Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

If we receive an L2CAP command reject message over LE we should take
appropriate action on the corresponding channel. This is particularly
important when trying to interact with a remote pre-4.1 system using LE
CoC signaling messages. If we don't react to the command reject the
corresponding socket would not be notified until a connection timeout
occurs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The internal regulator needs to be programmed
correctly for AR955x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Adjusting the CCA registers for maximum permissible
noise floor in ETSI/Japan domains has to be done for
all AR9003 family chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Now that the Buffalo-specific initvals have been
moved to a separate array, update the default high
power TX gain table for all AR9300 v2.2 devices.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.

By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.

The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

* Update radio/baseband/gain tables.
* Mark ar9331_modes_high_power_tx_gain_1p1 as a duplicate
* ar9331_1p1_mac_postamble is not a duplicate.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable the ALWAYS_KEYSEARCH bit in the initvals. Currently
this is done in the driver, but adding this to the initvals
makes it easier to be in sync with the INI files given
by the systems engineering team.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Certain baseband registers require different values
to be programmed when operating in a DFS channel to
ensure that radar detection works correctly. This
is required for AR9300, AR9340 and AR9580.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sparse reports the following:

  CHECK   drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c:570:34: warning: dubious: !x & y

There should be a parens around the expression.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable the beaconing in wnc36xx by tweaking the tim offset and
force the use of AP-style beaconing. Otherwise, beaconing is not
working. The tim offset is set to 256. Otherwise, this will
overwrite mesh beacon submitted by mac80211.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When TX data URB reaches high water mark the message
"data: -ENOSR is returned" is printed.
This is not an error case, so change it to debug print.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The check for 'priv' pointer is redundant. 'priv' won't
be used later in this routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The bridged packets are updated to statistics on both TX and RX
paths. Also fix a typo in the comment.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The skb is modified in sending the TX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The skb is modified in processing the RX packet. Save the original
packet length to a variable so that we can get the correct
statistics update.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

RX packets are handled in different paths. Not all paths have
decrement of rx_pending counter. This patch fixes the counter
imbalance.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

eth_hdr is defined in kernel. Use a different variable name in
our functions.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

SNAP/LLC header in the AARP packet is being stripped off while
preparing an EthernetII header.
Annex M, Table M.3 in 802.11 spec says that some header
(ex. AppleTalk AARP(2)) should pass through untouched.
This patch modifies the check to exclude/include EthernetII
header translation for special cases.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use 'rfc1042_header' available in net/wireless/util.c
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Actually we are updating snap_type with h_proto (__be16 variable)
in ethernet frame header. Hence endianness conversion is not
required.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware expects the command structure members in little
endianness.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Conflicts:
	drivers/net/wireless/ath/ath10k/htc.c
	drivers/net/wireless/ath/ath10k/mac.c

This fixes compilation issues with CONFIG_MAC80211_DEBUGFS
not enabled.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Sync to SCO is a feature that allows to synchronise the
wifi activity with the predictable BT activity in
SCO profile. This allows to reduce the collisions and
improve overall quality.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Rewrite the search cycle state machine to use a more data
oriented approach where the different Tx columns (configs)
limitations and next columns to search are reprsented in
tables which are easy to change. This overhaul also includes
several major fixes:

1. Prevent going back to a specific Tx column in a search
cycle if it was already explored.

2. Avoid switching to a Tx column that doesn't have any chance
if it performs perfectly to beat the current throughput we're
getting.

These issues were degrading throughput as they were causing
switching to "bad" Tx columns.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use the 20Mhz channel width define instead of just the number
zero for legacy rates. Note that the define has the same value
so this is just a minor cleanup.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>