rc-map.c into rc-main.c")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

A previous patch added a check if the firmware is too big, but it didn't
set the return error code with the right value.

[mchehab@osg.samsung.com: I ended by applying a v1 of Laura's patch, without
 the proper return code. This patch contains the difference between v2 and v1 of
 the Laura's "si2157: Bounds check firmware" patch]
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Don't require V4L2 framework and I2C being linked to the kernel directly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Kernel headers should use linux/types.h instead.
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Return values of mxl111sf_enable_usb_output and mxl1x1sf_top_master_ctrl
are not validated.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Since commit 3d7608e4 ("ARM: shmobile: bockw: remove legacy
board file and config"), Renesas R-Car SoCs are only supported in
generic DT-only ARM multi-platform builds.  The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Now that media has its own subdirectory inside platform_data,
let's move the headers that are already there to such subdir.

After moving those files, the references were adjusted using this
script:

    MAIN_DIR="linux/platform_data/"
    PREV_DIR="linux/platform_data/"
    DIRS="media/"

    echo "Checking affected files" >&2
    for i in $DIRS; do
	for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
		 n=`basename $j`
		git grep -l $n
	done
    done|sort|uniq >files && (
	echo "Handling files..." >&2;
	echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
	(
		cd include/$MAIN_DIR;
		for j in $DIRS; do
			for i in $(ls $j); do
				echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
			done;
		done;
		echo "cat > a && mv a \$i; done";
	);
	echo "Handling documentation..." >&2;
	echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
	(
		cd include/$MAIN_DIR;
		for j in $DIRS; do
			for i in $(ls $j); do
				echo "  perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
			done;
		done;
		echo "cat > a && mv a \$i; done"
	);
    ) >script && . ./script
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Give JPU peripheral chance to finish current job.
Don't switch off clock until context release.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove redundant code. Following code line do what we want.

[mchehab@osg.samsung.com: fix conflict with VB2 split patches that renamed some structs]
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

It is possible to use:
	make DOCBOOKS=device-drivers.xml htmldocs

To produce just a few docbooks. In such case, the media docs
won't be built, causing the makefile target to return an error.

While this is ok for human eyes, if the above is used on an script,
it would cause troubles.

Fix it by only creating/filling the media_api directory if the
media_api.xml is found at DOCBOOKS.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.

Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.

This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.

The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: Eric Nelson <eric@nelint.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

A default timeout value of 125 ms should work for all decoders.

Declare a constant to help standardize its' use.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.

This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.

Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

commit f934a94b ('s5c73m3: Export OF
module alias information') broke compilation when compiled as module:

In file included from drivers/media/i2c/s5c73m3/s5c73m3-spi.c:22:0:
drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:40: error: expected ')' before ';' token
 MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids;);
                                        ^

Fix it by removing the extra ';'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

reset-gpios is more clear than rst-gpio.

This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Adding these properties makes the I2C bus to the demodulators much
more reliable, and we no longer suffer from I2C errors when tuning.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

When in FE_TUNE_MODE_ONESHOT the frontend must report
the actual capabilities so user can take appropriate
action.

With frontends that can't do auto inversion this is done
by dvb-core automatically so CAN_INVERSION_AUTO is valid.

However, when in FE_TUNE_MODE_ONESHOT this is not true.

So only set FE_CAN_INVERSION_AUTO in modes other than
FE_TUNE_MODE_ONESHOT
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>