into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux

Cures reported lockups.

into home.osdl.org:/home/torvalds/v2.5/linux

Some machines with the SIS 96x southbridge have it set up
to claim it is a SIS 503 chip. That breaks irq routing logic
among other things. Fix it properly by making everybody aware
of the duplicity.

into home.osdl.org:/home/torvalds/v2.5/linux

into nuts.ninka.net:/disk1/davem/BK/net-2.5

into kernel.bkbits.net:/home/davem/sparc-2.5

into home.osdl.org:/home/torvalds/v2.5/linux

JFS isn't happy it thinks a file has been removed, and link() increases
its nlink count back from zero.  In 2.4, i_zombie prevented this race
condition.

http://bugzilla.kernel.org/show_bug.cgi?id=866

__invalidate_metapages references mp->page after after releasing the
meta_lock spinlock, without increasing the use count.  This is racy and
unnecessary since setting the META_discard flag is sufficient.
block_invalidatepage() will be called when the metapage is released.

Bug reported by Paul Mackerras: if a module parameter fails, we didn't
call module_arch_cleanup().

On x86 this was harmless (module_arch_cleanup() is a no-op), but on
other architectures like PPC this causes inconsistent data structures
and subsequent oopses.

into home.osdl.org:/home/torvalds/v2.5/linux

This bug prevents Alphas with older firmware from booting if there
is a card with PCI-PCI bridge that supports 32-bit IO.
This has happened on AS2100 with a quad-tulip card, for example:
 - initially, the I/O window of 21152 bridge was 0x10000-0x10fff,
   as set up by firmware;
 - pci_setup_bridge() is going to change this, say, to 0xa000-0xafff:
   first, it updates PCI_IO_BASE_UPPER16 and PCI_IO_LIMIT_UPPER16
   registers, so that IO window temporarily is at 0x0000-0x0fff,
   which effectively blocks up all legacy IO ports in the lower
   4K range, such as serial, floppy, RTC an so on;
   does debugging printk - machine dies here with recursive
   machine checks as the serial console has gone.

Moving (or disabling) the debugging printk is not a solution -
there is possibility that timer interrupt (which might access RTC
ports) occurs between writes to lower and upper parts of the
base/limit registers.

The patch temporarily disables the IO window of the bridge by
setting PCI_IO_BASE_UPPER16 > PCI_IO_LIMIT_UPPER16 before doing
an update. It's safe, as we don't have any active IO behind
the bridge at this point. Also, it's a NOP for bridges with
16-bit-only IO.
Similar (but simpler, as we always clear upper 32 bits) fix
for 64-bit prefetchable MMIO range.

into home.osdl.org:/home/torvalds/v2.5/linux

into home.osdl.org:/home/torvalds/v2.5/linux

into flint.arm.linux.org.uk:/usr/src/bk/linux-2.6-serial

into flint.arm.linux.org.uk:/usr/src/bk/linux-2.6-serial

into home.osdl.org:/home/torvalds/v2.5/linux

(x >> 32) is undefined on a 32 bit integral variable in C; In contrast
(x >>16 >> 16) is fine (and gets optimized out to 0, while (x >> 32)
gets optimized out to a nop). 

Fix for starfire below

This fix got missed in the bonding patchset applied a while ago.

Ensure that arm ether drivers print the correct ether device name rather
than "eth%d".