Use chan->hs_hcon instead of lookup by dst address.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Postpone sending A2MP Create Phylink Response until we got successful
HCI Command Complete after HCI Write Remote AMP Assoc.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch removes srej_queue_next from include/net/bluetooth/l2cap.h as it
is not used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch removes unnecessary include of <net/bluetooth/l2cap.h>
in bluetooth/bnep/core.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch is an enhacement to mwifiex_pcie driver to use
map/unmap PCI memory APIs. This reduces one memcpy each in TX
path and RX path, and enhances throughput.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds handler to clean PCIe TX rings after disconnect
or bss stop is called for PCIe based mwifiex driver.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch uses pci_alloc_consistent and pci_free_consistent
APIs for mwifiex_pcie driver. Consistent DMA memory is allocated
for TX, RX and event rings. Command buffer and command response
buffer also uses map/unmap memory APIs to download commands and
get command responses.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for init_fw_port handler for PCIe
interface, which resets RXBD read pointer for PCIe.
This fixes issue where RX doesn't work until some TX from
driver happens.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug for few instances where PCIe interrupt
status variable is accessed without holding spin lock.
This can result into missing interrupts.

Fix this by copying interrupt status to a local variable and
then using it for calling specific routine.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The new name better matches the use of this variable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This member is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some cores do not have a IRQ assigned and some do not support when an
IRQ is assigned to them, this is now handled and printed out in the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The assignment of the IRQs to the cores of the chips by iterating over
the cores is complicated and causes problems with SoC like the BCM4706
with two GMAC core where just one should get a dedicated IRQ number.
Now the code assigns the same IRQs to the cores as the code from the
Broadcom SDK does. If the SoC is not know the current assigned IRQs are
only read out and an error message is printed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This bcma_find_core_unit() is needed by the mips driver in the next
patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

New firmware is required to support
a) Add support for additional ampdu streams
b) Handle corresponding watchdog events to destroy ampdu streams

Bumping firmware API version by one.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, command path waits till all the tx host queues
are empty. Whenever watchdog event is raised, firmware
expects driver to destroy ampdu queues immediately.

This requires corresponding commands i.e.
mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be
sent without waiting for the tx queues to be completely
empty.

Use "watchdog_event_pending" to ensure the above mentioned
two commands are sent down immediately.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

With more ampdu streams, we need to handle watchdog
events for the new ampdu streams. Handle these
events appropriately.

Earlier mwl8k_cmd_get_watchdog_bitmap used to return
only one stream index and hence bitwise operations
on the return value were not required. Now the function
returns a bitmap with different bits are mapped with
different stream indices.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, mwl8k_ampdu_stream is passed as one of the
argument to the function mwl8k_destroy_ba. Instead of
this pass only the stream index. This will be helpful
during watchdog event handling when bitmap of stream
indices are received.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently, we have 2 ampdu streams that can be created
simultaneously. Firmware is capable of supporting
additional streams. Add support to use these streams.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set ACK policy to NORMAL when its not going to
be an AMPDU packet.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Ampdu stream index can be derived from stream->idx.
So we no longer need stream->txq_idx, hence removing it.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is not enabled for any chip and is unused.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds support for parsing WMM IEs from hostapd
and setting them to FW via sys configure command.

Patch also sets wiphy flag to advertise AP uAPSD support.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is observed that same htcapinfo ie is included in beacon for
HT20, HT40+ and HT40- ibss networks. This patch makes sure that
we will not advertise 40Mhz flags while creating/joining ibss
network in HT20 mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We know 'firmware' is non-NULL from the beginning of mwifiex_prog_fw_w_helper,
remove all !firmware paths from the rest of the function.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If pci_set_dma_mask() or pci_set_consistent_dma_mask() fails in p54p_probe(),
it breaks off initialization, deallocates all resources, but returns zero.
Similar issue is if check for returned value of pci_resource_len() fails.

The patch implements proper error code propagation.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

On interface up dongle gets inialized. Move UP command to common
routine and update these common init routines using ifp.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Netdev xmit routine brcfm_netdev_start_xmit was defined
incorrectly and used wrong return codes. Always eat the
packet and return ok. Remove drvr_up check since it is not
relevant.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CDC errors are retained. However, it is never used so it can
be removed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Stumbled into a curly braces used for if statement with only
one conditional statement. Removing them.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The header of the ethernet packet is processed conditionally, but
the check is wrong as it checks skb length is at least ETH_ALEN. It
should check it is at least sizeof struct ethhdr instead.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver had some global definitions in dhd.h to map event
identifiers to event names. With redesign of firmware event
processing this has all moved to fweh module so these definitions
can be removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

CDC debug is partly done with TRACE and partly with CTL, however
CDC hardly ever needs debugging. Use dedicated level CDC and
replace TRACE and CTL in dhd_cdc with that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The use of the function brcmf_proto_hdrpull() is moved to the
common part of the driver and consequently it can be removed
from the bus interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The bus interface provided a wrapper function to pass a single
packet to the common driver part filling a skb queue with one
packet. For clarity the caller now sets up the skb queue and
call the rx bus interface function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Several source files (but not all) define the pr_fmt() macro in exactly
the same way. Instead this commit defines it in a header file so driver
logging is consistent.

Cc: Joe Perches <joe@perches.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>