Last caller is gone, so we can remove it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Convert scsi_normalize_sense() and friends to return 'bool'
instead of an integer.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Yoshihiro Yunomae <yoshihiro.yunomae.ez@hitachi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Currently we're only decoding sense extras for tape devices.
And even there only for fixed format sense formats.
As this is of rather limited use in the general case we should
be stop trying to decode sense extras; the tape driver does
its own decoding anyway.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

If scsi_normalize_sense() fails we couldn't decode the sense
buffer, and the scsi_sense_hdr fields are invalid.
For those cases we should rather dump the sense buffer
and not try to decode invalid fields.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

The 53c700 driver would be using scsi_print_sense() in a debug
statement, which was never compiled in. Plus the same information
can get retrieved with logging. So remove it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Update logging messages to use dev_printk() variants for correct
device annotations.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

fas216 returns DID_BAD_TARGET for an incomplete data
transfer. The midlayer uses DID_BAD_TARGET to signal
a non-existing or not reachable target. So we should
rather be using DID_ERROR here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Update acornscsi to use scsi_print_command() instead of the
underscore version and use scmd_printk() in acornscsi_done().
This will add correct device annotations in the resulting message.
And we should be using set_host_byte() for setting the
final result.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

We should be using the standard dev_printk() variants for
sense code printing.

[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Like scmd_printk(), but the device name is passed in as
a string. Can be used by eg ULDs which do not have access
to the scsi_cmnd structure.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Remove all uncommented debugging code and move all
printk() statements over to dev_printk().
And while we're at it we should be doing a whitespace
cleanup, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

sd_done() was calling scsi_print_sense() for a sense code
of 'NO_SENSE'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Unused.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Some SES devices give non-unique Element Descriptors as part of the
Element Descriptor diag page. Since we use these for creating sysfs
entries, they need to be unique. The specification doesn't require
these to be unique.

Eg:
$ sg_ses -p 7 /dev/sg0
  FTS CORP  TXS6_SAS20BPX12   0500
    enclosure services device
Element descriptor In diagnostic page:
  generation code: 0x0
  element descriptor by type list
    Element type: Array device, subenclosure id: 0
      Overall descriptor: ArrayDevicesInSubEnclsr0
      Element 1 descriptor: ArrayDevice00
      Element 2 descriptor: ArrayDevice01
      Element 3 descriptor: ArrayDevice02
      Element 4 descriptor: ArrayDevice03
      Element 5 descriptor: ArrayDevice03
      Element 6 descriptor: ArrayDevice03
      Element 7 descriptor: ArrayDevice03
      Element 8 descriptor: ArrayDevice03
      Element 9 descriptor: ArrayDevice03
      Element 10 descriptor: ArrayDevice03
      Element 11 descriptor: ArrayDevice03
      Element 12 descriptor: ArrayDevice03

Based on http://thread.gmane.org/gmane.linux.scsi/69289. This
version implements James' ideas about the naming convention
Signed-off-by: Markus Stockhausen <stockhausen@collogia.de>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This patch adds a debug_flag parameter that can be set on module load, and allows the DEBUG facility without a module recompile.
Note that now DEBUG 1 is the default with this patch.

Usage: modprobe st debug_flag=1
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Kai M??kisara <kai.makisara@kolumbus.fi>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Further to a January 2013 thread titled: "[PATCH] SG_SCSI_RESET ioctl
should only perform requested operation" by Jeremy Linton a patch (v3)
is presented that expands the existing ioctl to include "no_escalate"
versions to the existing resets. This requires no changes to SCSI low
level drivers (LLDs); it adds several more finely tuned reset options
to the user space. For example:

   /* This call remains the same, with the same escalating semantics
    * if the device (LU) reset fail. That is: on failure to try a
    * target reset and if that fails, try a bus reset, and if that fails
    * try a host (i.e. LLD) reset. */
   val = SG_SCSI_RESET_DEVICE;
   res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);

   /* What follows is a new option introduced by this patch series. Only
    * a device reset is attempted. If that fails then an appropriate
    * error code is provided. N.B. There is no reset escalation. */
   val = SG_SCSI_RESET_DEVICE | SG_SCSI_RESET_NO_ESCALATE;
   res = ioctl(<sg_or_block_fd>, SG_SCSI_RESET, &val);
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Jeremy Linton <jlinton@tributary.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

As sparse correctly pointed out, scsi_partsize should use get_unaligned_le32
to read PC partition tables from disk, as they are little endian.

The result of this bug is that we returned incorrect geometries on big
endian systems when using the scsicam variant.  Which probably doesn't
matter as only old x86 systems every cared about the geometry.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>

Resolve some missing-field-initializers warnings by using
designated initialization.

[hch: W=2 with modern gcc warns about this.  Pretty pointless to me, but
 I'd prefer to keep us warning free]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

The Scsi_Host structure max_lun field is the maximum allowed LUN plus 1. So
a LUN value is invalid if >= max_lun.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

bnx2fc_queuecommand(): when allocating a new io_req, the tgt_lock
spinlock must be locked before calling bnx2fc_cmd_alloc().

The spinlock should also be kept locked until bnx2fc_post_io_req() has
been completed.
If not, a kernel thread may call bnx2fc_process_cq_compl() that extracts
the newly allocated io_req from hba->cmd_mgr->cmds and destroys it while
it is still being used by bnx2fc_post_io_req().

BUG: unable to handle kernel NULL pointer dereference at 000000000000004c
IP: [<ffffffffa03130da>] bnx2fc_init_task+0x6a/0x230 [bnx2fc]
PGD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:02.0/0000:04:00.3/net/eth3/type
CPU 33
Modules linked in: autofs4 target_core_iblock target_core_file target_core_pscsi target_core_mod configfs bnx2fc cnic uio fcoe libfcoe libfc scsi_transport_fc 8021q garp scsi_tgt stp llc cpufreq_ondemand freq_table pcc_cpufreq ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 power_meter microcode iTCO_wdt iTCO_vendor_support hpilo hpwdt sg bnx2x libcrc32c mdio serio_raw lpc_ich mfd_core shpchp ext4 jbd2 mbcache sd_mod crc_t10dif hpsa video output dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan]

Pid: 7355, comm: bnx2fc_thread/3 Not tainted 2.6.32-431.el6.x86_64 #1 HP ProLiant BL460c Gen8
RIP: 0010:[<ffffffffa03130da>]  [<ffffffffa03130da>] bnx2fc_init_task+0x6a/0x230 [bnx2fc]
RSP: 0018:ffff8820b0da3b68  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff882003801080 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff882003801100
RBP: ffff8820b0da3bc8 R08: ffffffff8160d4e8 R09: 0000000000000040
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88400e600e00
R13: ffff8840108fbe40 R14: ffff88200ffe5400 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff8820b0da0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 000000000000004c CR3: 0000002010b67000 CR4: 00000000001407e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process bnx2fc_thread/3 (pid: 7355, threadinfo ffff88401f940000, task ffff884012f5f540)
Stack:
 ffff8820b0da3bc8 ffffffff81527303 ffff884000000020 ffff8820b0da3bd8
<d> ffff8820b0da3b98 000000028138931a ffff88400f506078 ffff88400e600e00
<d> ffff88200ffe5400 ffff88200ffe5590 0000000000000021 0000000000000002
Call Trace:
 <IRQ>
 [<ffffffff81527303>] ? printk+0x41/0x46
 [<ffffffffa03169bc>] bnx2fc_post_io_req+0x11c/0x440 [bnx2fc]
 [<ffffffff812825b9>] ? cpumask_next_and+0x29/0x50
 [<ffffffff8137ffd0>] ? scsi_done+0x0/0x60
 [<ffffffffa0316df7>] bnx2fc_queuecommand+0x117/0x140 [bnx2fc]
 [<ffffffff81380245>] scsi_dispatch_cmd+0xe5/0x310
 [<ffffffff81388b9e>] scsi_request_fn+0x5ee/0x7a0
 [<ffffffff812658f1>] __blk_run_queue+0x31/0x40
 [<ffffffff81265a40>] blk_run_queue+0x30/0x50
 [<ffffffff81387da6>] scsi_run_queue+0xc6/0x270
 [<ffffffff81260f92>] ? elv_requeue_request+0x52/0xa0
 [<ffffffff813897a0>] scsi_requeue_command+0x90/0xb0
 [<ffffffff81389b84>] scsi_io_completion+0x154/0x6c0
 [<ffffffff8137ff62>] scsi_finish_command+0xc2/0x130
 [<ffffffff8138a255>] scsi_softirq_done+0x145/0x170
 [<ffffffff8126e865>] blk_done_softirq+0x85/0xa0
 [<ffffffff8107a8e1>] __do_softirq+0xc1/0x1e0
 [<ffffffff8100c30c>] ? call_softirq+0x1c/0x30
 [<ffffffff8100c30c>] call_softirq+0x1c/0x30
 <EOI>
 [<ffffffff8100fa75>] ? do_softirq+0x65/0xa0
 [<ffffffff8107a40a>] local_bh_enable_ip+0x9a/0xb0
 [<ffffffff8152a4eb>] _spin_unlock_bh+0x1b/0x20
 [<ffffffffa0313937>] bnx2fc_process_cq_compl+0x257/0x2b0 [bnx2fc]
 [<ffffffffa03114ea>] bnx2fc_percpu_io_thread+0xea/0x160 [bnx2fc]
 [<ffffffffa0311400>] ? bnx2fc_percpu_io_thread+0x0/0x160 [bnx2fc]
 [<ffffffff8109aef6>] kthread+0x96/0xa0
 [<ffffffff8100c20a>] child_rip+0xa/0x20
 [<ffffffff8109ae60>] ? kthread+0x0/0xa0
 [<ffffffff8100c200>] ? child_rip+0x0/0x20
Code: 89 df 45 8b 7e 30 0f 85 75 01 00 00 89 d1 31 c0 c1 e9 03 83 e2 04 89 c9 f3 48 ab 74 06 c7 07 00 00 00 00 49 89 9c 24 88 01 00 00 <83> 7e 4c 01 b8 01 00 00 00 0f 84 e7 00 00 00 89 c2 0a 53 38 41
RIP  [<ffffffffa03130da>] bnx2fc_init_task+0x6a/0x230 [bnx2fc]
 RSP <ffff8820b0da3b68>
CR2: 000000000000004c
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Function pci_enable_msix_range() may return negative values for error
conditions. So it's a bug by checking (pci_enable_msix_range() != 0)
for success and causes failure to megaraid driver when MSI is disabled.
[   16.487267] megaraid_sas 0000:02:00.0: Controller type: iMR
[   16.487275] genirq: Flags mismatch irq 0. 00000000 (megasas) vs. 00015a00 (tii
mer)
[   16.487347] megasas: Failed to register IRQ for vector 0.

Fixes: 8ae80ed1 "megaraid: Use pci_enable_msix_range() instead of pci_enable_msix()"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org> # 3.17

Connection retries were not being cleaned up correctly if they failed as a
result of link down. Applies on top of drivers-for-3.18.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>

This patch fixes an issue with multipath ipr SAS devices which require a
start unit command to be issued following an adapter reset. Without this
patch, paths get marked failed following an adapter reset and since the
error handler never gets invoked to issue the start unit, the paths are
never recovered. Returning FAILED for this case ensures the error
handler wakes up to issue the start unit.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>

Multipath devices using the TUR path checker need to see the sense
code for a failed TUR command in their device handler.  Since commit
14216561 we always return success for mid
layer issued TUR commands before calling the device handler, which
stopped the TUR path checker from working.

Move the call to the device handler check sense method before the early
return for TUR commands to give the device handler a chance to intercept
them.
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>

Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH.  Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state.  Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.

Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Meelis Roos <meelis.roos@ut.ee>
Tested-by: Meelis Roos <meelis.roos@ut.ee>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull arm64 fixes from Catalin Marinas:
 - enable bpf syscall for compat
 - cpu_suspend fix when checking the idle state type
 - defconfig update

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: defconfig: update defconfig for 3.18
  arm64: compat: Enable bpf syscall
  arm64: psci: fix cpu_suspend to check idle state type for index

Pull ARM SoC fixes from Olof Johansson:
 "Another quiet week:

   - a fix to silence edma probe error on non-supported platforms from
     Arnd
   - a fix to enable the PL clock for Parallella, to make mainline
     usable with the SDK.
   - a somewhat verbose fix for the PLL clock tree on VF610
   - enabling of SD/MMC on one of the VF610-based boards (for testing)
   - a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
     now needs to be added to the defconfig instead
   - another maintainer added for bcm2835: Lee Jones"

* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: zynq: Enable PL clocks for Parallella
  dma: edma: move device registration to platform code
  ARM: dts: vf610: add SD node to cosmic dts
  MAINTAINERS: update bcm2835 entry
  ARM: imx: Fix the removal of CONFIG_SPI option
  ARM: imx: clk-vf610: define PLL's clock tree

Pull devicetree bugfix from Grant Likely:
 "One buffer overflow bug that shouldn't be left around"

* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
  of: Fix overflow bug in string property parsing functions

Pull btrfs fix from Chris Mason:
 "It's a one liner for an error cleanup path that leads to crashes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup

Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are 3 tiny fixes for 3.18-rc4.

  One fixes up a long-stading race condition in the driver core for
  removing directories in /sys/devices/virtual/ and the other 2 fix up
  the wording of a new Kconfig option that was added in 3.18-rc1"

* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
  tiny: reverse logic for DISABLE_DEV_COREDUMP
  sysfs: driver core: Fix glue dir race condition by gdp_mutex

Pull staging driver fixes from Greg KH:
 "Here are some staging/iio fixes for 3.18-rc4.

  Nothing major, just a few bugfixes of things that have been reported"

* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging:iio:ade7758: Remove "raw" from channel name
  staging:iio:ade7758: Fix check if channels are enabled in prenable
  staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
  iio: as3935: allocate correct iio_device size
  io: accel: kxcjk-1013: Fix iio_event_spec direction
  iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
  iio: adc: mxs-lradc: Disable the clock on probe failure
  iio: st_sensors: Fix buffer copy
  staging:iio:ad5933: Drop "raw" from channel names
  staging:iio:ad5933: Fix NULL pointer deref when enabling buffer

Pull tty/serial fixes from Greg KH:
 "Here are some tiny serial/tty fixes for 3.18-rc4 that resolve some
  reported issues"

* tag 'tty-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: Fix pty master poll() after slave closes v2
  serial: of-serial: fix uninitialized kmalloc variable
  tty/vt: don't set font mappings on vc not supporting this
  tty: serial: 8250_mtk: Fix quot calculation
  tty: Prevent "read/write wait queue active!" log flooding
  tty: Fix high cpu load if tty is unreleaseable
  serial: Fix divide-by-zero fault in uart_get_divisor()

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 3.18-rc4.

  Just a bunch of little fixes resolving reported issues and new device
  ids for existing drivers.  Full details are in the shortlog"

* tag 'usb-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
  USB: Update default usb-storage delay_use value in kernel-parameters.txt
  USB: cdc-acm: add quirk for control-line state requests
  phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
  USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init()
  USB: cdc-acm: only raise DTR on transitions from B0
  Revert "storage: Replace magic number with define in usb_stor_euscsi_init()"
  usb: core: notify disconnection when core detects disconnect
  usb: core: need to call usb_phy_notify_connect after device setup
  uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models
  xhci: no switching back on non-ULT Haswell
  USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen
  USB: quirks: enable device-qualifier quirk for another Elan touchscreen
  MAINTAINERS: Remove duplicate entry for usbip driver
  usb: storage: fix build warnings !CONFIG_PM
  usb: Remove references to non-existent PLAT_S5P symbol
  uas: Add NO_ATA_1X for VIA VL711 devices
  xhci: Disable streams on Asmedia 1042 xhci controllers
  USB: HWA: fix a warning message
  uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model
  usb-storage: handle a skipped data phase
  ...

The Parallella board comes with a U-Boot bootloader that loads one of
two predefined FPGA bitstreams before booting the kernel. Both define an
AXI interface to the on-board Epiphany processor.

Enable clocks FCLK0..FCLK3 for the Programmable Logic by default.

Otherwise accessing, e.g., the ESYSRESET register freezes the board,
as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem.

Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull i2c bugfixes from Wolfram Sang:
 "One bigger cleanup (FSF address removal) and two bugfixes for I2C"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: Dispose OF IRQ mapping at client removal time
  i2c: at91: don't account as iowait
  i2c: remove FSF address

Pull irq fixes from Thomas Gleixner:
 "Two fixlets for the armada SoC interrupt controller"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: armada-370-xp: Fix MPIC interrupt handling
  irqchip: armada-370-xp: Fix MSI interrupt handling

Pull media fixes from Mauro Carvalho Chehab:
 "For:
   - some regression fixes at the Remote Controller core and imon driver
   - a build fix for certain randconfigs with ir-hix5hd2
   - don't feed power to satellite system at ds3000 driver init

  It also contains some fixes for drivers added for Kernel 3.18:
   - some fixes at the new ISDB-S driver, and the corresponding bits to
     fix some descriptors for this Japanese TV standard at the DVB core
   - two warning cleanups for sp2 driver if PM is disabled
   - change the default mode for the new vivid driver"

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] sp2: sp2_init() can be static
  [media] dvb:tc90522: fix always-false expression
  [media] dvb-core: set default properties of ISDB-S
  [media] dvb:tc90522: fix stats report
  [media] vivid: default to single planar device instances
  [media] imon: fix other RC type protocol support
  [media] ir-hix5hd2 fix build warning
  [media] ds3000: fix LNB supply voltage on Tevii S480 on initialization
  [media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding
  [media] rc-core: fix protocol_change regression in ir_raw_event_register