Putting the constant first is a supposed "best practice" that actually makes
the code harder to read.

Thanks to Roland Dreier for finding a bug in this "simple, obviously correct"
patch.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix hack that restricts the credit advertisement to 127.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RDS_LL_SEND_FULL bit should be set when we stop transmitted due to
flow control.  Otherwise the send worker will keep trying as opposed to
sleeping until we unthrottle.  Saves CPU.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Had some lingering instances of _iw_ variable names from when
the listen code was centralized into rdma_transport.c
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the recv ring low water mark is 1/4 the depth.  Performance
measurements show that this limits iWARP throughput by flow controlling
the rds-stress senders.  Setting it to 1/2 seems to max the T3
performance.  I tried even higher levels but that didn't help and it
started to increase the rds thread cpu utilization.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the merging of mISDN, state which files refer only to the
old isdn4linux subsystem. Also add a few missing files and sort
alphabetically.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Neither the lm90 driver nor the lm87 driver do support interrupts, so
there is no point in specifying one when declaring the devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Aligning register offset translation table imporves performance
on rx side.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable multiple rx rings for older NX2031 chip, firmware 3.4.336
or newer supports this feature.
Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace superfluous wrapper functions with two macros:

NXWR32 replaces netxen_nic_reg_write, netxen_nic_write_w0,
netxen_nic_read_w1, netxen_crb_writelit_adapter.

NXRD32 replaces netxen_nic_reg_read, netxen_nic_read_w0,
netxen_nic_read_w1.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o remove unnecessary length parameter since register access
  width is fixed 4 byte.
o remove superfluous pci_read_normalize and pci_write_normalize
  functions.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reduces netxen_adapter footprint when rss (msi-x) is disabled.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for asynchronous events from firmware,
received over one of the rx rings.

Add support for event based phy interrupts, enhanced links
status reporting from firmware.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed duplicate firmware handshake, defer it until first
port (interface) is brought up.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o move tx stuff into nx_host_tx_ring structure, this will
  help managing multiple tx rings in future.
o sanitize some variable names
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rearrange members to align them at right offset.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o remove unused structure defs.
o remove unnecessary includes.
o replace enums with specific #defines.
o reduce footprint of stats structure.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'core/softlockup' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: make DETECT_HUNG_TASK default depend on DETECT_SOFTLOCKUP
  softlockup: move 'one' to the softlockup section in sysctl.c
  softlockup: ensure the task has been switched out once
  softlockup: remove timestamp checking from hung_task
  softlockup: convert read_lock in hung_task to rcu_read_lock
  softlockup: check all tasks in hung_task
  softlockup: remove unused definition for spawn_softlockup_task
  softlockup: fix potential race in hung_task when resetting timeout
  softlockup: fix to allow compiling with !DETECT_HUNG_TASK
  softlockup: decouple hung tasks check from softlockup detection

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
  branch tracer: Fix for enabling branch profiling makes sparse unusable
  ftrace: Correct a text align for event format output
  Update /debug/tracing/README
  tracing/ftrace: alloc the started cpumask for the trace file
  tracing, x86: remove duplicated #include
  ftrace: Add check of sched_stopped for probe_sched_wakeup
  function-graph: add proper initialization for init task
  tracing/ftrace: fix missing include string.h
  tracing: fix incorrect return type of ns2usecs()
  tracing: remove CALLER_ADDR2 from wakeup tracer
  blktrace: fix pdu_len when tracing packet command requests
  blktrace: small cleanup in blk_msg_write()
  blktrace: NUL-terminate user space messages
  tracing: move scripts/trace/power.pl to scripts/tracing/power.pl

* 'irq/threaded' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: fix devres.o build for GENERIC_HARDIRQS=n
  genirq: provide old request_irq() for CONFIG_GENERIC_HARDIRQ=n
  genirq: threaded irq handlers review fixups
  genirq: add support for threaded interrupts to devres
  genirq: add threaded interrupt handler support

Commit c2ec175c ("mm: page_mkwrite
change prototype to match fault") exposed a bug in the NFS
implementation of page_mkwrite.  We should be returning 0 on success...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI: pci_slot: grab refcount on slot's bus
  PCI Hotplug: acpiphp: grab refcount on p2p subordinate bus
  PCI: allow PCI core hotplug to remove PCI root bus
  PCI: Fix oops in pci_vpd_truncate
  PCI: don't corrupt enable_cnt when doing manual resource alignment
  PCI: annotate pci_rescan_bus as __ref, not __devinit
  PCI-IOV: fix missing kernel-doc
  PCI: Setup disabled bridges even if buses are added
  PCI: SR-IOV quirk for Intel 82576 NIC

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  loop: mutex already unlocked in loop_clr_fd()
  cfq-iosched: don't let idling interfere with plugging
  block: remove unused REQ_UNPLUG
  cfq-iosched: kill two unused cfqq flags
  cfq-iosched: change dispatch logic to deal with single requests at the time
  mflash: initial support
  cciss: change to discover first memory BAR
  cciss: kernel scan thread for MSA2012
  cciss: fix residual count for block pc requests
  block: fix inconsistency in I/O stat accounting code
  block: elevator quiescing helpers

The code that enables branch tracing for all (non-constant) branches
plays games with the preprocessor and #define's the C 'if ()' construct
to do tracing.

That's all fine, but it fails for some unusual but valid C code that is
sometimes used in macros, notably by the intel-iommu code:

	if (i=drhd->iommu, drhd->ignored) ..

because now the preprocessor complains about multiple arguments to the
'if' macro.

So make the macro expansion of this particularly horrid trick use
varargs, and handle the case of comma-expressions in if-statements.  Use
another macro to do it cleanly in just one place.

This replaces a patch by David (and acked by Steven) that did this all
inside that one already-too-horrid macro.
Tested-by: Ingo Molnar <mingo@elte.hu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6:
  ASoC: TWL4030: Compillation error fix

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (36 commits)
  ALSA: hda - Add VREF powerdown sequence for another board
  ALSA: oss - volume control for CSWITCH and CROUTE
  ALSA: hda - add missing comma in ad1884_slave_vols
  sound: usb-audio: allow period sizes less than 1 ms
  sound: usb-audio: save data packet interval in audioformat structure
  sound: usb-audio: remove check_hw_params_convention()
  sound: usb-audio: show sample format width in proc file
  ASoC: fsl_dma: Pass the proper device for dma mapping routines
  ASoC: Fix null dereference in ak4535_remove()
  ALSA: hda - enable SPDIF output for Intel DX58SO board
  ALSA: snd-atmel-abdac: increase periods_min to 6 instead of 4
  ALSA: snd-atmel-abdac: replace bus_id with dev_name()
  ALSA: snd-atmel-ac97c: replace bus_id with dev_name()
  ALSA: snd-atmel-ac97c: cleanup registers when removing driver
  ALSA: snd-atmel-ac97c: do a proper reset of the external codec
  ALSA: snd-atmel-ac97c: enable interrupts to catch events for error reporting
  ALSA: snd-atmel-ac97c: set correct size for buffer hardware parameter
  ALSA: snd-atmel-ac97c: do not overwrite OCA and ICA when assigning channels
  ALSA: snd-atmel-ac97c: remove dead break statements after return in switch case
  ALSA: snd-atmel-ac97c: cleanup register definitions
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  sata_mv: shorten register names
  sata_mv: workaround errata SATA#13
  sata_mv: cosmetic renames
  sata_mv: workaround errata SATA#26
  sata_mv: workaround errata PCI#7
  sata_mv: replace 0x1f with ATA_PIO4 (v2)
  sata_mv: fix irq mask races
  sata_mv: revert SoC irq breakage
  libata: ahci enclosure management bios workaround
  ata: Add TRIM infrastructure
  ata_piix: VGN-BX297XP wants the controller power up on suspend
  libata: Remove some redundant casts from pata_octeon_cf.c
  pata_artop: typo

* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
  i2c: imx: Make disable_delay a per-device variable
  i2c: xtensa s6000 i2c driver
  powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
  i2c: i2c-mpc: make I2C bus speed configurable
  i2c: i2c-mpc: use dev based printout function
  i2c: i2c-mpc: various coding style fixes
  i2c: imx: Add missing request_mem_region in probe()
  i2c: i2c-s3c2410: Initialise Samsung I2C controller early
  i2c-s3c2410: Simplify bus frequency calculation
  i2c-s3c2410: sda_delay should be in ns, not clock ticks
  i2c: iMX/MXC support

* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  hwmon: Add Asus ATK0110 support
  hwmon: (lm95241) Convert to new-style i2c driver

PCI parallel port devices can IRQ share so we should stop them hogging
the line and making a mess on modern PC systems.  We know the sharing
side works as the PCMCIA driver has shared the parallel port IRQ for
some time.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Here are some cleanups, mainly removing unused variables and silly
declarations.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Depend on KGDB_SERIAL_CONSOLE being set to N rather than !Y, since it can
be built as a module.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Both software emulated and hardware based CTS and RTS are enabled in
serial driver.

The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device.  In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

(akpm: queued pending confirmation of the new major number)

[randy.dunlap@oracle.com: select SERIAL_CORE]
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This is a low density serial port so needs a real major/minor
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>