A patch to change to page accounting code (in v4.8-rc1) conflicts with
a change to lustre (in staging-next for v4.9), and fortunately gets
detected using a gcc warning:

In file included from /git/arm-soc/include/linux/mm.h:1001:0,
                 from /git/arm-soc/include/linux/highmem.h:7,
                 from /git/arm-soc/drivers/staging/lustre/lustre/osc/../../include/linux/libcfs/linux/libcfs.h:46,
                 from /git/arm-soc/drivers/staging/lustre/lustre/osc/../../include/linux/libcfs/libcfs.h:36,
                 from /git/arm-soc/drivers/staging/lustre/lustre/osc/osc_cl_internal.h:45,
                 from /git/arm-soc/drivers/staging/lustre/lustre/osc/osc_page.c:40:
drivers/staging/lustre/lustre/osc/osc_page.c: In function 'unstable_page_accounting':
include/linux/vmstat.h:117:2: error: array subscript is above array bounds [-Werror=array-bounds]
  atomic_long_add(x, &vm_zone_stat[item]);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/vmstat.h:117:2: error: array subscript is above array bounds [-Werror=array-bounds]
  atomic_long_add(x, &vm_zone_stat[item]);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

This changes the function to use the correct interface for accounting in the
"node" rather than the "zone".
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d806f30e ("staging: lustre: osc: revise unstable pages accounting")
Fixes: 11fb9989 ("mm: move most file-based accounting to the node")
Reviewed-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently it is not possible to send LNet traffic between
two nodes using infiniband hardware that have different
page sizes for the case when RDMA fragments are used.
When two nodes establish a connection they tell the other
node the maximum number of RDMA fragments they support.
The issue is that the units are pages, and 256 64K pages
corresponds to 16MB of data, whereas a 4K page system is
limited to messages with 1MB of data. The solution is to
report over the wire the maximum number of fragments in
4K unites regardless of the native page size. The recipient
then uses its native page size to translate into the
maximum number of pages sized fragments it can send to
the other node.
Signed-off-by: James Simmons <uja.ornl@yahoo.com>
Reviewed-on: http://review.whamcloud.com/21304
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7650Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Olaf Weber <olaf@sgi.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In lustre_fill_super() if lustre_start_mgc() fails then call
lustre_common_put_super() to release a reference on the MGC device
attached to the LSI.
Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/20851
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8297Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Reviewed-by: Mike Pershin <mike.pershin@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ll_find_alias is responsible for getting alias for inode
which can be reused. Directories are assumed to have unique
alias, where in case of non-directories there can be multiple
aliases. In case of lustre there can be two type of aliases
i.e. discon_alias and invalid_alias. Usage of discon_alias in
case of non-directories may corrupt dcache and leads to kernel
crash. Changes made to avoid use of discon_alias in case of
non-directories.

Seagate-bug-id: MRP-2739, MRP-3601
Signed-off-by: Lokesh Nagappa Jaliminche <lokesh.jaliminche@seagate.com>
Reviewed-by: Ujjwal Lanjewar <ujjwal.lanjewar@seagate.com>
Reviewed-by: Ashish Purkar <ashish.purkar@seagate.com>
Reviewed-by: Andrew Perepechko <andrew.perepechko@seagate.com>
Tested-by: Parinay Vijayprakash Kondekar <parinay.kondekar@seagate.com>
Reviewed-on: http://review.whamcloud.com/17732
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7613Reviewed-by: Niu Yawei <yawei.niu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove useless LASSERT(vma->vm_file) because of if it's NULL it
will crash early in file_inode(vma->vm_file).
Signed-off-by: Dmitry Eremin <dmitry.eremin@intel.com>
Reviewed-on: http://review.whamcloud.com/21171
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8372Reviewed-by: John L. Hammond <john.hammond@intel.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The return value is ignored in client_common_fill_super.
Restore to check it and error out.
Signed-off-by: Yang Sheng <yang.sheng@intel.com>
Reviewed-on: http://review.whamcloud.com/21125
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-8360Reviewed-by: Emoly Liu <emoly.liu@intel.com>
Reviewed-by: Bob Glossman <bob.glossman@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The patch removes find_cbdata callbacks and clear_nlink
from dentry_iput path, since this piece of code makes
a few races possible.

The test case reproduces one of the possible races
described in LU-7925:

1) two hard links are created for the same file
2) the test calls stat(2) for link #1
3) in the middle of 2) the test opens and closes link #2
4) in the middle of 2) the test drops the ldlm locks and
   forces dentry reclaim via vm.drop_caches=2
5) in the middle of 2) ll_d_iput() clears i_nlink for
   the inode
6) the initial stat(2) continues and copies the wrong
   i_nlink value into st_nlink
Signed-off-by: Andrew Perepechko <andrew.perepechko@seagate.com>
Seagate-bug-id: MRP-3271
Reviewed-on: http://review.whamcloud.com/19164
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7925Reviewed-by: Wally Wang <wang@cray.com>
Reviewed-by: Lai Siyao <lai.siyao@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Assertion was happened for open request when rq_replay is set
to 1.
    ASSERTION(mod->mod_open_req->rq_replay == 0)
But this situation is not fatal for client, and could happened
when mdc_close() failed.
The fix allow to free such requests. If mdc_close fail, MDS doesn`t
receive close request from client. And in a worst case client would
be evicted.

The test recreates issue when mdc_close failed and
client asserts:
   ASSERTION( mod->mod_open_req->rq_replay == 0 ) failed
Signed-off-by: Alexander Boyko <alexander.boyko@seagate.com>
Seagate-bug-id: MRP-3156
Reviewed-on: http://review.whamcloud.com/17495
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-5282Reviewed-by: Alex Zhuravlev <alexey.zhuravlev@intel.com>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change the __u64 *cookie parameter of md_ops->set_lock_data() to
const struct lustre_handle *lockh.
Signed-off-by: John L. Hammond <john.hammond@intel.com>
Reviewed-on: http://review.whamcloud.com/17072
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-7403Reviewed-by: Frank Zago <fzago@cray.com>
Reviewed-by: James Simmons <uja.ornl@yahoo.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dgnc_maxcps_room() function must be called only for print device.
The if-statement for checking print device checks before calling
dgnc_maxcps_room() and also this function doesn't need to have any
data except channel_t.
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpath.pl warning:
trailing statements should be on next line
open brace '{' following function declarations go on the next line
Signed-off-by: Anson Jacob <ansonjacob.aj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparse was warning about incorrect type of argument:

drivers/staging/i4l/icn/icn.c:1048:49: warning: incorrect type in argument 2 (different address spaces)
drivers/staging/i4l/icn/icn.c:1048:49: expected void const [noderef] <asn:1>*from
drivers/staging/i4l/icn/icn.c:1048:49: got unsigned char const [usertype] *buf
drivers/staging/i4l/icn/icn.c:1476:38: warning: incorrect type in argument 1 (different address spaces)
drivers/staging/i4l/icn/icn.c:1476:38: expected unsigned char const [usertype] *buf
drivers/staging/i4l/icn/icn.c:1476:38: got unsigned char const [noderef] [usertype] <asn:1>*buf

The function icn_writecmd() was used to copy from userspace and also
from the kernelspace. Add another argument to the function to have two
separate pointers, one for the userspace and one for the kernelspace.
Based on the value of user as passed from the caller we use one of
the two pointers.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Blank lines are not needed after starting brace or before a closing
brace.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No need provide a space after a typecast.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The macro EVAL_PLCI and MAKE_PLCI are not being used. Remove them.
But keep the comment preceding them as it contains information
regarding message format.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The macro EVAL_NCCI was only being used in capi.c and the argument
controller was not used. Remove the argument and at the same time
remove the variable which now becomes unused.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Its better to use memdup_user which does the same thing which this
code has implemented. Also removed a related warning as we will be
warned if allocation fails.
Suggested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch.pl warning for line over 80 characters
Signed-off-by: Anson Jacob <ansonjacob.aj@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The module name in the Makefile and in the driver source file is
octeon-hcd, so correct the Kconfig text to be the same.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.9a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-testing

Jonathan writes:

First round of new features, device support and cleanups for IIO in the 4.9 cycle.

Device support

* ak8974
  - New driver and bindings for this 2009 vintage magnetometer (it was very
    popular back then!)
* atlas-ph-sensor
  -  ORP sensor support(I had to look up what one of these was)
* cio-dac
  - New driver for Measurement Computing DAC boards
* dmard06
  - New driver for Domintech DMARDO6 accelerometer. Also vendor prefix.
* dmard09
  - New driver for Domintech DMARD09 accelerometer.
* maxim-thermocouple
  - max6675 and max31855 new driver
* mt6577 auxdac
  - new driver for this Mediatek chip mt2701, mt6577 and mt8173 have this
    hardware.
* ti-adc161s626
  - new driver for this TI single channel differential ADC.
* vcnl4000
  - support vcnl4010 and vcnl4020 which are compatible for all features
    currently supported by this driver.

New features

* Core
  - Allow retrieving of underlying iio_dev from a callback buffer handle.
    This is needed to allow client drivers to perform operations such as
    configuring the trigger used.
* hid-sensors
  - asynchronous resume support to avoid really long resume times.
* kxcjk-1013
  - add the mysterious KIOX000A ACPI id seen in the wild.
* Tools
  - lsiio now enumerates processed as well as raw channels.

Cleanup

* ad7298
  - use iio_device_claim_direct_mode and friends to simplify locking around
    mode switching and drop some boilerplate.
* ad7793
  - use iio_device_claim_direct_mode and friends to simplify locking around
    mode switching and drop some boilerplate.
* ade7854
  - checkpatch fixups (alignment of parameters)
* atlas-ph-sensor
  - use iio_device_claim_direct_mode and friends to simplify locking around
    mode switching and drop some boilerplate.
  - Switch to REGCACHE_NONE as there are no useful register to cache.
* bma180
  - use iio_device_claim_direct_mode and friends to simplify locking around
    mode switching and drop some boilerplate.
* hdc100x
  - Add mention of the HDC1000 and HDC1008 to the Kconfig help text.
* isl29018
  - Add driver specific prefixes to defines and function names.
  - Remove excessive logging.
  - Drop newlines which add nothing to readability.
  - General tidying up of comments.
  - Drop I2C_CLASS_HWMON as irrelevant to driver.
* isl29028
  - Add driver specific prefixes to defines, enums and function names.
  - Drop comma's from available attribute output as not ABI compliant.
  - Drop I2C_CLASS_HWMON as irrelevant to driver.
* kxsd9
  - devicetree bindings.
* mag3110
  - This one wasn't locking to protect against mode switches during
    raw_reads.  Use the iio_claim_direct_mode function to fix this buglet.
* maxim-theromcouple
  - Fix missing selects for triggered buffer support in Kconfig.
* nau7802
  - Use complete instead of complete_all as only one completion at a time.
* sx9500
  - Use complete instead of complete_all as only one completion at a time.
* us5182d
  - Add a missing error code asignment instead of checking the result of
    an already checked statement.
* vcnl4000
  - Use BIT macro where appropriate.
  - Refactor return codes in read_raw callback.
  - Add some missing locking for concurrent accesses to the device.

This patch is needed to clean up the initialized ida structure in case
the function exits with an exception.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function mdc_adjust_dirpages is only called on platforms which
don't have pages 4K in size which is why kbuild only reported this
for platforms like the Alpha. The problem was a typo in ordering of
variables in the beginning of a while loop. We were accessing the
dp pointer before it was kmapped.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cp_error member is not really set anywhere, so kill
it and the only printing user of it too.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes most of checkpatch occurences of
"CHECK: Alignment should match open parenthesis"
in Lustre code.
Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes all checkpatch occurences of
"CHECK: spaces preferred around that '{+,-,*,/,|,<<,>>,&}' (ctx:VxV)"
in Lustre code.
Signed-off-by: Emoly Liu <emoly.liu@intel.com>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This accelerometer can be probed from the device tree, so it needs
to have proper documentation of it's device tree bindings.

Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Some platforms power off sensor hubs during S3 suspend, which will require
longer time to resume. This hurts system resume time, so resume
asynchronously.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Add Mediatek auxadc driver based on iio.
It will register a device in iio and support iio.
So thermal can read auxadc channel to sample data by iio device.
It is tested successfully on mt2701 platform.
Mt8173 and mt6577 platforms are not tested.
But the expectation is compatible.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The commit adds the device tree binding documentation for the mediatek
auxadc found on Mediatek MT2701.
Thermal gets auxadc sample data by iio device.
So the commit changes auxadc device tree binding documentation from
/soc/mediatek/auxadc.txt to /iio/adc/mt6577_auxadc.txt.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Select IIO_BUFFER and IIO_TRIGGERED_BUFFER to compile maxim_thermocouple.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Driver was checking for direct mode but not locking it.  Use
claim/release helper functions to guarantee the device stays
in direct mode during raw reads.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch fixes a minor checkpatch warning:

"WARNING: Prefer 'unsigned int' to bare use of 'unsigned'"
Signed-off-by: Louie Lu <louie.lu@hopebaytech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mg_get_local_EKB and mg_get_ICV used to return with an error code before
releasing all resources. This patch add a jump to the appropriate label
ensuring that the resources are properly released before returning.

This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch changes label names using camel case to snake case as well as giving
a new name representing what will be done after the label.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a patch for double blank lines and a missing blank line reported
by checkpatch.pl
Signed-off-by: Jonas Rickert <jrickertkc@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed spaces around operators to fix their coding style issues.
Signed-off-by: Shiva Kerdel <shiva@exdev.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

BT_Active and BT_State are being masked with 0x00ffffff so it the subsequent
comparisons with 0xffffffff are therefore a buggy check.  Instead, check them
against 0x00ffffff.

Unfortunately I couldn't find a datasheet or hardware to see if 0xffffffff
is an expected invalid bit pattern that should be checked before BT_Active and
BT_State are masked with 0x00ffffff, so for now, this fix seems like the least
risky approach.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig currently controlling compilation of this code is:

config FSL_MC_BUS
        bool "Freescale Management Complex (MC) bus driver"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since the code was already not using module_init, we don't have to change
the initcall and the init ordering remains unchanged with this commit.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

We don't replace module.h with init.h since the file does make some
references to "struct *module" for processing other modules.

Cc: "J. German Rivera" <German.Rivera@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a helper macro to return if a device has a bus type of fsl_mc.
This makes the bus driver code more readable and provides a way for
drivers like the SMMU driver to easily check the bus type.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Acked-by: Stuart Yoder <stuart.yoder@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The semaphores xmit_sema, terminate_xmitthread_sema, tx_retevt and
io_req have no users, hence remove all references to them.
Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>