This errata covers all r1 variants of Cortex A8, it's not limited to
just r1p0..r1p2.  Update the documentation to reflect this.  The code
already applies the workaround to all r1p* A8 CPUs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We have recently had an example of someone wanting to use a 90kHz timer
for the software delay loop.

udelay() needs to have at least microsecond resolution to allow drivers
access to a delay mechanism with a reasonable chance of delaying the
period they requested within at least a 50% marging of error, especially
for small delays.

Discussion about the udelay() accuracy can be found at:
	https://lkml.org/lkml/2011/1/9/37

Reject timers which are unable to supply this level of resolution.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Switch ARM to use the generic show_mem() implementation, which displays
the statistics from the mm zone rather than walking the page arrays.
Acked-by: Mel Gorman &lt;mgorman <mgorman@suse.de>
Tested-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Avoid the errata 430973 workaround for non-Cortex A8 CPUs.  Having this
workaround enabled introduces an additional branch target buffer flush
into the context switching path, something we wish to avoid.  To allow
this errata to be enabled in multiplatform kernels while reducing its
impact, rearrange the Cortex-A8 CPU support to avoid impacting on other
Version 7 CPUs.
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The effects of not having ARM errata 643719 enabled on affected CPUs
can be very confusing and hard to debug.  Rather than leave this to
chance, enable this workaround by default.  Now that we have rearranged
the code, it should have a low impact on the majority of CPUs.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Eliminate one unnecessary instruction from this test by pre-shifting
the Cortex A9 ID - we can shift the actual ID in the teq instruction
thereby losing the pX bit of the ID at no cost.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Optimise the branches such that for the majority of unaffected devices,
we avoid needing to execute the errata work-around code path by
branching to start_flush_levels early.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Both v7_flush_cache_louis and v7_flush_dcache_all both begin the
flush_levels loop with r10 initialised to zero.  In each case, this
is done immediately prior to entering the loop.  Branch to this
instruction in v7_flush_dcache_all from v7_flush_cache_louis and
eliminate the unnecessary initialisation in v7_flush_cache_louis.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Rather than have code which masks and then shifts, such as:

	mrc     p15, 1, r0, c0, c0, 1
ALT_SMP(ands	r3, r0, #7 << 21)
ALT_UP( ands	r3, r0, #7 << 27)
ALT_SMP(mov	r3, r3, lsr #20)
ALT_UP(	mov	r3, r3, lsr #26)

re-arrange this as a shift and then mask.  The masking is the same for
each field which we want to extract, so this allows the mask to be
shared amongst code paths:

	mrc     p15, 1, r0, c0, c0, 1
ALT_SMP(mov	r3, r0, lsr #20)
ALT_UP(	mov	r3, r0, lsr #26)
	ands	r3, r3, #7 << 1

Use this method for the LoUIS, LoUU and LoC fields.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We always build cache-v7.S for ARMv7, so we can use the ARMv7 16-bit
move instructions to load large constants, rather than using constants
in a literal pool.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Allow ALT_UP() to cope with a 16-bit Thumb instruction by automatically
inserting a following nop instruction.  This allows us to care less
about getting the assembler to emit a 32-bit thumb instruction.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Documentation: DT bindings: Tegra AHB: require the legacy base address for existing chips

Per Stephen Warren, note in the Tegra AHB DT binding documentation
that we specifically deprecate any attempt to use the IP block's
actual hardware base address, and advocate the use of the legacy
"off-by-four" address in the 'regs' property, for Tegra chips with
existing upstream Linux DT files that include a Tegra AHB node.  This
patch updates the documentation accordingly.

Changing the existing kernel DT data isn't under consideration because
Linux kernel DT data policy is to preserve compatibility between newer
DT data files and older kernels.  However, this additional step of
changing the documentation should discourage others from sending
kernel patches to try to change the legacy kernel DT data.
Furthermore, for out-of-tree software (such as bootloaders or other
operating systems) that may rely on Linux kernel DT binding
documentation as an ABI (but not the Linux kernel DT data itself),
such a change may allow future convergence with the Linux kernel DT
data without additional code changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

amba: tegra-ahb: detect and correct bogus base address

From a hardware SoC integration point of view, the starting address of
this IP block in the existing Tegra SoC DT files is off by 4 bytes
from the actual base address.  Since we attempt to make old DT files
forward-compatible with newer kernels, we cannot fix the IP block base
address in old DT data. This patch works around the problem by
detecting the four byte base address offset in the driver code, and
correcting it if it's detected.  (In general, IP block base addresses
almost always have a null low byte.)

Future SoC DT data for Tegra AHB should use the correct Tegra AHB base
address, in cases where there is no DT data backward compatibility
requirement.

This patch is a revision of the patch originally titled
"amba: tegra-ahb: use correct base address for future chip support".
This revision implements changes requested by Russell King:

http://marc.info/?l=linux-tegra&m=142658851825062&w=2
http://marc.info/?l=linux-tegra&m=142658873925178&w=2Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hiroshi DOYU <hdoyu@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

amba: tegra-ahb: fix register offsets in the macros

From a hardware SoC integration point of view, the offsets of the
Tegra AHB registers that are currently defined in tegra-ahb.c macros
are all off by four bytes.  Similarly, the starting address of this IP
block in our existing DT files is also off by four bytes.  Since we
attempt to make old DT files forward-compatible with newer kernels, we
cannot fix the IP block base address in old DT data.  However, we can
fix the offsets in the driver so that they are correct with respect to
the hardware, which is what this patch does.  And a subsequent patch
will allow the offset to be removed for DT 'compatible' strings used
in future DT files for newer Tegra chips that the kernel does not yet
support.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hiroshi DOYU <hdoyu@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Several interrupt controllers support both edge and level interrupts, so
it's useful to provide that information in /proc/interrupts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When trying to kexec into a new kernel on a platform where multiple CPU
cores are present, but no SMP bringup code is available yet, the
kexec_load system call fails with:

    kexec_load failed: Invalid argument

The SMP test added to machine_kexec_prepare() in commit 2103f6cb
("ARM: 7807/1: kexec: validate CPU hotplug support") wants to prohibit
kexec on SMP platforms where it cannot disable secondary CPUs.
However, this test is too strict: if the secondary CPUs couldn't be
enabled in the first place, there's no need to disable them later at
kexec time.  Hence skip the test in the absence of SMP bringup code.

This allows to add all CPU cores to the DTS from the beginning, without
having to implement SMP bringup first, improving DT compatibility.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move shutdown and reboot related code to a separate file, out of
process.c.  This helps to avoid polluting process.c with non-process
related code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Normally, when a CPU wants to clear a cache line to zero in the external
L2 cache, it would generate bus cycles to write each word as it would do
with any other data access.

However, a Cortex A9 connected to a L2C-310 has a specific feature where
the CPU can detect this operation, and signal that it wants to zero an
entire cache line.  This feature, known as Full Line of Zeros (FLZ),
involves a non-standard AXI signalling mechanism which only the L2C-310
can properly interpret.

There are separate enable bits in both the L2C-310 and the Cortex A9 -
the L2C-310 needs to be enabled and have the FLZ enable bit set in the
auxiliary control register before the Cortex A9 has this feature
enabled.

Unfortunately, the suspend code was not respecting this - it's not
obvious from the code:

swsusp_arch_suspend()
 cpu_suspend() /* saves the Cortex A9 auxiliary control register */
  arch_save_image()
  soft_restart() /* turns off FLZ in Cortex A9, and disables L2C */
   cpu_resume() /* restores the Cortex A9 registers, inc auxcr */

At this point, we end up with the L2C disabled, but the Cortex A9 with
FLZ enabled - which means any memset() or zeroing of a full cache line
will fail to take effect.

A similar issue exists in the resume path, but it's slightly more
complex:

swsusp_arch_suspend()
 cpu_suspend() /* saves the Cortex A9 auxiliary control register */
  arch_save_image() /* image with A9 auxcr saved */
...
swsusp_arch_resume()
 call_with_stack()
  arch_restore_image() /* restores image with A9 auxcr saved above */
  soft_restart() /* turns off FLZ in Cortex A9, and disables L2C */
   cpu_resume() /* restores the Cortex A9 registers, inc auxcr */

Again, here we end up with the L2C disabled, but Cortex A9 FLZ enabled.

There's no need to turn off the L2C in either of these two paths; there
are benefits from not doing so - for example, the page copies will be
faster with the L2C enabled.

Hence, fix this by providing a variant of soft_restart() which can be
used without turning the L2 cache controller off, and use it in both
of these paths to keep the L2C enabled across the respective resume
transitions.

Fixes: 8ef418c7 ("ARM: l2c: trial at enabling some Cortex-A9 optimisations")
Reported-by: Sean Cross <xobs@kosagi.com>
Tested-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This code calls cpu_resume() using a straight branch (b), so
now that we have moved cpu_resume() back to .text, this should
be moved there as well.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This code calls cpu_resume() using a straight branch (b), so
now that we have moved cpu_resume() back to .text, this should
be moved there as well. Any direct references to symbols that will
remain in the .data section are replaced with explicit PC-relative
references.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Move cpu_resume() to the .text section where it belongs. Change
the adr reference to sleep_save_sp to an explicit PC relative
reference so sleep_save_sp itself can remain in .data.

This helps prevent linker failure on large kernels, as the code
in the .data section may be too far away to be in range for normal
b/bl instructions.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When building a very large kernel, it is up to the linker to decide
when and where to insert stubs to allow calls to functions that are
out of range for the ordinary b/bl instructions.

However, since the kernel is built as a position dependent binary,
these stubs (aka veneers) may contain absolute addresses, which will
break far calls performed with the MMU off.

For instance, the call from __enable_mmu() in the .head.text section
to __turn_mmu_on() in the .idmap.text section may be turned into
something like this:

c0008168 <__enable_mmu>:
c0008168:       f020 0002       bic.w   r0, r0, #2
c000816c:       f420 5080       bic.w   r0, r0, #4096
c0008170:       f000 b846       b.w     c0008200 <____turn_mmu_on_veneer>
[...]
c0008200 <____turn_mmu_on_veneer>:
c0008200:       4778            bx      pc
c0008202:       46c0            nop
c0008204:       e59fc000        ldr     ip, [pc]
c0008208:       e12fff1c        bx      ip
c000820c:       c13dfae1        teqgt   sp, r1, ror #21
[...]
c13dfae0 <__turn_mmu_on>:
c13dfae0:       4600            mov     r0, r0
[...]

After adding --pic-veneer to the LDFLAGS, the veneer is emitted like
this instead:

c0008200 <____turn_mmu_on_veneer>:
c0008200:       4778            bx      pc
c0008202:       46c0            nop
c0008204:       e59fc004        ldr     ip, [pc, #4]
c0008208:       e08fc00c        add     ip, pc, ip
c000820c:       e12fff1c        bx      ip
c0008210:       013d7d31        teqeq   sp, r1, lsr sp
c0008214:       00000000        andeq   r0, r0, r0

Note that this particular example is best addressed by moving
.head.text and .idmap.text closer together, but this issue could
potentially affect any code that needs to execute with the
MMU off.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This moves all fixup snippets to the .text.fixup section, which is
a special section that gets emitted along with the .text section
for each input object file, i.e., the snippets are kept much closer
to the code they refer to, which helps prevent linker failure on
large kernels.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This introduces a new .text.fixup input section that gets emitted
together with the .text section for each input object file.

Note that

  *(.text)
  *(.text.fixup)

is not the same as

  *(.text .text.fixup)

and we are looking for the latter, to ensure that fixup snippets that
are assembled into a separate section in the object file do not end
up out of range for the relative branch instructions it contains if
the .text section itself grows very large.

This helps prevent linker failures on large ARM kernels.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

arm64 builds with GCC 5 have caused the __asmeq assertions in the PSCI
calling code to fire, so move the ARM PSCI calls out of line into their
own assembly file for consistency and to safeguard against the same
issue occuring with the 32-bit toolchain.

[will: brought into line with arm64 implementation]
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When the patch for e16343c4 (ARM: 8160/1: drop warning about
return_address not using unwind tables) was created there was still more
code in said branch. Probably this simplification was just missed during
conflict resolution when the patch was applied.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch makes it possible to enter zImage in Thumb mode for ARMv7-M
(Cortex-M) CPUs that do not support ARM mode. The kernel entry is also
made in Thumb mode.

[ukl: fix spelling in commit log, return early in call_cache_fn]
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When running the 32-bit ARM kernel on ARMv8 capable bare metal (e.g.,
32-bit Android userland and kernel on a Cortex-A53), or as a KVM guest
on a 64-bit host, we should advertise the availability of the Crypto
instructions, so that userland libraries such as OpenSSL may use them.
(Support for the v8 Crypto instructions in the 32-bit build was added
to OpenSSL more than six months ago)

This adds the ID feature bit detection, and sets elf_hwcap2 accordingly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The various CPU feature registers consist of 4-bit blocks that
represent signed quantities, whose positive values represent
incremental features, and whose negative values are reserved.

To improve forward compatibility, update the feature detection
code to take possible future higher values into account, but
ignore negative values.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This moves the .idmap.text section closer to .head.text, so that
relative branches are less likely to go out of range if the kernel
text gets bigger.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch replaces the 'branch to setup()' instructions embedded
in the PROCINFO structs with the offset to that setup function
relative to the base of the struct. This preserves the position
independent nature of that field, but uses a data item rather
than an instruction.

This is mainly done to prevent linker failures on large kernels,
where the setup function is out of reach for the branch.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Occasionally, there's a question about the method we use to find the
start of physical memory.  Add some documentation so we don't have to
keep repeating outselves on the mailing list.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When using the IOMMU-backed DMA ops for a device, we store a pointer to
the dma_iommu_mapping structure (used to keep track of the address
space) in the archdata.mapping field of the struct device.

Rather than access this field directly, use the to_dma_iommu_mapping
helper in dma-mapping, so that we don't really care where the mapping
information is held.

Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Make sure that we can read the "cache-level" property from the L2 cache
controller node, and ensure its value is 2.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

SMP_ON_UP has been around for a while, and seems to be well-proven now.
Drop the EXPERIMENTAL tag from the option.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Even without an iommu, NO_KERNEL_MAPPING is still convenient to save on
kernel address space in places where we don't need a kernel mapping.
Implement support for it in the two places where we're creating an
expensive mapping.

__alloc_from_pool uses an internal pool from which we already have
virtual addresses, so it's not relevant, and __alloc_simple_buffer uses
alloc_pages, which will always return a lowmem page, which is already
mapped into kernel space, so we can't prevent a mapping for it in that
case.
Signed-off-by: Jasper St. Pierre <jstpierre@mecheye.net>
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Drake <dsd@endlessm.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The pci_mmap_page_range() API should be written to expect offset
values representing PCI memory resource addresses as seen by user
space, through the pci_resource_to_user() API.

ARM relies on the standard implementation of pci_resource_to_user()
which actually is an identity map and exports to user space
PCI memory resources as they are stored in PCI devices resources
structures, which represent CPU physical addresses (fixed-up using
BUS to CPU address conversions) not PCI bus addresses.

Therefore, on ARM platforms where the mapping between CPU and BUS
address is not a 1:1 the current pci_mmap_page_range() implementation is
erroneous, in that an additional shift is applied to an already fixed-up
offset passed from userspace.

Hence, this patch removes the mem_offset from the pgoff calculation
since the offset as passed from user space already represents the CPU
physical address corresponding to the resource to be mapped, ie no
additional offset should be applied.

Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently, interworking calls on module boundaries are not supported,
and are handled by the same error handling code path as non-interworking
calls whose targets are simply out of range.

Before modifying the handling of those out-of-range jump and call
relocations in a subsequent patch, move the handling of interworking
restrictions out of it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

.. after extensive statistical analysis of my G+ polling, I've come to
the inescapable conclusion that internet polls are bad.

Big surprise.

But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38%
margin, in a poll that people weren't even supposed to participate in.
Who can argue with solid numbers like that? 5,796 votes from people who
can't even follow the most basic directions?

In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%,
but with a total of 29,110 votes right now.

Now, arguably, that vote spread is only about 3,200 votes, which is less
than the almost six thousand votes that the "please ignore" poll got, so
it could be considered noise.

But hey, I asked, so I'll honor the votes.

Pull ext4 fixes from Ted Ts'o:
 "Ext4 bug fixes.

  We also reserved code points for encryption and read-only images (for
  which the implementation is mostly just the reserved code point for a
  read-only feature :-)"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix indirect punch hole corruption
  ext4: ignore journal checksum on remount; don't fail
  ext4: remove duplicate remount check for JOURNAL_CHECKSUM change
  ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize
  ext4: support read-only images
  ext4: change to use setup_timer() instead of init_timer()
  ext4: reserve codepoints used by the ext4 encryption feature
  jbd2: complain about descriptor block checksum errors