- 05 Mar, 2024 6 commits
-
-
Bitterblue Smith authored
PCI drivers and USB drivers can both use the same function, read_efuse_byte(), and they can call it directly. rtl8192de was the only user. Tested only with the upcoming rtl8192du driver. Signed-off-by:
Bitterblue Smith <rtl8821cerfe2@gmail.com> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/4e2c968d-f25c-4a40-be97-4fdcbdde69cf@gmail.com
-
Bitterblue Smith authored
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just ofdm_fa_cnt. Fixes: 96036123 ("rtw88: 8821c: add false alarm statistics") Signed-off-by:
-
Bitterblue Smith authored
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because of frequent disconnections: Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED bssid=90:55:de:__:__:__ reason=4 locally_generated=1 Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED - Connection to 90:55:de:__:__:__ completed [id=0 id_str=] Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED bssid=90:55:de:__:__:__ reason=4 locally_generated=1 Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED - Connection to 90:55:de:__:__:__ completed [id=0 id_str=] Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED bssid=90:55:de:__:__:__ reason=4 locally_generated=1 This is caused by a mistake in the chip initialisation. This version of the chip requires loading an extra AGC table right after the main one, but the extra table is being loaded at the wrong time, in rtw_chip_board_info_setup(). Move the extra AGC table loading to the right place, in rtw_phy_load_tables(). The rtw_chip_board_info_setup() can only do "software" things, and rtw_phy_load_tables() can really do IO. Fixes: 5d6651fe ("rtw88: 8821c: support RFE type2 wifi NIC") Signed-off-by:
-
Bitterblue Smith authored
Clear bit 8 of REG_SYS_STATUS1 after MAC power on. Without this, some RTL8821CU and RTL8811CU cannot connect to any network: Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to 90:55:de:__:__:__ (try 1/3) Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to 90:55:de:__:__:__ (try 2/3) Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to 90:55:de:__:__:__ (try 3/3) Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with 90:55:de:__:__:__ timed out The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do it for all three types of chips. Tested with RTL8811CU (Tenda U9 V2.0). Signed-off-by:
-
Bitterblue Smith authored
RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after reading and writing certain addresses. Without this, the firmware upload fails approximately more than 50% of the time. Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU but without Bluetooth. Fixes: a82dfd33 ("wifi: rtw88: Add common USB chip support") Signed-off-by:
-
Nick Morrow authored
Add VID/PIDs that are known to be missing for this driver. Removed /* 8811CU */ and /* 8821CU */ as they are redundant since the file is specific to those chips. Removed /* TOTOLINK A650UA v3 */ as the manufacturer. It has a REALTEK VID so it may not be specific to this adapter. Verified and tested. Cc: stable@vger.kernel.org Signed-off-by:
Nick Morrow <morrownr@gmail.com> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Acked-by:
-
- 04 Mar, 2024 30 commits
-
-
Johannes Berg authored
If a link is deactivated, we really cannot sustain any TDLS connections on that link any more. With the API now changed, fix this issue and remove TDLS connections. Reviewed-by:
Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com> Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Link: https://msgid.link/20240228095719.a7dd812c37bf.I3474dbde79e9e7a539d47f6f81f32e6c3e459080@changeidSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
If a link does CSA, or if it changes SMPS mode, we need to drop the TDLS peers, but we really should drop them only on the affected link. Fix that. Reviewed-by:
-
Johannes Berg authored
Unify all the CSA handling, including handling of a beacon after the CSA, into ieee80211_sta_process_chanswitch(). The CRC of the beacon will change due to changes in the CSA/ECSA elements, so there's really no need to have the 'beacon after CSA' handling before the CRC processing or to change the beacon_crc_valid value here. Reviewed-by:
-
Johannes Berg authored
When doing CSA in multi-link, there really isn't a need to stop transmissions entirely. Add a feature flag for drivers to indicate they can handle quiet in CSA (be it by parsing themselves, or by implementing drv_pre_channel_switch()), to make that possible. Also clean up the csa_block_tx handling: it clearly cannot handle multi-link due to the way queues are stopped, move it to the sdata. Drivers should be doing it themselves for working properly during CSA in MLO anyway. Also rename it to indicate that it reflects TX was blocked at mac80211. Reviewed-by:
-
Johannes Berg authored
Pass the link conf to the abort_channel_switch driver method so the driver can handle things correctly. Reviewed-by:
-
Johannes Berg authored
For CSA to work correctly in multi-link scenarios, pass the link_id to the relevant callbacks. While at it, unify/deduplicate the tracing for them. Reviewed-by:
-
Johannes Berg authored
If we just want to determine the length of the fragmented data, we basically need the same logic, and really we want it to be _literally_ the same logic, so it cannot be out of sync in any way. Allow calling cfg80211_defragment_element() without an output buffer, where it then just returns the required output size. Also add this to the tests, just to exercise it, using the pre-calculated length to really do the defragmentation, which checks that this is sufficient. Reviewed-by:
Benjamin Berg <benjamin.berg@intel.com> Link: https://msgid.link/20240228095718.6d6565b9e3f2.Ib441903f4b8644ba04b1c766f90580ee6f54fc66@changeidSigned-off-by:
-
Johannes Berg authored
In mac80211 we'll need to look at reduced neighbor report entries for channel switch purposes, so export the iteration function to make that simpler. Reviewed-by:
-
Johannes Berg authored
Rework the data structures to hide element parsing internals from the users. Reviewed-by:
-
Johannes Berg authored
We're always using "scratch + len - pos", so we don't need to subtract here to calculate the remaining length. Remove the unnecessary subtraction. Reviewed-by:
Ilan Peer <ilan.peer@intel.com> Link: https://msgid.link/20240228094902.44e07cfa9e63.I7a9758fb9bc6b726aac49804f2f05cd521bc4128@changeidSigned-off-by:
-
Johannes Berg authored
Using the scratch buffer (without advancing it) here in the mlme.c code seems somewhat wrong, defragment the reconfig multi-link element already when parsing. This might be a bit more work in certain cases, but makes the whole thing more regular. Reviewed-by:
-
Johannes Berg authored
We shouldn't assign elems->ml_basic{,len} before defragmentation, and we don't need elems->ml_reconf{,len} at all since we don't do defragmentation. Clean that up a bit. This does require always defragmention even when it may not be needed, but that's easier to reason about. Reviewed-by: -
Johannes Berg authored
Given the prior changes to ieee80211_mle_size_ok(), we can now pass NULL to for_each_mle_subelement(), so no longer need to check for that here explicitly. Reviewed-by:
-
Johannes Berg authored
We sometimes need to check if a link is active, and this is complicated by the fact that active_links has no bits set when the vif isn't (acting as) an MLD. Add a small new helper ieee80211_vif_link_active() to make that a bit easier, and use it in a few places. Reviewed-by:
-
Johannes Berg authored
At this point, since it's taken from elems->ml_basic which is stored only if it's of type basic, we don't really need to check again if it's basic. Reviewed-by:
-
Johannes Berg authored
The scratch_pos update here was lost after defrag, so any other uses of the scratch buffer might overwrite it. Fixes: a286de1a ("wifi: mac80211: Rename multi_link") Reviewed-by:
-
Ilan Peer authored
The CQM handling did not consider the MLO case and thus notified a not-existing link with the CQM change. To fix this, propagate the CQM notification to all the active links (handling both the non-MLO and MLO cases). TODO: this currently propagates the same configuration to all links regardless of the band. This might not be the correct approach as different links might need to be configured with different values. Signed-off-by:
-
Ilan Peer authored
When a beacon is received use it to update the BSS table regardless of the scanning state. Do so only when there are active non-monitor interfaces. Also, while at it, in any case accept beacons only with broadcast address. Reviewed-by:
-
Shaul Triebitz authored
In MLO, we need the link id in the GTK key to be given by the driver after rekeying in wowlan, so add that. Signed-off-by:
Shaul Triebitz <shaul.triebitz@intel.com> Reviewed-by:
-
Johannes Berg authored
It's confusing to see decimal, e.g. 20, here. Printing the flags in hex (0x14 == 20) is much clearer. Reviewed-by:
-
Johannes Berg authored
In the association request, we make some parameters depend on the AP's HT/VHT information. This was broken by my code because it no longer filled that information, making it all zero. For HT that meant we wouldn't reduce our capabilities to 20 MHz if needed, and for VHT we lost beamforming capabilities. Fix this. It seems like it may even have been broken for all but the assoc link before. Fixes: 310c8387 ("wifi: mac80211: clean up connection process") Reviewed-by:
-
Johannes Berg authored
When a link doesn't have VHT capability, before the rework we'd have set IEEE80211_CONN_DISABLE_VHT, but now with the linear progression of 'mode', we no longer have that. Add an explicit check for VHT being supported, so we don't add a zeroed VHT capabilities element where it shouldn't be. Fixes: 310c8387 ("wifi: mac80211: clean up connection process") Reviewed-by:
-
Aditya Kumar Singh authored
Currently whenever link AP is started, netif_carrier_up() function is called and whenever it is brought down, netif_carrier_down() function is called. However, with MLO, all the links of the same MLD would use the same netdev. Hence there is no need to indicate for each link up/down. Also, calling it down when only one of the links went down is not desirable. Add changes to call the netif_carrier_up() function only when first link is brought up. Similarly, add changes to call the netif_carrier_down() function only when last link is brought down. In order to check the number of beaconing links in the given interface, introduce a new helper function ieee80211_num_beaconing_links(). Signed-off-by:
Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://msgid.link/20240227042251.1511122-3-quic_adisi@quicinc.comSigned-off-by:
-
Rameshkumar Sundaram authored
Currently while stopping a link AP, all keys from the interface were removed. However with MLO there is a requirement to free only the link keys. Add changes to remove keys which are associated with the link AP which is going to be stopped. Signed-off-by:
Rameshkumar Sundaram <quic_ramess@quicinc.com> Signed-off-by:
-
Johannes Berg authored
If it looks like there's another subframe in the A-MSDU but the header isn't fully there, we can end up reading data out of bounds, only to discard later. Make this a bit more careful and check if the subframe header can even be present. Reported-by: syzbot+d050d437fe47d479d210@syzkaller.appspotmail.com Link: https://msgid.link/20240226203405.a731e2c95e38.I82ce7d8c0cc8970ce29d0a39fdc07f1ffc425be4@changeidSigned-off-by:
-
Takashi Iwai authored
A few models require *.pnvm files while we don't declare them via MODULE_FIRMWARE(). This resulted in the breakage of WiFi on the system that relies on the information from modinfo (e.g. openSUSE installer image). This patch adds those missing MODULE_FIRMWARE() entries for *.pnvm files. type=feature ticket=none Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1207553Signed-off-by:
Takashi Iwai <tiwai@suse.de> Link: https://msgid.link/20240228163837.4320-1-tiwai@suse.de [move to appropriate files] Signed-off-by:
-
Johannes Berg authored
We're currently tracking rx_nss for each station, and that is meant to be initialized to the capability NSS and later reduced by the operating mode notification NSS. However, we're mixing up capabilities and operating mode NSS in the same variable. This forces us to recalculate the NSS capability on operating mode notification RX, which is a bit strange; due to the previous fix I had to never keep rx_nss as zero, it also means that the capa is never taken into account properly. Fix all this by storing the capability value, that can be recalculated unconditionally whenever needed, and storing the operating mode notification NSS separately, taking it into account when assigning the final rx_nss value. Cc: stable@vger.kernel.org Fixes: dd6c064c ("wifi: mac80211: set station RX-NSS on reconfig") Reviewed-by:
-
Johannes Berg authored
We have an nl80211 attribute to mask supported rates from probe responses in scanning, e.g. for use in P2P, but in the refactoring I stopped applying this mask. Restore it. Fixes: 07095d16 ("wifi: mac80211: start building elements in SKBs") Link: https://msgid.link/20240301175451.7ad8ab0bd90c.I46b49e4fc27fe60b75d4559c01104e55ed381c37@changeidSigned-off-by:
-
Johannes Berg authored
If the assoc link doesn't exist yet at this point, we cannot use it yet. This isn't normally the case, but e.g. in case of FT-DS (or just broken userspace) the link might not be set up yet and will only be created later in this function. Check that the link exists. Fixes: 310c8387 ("wifi: mac80211: clean up connection process") Reported-by:
Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/3151f5d0-c18f-413d-b34b-b94f095b947c@moroto.mountainReviewed-by:
-
Johannes Berg authored
My previous patch only initialized match_auth when the ifmgd->auth_data exists, but that was wrong, it should always be set. Fix that. Fixes: 310c8387 ("wifi: mac80211: clean up connection process") Reported-by:
-
- 28 Feb, 2024 4 commits
-
-
Johannes Berg authored
There's a somewhat common pattern of using FIELD_PREP() even for single bits, e.g. cmd->info1 |= FIELD_PREP(HTT_SRNG_SETUP_CMD_INFO1_RING_FLAGS_MSI_SWAP, !!(params.flags & HAL_SRNG_FLAGS_MSI_SWAP)); which might as well be written as if (params.flags & HAL_SRNG_FLAGS_MSI_SWAP) cmd->info1 |= HTT_SRNG_SETUP_CMD_INFO1_RING_FLAGS_MSI_SWAP; (since info1 is fully initialized to start with), but in a long chain of FIELD_PREP() this really seems fine. However, it triggers a sparse warning, in the check in the macro for whether a constant value fits into the mask, as this contains a "& (_val)". In this case, this really is always intentional, so just suppress the warning by adding "0+" to the expression, indicating explicitly that this is correct. Signed-off-by: -
Shiji Yang authored
Moving struct ieee80211_sta *sta variable definition to the front of the code to fix the ISO C90 forbids mixed declarations and code warning. Fixes: 43532c05 ("wifi: rtl8xxxu: support multiple interfaces in set_aifs()") Signed-off-by:
Shiji Yang <yangshiji66@outlook.com> Reviewed-by:
-
Johannes Berg authored
This code wants to compare the obtained value, but as it also has a special type for register addresses to find places doing such compares and calculations wrong, we need explicit casts here to silence sparse. Signed-off-by:
-
Johannes Berg authored
Clearly writing __le32 was intended here, so just put the right casts into the code to silence sparse about it. Signed-off-by:
-
