vlan_insert_tag() and friends do not allocate a new skb.
However they might allocate a new skb->head.
Update their comments to better describe their behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

I have seen tcp_hashinfo starting at a non optimal location,
forcing input handlers to pull two cache lines instead of one,
and sharing a cache line that was dirtied more than necessary:

ffffffff83680600 b tcp_orphan_timer
ffffffff83680628 b tcp_orphan_cache
ffffffff8368062c b tcp_enable_tx_delay.__tcp_tx_delay_enabled
ffffffff83680630 B tcp_hashinfo
ffffffff83680680 b tcp_cong_list_lock

After this patch, ehash, ehash_locks, ehash_mask and ehash_locks_mask
are located in a read-only cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At present hwc timeout value is a fixed value. This patch sets the hwc
timeout from the hardware. It now uses a new hardware capability
GDMA_DRV_CAP_FLAG_1_HWC_TIMEOUT_RECONFIG to query and set the value
in hwc_timeout.
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a warning reported by coccinelle:

./drivers/net/ethernet/microchip/vcap/vcap_api.c:2399:9-16: WARNING:
ERR_CAST can be used with ri

Use ERR_CAST instead of ERR_PTR + PTR_ERR to simplify the
conversion process.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-6.6-20230803' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2023-08-03

This is a pull request of 9 patches for net-next/master.

The 1st patch is by Ruan Jinjie, targets the flexcan driver, and
cleans up the error handling of platform_get_irq() in the
flexcan_probe() function.

Markus Schneider-Pargmann contributes 6 patches for the tcan4x5x M_CAN
driver, consisting of some cleanups, and adding support for the
tcan4552/4553 chips.

Another patch by Ruan Jinjie, that cleans up the error path of
platform_get_irq() in the c_can_plat_probe() function of the C_CAN
platform driver.

The last patch is by Frank Jungclaus and adds support for the
CAN-USB/3 and CAN FD to the ESD USB CAN driver.
================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5aa83a4c ("  [PATCH] remove two obsolete net drivers") remove fmv18x_probe().
And commmit 01f46857 ("eth: amd: remove NI6510 support (ni65)") leave ni65_probe().
Commit a10079c6 ("staging: remove hp100 driver") remove hp100 driver and hp100_probe()
declaration is not used anymore.

sonic_probe() and iph5526_probe() are never implemented since the beginning of git history.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230802130716.37308-1-yuehaibing@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add missing include for DPAA (fix aarch64 build).
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308040620.ty8oYNOP-lkp@intel.com/
Fixes: 680ee045 ("net: invert the netdevice.h vs xdp.h dependency")
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20230803230008.362214-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Martin KaFai Lau says:

====================
pull-request: bpf-next 2023-08-03

We've added 54 non-merge commits during the last 10 day(s) which contain
a total of 84 files changed, 4026 insertions(+), 562 deletions(-).

The main changes are:

1) Add SO_REUSEPORT support for TC bpf_sk_assign from Lorenz Bauer,
   Daniel Borkmann

2) Support new insns from cpu v4 from Yonghong Song

3) Non-atomically allocate freelist during prefill from YiFei Zhu

4) Support defragmenting IPv(4|6) packets in BPF from Daniel Xu

5) Add tracepoint to xdp attaching failure from Leon Hwang

6) struct netdev_rx_queue and xdp.h reshuffling to reduce
   rebuild time from Jakub Kicinski

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (54 commits)
  net: invert the netdevice.h vs xdp.h dependency
  net: move struct netdev_rx_queue out of netdevice.h
  eth: add missing xdp.h includes in drivers
  selftests/bpf: Add testcase for xdp attaching failure tracepoint
  bpf, xdp: Add tracepoint to xdp attaching failure
  selftests/bpf: fix static assert compilation issue for test_cls_*.c
  bpf: fix bpf_probe_read_kernel prototype mismatch
  riscv, bpf: Adapt bpf trampoline to optimized riscv ftrace framework
  libbpf: fix typos in Makefile
  tracing: bpf: use struct trace_entry in struct syscall_tp_t
  bpf, devmap: Remove unused dtab field from bpf_dtab_netdev
  bpf, cpumap: Remove unused cmap field from bpf_cpu_map_entry
  netfilter: bpf: Only define get_proto_defrag_hook() if necessary
  bpf: Fix an array-index-out-of-bounds issue in disasm.c
  net: remove duplicate INDIRECT_CALLABLE_DECLARE of udp[6]_ehashfn
  docs/bpf: Fix malformed documentation
  bpf: selftests: Add defrag selftests
  bpf: selftests: Support custom type and proto for client sockets
  bpf: selftests: Support not connecting client socket
  netfilter: bpf: Support BPF_F_NETFILTER_IP_DEFRAG in netfilter link
  ...
====================

Link: https://lore.kernel.org/r/20230803174845.825419-1-martin.lau@linux.devSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

Conflicts:

net/dsa/port.c
  9945c1fb ("net: dsa: fix older DSA drivers using phylink")
  a88dd753 ("net: dsa: remove legacy_pre_march2020 detection")
https://lore.kernel.org/all/20230731102254.2c9868ca@canb.auug.org.au/

net/xdp/xsk.c
  3c5b4d69 ("net: annotate data-races around sk->sk_mark")
  b7f72a30 ("xsk: introduce wrappers and helpers for supporting multi-buffer in Tx path")
https://lore.kernel.org/all/20230731102631.39988412@canb.auug.org.au/

drivers/net/ethernet/broadcom/bnxt/bnxt.c
  37b61cda ("bnxt: don't handle XDP in netpoll")
  2b56b3d9 ("eth: bnxt: handle invalid Tx completions more gracefully")
https://lore.kernel.org/all/20230801101708.1dc7faac@canb.auug.org.au/

Adjacent changes:

drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_fs.c
  62da0833 ("net/mlx5e: Set proper IPsec source port in L4 selector")
  fbd51754 ("net/mlx5e: Add function to get IPsec offload namespace")

drivers/net/ethernet/sfc/selftest.c
  55c1528f ("sfc: fix field-spanning memcpy in selftest")
  ae9d445c ("sfc: Miscellaneous comment removals")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf and wireless.

  Nothing scary here. Feels like the first wave of regressions from v6.5
  is addressed - one outstanding fix still to come in TLS for the
  sendpage rework.

  Current release - regressions:

   - udp: fix __ip_append_data()'s handling of MSG_SPLICE_PAGES

   - dsa: fix older DSA drivers using phylink

  Previous releases - regressions:

   - gro: fix misuse of CB in udp socket lookup

   - mlx5: unregister devlink params in case interface is down

   - Revert "wifi: ath11k: Enable threaded NAPI"

  Previous releases - always broken:

   - sched: cls_u32: fix match key mis-addressing

   - sched: bind logic fixes for cls_fw, cls_u32 and cls_route

   - add bound checks to a number of places which hand-parse netlink

   - bpf: disable preemption in perf_event_output helpers code

   - qed: fix scheduling in a tasklet while getting stats

   - avoid using APIs which are not hardirq-safe in couple of drivers,
     when we may be in a hard IRQ (netconsole)

   - wifi: cfg80211: fix return value in scan logic, avoid page
     allocator warning

   - wifi: mt76: mt7615: do not advertise 5 GHz on first PHY of MT7615D
     (DBDC)

  Misc:

   - drop handful of inactive maintainers, put some new in place"

* tag 'net-6.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (98 commits)
  MAINTAINERS: update TUN/TAP maintainers
  test/vsock: remove vsock_perf executable on `make clean`
  tcp_metrics: fix data-race in tcpm_suck_dst() vs fastopen
  tcp_metrics: annotate data-races around tm->tcpm_net
  tcp_metrics: annotate data-races around tm->tcpm_vals[]
  tcp_metrics: annotate data-races around tm->tcpm_lock
  tcp_metrics: annotate data-races around tm->tcpm_stamp
  tcp_metrics: fix addr_same() helper
  prestera: fix fallback to previous version on same major version
  udp: Fix __ip_append_data()'s handling of MSG_SPLICE_PAGES
  net/mlx5e: Set proper IPsec source port in L4 selector
  net/mlx5: fs_core: Skip the FTs in the same FS_TYPE_PRIO_CHAINS fs_prio
  net/mlx5: fs_core: Make find_closest_ft more generic
  wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
  vxlan: Fix nexthop hash size
  ip6mr: Fix skb_under_panic in ip6mr_cache_report()
  s390/qeth: Don't call dev_close/dev_open (DOWN/UP)
  net: tap_open(): set sk_uid from current_fsuid()
  net: tun_chr_open(): set sk_uid from current_fsuid()
  net: dcb: choose correct policy to parse DCB_ATTR_BCN
  ...

Willem and Jason have agreed to take over the maintainer
duties for TUN/TAP, thank you!

There's an existing entry for TUN/TAP which only covers
the user mode Linux implementation.
Since we haven't heard from Maxim on the list for almost
a decade, extend that entry and take it over, rather than
adding a new one.
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20230802182843.4193099-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Martin KaFai Lau says:

====================
pull-request: bpf 2023-08-03

We've added 5 non-merge commits during the last 7 day(s) which contain
a total of 3 files changed, 37 insertions(+), 20 deletions(-).

The main changes are:

1) Disable preemption in perf_event_output helpers code,
   from Jiri Olsa

2) Add length check for SK_DIAG_BPF_STORAGE_REQ_MAP_FD parsing,
   from Lin Ma

3) Multiple warning splat fixes in cpumap from Hou Tao

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  bpf, cpumap: Handle skb as well when clean up ptr_ring
  bpf, cpumap: Make sure kthread is running before map update returns
  bpf: Add length check for SK_DIAG_BPF_STORAGE_REQ_MAP_FD parsing
  bpf: Disable preemption in bpf_event_output
  bpf: Disable preemption in bpf_perf_event_output
====================

Link: https://lore.kernel.org/r/20230803181429.994607-1-martin.lau@linux.devSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Kalle Valo says:

====================
wireless fixes for v6.5

We did some house cleaning in MAINTAINERS file so several patches
about that. Few regressions fixed and also fix some recently enabled
memcpy() warnings. Only small commits and nothing special standing
out.

* tag 'wireless-2023-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
  wifi: brcmfmac: Fix field-spanning write in brcmf_scan_params_v2_to_v1()
  wifi: ray_cs: Replace 1-element array with flexible array
  MAINTAINERS: add Jeff as ath10k, ath11k and ath12k maintainer
  MAINTAINERS: wifi: mark mlw8k as orphan
  MAINTAINERS: wifi: mark b43 as orphan
  MAINTAINERS: wifi: mark zd1211rw as orphan
  MAINTAINERS: wifi: mark wl3501 as orphan
  MAINTAINERS: wifi: mark rndis_wlan as orphan
  MAINTAINERS: wifi: mark ar5523 as orphan
  MAINTAINERS: wifi: mark cw1200 as orphan
  MAINTAINERS: wifi: atmel: mark as orphan
  MAINTAINERS: wifi: rtw88: change Ping as the maintainer
  Revert "wifi: ath6k: silence false positive -Wno-dangling-pointer warning on GCC 12"
  wifi: cfg80211: Fix return value in scan logic
  Revert "wifi: ath11k: Enable threaded NAPI"
  MAINTAINERS: Update mwifiex maintainer list
  wifi: mt76: mt7615: do not advertise 5 GHz on first phy of MT7615D (DBDC)
====================

Link: https://lore.kernel.org/r/20230803140058.57476C433C9@smtp.kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

We forgot to add vsock_perf to the rm command in the `clean`
target, so now we have a left over after `make clean` in
tools/testing/vsock.

Fixes: 8abbffd2 ("test/vsock: vsock_perf utility")
Cc: AVKrasnov@sberdevices.ru
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Link: https://lore.kernel.org/r/20230803085454.30897-1-sgarzare@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Eric Dumazet says:

====================
tcp_metrics: series of fixes

This series contains a fix for addr_same() and various
data-race annotations.

We still have to address races over tm->tcpm_saddr and
tm->tcpm_daddr later.
====================

Link: https://lore.kernel.org/r/20230802131500.1478140-1-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Whenever tcpm_new() reclaims an old entry, tcpm_suck_dst()
would overwrite data that could be read from tcp_fastopen_cache_get()
or tcp_metrics_fill_info().

We need to acquire fastopen_seqlock to maintain consistency.

For newly allocated objects, tcpm_new() can switch to kzalloc()
to avoid an extra fastopen_seqlock acquisition.

Fixes: 1fe4c481 ("net-tcp: Fast Open client - cookie cache")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230802131500.1478140-7-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tm->tcpm_net can be read or written locklessly.

Instead of changing write_pnet() and read_pnet() and potentially
hurt performance, add the needed READ_ONCE()/WRITE_ONCE()
in tm_net() and tcpm_new().

Fixes: 849e8a0c ("tcp_metrics: Add a field tcpm_net and verify it matches on lookup")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230802131500.1478140-6-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tm->tcpm_vals[] values can be read or written locklessly.

Add needed READ_ONCE()/WRITE_ONCE() to document this,
and force use of tcp_metric_get() and tcp_metric_set()

Fixes: 51c5d0c4 ("tcp: Maintain dynamic metrics in local cache.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

tm->tcpm_lock can be read or written locklessly.

Add needed READ_ONCE()/WRITE_ONCE() to document this.

Fixes: 51c5d0c4 ("tcp: Maintain dynamic metrics in local cache.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230802131500.1478140-4-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tm->tcpm_stamp can be read or written locklessly.

Add needed READ_ONCE()/WRITE_ONCE() to document this.

Also constify tcpm_check_stamp() dst argument.

Fixes: 51c5d0c4 ("tcp: Maintain dynamic metrics in local cache.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230802131500.1478140-3-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Because v4 and v6 families use separate inetpeer trees (respectively
net->ipv4.peers and net->ipv6.peers), inetpeer_addr_cmp(a, b) assumes
a & b share the same family.

tcp_metrics use a common hash table, where entries can have different
families.

We must therefore make sure to not call inetpeer_addr_cmp()
if the families do not match.

Fixes: d39d14ff ("net: Add helper function to compare inetpeer addresses")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230802131500.1478140-2-edumazet@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When both supported and previous version have the same major version,
and the firmwares are missing, the driver ends in a loop requesting the
same (previous) version over and over again:

    [   76.327413] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
    [   76.339802] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.352162] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.364502] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.376848] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.389183] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.401522] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.413860] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    [   76.426199] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
    ...

Fix this by inverting the check to that we aren't yet at the previous
version, and also check the minor version.

This also catches the case where both versions are the same, as it was
after commit bb5dbf2c ("net: marvell: prestera: add firmware v4.0
support").

With this fix applied:

    [   88.499622] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
    [   88.511995] Prestera DX 0000:01:00.0: failed to request previous firmware: mrvl/prestera/mvsw_prestera_fw-v4.0.img
    [   88.522403] Prestera DX: probe of 0000:01:00.0 failed with error -2

Fixes: 47f26018 ("net: marvell: prestera: try to load previous fw version")
Signed-off-by: Jonas Gorski <jonas.gorski@bisdn.de>
Acked-by: Elad Nachman <enachman@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Taras Chornyi <taras.chornyi@plvision.eu>
Link: https://lore.kernel.org/r/20230802092357.163944-1-jonas.gorski@bisdn.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
docs: net: page_pool: sync dev and kdoc

Document PP_FLAG_DMA_SYNC_DEV based on recent conversation.
Use kdoc to document structs and functions, to avoid duplication.

Olek, this will conflict with your work, but I think that trying
to make progress in parallel is the best course of action...
Retargetting at net-next to make it a little less bad.
====================

Link: https://lore.kernel.org/r/20230802161821.3621985-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

All struct members of the driver-facing APIs are documented twice,
in the code and under Documentation. This is a bit tedious.

I also get the feeling that a lot of developers will read the header
when coding, rather than the doc. Bring the two a little closer
together by using kdoc for structs and functions.

Using kdoc also gives us links (mentioning a function or struct
in the text gets replaced by a link to its doc).
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230802161821.3621985-3-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Using PP_FLAG_DMA_SYNC_DEV is a bit confusing. It was perhaps
more obvious when it was introduced but the page pool use
has grown beyond XDP and beyond packet-per-page so now
making the heads and tails out of this feature is not
trivial.

Obviously making the API more user friendly would be
a better fix, but until someone steps up to do that
let's at least document what the parameters are.

Relevant discussion in the first Link.

Link: https://lore.kernel.org/all/20230731114427.0da1f73b@kernel.org/Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Link: https://lore.kernel.org/r/20230802161821.3621985-2-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull nfsd fix from Chuck Lever:

 - Fix tmpfs splice read support

* tag 'nfsd-6.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  nfsd: Fix reading via splice

Pull erofs fixes from Gao Xiang:

 - Fix data corruption caused by insufficient decompression on
   deduplicated compressed extents

 - Drop a useless s_magic checking in erofs_kill_sb()

* tag 'erofs-for-6.5-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: drop unnecessary WARN_ON() in erofs_kill_sb()
  erofs: fix wrong primary bvec selection on deduplicated extents

Pull s390 fixes from Heiko Carstens:

 - Split kernel large page mappings into 4k mappings in case debug
   pagealloc is enabled again. This got accidentally removed by commit
   bb1520d5 ("s390/mm: start kernel with DAT enabled")

 - Fix error handling in KVM's sthyi handling

 - Add missing include to s390's uapi ptrace.h

 - Update defconfigs

* tag 's390-6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ptrace: add missing linux/const.h include
  KVM: s390: fix sthyi error handling
  s390: update defconfigs
  s390/vmem: split pages when debug pagealloc is enabled

Jakub Kicinski says:

====================
While poking at struct netdev_rx_queue I got annoyed by
the huge rebuild times. I split it out from netdevice.h
and then realized that it was the main reason we included
xdp.h in there. So I removed that dependency as well.

This gives us very pleasant build times for both xdp.h
and struct netdev_rx_queue changes.

I'm sending this for bpf-next because I think it'd be easiest
if it goes in there, and then bpf-next gets flushed soon after?
I can also make a branch on merge-base for net-next and bpf-next..

v2:
 - build fix
 - reorder some includes
v1: https://lore.kernel.org/all/20230802003246.2153774-1-kuba@kernel.org/
====================
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>

xdp.h is far more specific and is included in only 67 other
files vs netdevice.h's 1538 include sites.
Make xdp.h include netdevice.h, instead of the other way around.
This decreases the incremental allmodconfig builds size when
xdp.h is touched from 5947 to 662 objects.

Move bpf_prog_run_xdp() to xdp.h, seems appropriate and filter.h
is a mega-header in its own right so it's nice to avoid xdp.h
getting included there as well.

The only unfortunate part is that the typedef for xdp_features_t
has to move to netdevice.h, since its embedded in struct netdevice.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-4-kuba@kernel.orgSigned-off-by: Martin KaFai Lau <martin.lau@kernel.org>

struct netdev_rx_queue is touched in only a few places
and having it defined in netdevice.h brings in the dependency
on xdp.h, because struct xdp_rxq_info gets embedded in
struct netdev_rx_queue.

In prep for removal of xdp.h from netdevice.h move all
the netdev_rx_queue stuff to a new header.

We could technically break the new header up to avoid
the sysfs.h include but it's so rarely included it
doesn't seem to be worth it at this point.
Reviewed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-3-kuba@kernel.orgSigned-off-by: Martin KaFai Lau <martin.lau@kernel.org>

Handful of drivers currently expect to get xdp.h by virtue
of including netdevice.h. This will soon no longer be the case
so add explicit includes.
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://lore.kernel.org/r/20230803010230.1755386-2-kuba@kernel.orgSigned-off-by: Martin KaFai Lau <martin.lau@kernel.org>

The NULL initialization of the pointers assigned by kzalloc() first is
not necessary, because if the kzalloc() failed, the pointers will be
assigned NULL, otherwise it works as usual. so remove it.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230802040026.2588675-1-ruanjinjie@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Aaron Conole says:

====================
selftests: openvswitch: add flow programming cases

The openvswitch selftests currently contain a few cases for managing the
datapath, which includes creating datapath instances, adding interfaces,
and doing some basic feature / upcall tests.  This is useful to validate
the control path.

Add the ability to program some of the more common flows with actions. This
can be improved overtime to include regression testing, etc.
====================

Link: https://lore.kernel.org/r/20230801212226.909249-1-aconole@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Building on the previous work, add a very simplistic NAT case
using ipv4.  This just tests dnat transformation
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Forwarding via ct() action is an important use case for openvswitch, but
generally would require using a full ovs-vswitchd to get working. Add a
ct action parser for basic ct test case.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This is a simple ipv4 bidirectional connectivity test.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The default value for the mask actually depends on the value (e.g: if
the value is non-null, the default is full-mask), so change the convert
functions to accept the full, possibly masked string and let them figure
out how to parse the different values.

Also, implement size-aware int parsing.

With this patch we can now express flows such as the following:
"eth(src=0a:ca:fe:ca:fe:0a/ff:ff:00:00:ff:00)"
"eth(src=0a:ca:fe:ca:fe:0a)" -> mask = ff:ff:ff:ff:ff:ff
"ipv4(src=192.168.1.1)" -> mask = 255.255.255.255
"ipv4(src=192.168.1.1/24)"
"ipv4(src=192.168.1.1/255.255.255.0)"
"tcp(src=8080)" -> mask = 0xffff
"tcp(src=8080/0xf0f0)"
Signed-off-by: Adrian Moreno <amorenoz@redhat.com>
Acked-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The openvswitch self-tests can test much of the control side of
the module (ie: what a vswitchd implementation would process),
but the actual packet forwarding cases aren't supported, making
the testing of limited value.

Add some flow parsing and an initial ARP based test case using
arping utility.  This lets us display flows, add some basic
output flows with simple matches, and test against a known good
forwarding case.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Adrian Moreno <amorenoz@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

__ip6_append_data() can has a similar problem to __ip_append_data()[1] when
asked to splice into a partially-built UDP message that has more than the
frag-limit data and up to the MTU limit, but in the ipv6 case, it errors
out with EINVAL.  This can be triggered with something like:

        pipe(pfd);
        sfd = socket(AF_INET6, SOCK_DGRAM, 0);
        connect(sfd, ...);
        send(sfd, buffer, 8137, MSG_CONFIRM|MSG_MORE);
        write(pfd[1], buffer, 8);
        splice(pfd[0], 0, sfd, 0, 0x4ffe0ul, 0);

where the amount of data given to send() is dependent on the MTU size (in
this instance an interface with an MTU of 8192).

The problem is that the calculation of the amount to copy in
__ip6_append_data() goes negative in two places, but a check has been put
in to give an error in this case.

This happens because when pagedlen > 0 (which happens for MSG_ZEROCOPY and
MSG_SPLICE_PAGES), the terms in:

        copy = datalen - transhdrlen - fraggap - pagedlen;

then mostly cancel when pagedlen is substituted for, leaving just -fraggap.

Fix this by:

 (1) Insert a note about the dodgy calculation of 'copy'.

 (2) If MSG_SPLICE_PAGES, clear copy if it is negative from the above
     equation, so that 'offset' isn't regressed and 'length' isn't
     increased, which will mean that length and thus copy should match the
     amount left in the iterator.

 (3) When handling MSG_SPLICE_PAGES, give a warning and return -EIO if
     we're asked to splice more than is in the iterator.  It might be
     better to not give the warning or even just give a 'short' write.

 (4) If MSG_SPLICE_PAGES, override the copy<0 check.

[!] Note that this should also affect MSG_ZEROCOPY, but that will return
-EINVAL for the range of send sizes that requires the skbuff to be split.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: David Ahern <dsahern@kernel.org>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/000000000000881d0606004541d1@google.com/ [1]
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/1580952.1690961810@warthog.procyon.org.ukSigned-off-by: Paolo Abeni <pabeni@redhat.com>