- 15 Sep, 2017 40 commits
-
-
Thinh Nguyen authored
commit dc9217b6 upstream. f_mass_storage has a memorry barrier issue with the sleep and wake functions that can cause a deadlock. This results in intermittent hangs during MSC file transfer. The host will reset the device after receiving no response to resume the transfer. This issue is seen when dwc3 is processing 2 transfer-in-progress events at the same time, invoking completion handlers for CSW and CBW. Also this issue occurs depending on the system timing and latency. To increase the chance to hit this issue, you can force dwc3 driver to wait and process those 2 events at once by adding a small delay (~100us) in dwc3_check_event_buf() whenever the request is for CSW and read the event count again. Avoid debugging with printk and ftrace as extra delays and memory barrier will mask this issue. Scenario which can lead to failure: ----------------------------------- 1) The main thread sleeps and waits for the next command in get_next_command(). 2) bulk_in_complete() wakes up main thread for CSW. 3) bulk_out_complete() tries to wake up the running main thread for CBW. 4) thread_wakeup_needed is not loaded with correct value in sleep_thread(). 5) Main thread goes to sleep again. The pattern is shown below. Note the 2 critical variables. * common->thread_wakeup_needed * bh->state CPU 0 (sleep_thread) CPU 1 (wakeup_thread) ============================== =============================== bh->state = BH_STATE_FULL; smp_wmb(); thread_wakeup_needed = 0; thread_wakeup_needed = 1; smp_rmb(); if (bh->state != BH_STATE_FULL) sleep again ... As pointed out by Alan Stern, this is an R-pattern issue. The issue can be seen when there are two wakeups in quick succession. The thread_wakeup_needed can be overwritten in sleep_thread, and the read of the bh->state maybe reordered before the write to thread_wakeup_needed. This patch applies full memory barrier smp_mb() in both sleep_thread() and wakeup_thread() to ensure the order which the thread_wakeup_needed and bh->state are written and loaded. However, a better solution in the future would be to use wait_queue method that takes care of managing memory barrier between waker and waiter. Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> [bwh: Backported to 3.16: adjust filename] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Mintz, Yuval authored
commit 3968d389 upstream. Apparently multi-cos isn't working for bnx2x quite some time - driver implements ndo_select_queue() to allow queue-selection for FCoE, but the regular L2 flow would cause it to modulo the fallback's result by the number of queues. The fallback would return a queue matching the needed tc [via __skb_tx_hash()], but since the modulo is by the number of TSS queues where number of TCs is not accounted, transmission would always be done by a queue configured into using TC0. Fixes: ada7c19e ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash") Signed-off-by:
Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Jeff Mahoney authored
commit 896533a7 upstream. If we fail to add the space_info kobject, we'll leak the memory for the percpu counter. Fixes: 6ab0a202 (btrfs: publish allocation data in sysfs) Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Reviewed-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
David Sterba authored
commit cc2b702c upstream. Variables start_idx and end_idx are supposed to hold a page index derived from the file offsets. The int type is not the right one though, offsets larger than 1 << 44 will get silently trimmed off the high bits. (1 << 44 is 16TiB) What can go wrong, if start is below the boundary and end gets trimmed: - if there's a page after start, we'll find it (radix_tree_gang_lookup_slot) - the final check "if (page->index <= end_idx)" will unexpectedly fail The function will return false, ie. "there's no page in the range", although there is at least one. btrfs_page_exists_in_range is used to prevent races in: * in hole punching, where we make sure there are not pages in the truncated range, otherwise we'll wait for them to finish and redo truncation, but we're going to replace the pages with holes anyway so the only problem is the intermediate state * lock_extent_direct: we want to make sure there are no pages before we lock and start DIO, to prevent stale data reads For practical occurence of the bug, there are several constaints. The file must be quite large, the affected range must cross the 16TiB boundary and the internal state of the file pages and pending operations must match. Also, we must not have started any ordered data in the range, otherwise we don't even reach the buggy function check. DIO locking tries hard in several places to avoid deadlocks with buffered IO and avoids waiting for ranges. The worst consequence seems to be stale data read. CC: Liu Bo <bo.li.liu@oracle.com> Fixes: fc4adbff ("btrfs: Drop EXTENT_UPTODATE check in hole punching and direct locking") Reviewed-by:
-
Michael Ellerman authored
commit 99acc9be upstream. If a process dumps core while it has SPU contexts active then we have code to also dump information about the SPU contexts. Unfortunately it's been broken for 3 1/2 years, and we didn't notice. In commit 7b1f4020 ("spufs: get rid of dump_emit() wrappers") the nread variable was removed and rc used instead. That means when the loop exits successfully, rc has the number of bytes read, but it's then used as the return value for the function, which should return 0 on success. So fix it by setting rc = 0 before returning in the success case. Fixes: 7b1f4020 ("spufs: get rid of dump_emit() wrappers") Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Acked-by:
Jeremy Kerr <jk@ozlabs.org> Signed-off-by:
-
Jiang Yi authored
commit 5e0cf5e6 upstream. There are three timing problems in the kthread usages of iscsi_target_mod: - np_thread of struct iscsi_np - rx_thread and tx_thread of struct iscsi_conn In iscsit_close_connection(), it calls send_sig(SIGINT, conn->tx_thread, 1); kthread_stop(conn->tx_thread); In conn->tx_thread, which is iscsi_target_tx_thread(), when it receive SIGINT the kthread will exit without checking the return value of kthread_should_stop(). So if iscsi_target_tx_thread() exit right between send_sig(SIGINT...) and kthread_stop(...), the kthread_stop() will try to stop an already stopped kthread. This is invalid according to the documentation of kthread_stop(). (Fix -ECONNRESET logout handling in iscsi_target_tx_thread and early iscsi_target_rx_thread failure case - nab) Signed-off-by:
Jiang Yi <jiangyilism@gmail.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Nicholas Bellinger authored
commit 25cdda95 upstream. This patch fixes a OOPs originally introduced by: commit bb048357 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Thu Sep 5 14:54:04 2013 -0700 iscsi-target: Add sk->sk_state_change to cleanup after TCP failure which would trigger a NULL pointer dereference when a TCP connection was closed asynchronously via iscsi_target_sk_state_change(), but only when the initial PDU processing in iscsi_target_do_login() from iscsi_np process context was blocked waiting for backend I/O to complete. To address this issue, this patch makes the following changes. First, it introduces some common helper functions used for checking socket closing state, checking login_flags, and atomically checking socket closing state + setting login_flags. Second, it introduces a LOGIN_FLAGS_INITIAL_PDU bit to know when a TCP connection has dropped via iscsi_target_sk_state_change(), but the initial PDU processing within iscsi_target_do_login() in iscsi_np context is still running. For this case, it sets LOGIN_FLAGS_CLOSED, but doesn't invoke schedule_delayed_work(). The original NULL pointer dereference case reported by MNC is now handled by iscsi_target_do_login() doing a iscsi_target_sk_check_close() before transitioning to FFP to determine when the socket has already closed, or iscsi_target_start_negotiation() if the login needs to exchange more PDUs (eg: iscsi_target_do_login returned 0) but the socket has closed. For both of these cases, the cleanup up of remaining connection resources will occur in iscsi_target_start_negotiation() from iscsi_np process context once the failure is detected. Finally, to handle to case where iscsi_target_sk_state_change() is called after the initial PDU procesing is complete, it now invokes conn->login_work -> iscsi_target_do_login_rx() to perform cleanup once existing iscsi_target_sk_check_close() checks detect connection failure. For this case, the cleanup of remaining connection resources will occur in iscsi_target_do_login_rx() from delayed workqueue process context once the failure is detected. Reported-by:
Mike Christie <mchristi@redhat.com> Reviewed-by:
Hannes Reinecke <hare@suse.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Sagi Grimberg <sagi@grimberg.me> Cc: Varun Prakash <varun@chelsio.com> Signed-off-by:
-
Bart Van Assche authored
commit 1efaa949 upstream. This patch avoids that smatch complains about inconsistent indentation in iscsi_target_start_negotiation(). Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Cc: Nicholas A. Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit 8f0dfb3d upstream. There is a iscsi-target/tcp login race in LOGIN_FLAGS_READY state assignment that can result in frequent errors during iscsi discovery: "iSCSI Login negotiation failed." To address this bug, move the initial LOGIN_FLAGS_READY assignment ahead of iscsi_target_do_login() when handling the initial iscsi_target_start_negotiation() request PDU during connection login. As iscsi_target_do_login_rx() work_struct callback is clearing LOGIN_FLAGS_READ_ACTIVE after subsequent calls to iscsi_target_do_login(), the early sk_data_ready ahead of the first iscsi_target_do_login() expects LOGIN_FLAGS_READY to also be set for the initial login request PDU. As reported by Maged, this was first obsered using an MSFT initiator running across multiple VMWare host virtual machines with iscsi-target/tcp. Reported-by:
Maged Mokhtar <mmokhtar@binarykinetics.com> Tested-by:
-
Russell King authored
commit 898805e0 upstream. The Marvell driver incorrectly provides phydev->lp_advertising as the logical and of the link partner's advert and our advert. This is incorrect - this field is supposed to store the link parter's unmodified advertisment. This allows ethtool to report the correct link partner auto-negotiation status. Fixes: be937f1f ("Marvell PHY m88e1111 driver fix") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Jan Kara authored
commit 67a7d5f5 upstream. Currently, extent manipulation operations such as hole punch, range zeroing, or extent shifting do not record the fact that file data has changed and thus fdatasync(2) has a work to do. As a result if we crash e.g. after a punch hole and fdatasync, user can still possibly see the punched out data after journal replay. Test generic/392 fails due to these problems. Fix the problem by properly marking that file data has changed in these operations. Fixes: a4bb6b64Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.16: drop change in ext4_insert_range()] Signed-off-by:
-
Jan Kara authored
commit a056bdaa upstream. mpage_submit_page() can race with another process growing i_size and writing data via mmap to the written-back page. As mpage_submit_page() samples i_size too early, it may happen that ext4_bio_write_page() zeroes out too large tail of the page and thus corrupts user data. Fix the problem by sampling i_size only after the page has been write-protected in page tables by clear_page_dirty_for_io() call. Reported-by:
Michael Zimmer <michael@swarm64.com> Fixes: cb20d518Signed-off-by:
-
Uwe Kleine-König authored
commit 82533ad9 upstream. The function ax_init_dev (which is called only from the driver's .probe function) calls free_irq in the error path without having requested the irq in the first place. So drop the free_irq call in the error path. Fixes: 825a2ff1 ("AX88796 network driver") Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Wei Wang authored
commit ba615f67 upstream. Fastopen API should be used to perform fastopen operations on the TCP socket. It does not make sense to use fastopen API to perform disconnect by calling it with AF_UNSPEC. The fastopen data path is also prone to race conditions and bugs when using with AF_UNSPEC. One issue reported and analyzed by Vegard Nossum is as follows: +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Thread A: Thread B: ------------------------------------------------------------------------ sendto() - tcp_sendmsg() - sk_stream_memory_free() = 0 - goto wait_for_sndbuf - sk_stream_wait_memory() - sk_wait_event() // sleep | sendto(flags=MSG_FASTOPEN, dest_addr=AF_UNSPEC) | - tcp_sendmsg() | - tcp_sendmsg_fastopen() | - __inet_stream_connect() | - tcp_disconnect() //because of AF_UNSPEC | - tcp_transmit_skb()// send RST | - return 0; // no reconnect! | - sk_stream_wait_connect() | - sock_error() | - xchg(&sk->sk_err, 0) | - return -ECONNRESET - ... // wake up, see sk->sk_err == 0 - skb_entail() on TCP_CLOSE socket If the connection is reopened then we will send a brand new SYN packet after thread A has already queued a buffer. At this point I think the socket internal state (sequence numbers etc.) becomes messed up. When the new connection is closed, the FIN-ACK is rejected because the sequence number is outside the window. The other side tries to retransmit, but __tcp_retransmit_skb() calls tcp_trim_head() on an empty skb which corrupts the skb data length and hits a BUG() in copy_and_csum_bits(). +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Hence, this patch adds a check for AF_UNSPEC in the fastopen data path and return EOPNOTSUPP to user if such case happens. Fixes: cf60af03 ("tcp: Fast Open client - sendmsg(MSG_FASTOPEN)") Reported-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
Wei Wang <weiwan@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Jan Kara authored
commit 5375023a upstream. XFS SEEK_HOLE implementation could miss a hole in an unwritten extent as can be seen by the following command: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (49.312 MiB/sec and 12623.9856 ops/sec) wrote 8192/8192 bytes at offset 131072 8 KiB, 2 ops; 0.0000 sec (70.383 MiB/sec and 18018.0180 ops/sec) Whence Result HOLE 139264 Where we can see that hole at offset 56k was just ignored by SEEK_HOLE implementation. The bug is in xfs_find_get_desired_pgoff() which does not properly detect the case when pages are not contiguous. Fix the problem by properly detecting when found page has larger offset than expected. Fixes: d126d43fSigned-off-by:
Brian Foster <bfoster@redhat.com> Reviewed-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
-
Eryu Guan authored
commit 8affebe1 upstream. xfs_find_get_desired_pgoff() is used to search for offset of hole or data in page range [index, end] (both inclusive), and the max number of pages to search should be at least one, if end == index. Otherwise the only page is missed and no hole or data is found, which is not correct. When block size is smaller than page size, this can be demonstrated by preallocating a file with size smaller than page size and writing data to the last block. E.g. run this xfs_io command on a 1k block size XFS on x86_64 host. # xfs_io -fc "falloc 0 3k" -c "pwrite 2k 1k" \ -c "seek -d 0" /mnt/xfs/testfile wrote 1024/1024 bytes at offset 2048 1 KiB, 1 ops; 0.0000 sec (33.675 MiB/sec and 34482.7586 ops/sec) Whence Result DATA EOF Data at offset 2k was missed, and lseek(2) returned ENXIO. This is uncovered by generic/285 subtest 07 and 08 on ppc64 host, where pagesize is 64k. Because a recent change to generic/285 reduced the preallocated file size to smaller than 64k. Signed-off-by:
Eryu Guan <eguan@redhat.com> Reviewed-by:
-
Lyude authored
commit 3d18e337 upstream. We end up reading the interrupt register for HPD5, and then writing it to HPD6 which on systems without anything using HPD5 results in permanently disabling hotplug on one of the display outputs after the first time we acknowledge a hotplug interrupt from the GPU. This code is really bad. But for now, let's just fix this. I will hopefully have a large patch series to refactor all of this soon. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Lyude <lyude@redhat.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> [bwh: Backported to 3.16: drop the DC_HPD6_RX_INTERRUPT cases] Signed-off-by:
-
Alex Deucher authored
commit 58d7e3e4 upstream. Even if the vblank period would allow it, it still seems to be problematic on some cards. v2: fix logic inversion (Nils) bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868Acked-by:
-
Andrew Lunn authored
commit f2899788 upstream. The 88m1101 has an errata when configuring autoneg. However, it was being applied to many other Marvell PHYs as well. Limit its scope to just the 88m1101. Fixes: 76884679 ("phylib: Add support for Marvell 88e1111S and 88e1145") Reported-by:
Daniel Walker <danielwa@cisco.com> Signed-off-by:
Harini Katakam <harinik@xilinx.com> Reviewed-by:
-
Johannes Thumshirn authored
commit ddff7ed4 upstream. When pci_enable_device() or pci_enable_device_mem() fail in qla2x00_probe_one() we bail out but do a call to pci_disable_device(). This causes the dev_WARN_ON() in pci_disable_device() to trigger, as the device wasn't enabled previously. So instead of taking the 'probe_out' error path we can directly return *iff* one of the pci_enable_device() calls fails. Additionally rename the 'probe_out' goto label's name to the more descriptive 'disable_device'. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring") Reviewed-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Takashi Iwai authored
commit 4efda5f2 upstream. soc_cleanup_card_resources() call snd_card_free() at the last of its procedure. This turned out to lead to a use-after-free. PCM runtimes have been already removed via soc_remove_pcm_runtimes(), while it's dereferenced later in soc_pcm_free() called via snd_card_free(). The fix is simple: just move the snd_card_free() call to the beginning of the whole procedure. This also gives another benefit: it guarantees that all operations have been shut down before actually releasing the resources, which was racy until now. Reported-and-tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Mark Brown <broonie@kernel.org> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
Liping Zhang authored
commit fefa9267 upstream. If nf_conntrack_htable_size was adjusted by the user during the ct dump operation, we may invoke nf_ct_put twice for the same ct, i.e. the "last" ct. This will cause the ct will be freed but still linked in hash buckets. It's very easy to reproduce the problem by the following commands: # while : ; do echo $RANDOM > /proc/sys/net/netfilter/nf_conntrack_buckets done # while : ; do conntrack -L done # iperf -s 127.0.0.1 & # iperf -c 127.0.0.1 -P 60 -t 36000 After a while, the system will hang like this: NMI watchdog: BUG: soft lockup - CPU#1 stuck for 22s! [bash:20184] NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [iperf:20382] ... So at last if we find cb->args[1] is equal to "last", this means hash resize happened, then we can set cb->args[1] to 0 to fix the above issue. Fixes: d205dc40 ("[NETFILTER]: ctnetlink: fix deadlock in table dumping") Signed-off-by:
Liping Zhang <zlpnobody@gmail.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Benjamin Peterson authored
commit c9525a3f upstream. Signed-off-by:
Benjamin Peterson <bp@benjamin.pe> Acked-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 9919cba7 ("watchdog: Update documentation") Link: http://lkml.kernel.org/r/20170521002016.13258-1-bp@benjamin.peSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Alexander Sverdlin authored
commit 0037ae47 upstream. The current buffer is being reset to zero on device_free_chan_resources() but not on device_terminate_all(). It could happen that HW is restarted and expects BASE0 to be used, but the driver is not synchronized and will start from BASE1. One solution is to reset the buffer explicitly in m2p_hw_setup(). Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Patrik Jakobsson authored
commit 82bc9a42 upstream. With LVDS we were incorrectly picking the pre-programmed mode instead of the prefered mode provided by VBT. Make sure we pick the VBT mode if one is provided. It is likely that the mode read-out code is still wrong but this patch fixes the immediate problem on most machines. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78562Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170418114332.12183-1-patrik.r.jakobsson@gmail.comSigned-off-by:
-
Dan Carpenter authored
commit 293dffaa upstream. If there is not enough space then ceph_decode_32_safe() does a goto bad. We need to return an error code in that situation. The current code returns ERR_PTR(0) which is NULL. The callers are not expecting that and it results in a NULL dereference. Fixes: f24e9980 ("ceph: OSD client") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
Ilya Dryomov <idryomov@gmail.com> Signed-off-by:
-
Dan Carpenter authored
commit 7bd897cf upstream. We don't set an error code on this path. It means that we return NULL instead of an error pointer and the caller does a NULL dereference. Fixes: 6d1d8050 ("block, partition: add partition_meta_info to hd_struct") Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Uwe Kleine-König authored
commit da6c2add upstream. To set the mux mode of a pin two bits must be set. Up to now this is implemented using the following idiom: writel(mask, reg + CLR); writel(value, reg + SET); . This however results in the mux mode being 0 between the two writes. On my machine there is an IC's reset pin connected to LCD_D20. The bootloader configures this pin as GPIO output-high (i.e. not holding the IC in reset). When Linux reconfigures the pin to GPIO the short time LCD_D20 is muxed as LCD_D20 instead of GPIO_1_20 is enough to confuse the connected IC. The same problem is present for the pin's drive strength setting which is reset to low drive strength before using the right value. So instead of relying on the hardware to modify the register setting using two writes implement the bit toggling using read-modify-write. Fixes: 17723111 ("pinctrl: add pinctrl-mxs support") Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> [bwh: Backported to 3.16: adjust filename, context] Signed-off-by:
-
Alexander Tsoy authored
commit 1fc2e41f upstream. This model is actually called 92XXM2-8 in Windows driver. But since pin configs for M22 and M28 are identical, just reuse M22 quirk. Fixes external microphone (tested) and probably docking station ports (not tested). Signed-off-by:
Alexander Tsoy <alexander@tsoy.me> Signed-off-by:
-
Gilad Ben-Yossef authored
commit f3ad5870 upstream. crypto_gcm_setkey() was using wait_for_completion_interruptible() to wait for completion of async crypto op but if a signal occurs it may return before DMA ops of HW crypto provider finish, thus corrupting the data buffer that is kfree'ed in this case. Resolve this by using wait_for_completion() instead. Reported-by:
Eric Biggers <ebiggers3@gmail.com> Signed-off-by:
Gilad Ben-Yossef <gilad@benyossef.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Michael Thalmeier authored
commit 0340ff83 upstream. ci_role BUGs when the role is >= CI_ROLE_END. Signed-off-by:
Michael Thalmeier <michael.thalmeier@hale.at> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Sebastian Reichel authored
commit 5165da59 upstream. Since v4.9 i2c-tiny-usb generates the below call trace and longer works, since it can't communicate with the USB device. The reason is, that since v4.9 the USB stack checks, that the buffer it should transfer is DMA capable. This was a requirement since v2.2 days, but it usually worked nevertheless. [ 17.504959] ------------[ cut here ]------------ [ 17.505488] WARNING: CPU: 0 PID: 93 at drivers/usb/core/hcd.c:1587 usb_hcd_map_urb_for_dma+0x37c/0x570 [ 17.506545] transfer buffer not dma capable [ 17.507022] Modules linked in: [ 17.507370] CPU: 0 PID: 93 Comm: i2cdetect Not tainted 4.11.0-rc8+ #10 [ 17.508103] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 [ 17.509039] Call Trace: [ 17.509320] ? dump_stack+0x5c/0x78 [ 17.509714] ? __warn+0xbe/0xe0 [ 17.510073] ? warn_slowpath_fmt+0x5a/0x80 [ 17.510532] ? nommu_map_sg+0xb0/0xb0 [ 17.510949] ? usb_hcd_map_urb_for_dma+0x37c/0x570 [ 17.511482] ? usb_hcd_submit_urb+0x336/0xab0 [ 17.511976] ? wait_for_completion_timeout+0x12f/0x1a0 [ 17.512549] ? wait_for_completion_timeout+0x65/0x1a0 [ 17.513125] ? usb_start_wait_urb+0x65/0x160 [ 17.513604] ? usb_control_msg+0xdc/0x130 [ 17.514061] ? usb_xfer+0xa4/0x2a0 [ 17.514445] ? __i2c_transfer+0x108/0x3c0 [ 17.514899] ? i2c_transfer+0x57/0xb0 [ 17.515310] ? i2c_smbus_xfer_emulated+0x12f/0x590 [ 17.515851] ? _raw_spin_unlock_irqrestore+0x11/0x20 [ 17.516408] ? i2c_smbus_xfer+0x125/0x330 [ 17.516876] ? i2c_smbus_xfer+0x125/0x330 [ 17.517329] ? i2cdev_ioctl_smbus+0x1c1/0x2b0 [ 17.517824] ? i2cdev_ioctl+0x75/0x1c0 [ 17.518248] ? do_vfs_ioctl+0x9f/0x600 [ 17.518671] ? vfs_write+0x144/0x190 [ 17.519078] ? SyS_ioctl+0x74/0x80 [ 17.519463] ? entry_SYSCALL_64_fastpath+0x1e/0xad [ 17.519959] ---[ end trace d047c04982f5ac50 ]--- Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.co.uk> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Till Harbaum <till@harbaum.org> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Konstantin Khlebnikov authored
commit 9651e6b2 upstream. I've got another report about breaking ext4 by ENOMEM error returned from ext4_mb_load_buddy() caused by memory shortage in memory cgroup. This time inside ext4_discard_preallocations(). This patch replaces ext4_error() with ext4_warning() where errors returned from ext4_mb_load_buddy() are not fatal and handled by caller: * ext4_mb_discard_group_preallocations() - called before generating ENOSPC, we'll try to discard other group or return ENOSPC into user-space. * ext4_trim_all_free() - just stop trimming and return ENOMEM from ioctl. Some callers cannot handle errors, thus __GFP_NOFAIL is used for them: * ext4_discard_preallocations() * ext4_mb_discard_lg_preallocations() Fixes: adb7ef60 ("ext4: use __GFP_NOFAIL in ext4_free_blocks()") Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Konstantin Khlebnikov authored
commit adb7ef60 upstream. This might be unexpected but pages allocated for sbi->s_buddy_cache are charged to current memory cgroup. So, GFP_NOFS allocation could fail if current task has been killed by OOM or if current memory cgroup has no free memory left. Block allocator cannot handle such failures here yet. Signed-off-by:
-
Konstantin Khlebnikov authored
commit 887a9730 upstream. ext4_expand_extra_isize() should clear only space between old and new size. Fixes: 6dd4ee7c # v2.6.23 Signed-off-by:
-
Jan Kara authored
commit 7d95eddf upstream. Currently, SEEK_HOLE implementation in ext4 may both return that there's a hole at some offset although that offset already has data and skip some holes during a search for the next hole. The first problem is demostrated by: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (2.054 GiB/sec and 538461.5385 ops/sec) Whence Result HOLE 0 Where we can see that SEEK_HOLE wrongly returned offset 0 as containing a hole although we have written data there. The second problem can be demonstrated by: xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k" -c "seek -h 0" file wrote 57344/57344 bytes at offset 0 56 KiB, 14 ops; 0.0000 sec (1.978 GiB/sec and 518518.5185 ops/sec) wrote 8192/8192 bytes at offset 131072 8 KiB, 2 ops; 0.0000 sec (2 GiB/sec and 500000.0000 ops/sec) Whence Result HOLE 139264 Where we can see that hole at offsets 56k..128k has been ignored by the SEEK_HOLE call. The underlying problem is in the ext4_find_unwritten_pgoff() which is just buggy. In some cases it fails to update returned offset when it finds a hole (when no pages are found or when the first found page has higher index than expected), in some cases conditions for detecting hole are just missing (we fail to detect a situation where indices of returned pages are not contiguous). Fix ext4_find_unwritten_pgoff() to properly detect non-contiguous page indices and also handle all cases where we got less pages then expected in one place and handle it properly there. Fixes: c8c0df24 CC: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by:
-
Al Viro authored
commit a8c39544 upstream. failing sys_wait4() won't fill struct rusage... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Radim Krčmář authored
commit f0367ee1 upstream. Static checker noticed that base3 could be used uninitialized if the segment was not present (useable). Random stack values probably would not pass VMCS entry checks. Reported-by:
Paolo Bonzini <pbonzini@redhat.com> Reviewed-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Wanpeng Li authored
commit cbfc6c91 upstream. Huawei folks reported a read out-of-bounds vulnerability in kvm pio emulation. - "inb" instruction to access PIT Mod/Command register (ioport 0x43, write only, a read should be ignored) in guest can get a random number. - "rep insb" instruction to access PIT register port 0x43 can control memcpy() in emulator_pio_in_emulated() to copy max 0x400 bytes but only read 1 bytes, which will disclose the unimportant kernel memory in host but no crash. The similar test program below can reproduce the read out-of-bounds vulnerability: void hexdump(void *mem, unsigned int len) { unsigned int i, j; for(i = 0; i < len + ((len % HEXDUMP_COLS) ? (HEXDUMP_COLS - len % HEXDUMP_COLS) : 0); i++) { /* print offset */ if(i % HEXDUMP_COLS == 0) { printf("0x%06x: ", i); } /* print hex data */ if(i < len) { printf("%02x ", 0xFF & ((char*)mem)[i]); } else /* end of block, just aligning for ASCII dump */ { printf(" "); } /* print ASCII dump */ if(i % HEXDUMP_COLS == (HEXDUMP_COLS - 1)) { for(j = i - (HEXDUMP_COLS - 1); j <= i; j++) { if(j >= len) /* end of block, not really printing */ { putchar(' '); } else if(isprint(((char*)mem)[j])) /* printable char */ { putchar(0xFF & ((char*)mem)[j]); } else /* other char */ { putchar('.'); } } putchar('\n'); } } } int main(void) { int i; if (iopl(3)) { err(1, "set iopl unsuccessfully\n"); return -1; } static char buf[0x40]; /* test ioport 0x40,0x41,0x42,0x43,0x44,0x45 */ memset(buf, 0xab, sizeof(buf)); asm volatile("push %rdi;"); asm volatile("mov %0, %%rdi;"::"q"(buf)); asm volatile ("mov $0x40, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x41, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x42, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x43, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x44, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("mov $0x45, %rdx;"); asm volatile ("in %dx,%al;"); asm volatile ("stosb;"); asm volatile ("pop %rdi;"); hexdump(buf, 0x40); printf("\n"); /* ins port 0x40 */ memset(buf, 0xab, sizeof(buf)); asm volatile("push %rdi;"); asm volatile("mov %0, %%rdi;"::"q"(buf)); asm volatile ("mov $0x20, %rcx;"); asm volatile ("mov $0x40, %rdx;"); asm volatile ("rep insb;"); asm volatile ("pop %rdi;"); hexdump(buf, 0x40); printf("\n"); /* ins port 0x43 */ memset(buf, 0xab, sizeof(buf)); asm volatile("push %rdi;"); asm volatile("mov %0, %%rdi;"::"q"(buf)); asm volatile ("mov $0x20, %rcx;"); asm volatile ("mov $0x43, %rdx;"); asm volatile ("rep insb;"); asm volatile ("pop %rdi;"); hexdump(buf, 0x40); printf("\n"); return 0; } The vcpu->arch.pio_data buffer is used by both in/out instrutions emulation w/o clear after using which results in some random datas are left over in the buffer. Guest reads port 0x43 will be ignored since it is write only, however, the function kernel_pio() can't distigush this ignore from successfully reads data from device's ioport. There is no new data fill the buffer from port 0x43, however, emulator_pio_in_emulated() will copy the stale data in the buffer to the guest unconditionally. This patch fixes it by clearing the buffer before in instruction emulation to avoid to grant guest the stale data in the buffer. In addition, string I/O is not supported for in kernel device. So there is no iteration to read ioport %RCX times for string I/O. The function kernel_pio() just reads one round, and then copy the io size * %RCX to the guest unconditionally, actually it copies the one round ioport data w/ other random datas which are left over in the vcpu->arch.pio_data buffer to the guest. This patch fixes it by introducing the string I/O support for in kernel device in order to grant the right ioport datas to the guest. Before the patch: 0x000000: fe 38 93 93 ff ff ab ab .8...... 0x000008: ab ab ab ab ab ab ab ab ........ 0x000010: ab ab ab ab ab ab ab ab ........ 0x000018: ab ab ab ab ab ab ab ab ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: f6 00 00 00 00 00 00 00 ........ 0x000008: 00 00 00 00 00 00 00 00 ........ 0x000010: 00 00 00 00 4d 51 30 30 ....MQ00 0x000018: 30 30 20 33 20 20 20 20 00 3 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: f6 00 00 00 00 00 00 00 ........ 0x000008: 00 00 00 00 00 00 00 00 ........ 0x000010: 00 00 00 00 4d 51 30 30 ....MQ00 0x000018: 30 30 20 33 20 20 20 20 00 3 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ After the patch: 0x000000: 1e 02 f8 00 ff ff ab ab ........ 0x000008: ab ab ab ab ab ab ab ab ........ 0x000010: ab ab ab ab ab ab ab ab ........ 0x000018: ab ab ab ab ab ab ab ab ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: d2 e2 d2 df d2 db d2 d7 ........ 0x000008: d2 d3 d2 cf d2 cb d2 c7 ........ 0x000010: d2 c4 d2 c0 d2 bc d2 b8 ........ 0x000018: d2 b4 d2 b0 d2 ac d2 a8 ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ 0x000000: 00 00 00 00 00 00 00 00 ........ 0x000008: 00 00 00 00 00 00 00 00 ........ 0x000010: 00 00 00 00 00 00 00 00 ........ 0x000018: 00 00 00 00 00 00 00 00 ........ 0x000020: ab ab ab ab ab ab ab ab ........ 0x000028: ab ab ab ab ab ab ab ab ........ 0x000030: ab ab ab ab ab ab ab ab ........ 0x000038: ab ab ab ab ab ab ab ab ........ Reported-by:
Moguofang <moguofang@huawei.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Moguofang <moguofang@huawei.com> Signed-off-by:
Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by:
-
Sven Eckelmann authored
commit 36d4d68c upstream. The stats are generated by batadv_interface_stats and must not be stored directly in the net_device stats member variable. The batadv_priv bat_counters information is assembled when ndo_get_stats is called. The stats previously stored in net_device::stats is then overwritten. The batman-adv counters must therefore be increased when an ARP packet is answered locally via the distributed arp table. Fixes: c384ea3e ("batman-adv: Distributed ARP Table - add snooping functions for ARP messages") Signed-off-by:
Sven Eckelmann <sven@narfation.org> Signed-off-by:
Simon Wunderlich <sw@simonwunderlich.de> [bwh: Backported to 3.16: adjust context] Signed-off-by:
-
