- 22 Aug, 2011 24 commits
-
-
Dong Aisheng authored
Signed-off-by:
Dong Aisheng <b29396@freescale.com> Acked-by:
Liam Girdwood <lrg@ti.com> Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com>
-
Julia Lawall authored
Move the test on pdev->id before the kzalloc to avoid requiring kfree when the test fails. This fix was suggested by Wolfram Sang. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier x; expression E1!=0,E2,E3,E4; statement S; iterator I; @@ ( if (...) { ... when != kfree(x) when != x = E3 when != E3 = x * return ...; } ... when != x = E2 when != I(...,x,...) S if (...) { ... when != x = E4 kfree(x); ... return ...; } ) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
Wolfram Sang <w.sang@pengutronix.de> Acked-by:
-
Dong Aisheng authored
Saif needs clear clk gate first before writing registers or the write will not success. The original xx_get_mclk function clear clk gate after mclk setting that may cause the former mclk setting unwork, then the real output mclk maybe inaccurate. Placing the clear before setting mclk to avoid such an issue. We also have to clear clk gate in startup instead of in prepare function. Signed-off-by:
-
Mark Brown authored
-
Julia Lawall authored
The first change is to add an of_node_put, since codec_np has previously been allocated. The rest of the patch reorganizes the error handling code so the only code executed is that which is needed. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier x; expression E1!=0,E2,E3,E4; statement S; iterator I; @@ ( if (...) { ... when != of_node_put(x) when != x = E3 when != E3 = x * return ...; } ... when != x = E2 when != I(...,x,...) S if (...) { ... when != x = E4 of_node_put(x); ... return ...; } ) // </smpl> Signed-off-by:
Timur Tabi <timur@freescale.com> Acked-by:
-
Julia Lawall authored
dma_channel_np has been accessed at this point, so decrease its reference count before leaving the function. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier x; expression E1!=0,E2,E3,E4; statement S; iterator I; @@ ( if (...) { ... when != of_node_put(x) when != x = E3 when != E3 = x * return ...; } ... when != x = E2 when != I(...,x,...) S if (...) { ... when != x = E4 of_node_put(x); ... return ...; } ) // </smpl> Signed-off-by:
-
Julia Lawall authored
Introduce a new label that includes kfree and jump to that one. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier x; expression E1!=0,E2,E3,E4; statement S; iterator I; @@ ( if (...) { ... when != kfree(x) when != x = E3 when != E3 = x * return ...; } ... when != x = E2 when != I(...,x,...) S if (...) { ... when != x = E4 kfree(x); ... return ...; } ) // </smpl> Signed-off-by:
Alexander Sverdlin <subaparts@yandex.ru> Reviewed-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by:
-
Julia Lawall authored
Adjust the goto to jump to the error handling code that includes kfree. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ identifier x; expression E1!=0,E2,E3,E4; statement S; iterator I; @@ ( if (...) { ... when != kfree(x) when != x = E3 when != E3 = x * return ...; } ... when != x = E2 when != I(...,x,...) S if (...) { ... when != x = E4 kfree(x); ... return ...; } ) // </smpl> Signed-off-by:
-
Axel Lin authored
GFP_ATOMIC is not needed here, use GFP_KERNEL instead. Signed-off-by:
Axel Lin <axel.lin@gmail.com> Acked-by:
-
Timur Tabi authored
of_parse_phandle increments the reference count of np, so this should be decremented before trying the next possibility. Since we don't actually use np, we can decrement the reference count immediately. Reported-by:
-
Mark Brown authored
If devices can unconditionally support idle_bias_off let them flag it in their driver structure. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
-
Mark Brown authored
In case we have a pending completion, for example due to a problem with the input clock which got corrected after we timed out. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
Ensure that we don't spuriously trigger early. Signed-off-by:
-
Mark Brown authored
This should never happen with level triggered IRQs. Signed-off-by:
-
Mark Brown authored
The WM8962 features a DSP providing a number of signal processing features including HD Bass and Virtual Surround Sound (VSS). Enable initial support for this, allowing users to enable and disable the algorithms using the default coefficient sets. Further patches will add support for runtime configuration of the DSP coefficients. Signed-off-by:
-
Mark Brown authored
We get called once per DAPM context but only need to run once. When DAPM was serialized this was a series of noops but now it can run in parallel we need to take proper care. Signed-off-by:
-
Mark Brown authored
Signed-off-by:
-
Mark Brown authored
This occurs frequently if we are in edge triggered mode as we must poll the interrupt status register until we get no more interrupts so it's worth the effort - it means we skip writing null acknowledgements to the chip. Signed-off-by:
-
Mark Brown authored
For non-audio uses like accessory detection we can use a lower quality, unregulated microphone bias, saving a little power. As the hardware can manually enable and disable the biases we can select regulating mode automatically with supply widgets connected to the biases. Signed-off-by:
-
Mark Brown authored
There's no need for separate widgets for the enables (as the map already shows). Signed-off-by:
-
Mark Brown authored
Make AIFCLK supply the record paths otherwise record will not work unless there is a simultaneous playback. Signed-off-by:
-
- 18 Aug, 2011 3 commits
-
-
Axel Lin authored
This patch includes below small fixes: 1. Move sta32x_set_bias_level() from sta32x_i2c_remove() to sta32x_remove(). 2. Remove a redundant regulator_bulk_free() call in sta32x_i2c_remove(), as we will call regulator_bulk_free() in sta32x_remove(). 3. Remove unneeded snd_soc_codec_set_drvdata(codec, NULL) in sta32x_i2c_remove. The i2c core will set the clientdata to NULL. Signed-off-by:
-
Mark Brown authored
-
Jarkko Nikula authored
Fix "error: too few arguments to function 'ams_delta_set_bias_level'" build errors in ams-delta.c that were introduced after commit d4c6005f ("ASoC: Add context parameter to card DAPM callbacks") by adding dapm context to ams_delta_set_bias_level calls. Signed-off-by:
Jarkko Nikula <jarkko.nikula@bitmer.com> Acked-by:
-
- 17 Aug, 2011 6 commits
-
-
Mark Brown authored
-
Axel Lin authored
Signed-off-by:
-
Sascha Hauer authored
The ASoC core tries to not enforce symmetric rates when two streams open simultaneously. It does so by checking rtd->rate being zero. This works exactly once after booting because it is not set to zero again when the streams close. Fix this by setting rtd->rate when no active stream is left. [This leads to lots of warnings about not enforcing the symmetry in some situations as there's a race in the userspace API where we know we've got two applications but don't know what rates they want to set. -- broonie ] Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Timur Tabi authored
The previous patch to fsl_dma.c ("fix initialization of DMA buffers") left behind an unused local variable that causes a build warning. Signed-off-by: -
Mark Brown authored
Signed-off-by:
Stephen Rothwell <sfr@canb.auug.org.au>
-
Timur Tabi authored
The PowerPC Freescale SSI driver is claiming the IRQ when the IRQ when the device is opened, which means that the /proc/interrupts entry for the SSI exists only during playback or capture. This also meant that the user won't know that the IRQ number is wrong until he tries to use the device. Instead, we should claim the IRQ when the device is probed. Signed-off-by:
-
- 16 Aug, 2011 5 commits
-
-
Lars-Peter Clausen authored
Add a machine driver to support the EVAL-ADAU1373 board connected to a Analog Devices BF5XX evaluation board. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Lars-Peter Clausen authored
This patch adds support for the Analog Devices ADAU1373 audio codec. Signed-off-by:
-
Mark Brown authored
ALSA doesn't really have good mechanisms for dealing with these so we just log them - the hardware already has automatic shutdown support. Signed-off-by: -
Mark Brown authored
Signed-off-by: -
Mark Brown authored
Ensure we have access to all the advanced DSP functinality offered by the WM8962 by running the system clock at 512fs. Signed-off-by:
-
- 15 Aug, 2011 2 commits
-
-
Lars-Peter Clausen authored
Currently it is only possible to route one source per switch into a mixer. This patch modifies the code, so that it is possible to route multiple sources into a mixer via the same switch. One use-case for this is routing a stereo channel pair into a mono-mixer via the same switch. Signed-off-by:
-
Mark Brown authored
Pull control is availalbe for WM8994 AIF2, generally disabled as part of the GPIO configuration in order to save power after system startup. As on newer devices in the series there is no GPIO functionality on these pins this will happen less naturally so have the driver disable the pulls as the AIF is probed. Signed-off-by:
-
