Provides a timestamp in bss information so user space can see when the
bss info was updated. Since tsf is not available from the dongle events
boottime is reported instead.
Reported-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The mac address for p2pdev must be different from the primary interface
due to firmware requirement. Add an explicit check for this requirement
if user-space provides a mac address.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Trivial fix to spelling mistake in comment and in the ord_data text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Rename several macros that contain mispellings of UNKNOWN
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There is a potential execution path in which variable ret is returned
without being properly initialized previously.

Fix this by storing the value returned by function
rsi_usb_master_reg_write into _ret_.

Addresses-Coverity-ID: 1468407 ("Uninitialized scalar variable")
Fixes: 16d3bb7b ("rsi: disable fw watchdog timer during reset")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Function rsi_hal_key_config returns before reaching code at line
922 if (status), hence this code is structurally dead.

Fix this by storing the value returned by rsi_hal_load_key
into _status_ for its further evaluation and use.

Addresses-Coverity-ID: 1468409 ("Structurally dead code")
Fixes: 4fd6c476 ("rsi: roaming enhancements")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

pm_runtime handles sdio power on and power off transitions.
An old workaround for trying to control the power explicitly from the
driver was in fact causing failures on suspend/resume as the mmc layer
already power the module on resume.

In case of resume pm_runtime_get sync returns a positive device's usage
count causing the driver to try an re-initialize an already initialized
device. This was causing sdio bus failure on resume.

Remove this manual power on/off sequence as it is in-fact not needed.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

dma_tx_fragment() is never called in atomic context.

dma_tx_fragment() is only called by b43legacy_dma_tx(), which is
only called by b43legacy_tx_work().
b43legacy_tx_work() is only set a parameter of INIT_WORK() in
b43legacy_wireless_init().

Despite never getting called from atomic context,
dma_tx_fragment() calls alloc_skb() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.

This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

During changing virtual interface, keep using previous net device
mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When interface type changed, firmware using a new connction pointer.
We need Re-configure the mac address.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For user configurated mac address, directly set to firmware with no change.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.

Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The check within mt76_txq_send_burst is not enough, as it happens after
a first frame has already been queued up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fixes a reported lockdep error in mac80211:

[  179.867321] =============================
[  179.871510] WARNING: suspicious RCU usage
[  179.875528] 4.14.32 #0 Not tainted
[  179.878924] -----------------------------
[  179.882981] backports-2017-11-01/net/mac80211/tx.c:594 suspicious rcu_dereference_check() usage!
[  179.891785]
[  179.891785] other info that might help us debug this:
[  179.891785]
[  179.899824]
[  179.899824] rcu_scheduler_active = 2, debug_locks = 1
[  179.906343] 2 locks held by ksoftirqd/0/7:
[  179.910479]  #0:  (&(&q->lock)->rlock){+.-.}, at: [<86b207a4>] mt76_dma_tx_cleanup+0x64/0x354 [mt76]
[  179.919734]  #1:  (&(&fq->lock)->rlock){+.-.}, at: [<87238410>] ieee80211_tx_dequeue+0x54/0xc3c [mac80211]
[  179.929890]
[  179.929890] stack backtrace:
[  179.934257] CPU: 0 PID: 7 Comm: ksoftirqd/0 Not tainted 4.14.32 #0
[  179.940421] Stack : 00000000 00000000 00000000 00000000 80e0fce2 00000036 00000000 00000000
[  179.948864]         87c3d24c 80696377 8061039c 00000000 00000007 00000001 87c5db78 6534689d
[  179.957306]         00000000 00000000 80e10000 87c5da74 00000001 0000015a 00000007 00000000
[  179.965748]         00000000 806a0000 000e4171 00000000 00000000 00000000 ffffffff 00000001
[  179.974189]         806c0000 8692b240 86b000d0 87316fe4 00000001 802c9a68 00000000 80700000
[  179.982632]         ...
[  179.985104] Call Trace:
[  179.987582] [<80010a48>] show_stack+0x58/0x100
[  179.992040] [<804c2c58>] dump_stack+0xe8/0x170
[  179.996868] [<87234a04>] ieee80211_tx_h_select_key+0xa8/0x5b8 [mac80211]
[  180.004299] [<87238d44>] ieee80211_tx_dequeue+0x988/0xc3c [mac80211]
[  180.011048] [<86b230dc>] mt76_txq_schedule+0x110/0x3a4 [mt76]
[  180.016821] [<86b209d0>] mt76_dma_tx_cleanup+0x290/0x354 [mt76]
[  180.022777] [<86be2e60>] mt7603_tx_tasklet+0x40/0x6c [mt7603e]
[  180.028637] [<80037058>] tasklet_action+0x110/0x1ec
[  180.033532] [<804e1dac>] __do_softirq+0x164/0x35c
[  180.038235] [<80037174>] run_ksoftirqd+0x40/0x84
[  180.042870] [<800580c8>] smpboot_thread_fn+0x1a8/0x1d8
[  180.048023] [<800542e8>] kthread+0x130/0x144
[  180.052297] [<8000b1f8>] ret_from_kernel_thread+0x14/0x1c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Avoids having the tid or station entry disappear prematurely.
Also cancel the reorder work earlier to avoid further processing delayed
by waiting for the lock to be released
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add a spinlock in mt76_rx_complete. Without this, multiple stats updates
could happen in parallel, which can lead to deadlocks. There are
probably more corner cases fixed by this change.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix is_mt7612 routine since asic version is set in mt76_dev revision
field and not in mt76x2_dev one.
Moreover remove mt76x2_dev rev field since it is never used in the
driver

Fixes: 7bc04215 ('mt76: add driver code for MT76x2e')
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2018-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Second batch of iwlwifi patches for 4.18

* Some preparations for new hardware;
* A workaround to rescan the bus for the rare situation when older
  devices become irresponsive,
* Hardening of the firmware loading code to avoid issues with
  corrupted files;
* A few clean-ups and bugfixes.

In case of "any" wowlan trigger is configured, no valid wakeup filter
was configured.

Moreover, the fw assumes there's no connection when there are no configured
wakeup filters.
This leads to the station info not being updated on D3 command, causing
rate_n_flags to be 0 when the offloading code sends tx frame (triggering
SYSASSERT_102C due to invalid antenna param)

Note: "any" trigger is currently assumed to only be used when entering
d0i3 (which has a different flow). However, we still reach this code
when using d3_test.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Firmware will only send non low-latency TIDs in the
bitmap, so the check is now redundant.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The bitfield we use in struct iwl_cfg contains 17 bits, but we declare
it as u16.  The compiler doesn't seem to have any problems with that
(it probably automatically makes it u32), but it's cleaner to use a
type that is long enough for all the flags.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

If we fail to to grab NIC access because the device is not responding
(i.e. CSR_GP_CNTRL returns 0xFFFFFFFF), remove the device from the PCI
bus, to avoid any further damage, and to let the user space rescan.

In order to inform the userspace that a rescan is needed, we send a
kobject uevent with "INACCESSIBLE".

This functionality is disabled by default, but can be enabled via a
new module parameter called "remove_when_gone".  In the future we may
change this module parameter to include 3 modes instead: do nothing;
auto-rescan or; send uevent.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Rajat Jain <rajatja@google.com>

Now that we check and copy only the actual size of the page block,
there is no need to treat the last block separately.  Remove the
mostly duplicate code and make the main copy loop handle also the last
block.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The page loading code trusts the data provided in the firmware images
a bit too much and may cause a buffer overflow or copy unknown data if
the block sizes don't match what we expect.

To prevent potential problems, harden the code by checking if the
sizes we are copying are what we expect.

Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Future changes will require moving the HE radiotap data into
the SKB head, but this means we need to have the alignment
reservation done before that. To prepare, move the alignment
reservation earlier here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In future devices we use different csr addresses for hw addresses.
Update csr addresses to support new and legacy devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In case of A-MSDUs, the trans layer is taking care of building
the subframes (out of the given skb), according to the given gso_size.

However, in some testing flows, we want to build the whole A-MSDU
frame in a different place (e.g. userspace), and ask the driver
to send it as-is.

In case of gso_size==0, simply treat the frame as normal-frame,
although the A-MSDU flag is set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The max_data_size and max_inst_size values are only needed for DVM
devices.  Remove the assignment to those fields in 7000 and newer
families so we can also remove the otherwise unnecessary inclusion of
iwl-agn.h headers.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In future devices a new image will be introduced - IML. The IML, image
loader, is loaded by the ROM, and as part of the new self-init flow,
loads the rest of the firmware images to the device.

Store the image, so the ROM can load it to the device.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

To fix a conflict reported by Stephen Rothwell <sfr@canb.auug.org.au>:

Today's linux-next merge of the wireless-drivers-next tree got a
conflict in:

  drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c

between commit:

  77e30e10 ("iwlwifi: mvm: query regdb for wmm rule if needed")

from the wireless-drivers tree and commits:

  9c4f7d51 ("iwlwifi: move all NVM parsing code to the common files")
  4c625c56 ("iwlwifi: get rid of fw/nvm.c")

from the wireless-drivers-next tree.

ath.git patches for 4.18. Major changes:

ath10k

* enable temperature reads for QCA6174 and QCA9377

* add firmware memory dump support for QCA9984

* continue adding WCN3990 support via SNOC bus

In case memory resources for fw were succesfully allocated, release
them before jumping to fw_load_fail.

Addresses-Coverity-ID: 1466092 ("Resource leak")
Fixes: c3b2f7ca ("qtnfmac: implement asynchronous firmware loading")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

RT5370G has hardware RX antenna diversity like RT5390R.
Based on DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.bz2 manufacturer driver:
https://d86o2zu8ugzlg.cloudfront.net/mediatek-craft/drivers/DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.bz2

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: wireless newbie <wnewbie72@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux wireless ml <linux-wireless@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove and refactor some code in order to avoid having identical code
for different branches.

Notice that this piece of code hasn't been modified since 2011.

Addresses-Coverity-ID: 1226756 ("Identical code for different branches")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

BCM4366E is a wireless chipset with a BCM43664 ChipCommon. It's
supported by the same firmware as 4366c0.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
[arend: rebase patch and remove unnecessary definition]
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If "evt_len" is 1 then we try to memcpy() negative 3 bytes and it would
cause memory corruption.

Fixes: d930faee ("mwifiex: add support for Marvell pcie8766 chipset")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Firmware already support hidden ssid and keep ssid length,
Open the capability in driver.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Firmware parse and attach ERP IE from bss configuration,
do not set again from tail IE.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>