- 26 Oct, 2019 5 commits
-
-
David S. Miller authored
Grygorii Strashko says: ==================== net: phy: dp83867: enable robust auto-mdix Patch 1 - improves link detection when dp83867 PHY is configured in manual mode by enabling CFG3[9] Robust Auto-MDIX option. Patch 2 - is minor optimization. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Move DT parsing code to probe dp83867_probe() as it's one time operation. Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Grygorii Strashko authored
The link detection timeouts can be observed (or link might not be detected at all) when dp83867 PHY is configured in manual mode (speed/duplex). CFG3[9] Robust Auto-MDIX option allows to significantly improve link detection in case dp83867 is configured in manual mode and reduce link detection time. As per DM: "If link partners are configured to operational modes that are not supported by normal Auto MDI/MDIX mode (like Auto-Neg versus Force 100Base-TX or Force 100Base-TX versus Force 100Base-TX), this Robust Auto MDI/MDIX mode allows MDI/MDIX resolution and prevents deadlock." Hence, enable this option by default as there are no known reasons not to do so. Signed-off-by:
-
Vincent Prince authored
There is networking hardware that isn't based on Ethernet for layers 1 and 2. For example CAN. CAN is a multi-master serial bus standard for connecting Electronic Control Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes of payload. Frame corruption is detected by a CRC. However frame loss due to corruption is possible, but a quite unusual phenomenon. While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of legacy protocols on top of CAN, which are not build with flow control or high CAN frame drop rates in mind. When using fq_codel, as soon as the queue reaches a certain delay based length, skbs from the head of the queue are silently dropped. Silently meaning that the user space using a send() or similar syscall doesn't get an error. However TCP's flow control algorithm will detect dropped packages and adjust the bandwidth accordingly. When using fq_codel and sending raw frames over CAN, which is the common use case, the user space thinks the package has been sent without problems, because send() returned without an error. pfifo_fast will drop skbs, if the queue length exceeds the maximum. But with this scheduler the skbs at the tail are dropped, an error (-ENOBUFS) is propagated to user space. So that the user space can slow down the package generation. On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH during compile time, or set default during runtime with sysctl net.core.default_qdisc (see [1]), we get a bad user experience. In my test case with pfifo_fast, I can transfer thousands of million CAN frames without a frame drop. On the other hand with fq_codel there is more then one lost CAN frame per thousand frames. As pointed out fq_codel is not suited for CAN hardware, so this patch changes attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices. During transition of a netdev from down to up state the default queuing discipline is attached by attach_default_qdiscs() with the help of attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to attach the pfifo_fast (pfifo_fast_ops) if the network device type is "ARPHRD_CAN". [1] https://github.com/systemd/systemd/issues/9194Suggested-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Vincent Prince <vincent.prince.fr@gmail.com> Acked-by:
Dave Taht <dave.taht@gmail.com> Signed-off-by:
-
Hayes Wang authored
Fix the pointer rtl_fw->fw would be used before checking in rtl8152_apply_firmware() that causes the following kernel oops. Unable to handle kernel NULL pointer dereference at virtual address 00000002 pgd = (ptrval) [00000002] *pgd=00000000 Internal error: Oops: 5 [#1] PREEMPT SMP ARM Modules linked in: CPU: 0 PID: 131 Comm: kworker/0:2 Not tainted 5.4.0-rc1-00539-g9370f2d0 #6788 Hardware name: SAMSUNG EXYNOS (Flattened Device Tree) Workqueue: events_long rtl_hw_phy_work_func_t PC is at rtl8152_apply_firmware+0x14/0x464 LR is at r8153_hw_phy_cfg+0x24/0x17c pc : [<c064f4e4>] lr : [<c064fa18>] psr: a0000013 sp : e75c9e60 ip : 60000013 fp : c11b7614 r10: e883b91c r9 : 00000000 r8 : fffffffe r7 : e883b640 r6 : fffffffe r5 : fffffffe r4 : e883b640 r3 : 736cfe7c r2 : 736cfe7c r1 : 000052f8 r0 : e883b640 Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 6640006a DAC: 00000051 Process kworker/0:2 (pid: 131, stack limit = 0x(ptrval)) Stack: (0xe75c9e60 to 0xe75ca000) ... [<c064f4e4>] (rtl8152_apply_firmware) from [<c064fa18>] (r8153_hw_phy_cfg+0x24/0x17c) [<c064fa18>] (r8153_hw_phy_cfg) from [<c064e784>] (rtl_hw_phy_work_func_t+0x220/0x3e4) [<c064e784>] (rtl_hw_phy_work_func_t) from [<c0148a74>] (process_one_work+0x22c/0x7c8) [<c0148a74>] (process_one_work) from [<c0149054>] (worker_thread+0x44/0x520) [<c0149054>] (worker_thread) from [<c0150548>] (kthread+0x130/0x164) [<c0150548>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20) Exception stack(0xe75c9fb0 to 0xe75c9ff8) ... Fixes: 9370f2d0 ("r8152: support request_firmware for RTL8153") Reported-by:
Marek Szyprowski <m.szyprowski@samsung.com> Tested-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
- 24 Oct, 2019 30 commits
-
-
David S. Miller authored
Madalin Bucur says: ==================== DPAA Ethernet changes v3: add newline at the end of error messages v2: resending with From: field matching signed-off-by Here's a series of changes for the DPAA Ethernet, addressing minor or unapparent issues in the codebase, adding probe ordering based on a recently added DPAA QMan API, removing some redundant code. ==================== Signed-off-by: -
Madalin Bucur authored
Newline was missing at the end of the error message. Signed-off-by:
Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by:
-
Madalin Bucur authored
Remove unused struct member second_largest_buf_size. Also, an out of bounds access would have occurred in the removed code if there was only one buffer pool in use. Signed-off-by:
-
Madalin Bucur authored
The DPAA Ethernet driver is using the FMan MAC as the device for DMA mapping. This is not actually correct, as the real DMA device is the FMan port (the FMan Rx port for reception and the FMan Tx port for transmission). Changing the device used for DMA mapping to the Fman Rx and Tx port devices. Signed-off-by:
Laurentiu Tudor <laurentiu.tudor@nxp.com> Signed-off-by:
-
Laurentiu Tudor authored
Add an API that retrieves the 'struct device' that the specified FMan port probed against. The new API will be used in a subsequent patch that corrects the DMA devices used by the dpaa_eth driver. Signed-off-by:
-
Madalin Bucur authored
Condition was previously checked, removing duplicate code. Signed-off-by:
-
Laurentiu Tudor authored
If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will cause a boot crash. Add predictability in the probing order by deferring the Ethernet driver probe after QBMan and portals by using the recently introduced QBMan APIs. Signed-off-by:
-
Laurentiu Tudor authored
The liodn base registers are specific to PAMU based NXP systems and are reserved on SMMU based ones. Don't access them unless PAMU is compiled in. Signed-off-by:
-
David S. Miller authored
Igor Russkikh says: ==================== net: aquantia: PTP support for AQC devices This patchset introduces PTP feature support in Aquantia AQC atlantic driver. This implementation is a joined effort of aquantia developers: Egor is the main designer and driver/firmware architect on PTP, Sergey and Dmitry are included as co-developers. Dmitry also helped me in the overall patchset preparations. Feature was verified on AQC hardware with testptp tool, linuxptp, gptp and with Motu hardware unit. version3 updates: - Review comments applied: error handling, various fixes version2 updates: - Fixing issues from Andrew's review: replacing self with ptp var name, making ptp_clk_offset a field in the ptp instance. devm_kzalloc advice is actually non applicable, because ptp object gets created/destroyed on each network device close/open and it should not be linked with dev lifecycle. - Rearranging commit authorship, adding Egor as a ptp module main maintainer - Fixing kbuild 32bit division issues ==================== Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
-
Igor Russkikh authored
PTP implementation is designed and maintained by Egor Pomozov, adding him as this module maintainer. Egor is the author of the core functionality and the architect, and is to be contacted for all Aquantia PTP/AVB functionality. Signed-off-by:
Egor Pomozov <epomozov@marvell.com> Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
-
Dmitry Bezrukov authored
Depending on FW configuration we can manage from 0 to 3 PINs for periodic output and from 0 to 1 ext ts PIN for getting TS for external event. Ext TS PIN functionality is implemented via periodic timestamps polling directly from PHY, because right now there is now way to receive the PIN trigger interrupt from phy. The polling interval is 15 milliseconds. Co-developed-by:
Pavel Belous <pavel.belous@aquantia.com> Signed-off-by:
Dmitry Bezrukov <dmitry.bezrukov@aquantia.com> Signed-off-by:
-
Dmitry Bezrukov authored
GPIO PIN control and access is done by direct phy manipulation. Here we add an aq_phy module which is able to access phy registers via MDIO access mailbox. Access is controlled via HW semaphore. Co-developed-by:
Nikita Danilov <nikita.danilov@aquantia.com> Signed-off-by:
-
Egor Pomozov authored
Ethtool callback with basic information on what PTP features are supported by the device. Signed-off-by:
Sergey Samoilenko <sergey.samoilenko@aquantia.com> Signed-off-by:
-
Egor Pomozov authored
Here we add support for PTP specific IOCTLs of HW timestamp get/set. These will use filters to configure flows onto the required queue ids. Co-developed-by:
-
Dmitry Bezrukov authored
We implement HW filter reservation for PTP traffic. Special location in filters table is marked as reserved, because incoming ptp traffic should be directed only to PTP designated queue. This way HW will do PTP timestamping and proper processing. Co-developed-by:
-
Egor Pomozov authored
Here we do alloc/free IRQs for PTP rings. We also implement processing of PTP packets on TX and RX sides. Signed-off-by:
-
Dmitry Bezrukov authored
Checkpatch and styling fixes on parts of code touched by ptp Signed-off-by:
-
Egor Pomozov authored
Add implementations of PTP rings alloc/free. PTP desing on this device uses two separate rings on a separate traffic class for traffic rx/tx. Third ring (hwts) is not a traffic ring, but is used only to receive timestamps of the transmitted packets. Signed-off-by:
-
Egor Pomozov authored
Basic HW functions implemented for adjusting frequency, adjusting time, getting and setting time. With these callbacks we now do register ptp clock in the system. Firmware interface parts are defined for PTP requests and interactions. Enable/disable PTP counters in HW on clock register/unregister. Signed-off-by:
-
Dmitry Bezrukov authored
Make some other bit-enums more clear about positioning, this helps on debugging and development Signed-off-by:
-
Egor Pomozov authored
Here we add basic function for PTP clock register/unregister. We also declare FW/HW capability bits used to control PTP feature on device. PTP device is created if network card has appropriate FW that has PTP enabled in config. HW supports timestamping for PTPv2 802.AS1 and PTPv2 IPv4 UDP packets. It also supports basic PTP callbacks for getting/setting time, adjusting frequency and time as well. Signed-off-by:
-
YueHaibing authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/usb/lan78xx.c:3995:6: warning: variable event set but not used [-Wunused-but-set-variable] It is never used, so can be removed. Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Update main pool computation and pool size limits Petr says: In Spectrum ASICs, the shared buffer is an area of memory where packets are kept until they can be transmitted. There are two resources associated with shared buffer size: cap_total_buffer_size and cap_guaranteed_shared_buffer. So far, mlxsw has been using the former as a limit when validating shared buffer pool size configuration. However, the total size also includes headrooms and reserved space, which really cannot be used for shared buffer pools. Patch #1 mends this and has mlxsw use the guaranteed size. To configure default pool sizes, mlxsw has historically hard-coded one or two smallish pools, and one "main" pool that took most of the shared buffer (that would be pool 0 on ingress and pool 4 on egress). During the development of Spectrum-2, it became clear that the shared buffer size keeps shrinking as bugs are identified and worked around. In order to prevent having to tweak the size of pools 0 and 4 to catch up with updates to values reported by the FW, patch #2 changes the way these pools are set. Instead of hard-coding a fixed value, the main pool now takes whatever is left from the guaranteed size after the smaller pool(s) are taken into account. ==================== Signed-off-by: -
Petr Machata authored
Instead of hard-coding the size of the largest pool, calculate it from the reported guaranteed shared buffer size and sizes of other pools (currently only the CPU port pool). Signed-off-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Petr Machata authored
There are two resources associated with shared buffer size: cap_total_buffer_size, and cap_guaranteed_shared_buffer. So far, mlxsw has been using the former as a limit to determine how large a pool size is allowed to be. However, the total size also includes headrooms and reserved space, which really cannot be used for shared buffer pools. Therefore convert mlxsw to use the latter resource as a limit. Adjust hard-coded pool sizes to be the guaranteed size minus 256000 bytes for CPU port pool. On Spectrum-1 that actually leads to an increase. A follow-up patch will have this size calculated automatically. Signed-off-by:
-
Heiner Kallweit authored
Setting PCI_EXP_DEVCTL_NOSNOOP_EN for certain chip versions had been added to the vendor driver more than 10 years ago, and copied from there to r8169. It has been removed from the vendor driver meanwhile and I think we can safely remove this too. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
David S. Miller authored
Tao Ren says: ==================== net: phy: support 1000Base-X auto-negotiation for BCM54616S This patch series aims at supporting auto negotiation when BCM54616S is running in 1000Base-X mode: without the patch series, BCM54616S PHY driver would report incorrect link speed in 1000Base-X mode. Patch #1 (of 3) modifies assignment to OR when dealing with dev_flags in phy_attach_direct function, so that dev_flags updated in BCM54616S PHY's probe callback won't be lost. Patch #2 (of 3) adds several genphy_c37_* functions to support clause 37 1000Base-X auto-negotiation, and these functions are called in BCM54616S PHY driver. Patch #3 (of 3) detects BCM54616S PHY's operation mode and calls according genphy_c37_* functions to configure auto-negotiation and parse link attributes (speed, duplex, and etc.) in 1000Base-X mode. ==================== Signed-off-by: -
Tao Ren authored
The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly because genphy functions are designed for copper links, and 1000Base-X (clause 37) auto negotiation needs to be handled differently. This patch enables 1000Base-X support for BCM54616S by customizing 3 driver callbacks, and it's verified to be working on Facebook CMM BMC platform (RGMII->1000Base-KX): - probe: probe callback detects PHY's operation mode based on INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX Control register. - config_aneg: calls genphy_c37_config_aneg when the PHY is running in 1000Base-X mode; otherwise, genphy_config_aneg will be called. - read_status: calls genphy_c37_read_status when the PHY is running in 1000Base-X mode; otherwise, genphy_read_status will be called. Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and 100Base-FX support is not available as of now. Signed-off-by:Tao Ren <taoren@fb.com> Acked-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
-
Heiner Kallweit authored
This patch adds support for clause 37 1000Base-X auto-negotiation. Signed-off-by:
René van Dorst <opensource@vdorst.com> Reviewed-by:
-
Tao Ren authored
Modify the assignment to OR when dealing with phydev->dev_flags in phy_attach_direct function, and this is to make sure dev_flags set in driver's probe callback won't be lost. Suggested-by:
-
- 22 Oct, 2019 5 commits
-
-
Eric Dumazet authored
Since commit 342db221 ("sched: Call skb_get_hash_perturb in sch_fq_codel") we no longer need anything from this file. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com>
-
Jakub Kicinski authored
Vivien Didelot says: ==================== The dsa_switch structure represents the physical switch device itself, and is allocated by the driver. The dsa_switch_tree and dsa_port structures represent the logical switch fabric (eventually composed of multiple switch devices) and its ports, and are allocated by the DSA core. This branch lists the logical ports directly in the fabric which simplifies the iteration over all ports when assigning the default CPU port or configuring the D in DSA in drivers like mv88e6xxx. This also removes the unique dst->cpu_dp pointer and is a first step towards supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation. Because the dsa_port structures are not tied to the dsa_switch structure anymore, we do not need to provide an helper for the drivers to allocate a switch structure. Like in many other subsystems, drivers can now embed their dsa_switch structure as they wish into their private structure. This will be particularly interesting for the Broadcom drivers which were currently limited by the dynamically allocated array of DSA ports. The series implements the list of dsa_port structures, makes use of it, then drops dst->cpu_dp and the dsa_switch_alloc helper. ==================== Signed-off-by: -
Vivien Didelot authored
Now that ports are dynamically listed in the fabric, there is no need to provide a special helper to allocate the dsa_switch structure. This will give more flexibility to drivers to embed this structure as they wish in their private structure. Signed-off-by:
Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by:
-
Vivien Didelot authored
Allocate the struct dsa_port the first time it is accessed with dsa_port_touch, and remove the static dsa_port array from the dsa_switch structure. Signed-off-by:
-
Vivien Didelot authored
Like the dsa_switch_tree structures, the dsa_port structures will be allocated on switch registration. The SJA1105 driver is the only one accessing the dsa_port structure after the switch allocation and before the switch registration. For that reason, move switch registration prior to assigning the priv member of the dsa_port structures. Signed-off-by:
-
