- 17 Jun, 2013 40 commits
-
-
Nicolin Chen authored
Enable WM8962 ALSA machine driver via devicetree. Signed-off-by:
Nicolin Chen <b42378@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Nicolin Chen authored
Enable SSI2 and its pin configuration in AUDMUX. Signed-off-by:
-
Nicolin Chen authored
Add WM8962 CODEC support and enable its parent I2C bus. Signed-off-by:
-
Nicolin Chen authored
On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10, so add a regulator controled by GPIO_4_10 for WM8962. Signed-off-by:
-
Nicolin Chen authored
Add a pinctrl for AUDMUX used on imx6dl-sabresd. Signed-off-by:
-
Nicolin Chen authored
Add a pinctrl for I2C1 used on imx6q/dl-sabresd. Signed-off-by:
-
Nicolin Chen authored
Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962. Signed-off-by:
-
Christian Hemp authored
Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01). - Module pfla02 - Carrier-Board pbab01 Signed-off-by:
Christian Hemp <c.hemp@phytec.de> Signed-off-by:
-
Christian Hemp authored
Add a group to the usdhc2 and enet pinctrl. Signed-off-by:
-
Alexander Shiyan authored
This patch adds name for NOR flash. This keeps compatibility for commandline partitions parsing from old bootloaders and make name of device same for DT and non-DT boot. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Acked-by:
Sascha Hauer <s.hauer@pengutonix.de> Signed-off-by:
-
Alexander Shiyan authored
This patch adds the SHDC devicetree node for PCM970 board. Signed-off-by:
-
Alexander Shiyan authored
This patch adds the missing SDHC devicetree nodes for i.MX27 SoCs. Signed-off-by:
-
Alexander Shiyan authored
This patch adds the missing DMA devicetree node for i.MX27 SoCs. Signed-off-by:
-
Huang Shijie authored
Enable the WEIM NOR for imx6q{dl}-sabreauto boards. For the pin conflict with SPI NOR, its status is set to "disabled". Signed-off-by:Huang Shijie <b32955@freescale.com> Signed-off-by:
-
Huang Shijie authored
Add two pinctrls for WEIM: one for the weim nor, another for the chipselect. Signed-off-by:
-
Huang Shijie authored
Add two pinctrls for WEIM: one for the weim nor, another for the chipselect. Signed-off-by:
-
Huang Shijie authored
Add the clock and compatible information for the weim. Also adds the weim label. Signed-off-by:
-
Huang Shijie authored
In the imx6q-sabreauto and imx6dl-sabreauto boards, the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but it is used as a data pin for the WEIM NOR. In order to fix the conflict, this patch removes the pin from the hog, and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto. The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled. Signed-off-by: -
Huang Shijie authored
The WEIM(Wireless External Interface Module) works like a bus. You can attach many different devices on it, such as NOR, onenand. In the case of i.MX6q-sabreauto, the NOR is connected to WEIM. This patch also adds the devicetree binding document. The driver only works when the devicetree is enabled. Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Markus Niebel authored
Add missing pin config Signed-off-by:
Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by:
-
Steffen Trumtrar authored
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads Signed-off-by:
-
Markus Niebel authored
Signed-off-by:
-
Markus Niebel authored
Add properties to make use of pca9554 gpio expander. Signed-off-by:
-
Markus Niebel authored
Enable the sgtl5000 found on MBa53 mainboard. Also enable audio muxer and ssi, which are needed for sound to work. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Enable tve on MBa53. Signed-off-by:
-
Sascha Hauer authored
As the displays are optional and we have more than one, also set the status of the parallel display and the ldb to disabled. Signed-off-by:
-
Michael Olbrich authored
Signed-off-by:
Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by:
-
Steffen Trumtrar authored
Add WP/CD pinctrl for esdhc2. Also, add vmmc-supply for esdhc2. Signed-off-by:
-
Philipp Zabel authored
This adds the Television Encoder (TVEv2) device tree node to the i.MX53 dtsi. Signed-off-by:
-
Philipp Zabel authored
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19. Add #PHY_RESET and LCD_CONTRAST. Signed-off-by:
-
Philipp Zabel authored
BIT(31) is NO_PAD_CTL, not BIT(16) Signed-off-by:
-
Sascha Hauer authored
It's active high, not active low. Signed-off-by:
-
Alexander Shiyan authored
Patch adds initial dts for Phytec PCM970 Rapid development kit. - Added definition for UART0 and UART1. - Added additional SPI chipselect which used on RDK for ZegBee module. Signed-off-by:
-
Alexander Shiyan authored
UART1 and UART2 can be unused on some designs with PCM038 module. Remove these definitions from basic dts and lets choose user only necessary UARTs in custom designs. Keep UART0 for using this one as boot console, but since we have not way to disable usage RTSCTS signals, remove this parameter for UART0. Signed-off-by:
-
Alexander Shiyan authored
PCM038 dts can be used as base for development kit board or any custom PCB designs. Renames this file to match functionality. Signed-off-by:
-
Alexander Shiyan authored
FEC (KSZ8001L) reset pin is connected to GPIOC30. Add this definition to dts. Signed-off-by:
-
Jingchang Lu authored
Add initial Freescale Vybrid VF610 Tower board support with uart and fec enabled. Signed-off-by:
Jingchang Lu <b35083@freescale.com> Signed-off-by:
-
Jingchang Lu authored
Add SoC level device tree source for Freescale Vybrid VF610. Signed-off-by:
-
Jonas Andersson authored
Add a group to the fec pinctrl, for use with MII interface. Signed-off-by:
Jonas Andersson <jonas@microbit.se> Signed-off-by:
-
Jonas Andersson authored
Add ecspi2 pinctrl. Signed-off-by:
-
