use %pM and %ph specifiers instead of placing each byte on stack.
(staging/rtl8723au/TODO)
Signed-off-by: Daniil Leshchev <meleodr@gmail.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Previosly the function had the following prototype:
int rtl8723a_set_rssi_cmd(struct rtw_adapter *padapter, u8 *param)

My suggestion here is to modify the prototype this way:
int rtl8723a_set_rssi_cmd(struct rtw_adapter *padapter, u32 param)

We can do this based on the following considerations:
1. rtl8723a_set_rssi_cmd is used only with 32-bit "param" values
2. There's no point in using "u8 *param" until we pass param length
3. As we just read "param", it's ok to pass it by value
Signed-off-by: Anatoly Stepanov <drivengroove@gmail.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed four spelling errors.
Signed-off-by: Jiading Gai <jiading.gai.github@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

That patch adds support for SSD1325 controller.
That is 4bpp grayscale OLED display controller present in several
displays eq: Winstar WEX012864
Signed-off-by: Alexey Mednyy <swexru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

That patch adds support for SSD1305 controller.
That is monochrome OLED display controller present in several
displays eq: Winstar WEX012864
Signed-off-by: Alexey Mednyy <swexru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use to_spi_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of duplicate defines from the headers.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch makes use of the standard MIPI Display Command Set to remove
some of the magic constants found in source code.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Deleted various commented out lines that have been replaced by write_reg()
Signed-off-by: Ben Gilbert <gillie59978@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver core clears the driver data to NULL after device_release
or on probe failure.
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rewrite multiple comparisons to NULL as "!fifo->data"
to fix the last coding style problems of this file.
Signed-off-by: Christian Colic <colic.christian@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This fixes all "No space is necessary after a cast" messages
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Removed blank line after curly braces.
Found using checkpatch.pl.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixed coding style warnings related to comment blocks
Signed-off-by: Saatvik Arya <aryasaatvik@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Only wake tx queue when driver queue is back within bounds.

The logic here was just reenabling the queue when any buffers had been
freed.  the queue was stopped whenever the length exceeded 1000
(MAX_OUT_QUEUE_DEPTH), but then was essentially immediately started again.
On a congested link, the queue length would just keep increasing up to
around 8000 (for average size packets), at which point the hardware would
start refusing the packets and they would begin to be dropped.
This prevented the qdisc layer from effectively managing and prioritising
packets, as essentially all packets were being allowed into the driver
queue and then were being dropped by the hardware.

This change only restarts the queue if the length is less than 1000
(MAX_OUT_QUEUE_DEPTH).
Reviewed-by: Kyeong Yoo <kyeong.yoo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the network portion of a frame is preceded by more than 14 bytes of
data, the checksum calculated in the HW is done over the wrong data and
is put in the wrong place.
In our use case an Octeon ethernet controller is connected to a Broadcom
switch chip. Extra data is included in the frame prior to egressing the
Octeon ethernet (i.e. 4 bytes of an 802.1Q tag, 4 bytes of a proprietary
BCM tag later stripped by the switch chip). This extra data causes the
checksum calculation to be incorrect.
The fix in this patch is to make use of the network header offset of the
skb. This enables the checksum to be calculated correctly.
This has been tested in both the configuration with the switch chip in
the egress path (as described above) and in a simple connection direct
to the wire.
Reviewed-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Reviewed-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Initialize/Cleanup ITS-MSI support for the MC bus driver at driver
init/exit time. Associate an MSI domain with each DPAA2 child device.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The interrupt handler for DPRC IRQs is added. DPRC IRQs are
generated for hot plug events related to DPAA2 objects in a given
DPRC. These events include, creating/destroying DPAA2 objects in
the DPRC, changing the "plugged" state of DPAA2 objects and moving
objects between DPRCs.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Destroy mc_io in error path in dprc_probe() only if the mc_io was
created in this function.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

THE MSI domain associated with a root DPRC object is
obtained form the device tree. Child DPRCs inherit
the parent DPRC MSI domain.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Scan the corresponding DPRC container to get total count
of IRQs needed by all its child DPAA2 objects. Then,
preallocate a set of MSI IRQs with the DPRC's ICID
(GIT-ITS device Id) to populate the the DPRC's IRQ pool.
Each child DPAA2 object in the DPRC and the DPRC object itself
will allocate their necessary MSI IRQs from the DPRC's IRQ pool,
in their driver probe function.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The DPRC built-in portal's mc_io is used to send commands to the MC
to program MSIs for MC objects. This is done by the
fsl_mc_msi_write_msg() callback, which is invoked by the generic MSI
layer with interrupts disabled. As a result, the mc_io used in
fsl_mc_msi_write_msg needs to be an atomic mc_io.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All the IRQs for DPAA2 objects in the same DPRC must use
the ICID of that DPRC, as their device Id in the GIC-ITS.
Thus, all these IRQs must share the same ITT table in the GIC.
As a result, a pool of IRQs with the same device Id must be
preallocated per DPRC (fsl-mc bus instance). So, the fsl-mc
bus object allocator is extended to also provide services
to allocate IRQs to DPAA2 devices, from their parent fsl-mc bus
IRQ pool.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Added platform-specific MSI support layer for FSL-MC devices.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Created an MSI domain for the fsl-mc bus-- including functions
to create a domain, find a domain, alloc/free domain irqs, and
bus specific overrides for domain and irq_chip ops.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

FSL-MC is a bus type different from PCI and platform, so it needs
its own member in the msi_desc's union.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since an FSL-MC bus is a new bus type that is neither PCI nor
PLATFORM, we need a new domain bus token to disambiguate the
IRQ domain for FSL-MC MSIs.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch.pl check:CHECK: spaces preferred around that '|'.
Add spaces around operands to fix these warnings.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>