- 14 Dec, 2014 40 commits
-
-
Scott Carter authored
commit 37017ac6 upstream. The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211) does not support 64-KB DMA transfers. Whenever a 64-KB DMA transfer is attempted, the transfer fails and messages similar to the following are written to the console log: [ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code [ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current] [ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out [ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00 [ 2431.851210] end_request: I/O error, dev sr0, sector 121808 When the libata and pata_serverworks modules are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h, the 64-KB transfer size in the scatter-gather list can be seen in the console log: [ 2664.897267] sr 9:0:0:0: [sr0] Send: [ 2664.897274] 0xf63d85e0 [ 2664.897283] sr 9:0:0:0: [sr0] CDB: [ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00 [ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700 [ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40 [ 2664.897338] ata_scsi_translate: ENTER [ 2664.897345] ata_sg_setup: ENTER, ata1 [ 2664.897356] ata_sg_setup: 3 sg elements mapped [ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000) [ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000) ------------------------------------------------------> ======= [ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000) [ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1 [ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC [ 2664.897428] ata_sff_tf_load: device 0xA0 [ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0 [ 2664.897457] ata_scsi_translate: EXIT [ 2664.897462] leaving scsi_dispatch_cmnd() [ 2664.897497] Doing sr request, dev = sr0, block = 0 [ 2664.897507] sr0 : reading 64/256 512 byte blocks. [ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58) [ 2664.897560] atapi_send_cdb: send cdb [ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64 [ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3 [ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51) [ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51) [ 2666.910129] sr 9:0:0:0: [sr0] Done: [ 2666.910136] 0xf63d85e0 TIMEOUT lspci shows that the driver used for the Broadcom OSB4 IDE Controller is pata_serverworks: 00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP]) Flags: bus master, medium devsel, latency 64 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] I/O ports at 0170 [size=8] I/O ports at 0374 [size=4] I/O ports at 1440 [size=16] Kernel driver in use: pata_serverworks The pata_serverworks driver supports five distinct device IDs, one being the OSB4 and the other four belonging to the CSB series. The CSB series appears to support 64-KB DMA transfers, as tests on a machine with an SAI2 motherboard containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212) showed no problems with 64-KB DMA transfers. This problem was first discovered when attempting to install openSUSE from a DVD on a machine with an STL2 motherboard. Using the pata_serverworks module, older releases of openSUSE will not install at all due to the timeouts. Releases of openSUSE prior to 11.3 can be installed by disabling the pata_serverworks module using the brokenmodules boot parameter, which causes the serverworks module to be used instead. Recent releases of openSUSE (12.2 and later) include better error recovery and will install, though very slowly. On all openSUSE releases, the problem can be recreated on a machine containing a Broadcom OSB4 IDE Controller by mounting an install DVD and running a command similar to the following: find /mnt -type f -print | xargs cat > /dev/null The patch below corrects the problem. Similar to the other ATA drivers that do not support 64-KB DMA transfers, the patch changes the ata_port_operations qc_prep vector to point to a routine that breaks any 64-KB segment into two 32-KB segments and changes the scsi_host_template sg_tablesize element to reduce by half the number of scatter/gather elements allowed. These two changes affect only the OSB4. Signed-off-by:
Scott Carter <ccscott@funsoft.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Chao Yu authored
commit 35425ea2 upstream. Christopher Head 2014-06-28 05:26:20 UTC described: "I tried to reproduce this on 3.12.21. Instead, when I do "echo hello > foo" in an ecryptfs mount with ecryptfs_xattr specified, I get a kernel crash: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 PGD d7840067 PUD b2c3c067 PMD 0 Oops: 0002 [#1] SMP Modules linked in: nvidia(PO) CPU: 3 PID: 3566 Comm: bash Tainted: P O 3.12.21-gentoo-r1 #2 Hardware name: ASUSTek Computer Inc. G60JX/G60JX, BIOS 206 03/15/2010 task: ffff8801948944c0 ti: ffff8800bad70000 task.ti: ffff8800bad70000 RIP: 0010:[<ffffffff8110eb39>] [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 RSP: 0018:ffff8800bad71c10 EFLAGS: 00010246 RAX: 00000000000181a4 RBX: ffff880198648480 RCX: 0000000000000000 RDX: 0000000000000004 RSI: ffff880172010450 RDI: 0000000000000000 RBP: ffff880198490e40 R08: 0000000000000000 R09: 0000000000000000 R10: ffff880172010450 R11: ffffea0002c51e80 R12: 0000000000002000 R13: 000000000000001a R14: 0000000000000000 R15: ffff880198490e40 FS: 00007ff224caa700(0000) GS:ffff88019fcc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000bb07f000 CR4: 00000000000007e0 Stack: ffffffff811826e8 ffff8800a39d8000 0000000000000000 000000000000001a ffff8800a01d0000 ffff8800a39d8000 ffffffff81185fd5 ffffffff81082c2c 00000001a39d8000 53d0abbc98490e40 0000000000000037 ffff8800a39d8220 Call Trace: [<ffffffff811826e8>] ? ecryptfs_setxattr+0x40/0x52 [<ffffffff81185fd5>] ? ecryptfs_write_metadata+0x1b3/0x223 [<ffffffff81082c2c>] ? should_resched+0x5/0x23 [<ffffffff8118322b>] ? ecryptfs_initialize_file+0xaf/0xd4 [<ffffffff81183344>] ? ecryptfs_create+0xf4/0x142 [<ffffffff810f8c0d>] ? vfs_create+0x48/0x71 [<ffffffff810f9c86>] ? do_last.isra.68+0x559/0x952 [<ffffffff810f7ce7>] ? link_path_walk+0xbd/0x458 [<ffffffff810fa2a3>] ? path_openat+0x224/0x472 [<ffffffff810fa7bd>] ? do_filp_open+0x2b/0x6f [<ffffffff81103606>] ? __alloc_fd+0xd6/0xe7 [<ffffffff810ee6ab>] ? do_sys_open+0x65/0xe9 [<ffffffff8157d022>] ? system_call_fastpath+0x16/0x1b RIP [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 RSP <ffff8800bad71c10> CR2: 0000000000000000 ---[ end trace df9dba5f1ddb8565 ]---" If we create a file when we mount with ecryptfs_xattr_metadata option, we will encounter a crash in this path: ->ecryptfs_create ->ecryptfs_initialize_file ->ecryptfs_write_metadata ->ecryptfs_write_metadata_to_xattr ->ecryptfs_setxattr ->fsstack_copy_attr_all It's because our dentry->d_inode used in fsstack_copy_attr_all is NULL, and it will be initialized when ecryptfs_initialize_file finish. So we should skip copying attr from lower inode when the value of ->d_inode is invalid. Signed-off-by:
Chao Yu <chao2.yu@samsung.com> Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Theodore Ts'o authored
commit f4bb2981 upstream. If there is a corrupted file system which has directory entries that point at reserved, metadata inodes, prohibit them from being used by treating them the same way we treat Boot Loader inodes --- that is, mark them to be bad inodes. This prohibits them from being opened, deleted, or modified via chmod, chown, utimes, etc. In particular, this prevents a corrupted file system which has a directory entry which points at the journal inode from being deleted and its blocks released, after which point Much Hilarity Ensues. Reported-by:
Sami Liedes <sami.liedes@iki.fi> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Theodore Ts'o authored
commit e2bfb088 upstream. The boot loader inode (inode #5) should never be visible in the directory hierarchy, but it's possible if the file system is corrupted that there will be a directory entry that points at inode #5. In order to avoid accidentally trashing it, when such a directory inode is opened, the inode will be marked as a bad inode, so that it's not possible to modify (or read) the inode from userspace. Unfortunately, when we unlink this (invalid/illegal) directory entry, we will put the bad inode on the ophan list, and then when try to unlink the directory, we don't actually remove the bad inode from the orphan list before freeing in-memory inode structure. This means the in-memory orphan list is corrupted, leading to a kernel oops. In addition, avoid truncating a bad inode in ext4_destroy_inode(), since truncating the boot loader inode is not a smart thing to do. Reported-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Alexey Khoroshilov authored
commit 56ec16cb upstream. If cn_add_callback() fails in dm_ulog_tfr_init(), it does not deallocate prealloced memory but calls cn_del_callback(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Reviewed-by:
Jonathan Brassow <jbrassow@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit eb76faf5 upstream. The 'last_accessed' member of the dm_buffer structure was only set when the the buffer was created. This led to each buffer being discarded after dm_bufio_max_age time even if it was used recently. In practice this resulted in all thinp metadata being evicted soon after being read -- this is particularly problematic for metadata intensive workloads like multithreaded small random IO. 'last_accessed' is now updated each time the buffer is moved to the head of the LRU list, so the buffer is now properly discarded if it was not used in dm_bufio_max_age time. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Geert Uytterhoeven authored
commit e4dc601b upstream. hwreg_present() and hwreg_write() temporarily change the VBR register to another vector table. This table contains a valid bus error handler only, all other entries point to arbitrary addresses. If an interrupt comes in while the temporary table is active, the processor will start executing at such an arbitrary address, and the kernel will crash. While most callers run early, before interrupts are enabled, or explicitly disable interrupts, Finn Thain pointed out that macsonic has one callsite that doesn't, causing intermittent boot crashes. There's another unsafe callsite in hilkbd. Fix this for good by disabling and restoring interrupts inside hwreg_present() and hwreg_write(). Explicitly disabling interrupts can be removed from the callsites later. Reported-by:
Finn Thain <fthain@telegraphics.com.au> Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Jan Kara authored
commit 90a80202 upstream. ->page_mkwrite() is used by filesystems to allocate blocks under a page which is becoming writeably mmapped in some process' address space. This allows a filesystem to return a page fault if there is not enough space available, user exceeds quota or similar problem happens, rather than silently discarding data later when writepage is called. However VFS fails to call ->page_mkwrite() in all the cases where filesystems need it when blocksize < pagesize. For example when blocksize = 1024, pagesize = 4096 the following is problematic: ftruncate(fd, 0); pwrite(fd, buf, 1024, 0); map = mmap(NULL, 1024, PROT_WRITE, MAP_SHARED, fd, 0); map[0] = 'a'; ----> page_mkwrite() for index 0 is called ftruncate(fd, 10000); /* or even pwrite(fd, buf, 1, 10000) */ mremap(map, 1024, 10000, 0); map[4095] = 'a'; ----> no page_mkwrite() called At the moment ->page_mkwrite() is called, filesystem can allocate only one block for the page because i_size == 1024. Otherwise it would create blocks beyond i_size which is generally undesirable. But later at ->writepage() time, we also need to store data at offset 4095 but we don't have block allocated for it. This patch introduces a helper function filesystems can use to have ->page_mkwrite() called at all the necessary moments. Signed-off-by:
-
Quinn Tran authored
commit 082f58ac upstream. During temporary resource starvation at lower transport layer, command is placed on queue full retry path, which expose this problem. The TCM queue full handling of SCF_TRANSPORT_TASK_SENSE currently sends the same cmd twice to lower layer. The 1st time led to cmd normal free path. The 2nd time cause Null pointer access. This regression bug was originally introduced v3.1-rc code in the following commit: commit e057f533 Author: Christoph Hellwig <hch@infradead.org> Date: Mon Oct 17 13:56:41 2011 -0400 target: remove the transport_qf_callback se_cmd callback Signed-off-by:
Quinn Tran <quinn.tran@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Andy Adamson authored
commit d1f456b0 upstream. Commit 2f60ea6b ("NFSv4: The NFSv4.0 client must send RENEW calls if it holds a delegation") set the NFS4_RENEW_TIMEOUT flag in nfs4_renew_state, and does not put an nfs41_proc_async_sequence call, the NFSv4.1 lease renewal heartbeat call, on the wire to renew the NFSv4.1 state if the flag was not set. The NFS4_RENEW_TIMEOUT flag is set when "now" is after the last renewal (cl_last_renewal) plus the lease time divided by 3. This is arbitrary and sometimes does the following: In normal operation, the only way a future state renewal call is put on the wire is via a call to nfs4_schedule_state_renewal, which schedules a nfs4_renew_state workqueue task. nfs4_renew_state determines if the NFS4_RENEW_TIMEOUT should be set, and the calls nfs41_proc_async_sequence, which only gets sent if the NFS4_RENEW_TIMEOUT flag is set. Then the nfs41_proc_async_sequence rpc_release function schedules another state remewal via nfs4_schedule_state_renewal. Without this change we can get into a state where an application stops accessing the NFSv4.1 share, state renewal calls stop due to the NFS4_RENEW_TIMEOUT flag _not_ being set. The only way to recover from this situation is with a clientid re-establishment, once the application resumes and the server has timed out the lease and so returns NFS4ERR_BAD_SESSION on the subsequent SEQUENCE operation. An example application: open, lock, write a file. sleep for 6 * lease (could be less) ulock, close. In the above example with NFSv4.1 delegations enabled, without this change, there are no OP_SEQUENCE state renewal calls during the sleep, and the clientid is recovered due to lease expiration on the close. This issue does not occur with NFSv4.1 delegations disabled, nor with NFSv4.0, with or without delegations enabled. Signed-off-by:
Andy Adamson <andros@netapp.com> Link: http://lkml.kernel.org/r/1411486536-23401-1-git-send-email-andros@netapp.com Fixes: 2f60ea6b (NFSv4: The NFSv4.0 client must send RENEW calls...) Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Mikulas Patocka authored
commit 5b789da8 upstream. The function bitcpy_rev has a bug that may result in screen corruption. The bug happens under these conditions: * the end of the destination area of a copy operation is aligned on a long word boundary * the end of the source area is not aligned on a long word boundary * we are copying more than one long word In this case, the variable shift is non-zero and the variable first is zero. The statements FB_WRITEL(comp(d0, FB_READL(dst), first), dst) reads the last long word of the destination and writes it back unchanged (because first is zero). Correctly, we should write the variable d0 to the last word of the destination in this case. This patch fixes the bug by introducing and extra test if first is zero. The patch also removes the references to fb_memmove in the code that is commented out because fb_memmove was removed from framebuffer subsystem. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Mikulas Patocka authored
commit f74a289b upstream. The framebuffer code uses the current background color to fill the border when switching consoles, however, this results in inconsistent behavior. For example: - start Midnigh Commander - the border is black - switch to another console and switch back - the border is cyan - type something into the command line in mc - the border is cyan - switch to another console and switch back - the border is black - press F9 to go to menu - the border is black - switch to another console and switch back - the border is dark blue When switching to a console with Midnight Commander, the border is random color that was left selected by the slang subsystem. This patch fixes this inconsistency by always using black as the background color when switching consoles. Signed-off-by:
-
Trond Myklebust authored
commit df817ba3 upstream. The current open/lock state recovery unfortunately does not handle errors such as NFS4ERR_CONN_NOT_BOUND_TO_SESSION correctly. Instead of looping, just proceeds as if the state manager is finished recovering. This patch ensures that we loop back, handle higher priority errors and complete the open/lock state recovery. Signed-off-by:
-
Ondrej Zary authored
commit 6d8ca28f upstream. Currently, ata_sff_softreset is skipped for controllers with no ctl port. But that also skips ata_sff_dev_classify required for device detection. This means that libata is currently broken on controllers with no ctl port. No device connected: [ 1.872480] pata_isapnp 01:01.02: activated [ 1.889823] scsi2 : pata_isapnp [ 1.890109] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 6.888110] ata3.01: qc timeout (cmd 0xec) [ 6.888179] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 16.888085] ata3.01: qc timeout (cmd 0xec) [ 16.888147] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.888086] ata3.01: qc timeout (cmd 0xec) [ 46.888148] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 51.888100] ata3.00: qc timeout (cmd 0xec) [ 51.888160] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) [ 61.888079] ata3.00: qc timeout (cmd 0xec) [ 61.888141] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) [ 91.888089] ata3.00: qc timeout (cmd 0xec) [ 91.888152] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x5) ATAPI device connected: [ 1.882061] pata_isapnp 01:01.02: activated [ 1.893430] scsi2 : pata_isapnp [ 1.893719] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 6.892107] ata3.01: qc timeout (cmd 0xec) [ 6.892171] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 16.892079] ata3.01: qc timeout (cmd 0xec) [ 16.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.892079] ata3.01: qc timeout (cmd 0xec) [ 46.892138] ata3.01: failed to IDENTIFY (I/O error, err_mask=0x5) [ 46.908586] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr [ 46.924570] ata3.00: configured for PIO0 (device error ignored) [ 46.926295] scsi 2:0:0:0: CD-ROM ACER CD-767E/O 1.5X PQ: 0 ANSI: 5 [ 46.984519] sr0: scsi3-mmc drive: 6x/6x xa/form2 tray [ 46.984592] cdrom: Uniform CD-ROM driver Revision: 3.20 So don't skip ata_sff_softreset, just skip the reset part of ata_bus_softreset if the ctl port is not available. This makes IDE port on ES968 behave correctly: No device connected: [ 4.670888] pata_isapnp 01:01.02: activated [ 4.673207] scsi host2: pata_isapnp [ 4.673675] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 7.081840] Adding 2541652k swap on /dev/sda2. Priority:-1 extents:1 across:2541652k ATAPI device connected: [ 4.704362] pata_isapnp 01:01.02: activated [ 4.706620] scsi host2: pata_isapnp [ 4.706877] ata3: PATA max PIO0 cmd 0x1e8 ctl 0x0 irq 11 [ 4.872782] ata3.00: ATAPI: ACER CD-767E/O, V1.5X, max PIO2, CDB intr [ 4.888673] ata3.00: configured for PIO0 (device error ignored) [ 4.893984] scsi 2:0:0:0: CD-ROM ACER CD-767E/O 1.5X PQ: 0 ANSI: 5 [ 7.015578] Adding 2541652k swap on /dev/sda2. Priority:-1 extents:1 across:2541652k Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Willy Tarreau authored
commit 72cf9012 upstream. This fix ensures that we never meet an integer overflow while adding 255 while parsing a variable length encoding. It works differently from commit 206a81c1 ("lzo: properly check for overruns") because instead of ensuring that we don't overrun the input, which is tricky to guarantee due to many assumptions in the code, it simply checks that the cumulated number of 255 read cannot overflow by bounding this number. The MAX_255_COUNT is the maximum number of times we can add 255 to a base count without overflowing an integer. The multiply will overflow when multiplying 255 by more than MAXINT/255. The sum will overflow earlier depending on the base count. Since the base count is taken from a u8 and a few bits, it is safe to assume that it will always be lower than or equal to 2*255, thus we can always prevent any overflow by accepting two less 255 steps. This patch also reduces the CPU overhead and actually increases performance by 1.1% compared to the initial code, while the previous fix costs 3.1% (measured on x86_64). The fix needs to be backported to all currently supported stable kernels. Reported-by:
Willem Pinckaers <willem@lekkertech.net> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Willy Tarreau authored
commit af958a38 upstream. This reverts commit 206a81c1 ("lzo: properly check for overruns"). As analysed by Willem Pinckaers, this fix is still incomplete on certain rare corner cases, and it is easier to restart from the original code. Reported-by:
-
Willy Tarreau authored
commit d98a0526 upstream. Add a complete description of the LZO format as processed by the decompressor. I have not found a public specification of this format hence this analysis, which will be used to better understand the code. Cc: Willem Pinckaers <willem@lekkertech.net> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit 6822ee34 upstream. "raw" is the name of a channel property, but should not be part of the channel name itself. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> [bwh: Backported to 3.2: using IIO_CHAN() macro to initialise the structures] Signed-off-by:
-
Stanislaw Gruszka authored
commit 01f7feea upstream. Two bits control TX power on BBP_R1 register. Correct the mask, otherwise we clear additional bit on BBP_R1 register, what can have unknown, possible negative effect. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Benjamin Coddington authored
commit 173b3afc upstream. If rpc.statd is restarted, upcalls to monitor hosts can fail with ECONNREFUSED. In that case force a lookup of statd's new port and retry the upcall. Signed-off-by:
Benjamin Coddington <bcodding@redhat.com> Signed-off-by:
-
Bryan O'Donoghue authored
commit ee1b5b16 upstream. Quark x1000 advertises PGE via the standard CPUID method PGE bits exist in Quark X1000's PTEs. In order to flush an individual PTE it is necessary to reload CR3 irrespective of the PTE.PGE bit. See Quark Core_DevMan_001.pdf section 6.4.11 This bug was fixed in Galileo kernels, unfixed vanilla kernels are expected to crash and burn on this platform. Signed-off-by:
Bryan O'Donoghue <pure.logic@nexus-software.ie> Cc: Borislav Petkov <bp@alien8.de> Link: http://lkml.kernel.org/r/1411514784-14885-1-git-send-email-pure.logic@nexus-software.ieSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
David Matlack authored
commit 2ea75be3 upstream. vcpu ioctls can hang the calling thread if issued while a vcpu is running. However, invalid ioctls can happen when userspace tries to probe the kind of file descriptors (e.g. isatty() calls ioctl(TCGETS)); in that case, we know the ioctl is going to be rejected as invalid anyway and we can fail before trying to take the vcpu mutex. This patch does not change functionality, it just makes invalid ioctls fail faster. Signed-off-by:
David Matlack <dmatlack@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Andy Shevchenko authored
commit 8e45ef68 upstream. Do full clean up at exit, means terminate all ongoing DMA transfers. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Andy Shevchenko authored
commit 63d84b1a upstream. commit fb57862e upstream. If the driver was compiled with DMA support, but DMA channels weren't acquired by some reason, mid_spi_dma_exit() will crash the kernel. Fixes: 7063c0d9 (spi/dw_spi: add DMA support) Signed-off-by:
-
Andy Shevchenko authored
commit b41583e7 upstream. In case of 8 bit mode and DMA usage we end up with every second byte written as 0. We have to respect bits_per_word settings what this patch actually does. Signed-off-by:
-
K. Y. Srinivasan authored
commit b29ef354 upstream. Minimize failures in this function by pre-allocating the buffer for posting messages. The hypercall for posting the message can fail for a number of reasons: 1. Transient resource related issues 2. Buffer alignment 3. Buffer cannot span a page boundry We address issues 2 and 3 by preallocating a per-cpu page for the buffer. Transient resource related failures are handled by retrying by the callers of this function. This patch is based on the investigation done by Dexuan Cui <decui@microsoft.com>. I would like to thank Sitsofe Wheeler <sitsofe@yahoo.com> for reporting the issue and helping in debuggging. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reported-by:
Sitsofe Wheeler <sitsofe@yahoo.com> Tested-by:
-
K. Y. Srinivasan authored
commit 98d731bb upstream. Eliminate calls to BUG_ON() in vmbus_close_internal(). We have chosen to potentially leak memory, than crash the guest in case of failures. In this version of the patch I have addressed comments from Dan Carpenter (dan.carpenter@oracle.com). Signed-off-by:
-
K. Y. Srinivasan authored
commit 45d727ce upstream. Fix a bug in vmbus_open() and properly propagate the error. I would like to thank Dexuan Cui <decui@microsoft.com> for identifying the issue. Signed-off-by:
-
K. Y. Srinivasan authored
commit 72c6b71c upstream. Eliminate the call to BUG_ON() by waiting for the host to respond. We are trying to reclaim the ownership of memory that was given to the host and so we will have to wait until the host responds. Signed-off-by:
-
K. Y. Srinivasan authored
commit 66be6530 upstream. Eliminate calls to BUG_ON() by properly handling errors. In cases where rollback is possible, we will return the appropriate error to have the calling code decide how to rollback state. In the case where we are transferring ownership of the guest physical pages to the host, we will wait for the host to respond. Signed-off-by:
-
K. Y. Srinivasan authored
commit fdeebcc6 upstream. Posting messages to the host can fail because of transient resource related failures. Correctly deal with these failures and increase the number of attempts to post the message before giving up. In this version of the patch, I have normalized the error code to Linux error code. Signed-off-by:
-
Kees Cook authored
commit 471b095d upstream. An empty firmware request name will trigger warnings when building device names. Make sure this is caught earlier and rejected. The warning was visible via the test_firmware.ko module interface: echo -ne "\x00" > /sys/devices/virtual/misc/test_firmware/trigger_request Reported-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Kees Cook <keescook@chromium.org> Tested-by:
-
Lu Baolu authored
commit ddbe1fca upstream. This full-speed USB device generates spurious remote wakeup event as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result, Linux can't enter system suspend and S0ix power saving modes once this keyboard is used. This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk. With this quirk set, wakeup capability will be ignored during device configure. This patch could be back-ported to kernels as old as 2.6.39. Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Joonyoung Shim authored
commit 526a4045 upstream. The usb device will autoresume from choose_wakeup() if it is autosuspended with the wrong wakeup setting, but below errors occur because usb3503 misc driver will switch to standby mode when suspended. As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from autosuspend_check(). [ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 7.854658] usb 1-3: device descriptor read/64, error -71 [ 8.079657] usb 1-3: device descriptor read/64, error -71 [ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 8.414658] usb 1-3: device descriptor read/64, error -71 [ 8.639657] usb 1-3: device descriptor read/64, error -71 [ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 9.264598] usb 1-3: device not accepting address 3, error -71 [ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci [ 9.784601] usb 1-3: device not accepting address 3, error -71 [ 9.784838] usb usb1-port3: device 1-3 not suspended yet Signed-off-by:
Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by:
-
Maciej Matraszek authored
commit 3bacc10c upstream. Fix clamp_align() used in v4l_bound_align_image() to prevent overflow when passed large value like UINT32_MAX. In the current implementation: clamp_align(UINT32_MAX, 8, 8192, 3) returns 8, because in line: x = (x + (1 << (align - 1))) & mask; x overflows to (-1 + 4) & 0x7 = 3, while expected value is 8192. v4l_bound_align_image() is heavily used in VIDIOC_S_FMT and VIDIOC_SUBDEV_S_FMT ioctls handlers, and documentation of the latter explicitly states that: "The modified format should be as close as possible to the original request." -- http://linuxtv.org/downloads/v4l-dvb-apis/vidioc-subdev-g-fmt.html Thus one would expect, that passing UINT32_MAX as format width and height will result in setting maximum possible resolution for the device. Particularly, when the driver doesn't support VIDIOC_ENUM_FRAMESIZES ioctl, which is common in the codebase. Fixes changeset: b0d3159bSigned-off-by:
Maciej Matraszek <m.matraszek@samsung.com> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Ricardo Ribalda Delgado authored
commit 89ec3dcf upstream. Some implementations of modprobe fail to load the driver for a PCI device automatically because the "interface" part of the modalias from the kernel is lowercase, and the modalias from file2alias is uppercase. The "interface" is the low-order byte of the Class Code, defined in PCI r3.0, Appendix D. Most interface types defined in the spec do not use alpha characters, so they won't be affected. For example, 00h, 01h, 10h, 20h, etc. are unaffected. Print the "interface" byte of the Class Code in uppercase hex, as we already do for the Vendor ID, Device ID, Class, etc. [bhelgaas: changelog] Signed-off-by:
Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
-
Andreas Bomholtz authored
commit dee80ad1 upstream. Added the Seluxit ApS USB Serial Dongle to cp210x driver. Signed-off-by:
Andreas Bomholtz <andreas@seluxit.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Joe Savage authored
commit bfc2d7df upstream. Added support for Ketra N1 wireless interface, which uses the Silicon Labs' CP2104 USB to UART bridge with customized PID 8946. Signed-off-by:
Joe Savage <joe.savage@goketra.com> Signed-off-by:
-
Paul Fertser authored
commit 62ea864f upstream. As reported on [1], this device needs this quirk to be able to reliably initialise the webcam. [1] http://ubuntuforums.org/showthread.php?t=2145996Signed-off-by:
Paul Fertser <fercerpav@gmail.com> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Jan Kara authored
commit 279bf6d3 upstream. The check whether quota format is set even though there are no quota files with journalled quota is pointless and it actually makes it impossible to turn off journalled quotas (as there's no way to unset journalled quota format). Just remove the check. Signed-off-by:
-
