- 03 Apr, 2016 10 commits
-
-
Linus Walleij authored
All the ST Sensors use the old "<foo>-trigger" rather than the standard "<foo>-devN" new standard suffix for triggers. Now much to do about it since it is ABI, but make the testing tools recognize it too. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Jonathan Cameron <jic23@kernel.org>
-
Irina Tirdea authored
Commit 845c8770 ("i2c / ACPI: Assign IRQ for devices that have GpioInt automatically") automatically assigns the first ACPI GPIO interrupt in client->irq, so we can remove the probing code from drivers that use only one interrupt. Commit 0f079650 ("iio: remove gpio interrupt probing from drivers that use a single interrupt") removes gpio interrupt probing from most drivers. This patch cleans the remaining ones. Signed-off-by:
Irina Tirdea <irina.tirdea@intel.com> Signed-off-by:
-
Irina Tirdea authored
GPIO handling code has been removed from the drivers (since this is now handled by the ACPI core) in commit 0f079650 ("iio: remove gpio interrupt probing from drivers that use a single interrupt"). Remove the include for linux/gpio/consumer.h since it is no longer used. Signed-off-by:
-
Adriana Reus authored
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to enable/disable the bus at each i2c transfer and must wait for the enable/disable to happen before sending the data. When reading data in the trigger handler, the kxcjk-1013 accel driver does one i2c transfer for each axis. This has an impact on the frequency of the accelerometer at high sample rates due to additional delays introduced by the i2c bus at each transfer. Reading all axis values in one i2c transfer reduces the delays introduced by the i2c bus. Uses i2c_smbus_read_i2c_block_data_or_emulated that will fallback to reading each axis as a separate word in case i2c block read is not supported. Signed-off-by:
Adriana Reus <adriana.reus@intel.com> Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Adriana Reus authored
Use available_scan_masks to allow the iio core to select the data to send to userspace depending on which axes are enabled, instead of doing this in the driver's interrupt handler. Signed-off-by:
-
Irina Tirdea authored
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to enable/disable the bus at each i2c transfer and must wait for the enable/disable to happen before sending the data. When reading data in the trigger handler, the bmg160 gyro driver does one bus transfer for each axis. This has an impact on the frequency of the accelerometer at high sample rates due to additional delays introduced by the bus at each transfer. Reading all axis values in one bus transfer reduces the delays introduced by the bus. Signed-off-by:
-
Irina Tirdea authored
Use available_scan_masks to allow the iio core to select the data to send to userspace depending on which axes are enabled, instead of doing this in the driver's interrupt handler. Signed-off-by:
-
Irina Tirdea authored
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to enable/disable the bus at each i2c transfer and must wait for the enable/disable to happen before sending the data. When reading data in the trigger handler, the bmc150 accel driver does one bus transfer for each axis. This has an impact on the frequency of the accelerometer at high sample rates due to additional delays introduced by the bus at each transfer. Reading all axis values in one bus transfer reduces the delays introduced by the bus. Signed-off-by:
-
Irina Tirdea authored
Use available_scan_masks to allow the iio core to select the data to send to userspace depending on which axes are enabled, instead of doing this in the driver's interrupt handler. Signed-off-by:
-
Slawomir Stepien authored
Use const pointer to element from model configuration array rather then array index, as it will not change anyway. Signed-off-by:
Slawomir Stepien <sst@poczta.fm> Signed-off-by:
Peter Rosin <peda@axentia.se> Signed-off-by:
-
- 28 Mar, 2016 2 commits
-
-
Alison Schofield authored
Use kernel preferred unsigned int declaration style. Patch created using: git ls-files drivers/staging/iio | \ xargs ./scripts/checkpatch.pl -f --fix-inplace --types=unspecified_int Hand edits restored columns in structure definitions. Signed-off-by:
Alison Schofield <amsfield22@gmail.com> Signed-off-by:
-
Linus Walleij authored
The driver goes to some length to dynamically allocate an array to hold the channel addresses. However no ST sensor has more than three channels (x, y, z at most). Instead of kmalloc():ing and kfree():in the address array, just use a fixed array of three elements. Cc: Giuseppe Barba <giuseppe.barba@st.com> Signed-off-by:
Denis Ciocca <denis.ciocca@st.com> Signed-off-by:
-
- 21 Mar, 2016 1 commit
-
-
Marc Titinger authored
The user (or an init script) may setup RShunt via sysfs after the driver was initialized, for instance based on the EEPROM contents of a modular probe. The calibration register must be set accordingly. Signed-off-by:
Marc Titinger <marc.titinger@baylibre.com> Signed-off-by:
-
- 20 Mar, 2016 12 commits
-
-
Gregor Boirie authored
Ensure optional regulator is properly disabled when present. Fixes: 63d5d525 ("iio:magnetometer:ak8975: power regulator support") Signed-off-by:
Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by:
-
Amitoj Kaur Chawla authored
flush_scheduled_work is scheduled for deprecation. Replace cancel_delayed_work and flush_scheduled_work with cancel_delayed_work_sync instead to ensure there is no pending or running work item. Since there is only one work item, chip->poweroff_work, there are no further dependencies of flush_scheduled_work(). Acked-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by:
-
Gregor Boirie authored
Ensure optional regulator is properly disabled when present. Fixes: 3145229f ("iio:pressure:ms5611: power regulator support") Signed-off-by:
-
Daniel Baluta authored
When using ACPI, id is NULL and the current code automatically defaults name to NULL and chip id to 0. We should instead use the data provided in the ACPI device table. Fixes: c816d9e7 ("iio: imu: mpu6050: fix possible NULL dereferences") Signed-off-by:
Daniel Baluta <daniel.baluta@intel.com> Reviewed-By:
Matt Ranostay <matt.ranostay@intel.com> Signed-off-by:
-
David Wu authored
The ADC is a 6-channel signal-ended 10-bit Successive Approximation Register (SAR) A/D Converter. Signed-off-by:
David Wu <david.wu@rock-chips.com> Signed-off-by:
-
Alison Schofield authored
Driver includes struct regmap and struct device in its global data. Remove the struct device and use regmap API to retrieve device info. Simplified version of Coccinelle semantic patch used: @ a @ identifier drvdata, r; position p; @@ struct drvdata@p { ... struct regmap *r; ... }; @ b @ identifier a.drvdata, d; position a.p; @@ struct drvdata@p { ... - struct device *d; ... }; @ passed depends on b @ identifier a.drvdata, a.r, b.d, i, f; @@ f (..., struct drvdata *i ,...) { + struct device *dev = regmap_get_device(i->r); <+... - i->d + dev ...+> } Signed-off-by: -
Peter Meerwald-Stadler authored
add recently added channel types and modifiers Signed-off-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Signed-off-by:
-
Martin Kepplinger authored
What is this autosleep? ----------------------- It slows down the device after x seconds of inactivity. The thing is, we have really achieved almost the same by runtime pm. differnces are: autosleep * uses more power during inactivity * the first read after inactivity slightly faster * complicated to understand for the user * no documented sysfs interface (afaik) * complicated to read and maintain runtime pm * already merged in mma8452 * uses less power during inactivity * first read after inactivity slower * easy to use. well documented. * easy to maintain and understand The two approaches solve the same problem. runtime pm has more advantages than autosleep and comes quite close to it's behaviour anyways. As I see it, autosleep, even if somehow supported, would never be used anyways. So resolve this issue by "ignoring" autosleep. Signed-off-by:
Martin Kepplinger <martink@posteo.de> Reviewed-by:
Martina Kepplinger <martina.novakovic@zoho.com> Signed-off-by:
-
Martin Kepplinger authored
This was forgotten about and is added for consistency now Signed-off-by:
-
Peter Meerwald authored
Signed-off-by:
-
Peter Meerwald-Stadler authored
happily married for 4 month :) Signed-off-by:
-
Joachim Eastwood authored
Signed-off-by:
Joachim Eastwood <manabian@gmail.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
- 12 Mar, 2016 7 commits
-
-
Joachim Eastwood authored
Add base support for the 10-bit DAC peripheral found on NXP LPC18xx/43xx SoCs. This is a minimal driver that does not support DMA or interrupts. User manual with register description can be found on: LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf Signed-off-by:
-
Joachim Eastwood authored
Signed-off-by:
-
Joachim Eastwood authored
Add base support for the 10-bit SAR ADC peripheral found on NXP LPC18xx/43xx SoCs. This is a minimal driver that does not support burst mode, interrupts, DMA or hardware triggers. User manual with register description can be found on: LPC18xx: www.nxp.com/documents/user_manual/UM10430.pdf LPC43xx: www.nxp.com/documents/user_manual/UM10503.pdf Signed-off-by:
-
Alison Schofield authored
Replace the code that guarantees the device stays in direct mode with iio_device_{claim|release}_direct_mode() which does same. Signed-off-by: -
Alison Schofield authored
It is often the case that the driver wants to be sure a device stays in direct mode while it is executing a task or series of tasks. To accomplish this today, the driver performs this sequence: 1) take the device state lock, 2) verify it is not in a buffered mode, 3) execute some tasks, and 4) release that lock. This patch introduces a pair of helper functions that simplify these steps and make it more semantically expressive. iio_device_claim_direct_mode() If the device is not in any buffered mode it is guaranteed to stay that way until iio_release_direct_mode() is called. iio_device_release_direct_mode() Release the claim. Device is no longer guaranteed to stay in direct mode. Signed-off-by: -
Martin Kepplinger authored
This adds support for Freescale's (now NXP's) FXLS8471Q accelerometer. We use MMA8451Q's configuration because for what the driver supports, FXLS8471Q is the same. Support for FXLS8471Q's features (fast SPI interface and a larger FIFO, among others) can be added to this driver anytime. See it's datasheet for the details: http://cache.nxp.com/files/sensors/doc/data_sheet/FXLS8471Q.pdfSigned-off-by:
-
Tiberiu Breana authored
This commit adds support for STMicroelectronics h3lis331dl high-g accelerometer. The datasheet for this device can be found here: http://www.st.com/web/en/resource/technical/document/ datasheet/DM00053090.pdf Signed-off-by:
Tiberiu Breana <tiberiu.a.breana@intel.com> Reviewed-by:
-
- 09 Mar, 2016 2 commits
-
-
Lars-Peter Clausen authored
The ADIS16220 part has been obsoleted, which makes it hard to get the hardware to even test the driver. Considering this there is no expectation that the driver will be cleaned up and be able to move out of staging, so remove the driver. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Lars-Peter Clausen authored
The ADIS16204 part has been obsoleted, which makes it hard to get the hardware to even test the driver. Considering this there is no expectation that the driver will be cleaned up and be able to move out of staging, so remove the driver. Signed-off-by:
-
- 05 Mar, 2016 6 commits
-
-
Krzysztof Kozlowski authored
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um allyesconfig (COMPILE_TEST) failed with: drivers/built-in.o: In function `at91_adc_probe': at91-sama5d2_adc.c:(.text+0x48f548): undefined reference to `devm_ioremap_resource' Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Matt Ranostay authored
Fix possible null dereferencing of i2c and spi driver data. Signed-off-by:
-
Martin Kepplinger authored
This adds support for runtime power management and, if configured, activates automatic standby after 2 seconds of inactivity. Inactivity means no read of acceleration values and no events triggered or activated. If CONFIG_PM is not set, this doesn't change anything for existing users. Signed-off-by:
Christoph Muellner <christoph.muellner@theobroma-systems.com> Signed-off-by:
-
Martin Kepplinger authored
The devices' config registers can only be changed in standby mode. Up until now the driver just held the device *always* active, so for changing a config it was *always* necessary to switch to standby. For upcoming support for runtime pm, the device can as well be in standby mode. Instead of putting runtime pm functions in there, just keep the device in standby if it already is. This section is protected by a lock after all. Signed-off-by:
-
Martin Kepplinger authored
fix checkpatch issues like "space before tabs", too long lines or alignment. Signed-off-by:
-
Gregor Boirie authored
Add support for an optional regulator which, if found into device-tree, will power on device at probing time. The regulator is declared into ak8975 DTS entry as a "vdd-supply" property. Signed-off-by:
-
