The MT6315 is a regulator found on boards based on MediaTek MT8192 and
probably other SoCs. It connects as a slave to SoC using SPMI.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1612678457-11548-3-git-send-email-hsin-hsiung.wang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add device tree binding information for MT6315 regulator driver.
Example bindings for MT6315 are added.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1612678457-11548-2-git-send-email-hsin-hsiung.wang@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add charger-supply optional property to enable charging control.
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210130172747.2022977-2-timon.baetz@protonmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Calling the disable_irq() from irq handler might be a bad idea as
disable_irq() should wait for handlers to run. I don't see why
this wouldn't deadlock in wait_event waiting for the threaded
handler to complete.

Use disable_irq_nosync() instead.

Fixes: 390af53e ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: AngeloGioacchino Del Regno  <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/f2c4c88d90bf7473e1b84b8a99b7b33d7a081764.1612249657.git.matti.vaittinen@fi.rohmeurope.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch sets ramp_delay for bucks to the max value given by the
datasheet.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/60d8eb8feefd26380cc9c6503f835e569be90465.camel@googlemail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.

Commit ff268b56 ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.

Commit c33d4423 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:

[   26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!

There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.

Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.

Fixes: c33d4423 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch adds suspend/resume support so that it is possible to
configure the LDOs and BUCKs as on or off during suspend phase as
well as to configure suspend specific voltages.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/4c2e79d4fa96befdc9a6c59c3ff27b0a34f9fb56.camel@googlemail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Make regulator_sync_voltage() to re-balance voltage state of a coupled
regulators instead of changing the voltage directly.

Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210122174311.28230-1-digetx@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The device node reference obtained with of_get_child_by_name() should be
dropped on error paths.

Fixes: 26aec009 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121155914.48034-1-krzk@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The regulators from PMC8180 and PMC8180C exposed by the RPMH in the
Qualcomm SC8180X seems to be the same as PM8150 and PM8150L. Add
compatibles for the two new PMICs and reuse the definition of the
existing PMICs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120224901.1611232-2-bjorn.andersson@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Add RPMH regulator compatibles for two of the PMIC variants used on the
SC8180x platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120224901.1611232-1-bjorn.andersson@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Call of_node_put() to drop references of regulators_np and reg_np before
returning error code.

Fixes: 9ae5cc75 ("regulator: s5m8767: Pass descriptor instead of GPIO number")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121032756.49501-1-bianpan2016@163.comSigned-off-by: Mark Brown <broonie@kernel.org>

The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.

Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210120151307.1726876-1-arnd@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Really implement Qualcomm LAB/IBB regulators" from AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>:

Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.

In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.

With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.

Changes in v4:
 - Remove already applied commit
 - Add commit to switch to regulator_{list,map}_voltage_linear
   which in v3 got squashed in the commit that got removed in v4.

Changes in v3:
 - Improved check for PBS disable and short-circuit condition:
   during the testing of short-circuit, coincidentally another
   register reading zero on the interesting bit was probed,
   which didn't trigger a malfunction of the SC logic, but was
   also wrong.
   After the change, the short-circuit test was re-done in the
   same way as described in the commit that is implementing it.
 - From Bjorn Andersson review:
   - Improved documentation about over-current and short-circuit
     protection in the driver
   - Improved maintainability of qcom_labibb_sc_recovery_worker()
   - Flipped around check for PBS vreg disabled in for loop of
     function labibb_sc_err_handler()
 - From Mark Brown (forgotten in v2):
   - Changed regulator_{list,map}_voltage_linear_range usages to
     regulator_{list,map}_voltage_linear (and fixed regulator
     descs to reflect the change).

Changes in v2:
 - From Mark Brown review:
   - Replaced some if branches with switch statements
   - Moved irq get and request in probe function
   - Changed short conditionals to full ones
   - Removed useless check for ocp_irq_requested
 -  Fixed issues with YAML documentation

AngeloGioacchino Del Regno (7):
  regulator: qcom-labibb: Switch voltage ops from linear_range to linear
  regulator: qcom-labibb: Implement current limiting
  regulator: qcom-labibb: Implement pull-down, softstart, active
    discharge
  dt-bindings: regulator: qcom-labibb: Document soft start properties
  regulator: qcom-labibb: Implement short-circuit and over-current IRQs
  dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
  arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP

 .../regulator/qcom-labibb-regulator.yaml      |  30 +-
 arch/arm64/boot/dts/qcom/pmi8998.dtsi         |   8 +-
 drivers/regulator/qcom-labibb-regulator.c     | 720 +++++++++++++++++-
 3 files changed, 735 insertions(+), 23 deletions(-)

--
2.30.0

Decrements the reference count of device node and its child node.

Fixes: dfe7a1b0 ("regulator: AXP20x: Add support for regulators subsystem")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/20210120123313.107640-1-bianpan2016@163.comSigned-off-by: Mark Brown <broonie@kernel.org>

Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
now implemented in the driver: document the interrupts.
This also fixes wrong documentation about the SCP interrupt for LAB.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-7-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Document properties to configure soft start and discharge resistor
for LAB and IBB respectively.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-5-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
very important for regulators like LAB and IBB, which are designed to
provide from very small to relatively big amounts of current to the
device (normally, a display).

Now that this regulator supports both voltage setting and current
limiting in this driver, to me it looked like being somehow essential
to provide support for SCP and OCP, for two reasons:
1. SCP is a drastic measure to prevent damaging "more" hardware in
   the worst situations, if any was damaged, preventing potentially
   drastic issues;
2. OCP is a great way to protect the hardware that we're powering
   through these regulators as if anything bad happens, the HW will
   draw more current than expected: in this case, the OCP interrupt
   will fire and the regulators will be immediately shut down,
   preventing hardware damage in many cases.

Both interrupts were successfully tested in a "sort-of" controlled
manner, with the following methodology:

Short-Circuit Protection (SCP):
1. Set LAB/IBB to 4.6/-1.4V, current limit 200mA/50mA;
2. Connect a 10 KOhm resistor to LAB/IBB by poking the right traces
   on a FxTec Pro1 smartphone for a very brief time (in short words,
   "just a rapid touch with flying wires");
3. The Short-Circuit protection trips: IRQ raises, regulators get
   cut. Recovery OK, test repeated without rebooting, OK.

Over-Current Protection (OCP):
1. Set LAB/IBB to the expected voltage to power up the display of
   a Sony Xperia XZ Premium smartphone (Sharp LS055D1SX04), set
   current limit to LAB 200mA, IBB 50mA (the values that this
   display unit needs are 200/800mA);
2. Boot the kernel: OCP fires. Recovery never happens because
   the selected current limit is too low, but that's expected.
   Test OK.

3. Set LAB/IBB to the expected current limits for XZ Premium
   (LAB 200mA, IBB 800mA), but lower than expected voltage,
   specifically LAB 5.4V, IBB -5.6V (instead of 5.6, -5.8V);
4. Boot the kernel: OCP fires. Recovery never happens because
   the selected voltage (still in the working range limits)
   is producing a current draw of more than 200mA on LAB.
   Test OK.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-6-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Soft start is required to avoid inrush current during LAB ramp-up and
IBB ramp-down, protecting connected hardware to which we supply voltage.

Since soft start is configurable on both LAB and IBB regulators, it
was necessary to add two DT properties, respectively "qcom,soft-start-us"
to control LAB ramp-up and "qcom,discharge-resistor-kohms" to control
the discharge resistor for IBB ramp-down, which obviously brought the
need of implementing a of_parse callback for both regulators.

Finally, also implement pull-down mode in order to avoid unpredictable
behavior when the regulators are disabled (random voltage spikes etc).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-4-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

LAB and IBB regulators can be current-limited by setting the
appropriate registers, but this operation is granted only after
sending an unlock code for secure access.

Besides the secure access, it would be possible to use the
regmap helper for get_current_limit, as there is no security
blocking reads, but I chose not to as to avoid having a very
big array containing current limits, especially for IBB.

That said, these regulators support current limiting for:
- LAB (pos): 200-1600mA, with 200mA per step (8 steps),
- IBB (neg):   0-1550mA, with  50mA per step (32 steps).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-3-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The LAB and IBB regulator have just one range and it is useless
to use linear_range ops, as these are used to express multiple
linear ranges.

Switch list_voltage and map_voltage callbacks to *_linear instead.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-2-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Really implement Qualcomm LAB/IBB regulators" from AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>:

Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.

In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.

With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.

Changes in v2:
 - From Mark Brown review:
   - Replaced some if branches with switch statements
   - Moved irq get and request in probe function
   - Changed short conditionals to full ones
   - Removed useless check for ocp_irq_requested
 -  Fixed issues with YAML documentation

AngeloGioacchino Del Regno (7):
  regulator: qcom-labibb: Implement voltage selector ops
  regulator: qcom-labibb: Implement current limiting
  regulator: qcom-labibb: Implement pull-down, softstart, active
    discharge
  dt-bindings: regulator: qcom-labibb: Document soft start properties
  regulator: qcom-labibb: Implement short-circuit and over-current IRQs
  dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
  arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP

 .../regulator/qcom-labibb-regulator.yaml      |  30 +-
 arch/arm64/boot/dts/qcom/pmi8998.dtsi         |   8 +-
 drivers/regulator/qcom-labibb-regulator.c     | 661 +++++++++++++++++-
 3 files changed, 686 insertions(+), 13 deletions(-)

--
2.29.2

Implement {get,set}_voltage_sel, list_voltage, map_voltage with
the useful regulator regmap helpers in order to be able to manage
the voltage of LAB (positive) and IBB (negative) regulators.

In particular, the supported ranges are the following:
- LAB (pos):  4600mV to  6100mV with 100mV stepping,
- IBB (neg): -7700mV to -1400mV with 100mV stepping.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210113194214.522238-2-angelogioacchino.delregno@somainline.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the ternary condition which is a bad coding style
in the kernel

I also remove the defering configuration of the nxp,phase-shift.
The configuration is now done at parsing time. It save some memory
and it's better for comprehension.

I also use the OTP default configuration when the parameter is wrong
or not specified.
I think that it's better to use the default configuration from the chip
than an arbitrary value.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-7-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Use a linear range to describe the voltages of the
bucks 1-6 instead of listing it one by one (via a macro)
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-6-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.

As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-5-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.

As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-4-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

nxp,phase-shift is an enum so use enum format to describe it.
Minimum and maximum values are also wrong.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210114174714.122561-3-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

pf8x00 module build was not documented.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20210114174714.122561-2-adrien.grassein@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

The platform data header was only used to pass platform
data from board files. We now populate the regulators
exclusively from device tree, so the header contents can
be moved into the regulator drivers.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-2-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The struct ab8500_regulator_platform_data was a leftover
since the days before we probed all regulators from the
device tree. The ab8500-ext regulator was the only used,
defining platform data and register intialization that
was never used for anything, a copy of a boardfile no
longer in use.

Delete the ab8500_regulator_platform_data and make the
ab8500-ext regulator reference the regulator init data
in the local file directly. We are 100% device tree
these days.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-1-linus.walleij@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Search for <ncurses.h> in the default header path of HOSTCC

 - Tweak the option order to be kind to old BSD awk

 - Remove 'kvmconfig' and 'xenconfig' shorthands

 - Fix documentation

* tag 'kbuild-fixes-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Documentation: kbuild: Fix section reference
  kconfig: remove 'kvmconfig' and 'xenconfig' shorthands
  lib/raid6: Let $(UNROLL) rules work with macOS userland
  kconfig: Support building mconf with vendor sysroot ncurses
  kconfig: config script: add a little user help
  MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal

Pull SCSI fixes from James Bottomley:
 "This is two driver fixes (megaraid_sas and hisi_sas).

  The megaraid one is a revert of a previous revert of a cpu hotplug fix
  which exposed a bug in the block layer which has been fixed in this
  merge window.

  The hisi_sas performance enhancement comes from switching to interrupt
  managed completion queues, which depended on the addition of
  devm_platform_get_irqs_affinity() which is now upstream via the irq
  tree in the last merge window"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: hisi_sas: Expose HW queues for v2 hw
  Revert "Revert "scsi: megaraid_sas: Added support for shared host tagset for cpuhotplug""

Pull block fixes from Jens Axboe:

 - Missing CRC32 selections (Arnd)

 - Fix for a merge window regression with bdev inode init (Christoph)

 - bcache fixes

 - rnbd fixes

 - NVMe pull request from Christoph:
    - fix a race in the nvme-tcp send code (Sagi Grimberg)
    - fix a list corruption in an nvme-rdma error path (Israel Rukshin)
    - avoid a possible double fetch in nvme-pci (Lalithambika Krishnakumar)
    - add the susystem NQN quirk for a Samsung driver (Gopal Tiwari)
    - fix two compiler warnings in nvme-fcloop (James Smart)
    - don't call sleeping functions from irq context in nvme-fc (James Smart)
    - remove an unused argument (Max Gurtovoy)
    - remove unused exports (Minwoo Im)

 - Use-after-free fix for partition iteration (Ming)

 - Missing blk-mq debugfs flag annotation (John)

 - Bdev freeze regression fix (Satya)

 - blk-iocost NULL pointer deref fix (Tejun)

* tag 'block-5.11-2021-01-10' of git://git.kernel.dk/linux-block: (26 commits)
  bcache: set bcache device into read-only mode for BCH_FEATURE_INCOMPAT_OBSO_LARGE_BUCKET
  bcache: introduce BCH_FEATURE_INCOMPAT_LOG_LARGE_BUCKET_SIZE for large bucket
  bcache: check unsupported feature sets for bcache register
  bcache: fix typo from SUUP to SUPP in features.h
  bcache: set pdev_set_uuid before scond loop iteration
  blk-mq-debugfs: Add decode for BLK_MQ_F_TAG_HCTX_SHARED
  block/rnbd-clt: avoid module unload race with close confirmation
  block/rnbd: Adding name to the Contributors List
  block/rnbd-clt: Fix sg table use after free
  block/rnbd-srv: Fix use after free in rnbd_srv_sess_dev_force_close
  block/rnbd: Select SG_POOL for RNBD_CLIENT
  block: pre-initialize struct block_device in bdev_alloc_inode
  fs: Fix freeze_bdev()/thaw_bdev() accounting of bd_fsfreeze_sb
  nvme: remove the unused status argument from nvme_trace_bio_complete
  nvmet-rdma: Fix list_del corruption on queue establishment failure
  nvme: unexport functions with no external caller
  nvme: avoid possible double fetch in handling CQE
  nvme-tcp: Fix possible race of io_work and direct send
  nvme-pci: mark Samsung PM1725a as IGNORE_DEV_SUBNQN
  nvme-fcloop: Fix sscanf type and list_first_entry_or_null warnings
  ...

Pull io_uring fixes from Jens Axboe:
 "A bit larger than I had hoped at this point, but it's all changes that
  will be directed towards stable anyway. In detail:

   - Fix a merge window regression on error return (Matthew)

   - Remove useless variable declaration/assignment (Ye Bin)

   - IOPOLL fixes (Pavel)

   - Exit and cancelation fixes (Pavel)

   - fasync lockdep complaint fix (Pavel)

   - Ensure SQPOLL is synchronized with creator life time (Pavel)"

* tag 'io_uring-5.11-2021-01-10' of git://git.kernel.dk/linux-block:
  io_uring: stop SQPOLL submit on creator's death
  io_uring: add warn_once for io_uring_flush()
  io_uring: inline io_uring_attempt_task_drop()
  io_uring: io_rw_reissue lockdep annotations
  io_uring: synchronise ev_posted() with waitqueues
  io_uring: dont kill fasync under completion_lock
  io_uring: trigger eventfd for IOPOLL
  io_uring: Fix return value from alloc_fixed_file_ref_node
  io_uring: Delete useless variable ‘id’ in io_prep_async_work
  io_uring: cancel more aggressively in exit_work
  io_uring: drop file refs after task cancel
  io_uring: patch up IOPOLL overflow_flush sync
  io_uring: synchronise IOPOLL on task_submit fail

Pull USB fixes from Greg KH:
 "Here are a number of small USB driver fixes for 5.11-rc3.

  Include in here are:

   - USB gadget driver fixes for reported issues

   - new usb-serial driver ids

   - dma from stack bugfixes

   - typec bugfixes

   - dwc3 bugfixes

   - xhci driver bugfixes

   - other small misc usb driver bugfixes

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
  usb: dwc3: gadget: Clear wait flag on dequeue
  usb: typec: Send uevent for num_altmodes update
  usb: typec: Fix copy paste error for NVIDIA alt-mode description
  usb: gadget: enable super speed plus
  kcov, usb: hide in_serving_softirq checks in __usb_hcd_giveback_urb
  usb: uas: Add PNY USB Portable SSD to unusual_uas
  usb: gadget: configfs: Preserve function ordering after bind failure
  usb: gadget: select CONFIG_CRC32
  usb: gadget: core: change the comment for usb_gadget_connect
  usb: gadget: configfs: Fix use-after-free issue with udc_name
  usb: dwc3: gadget: Restart DWC3 gadget when enabling pullup
  usb: usbip: vhci_hcd: protect shift size
  USB: usblp: fix DMA to stack
  USB: serial: iuu_phoenix: fix DMA from stack
  USB: serial: option: add LongSung M5710 module support
  USB: serial: option: add Quectel EM160R-GL
  USB: Gadget: dummy-hcd: Fix shift-out-of-bounds bug
  usb: gadget: f_uac2: reset wMaxPacketSize
  usb: dwc3: ulpi: Fix USB2.0 HS/FS/LS PHY suspend regression
  usb: dwc3: ulpi: Replace CPU-based busyloop with Protocol-based one
  ...

Pull staging driver fixes from Greg KH:
 "Here are some small staging driver fixes for 5.11-rc3. Nothing major,
  just resolving some reported issues:

   - cleanup some remaining mentions of the ION drivers that were
     removed in 5.11-rc1

   - comedi driver bugfix

   - two error path memory leak fixes

  All have been in linux-next for a while with no reported issues"

* tag 'staging-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: ION: remove some references to CONFIG_ION
  staging: mt7621-dma: Fix a resource leak in an error handling path
  Staging: comedi: Return -EFAULT if copy_to_user() fails
  staging: spmi: hisi-spmi-controller: Fix some error handling paths

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for 5.11-rc3.

  The majority here are fixes for the habanalabs drivers, but also in
  here are:

   - crypto driver fix

   - pvpanic driver fix

   - updated font file

   - interconnect driver fixes

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (26 commits)
  Fonts: font_ter16x32: Update font with new upstream Terminus release
  misc: pvpanic: Check devm_ioport_map() for NULL
  speakup: Add github repository URL and bug tracker
  MAINTAINERS: Update Georgi's email address
  crypto: asym_tpm: correct zero out potential secrets
  habanalabs: Fix memleak in hl_device_reset
  interconnect: imx8mq: Use icc_sync_state
  interconnect: imx: Remove a useless test
  interconnect: imx: Add a missing of_node_put after of_device_is_available
  interconnect: qcom: fix rpmh link failures
  habanalabs: fix order of status check
  habanalabs: register to pci shutdown callback
  habanalabs: add validation cs counter, fix misplaced counters
  habanalabs/gaudi: retry loading TPC f/w on -EINTR
  habanalabs: adjust pci controller init to new firmware
  habanalabs: update comment in hl_boot_if.h
  habanalabs/gaudi: enhance reset message
  habanalabs: full FW hard reset support
  habanalabs/gaudi: disable CGM at HW initialization
  habanalabs: Revise comment to align with mirror list name
  ...