Support matching on ICMP type and code.

Example usage:

tc qdisc add dev eth0 ingress

tc filter add dev eth0 protocol ip parent ffff: flower \
	indev eth0 ip_proto icmp type 8 code 0 action drop

tc filter add dev eth0 protocol ipv6 parent ffff: flower \
	indev eth0 ip_proto icmpv6 type 128 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow dissection of ICMP(V6) type and code. This should only occur
if a packet is ICMP(V6) and the dissector has FLOW_DISSECTOR_KEY_ICMP set.

There are currently no users of FLOW_DISSECTOR_KEY_ICMP.
A follow-up patch will allow FLOW_DISSECTOR_KEY_ICMP to be used by
the flower classifier.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
	For backwards compatibility: "st,spear600-gmac" is also supported.

Previously, when specifying "snps,dwmac-4.10a", "snps,dwmac" as your
compatible string, plat_stmmacenet_data would have both has_gmac and
has_gmac4 set.

This would lead to stmmac_hw_init calling dwmac1000_setup rather than
dwmac4_setup, resulting in a non-functional driver.
This happened since the check for has_gmac is done before the check for
has_gmac4. However, the order should not matter, so it does not make sense
to have both set.

If something is valid for both, you should do as the stmmac_interrupt does:
if (priv->plat->has_gmac || priv->plat->has_gmac4) ...

The places where it was obvious that the author actually meant
if (has_gmac || has_gmac4) rather than if (has_gmac) has been updated.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devicetree binding for stmmac states:
- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac"
	For backwards compatibility: "st,spear600-gmac" is also supported.

Since dwmac-generic.c calls stmmac_probe_config_dt explicitly,
another alternative would have been to remove all compatible strings
other than "snps,dwmac" and "st,spear600-gmac" from dwmac-generic.c.

However, that would probably do more good than harm, since when trying
to figure out what hardware a certain driver supports, you usually look
at the compatible strings in the struct of_device_id, and not in some
function defined in a completely different file.

No functional change intended.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

snps,tso was previously placed under AXI BUS Mode parameters,
suggesting that the property should be in the stmmac-axi-config node.

TSO (TCP Segmentation Offloading) has nothing to do with AXI BUS Mode
parameters, and the parser actually expects it to be in the root node,
not in the stmmac-axi-config.

Also added a note about snps,tso only being available on GMAC4 and newer.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.

Also avoid casting away the const qualifier of the return value by
making temac_init_mac_address() take a const void* address.

Follows commit b34296a9 ("net: ethoc: Utilize
of_get_mac_address()").

Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.

Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.

Follows commit b34296a9 ("net: ethoc: Utilize
of_get_mac_address()").

Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
net/sched: cls_flower: Add support for matching on dissection flags

This series add the UAPI to provide set of flags for matching, where the
flags provided from user-space are mapped to flow-dissector flags.

The 1st flag allows to match on whether the packet is an
IP fragment and corresponds to the FLOW_DIS_IS_FRAGMENT flag.

v2->v3:
  - replace BIT() with << (kbuild test robot)

v1->v2:
 - dropped the flow dissector patch (#1) as no changes are needed there (Jiri)
 - applied code review comments from Jiri to the flower patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable offloading of matching on packets being fragments.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add UAPI to provide set of flags for matching, where the flags
provided from user-space are mapped to flow-dissector flags.

The 1st flag allows to match on whether the packet is an
IP fragment and corresponds to the FLOW_DIS_IS_FRAGMENT flag.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These two statements were not indented correctly so it's sort of
confusing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We never set "slots" in this function.

Fixes: a9380b0f ("drivers: net: xgene: Add support for Jumbo frame")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

test_and_set_bit() already implies a memory barrier.
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Peng Tao <bergwolf@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, icmp_rcv() always return zero on a packet delivery upcall.

To make its behavior more compliant with the way this API should be
used, this patch changes this to let it return NET_RX_SUCCESS when the
packet is proper handled, and NET_RX_DROP otherwise.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS updates for net-next

The following patchset contains a large Netfilter update for net-next,
to summarise:

1) Add support for stateful objects. This series provides a nf_tables
   native alternative to the extended accounting infrastructure for
   nf_tables. Two initial stateful objects are supported: counters and
   quotas. Objects are identified by a user-defined name, you can fetch
   and reset them anytime. You can also use a maps to allow fast lookups
   using any arbitrary key combination. More info at:

   http://marc.info/?l=netfilter-devel&m=148029128323837&w=2

2) On-demand registration of nf_conntrack and defrag hooks per netns.
   Register nf_conntrack hooks if we have a stateful ruleset, ie.
   state-based filtering or NAT. The new nf_conntrack_default_on sysctl
   enables this from newly created netnamespaces. Default behaviour is not
   modified. Patches from Florian Westphal.

3) Allocate 4k chunks and then use these for x_tables counter allocation
   requests, this improves ruleset load time and also datapath ruleset
   evaluation, patches from Florian Westphal.

4) Add support for ebpf to the existing x_tables bpf extension.
   From Willem de Bruijn.

5) Update layer 4 checksum if any of the pseudoheader fields is updated.
   This provides a limited form of 1:1 stateless NAT that make sense in
   specific scenario, eg. load balancing.

6) Add support to flush sets in nf_tables. This series comes with a new
   set->ops->deactivate_one() indirection given that we have to walk
   over the list of set elements, then deactivate them one by one.
   The existing set->ops->deactivate() performs an element lookup that
   we don't need.

7) Two patches to avoid cloning packets, thus speed up packet forwarding
   via nft_fwd from ingress. From Florian Westphal.

8) Two IPVS patches via Simon Horman: Decrement ttl in all modes to
   prevent infinite loops, patch from Dwip Banerjee. And one minor
   refactoring from Gao feng.

9) Revisit recent log support for nf_tables netdev families: One patch
   to ensure that we correctly handle non-ethernet packets. Another
   patch to add missing logger definition for netdev. Patches from
   Liping Zhang.

10) Three patches for nft_fib, one to address insufficient register
    initialization and another to solve incorrect (although harmless)
    byteswap operation. Moreover update xt_rpfilter and nft_fib to match
    lbcast packets with zeronet as source, eg. DHCP Discover packets
    (0.0.0.0 -> 255.255.255.255). Also from Liping Zhang.

11) Built-in DCCP, SCTP and UDPlite conntrack and NAT support, from
    Davide Caratti. While DCCP is rather hopeless lately, and UDPlite has
    been broken in many-cast mode for some little time, let's give them a
    chance by placing them at the same level as other existing protocols.
    Thus, users don't explicitly have to modprobe support for this and
    NAT rules work for them. Some people point to the lack of support in
    SOHO Linux-based routers that make deployment of new protocols harder.
    I guess other middleboxes outthere on the Internet are also to blame.
    Anyway, let's see if this has any impact in the midrun.

12) Skip software SCTP software checksum calculation if the NIC comes
    with SCTP checksum offload support. From Davide Caratti.

13) Initial core factoring to prepare conversion to hook array. Three
    patches from Aaron Conole.

14) Gao Feng made a wrong conversion to switch in the xt_multiport
    extension in a patch coming in the previous batch. Fix it in this
    batch.

15) Get vmalloc call in sync with kmalloc flags to avoid a warning
    and likely OOM killer intervention from x_tables. From Marcelo
    Ricardo Leitner.

16) Update Arturo Borrero's email address in all source code headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-12-07

This series contains updates to i40e and i40evf only.

Filip modifies the i40e to log link speed change and when the link is
brought up and down.

Mitch replaces i40e_txd_use_count() with a new function which is slightly
faster and better documented so the dim witted can better follow the
code.  Fixes the locking of the service task so that it is actually
done in the service task and not in the scheduling function which calls
the service task.

Jacob, being the busy little beaver he is, provides most of the changes
starting restores a workaround that is still needed in some configurations,
specifically the Ethernet Controller XL710 for 40GbE QSFP+.  Removes
duplicate code and simplifies the i40e_vsi_add_vlan() and
i40e_vsi_kill_vlan() functions.  Removes detection of PTP frames over L4
(UDP) on the XL710 MAC, since there was a product decision to defeature
it.  Fixed a previous refactor of active filters which caused issues in
the accounting of active_filters.  Remaining work was done in the VLAN
filters to improve readability and simplify code as much as possible
to reduce inconsistencies.

Alex fixes foul budget accounting in core code by returning actual
work done, capped to budget-1.

Henry fixes the "ethtool -p" function for 1G BaseT PHYs.

Carolyn adds support for 25G devices for i40e and i40evf.

Michal adds functions to apply the correct access method for external PHYs
which could use Clause22 or Clause45 depending on the PHY.

v2: dropped last patch from previous series, since changes are needed based
    on feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 61e84623 ("net: centralize net_device min/max MTU checking"),
the mtu range for dummy device becomes [68, 1500].

This patch extends it to [0, 65535].
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 61e84623 ("net: centralize net_device min/max MTU checking"),
mtu range is checked at dev_set_mtu().

This patch adds min_mtu for nlmon device and remove unnecessary
ndo_change_mtu() function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When free macvlan_port in macvlan_port_destroy, it is safe to free
directly because netdev_rx_handler_unregister could enforce one
grace period.
So it is unnecessary to use kfree_rcu for macvlan_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two functions which would free the ipvl_port now. The first
is ipvlan_port_create. It frees the ipvl_port in the error handler,
so it could kfree it directly. The second is ipvlan_port_destroy. It
invokes netdev_rx_handler_unregister which enforces one grace period
by synchronize_net firstly, so it also could kfree the ipvl_port
directly and safely.

So it is unnecessary to use kfree_rcu to free ipvl_port.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

General assumption is that single program can hold up to BPF_MAXINSNS,
that is, 4096 number of instructions. It is the case with cBPF and
that limit was carried over to eBPF. When recently testing digest, I
noticed that it's actually not possible to feed 4096 instructions
via bpf(2).

The check for > BPF_MAXINSNS was added back then to bpf_check() in
cbd35700 ("bpf: verifier (add ability to receive verification log)").
However, 09756af4 ("bpf: expand BPF syscall with program load/unload")
added yet another check that comes before that into bpf_prog_load(),
but this time bails out already in case of >= BPF_MAXINSNS.

Fix it up and perform the check early in bpf_prog_load(), so we can drop
the second one in bpf_check(). It makes sense, because also a 0 insn
program is useless and we don't want to waste any resources doing work
up to bpf_check() point. The existing bpf(2) man page documents E2BIG
as the official error for such cases, so just stick with it as well.

Fixes: 09756af4 ("bpf: expand BPF syscall with program load/unload")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

>From what I can tell, spin_lock(&priv->lock) is not needed, since the
phy_ethtool_ksettings_set call is not given the priv struct.

phy_start_aneg takes the phydev->lock. Calls to phy_adjust_link
from phy_state_machine also takes the phydev->lock.

[   13.718319] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:97
[   13.726717] in_atomic(): 1, irqs_disabled(): 0, pid: 1307, name: ethtool
[   13.742115] Hardware name: Axis ARTPEC-6 Platform
[   13.746829] [<80110568>] (unwind_backtrace) from [<8010c2bc>] (show_stack+0x18/0x1c)
[   13.754575] [<8010c2bc>] (show_stack) from [<80433484>] (dump_stack+0x80/0xa0)
[   13.761801] [<80433484>] (dump_stack) from [<80145428>] (___might_sleep+0x108/0x170)
[   13.769554] [<80145428>] (___might_sleep) from [<806c9b50>] (mutex_lock+0x24/0x44)
[   13.777128] [<806c9b50>] (mutex_lock) from [<8050cbc0>] (phy_start_aneg+0x1c/0x13c)
[   13.784783] [<8050cbc0>] (phy_start_aneg) from [<8050d338>] (phy_ethtool_ksettings_set+0x98/0xd0)
[   13.793656] [<8050d338>] (phy_ethtool_ksettings_set) from [<80517adc>] (stmmac_ethtool_set_link_ksettings+0xa0/0xb4)
[   13.804184] [<80517adc>] (stmmac_ethtool_set_link_ksettings) from [<805c5138>] (ethtool_set_settings+0xd4/0x13c)
[   13.814358] [<805c5138>] (ethtool_set_settings) from [<805c9718>] (dev_ethtool+0x13c4/0x211c)
[   13.822882] [<805c9718>] (dev_ethtool) from [<805dc7c0>] (dev_ioctl+0x480/0x8e0)
[   13.830291] [<805dc7c0>] (dev_ioctl) from [<80260e34>] (do_vfs_ioctl+0x94/0xa00)
[   13.837699] [<80260e34>] (do_vfs_ioctl) from [<802617dc>] (SyS_ioctl+0x3c/0x60)
[   13.845011] [<802617dc>] (SyS_ioctl) from [<801088bc>] (__sys_trace_return+0x0/0x10)
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Grygorii Strashko says:

====================
net: ethernet: ti: cpts: update and fixes

It is preparation series intended to clean up and optimize TI CPTS driver to
facilitate further integration with other TI's SoCs like Keystone 2.

Changes in v5:
- fixed copy paste error in cpts_release
- reworked cc.mult/shift and cc_mult initialization

Changes in v4:
- fixed build error in patch
  "net: ethernet: ti: cpts: clean up event list if event pool is empty"
- rebased on top of net-next

Changes in v3:
- patches reordered: fixes and small updates moved first
- added comments in code about cpts->cc_mult
- conversation range (maxsec) limited to 10sec

Changes in v2:
- patch "net: ethernet: ti: cpts: rework initialization/deinitialization"
  was split on 4 patches
- applied comments from Richard Cochran
- dropped patch
  "net: ethernet: ti: cpts: add return value to tx and rx timestamp funcitons"
- new patches added:
  "net: ethernet: ti: cpts: drop excessive writes to CTRL and INT_EN regs"
  and "clocksource: export the clocks_calc_mult_shift to use by timestamp code"

Links on prev versions:
v4: https://lkml.org/lkml/2016/12/6/496
v3: https://www.spinics.net/lists/devicetree/msg153474.html
v2: http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg1282034.html
v1: http://www.spinics.net/lists/linux-omap/msg131925.html
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.

Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
 max_sec_before_overflow = max_counter_val / rftclk_freq.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.

Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.

Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CPSW CPTS driver is capable of doing timestamping on tx/rx packets and
requires to know mult and shift factors for timestamp conversion from raw
value to nanoseconds (ptp clock). Now these mult and shift factors are
calculated manually and provided through DT, which makes very hard to
support of a lot number of platforms, especially if CPTS refclk is not the
same for some kind of boards and depends on efuse settings (Keystone 2
platforms). Hence, export clocks_calc_mult_shift() to allow drivers like
CPSW CPTS (and other ptp drivesr) to benefit from automaitc calculation of
mult and shift factors.

Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.

This patch splits CPTS initialization and deinitialization on two parts:

- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;

- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.

As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries.  When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().

So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two issues with TI CPTS code which are reproducible when TI
CPSW ethX device passes few up/down iterations:
- cpts refclk prepare counter continuously incremented after each
up/down iteration;
- devm_clk_get(dev, "cpts") is called many times.

Hence, fix these issues by using clk_disable_unprepare() in
cpts_clk_release() and skipping devm_clk_get() if cpts refclk has been
acquired already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.

Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch to readl/writel_relaxed() APIs, because this is recommended
API and the CPTS IP is reused on Keystone 2 SoCs
where LE/BE modes are supported.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Add interface to support RDMA driver.

This series adds an interface to support a brand new RDMA driver bnxt_re.
The first step is to re-arrange some code so that pci_enable_msix() can
be called during pci probe.  The purpose is to allow the RDMA driver to
initialize and stay initialized whether the netdev is up or down.

Then we make some changes to VF resource allocation so that there is
enough resources to support RDMA.

Finally the last patch adds a simple interface to allow the RDMA driver to
probe and register itself with any bnxt_en devices that support RDMA.
Once registered, the RDMA driver can request MSIX, send fw messages, and
receive some notifications.

v2: Fixed kbuild test robot warnings.

David, please consider this series for net-next.  Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the network driver and RDMA driver operate on the same PCI function,
we need to create an interface to allow the RDMA driver to share resources
with the network driver.

1. Create a new bnxt_en_dev struct which will be returned by
bnxt_ulp_probe() upon success.  After that, all calls from the RDMA driver
to bnxt_en will pass a pointer to this struct.

2. This struct contains additional function pointers to register, request
msix, send fw messages, register for async events.

3. If the RDMA driver wants to enable RDMA on the function, it needs to
call the function pointer bnxt_register_device().  A ulp_ops structure
is passed for RCU protected upcalls from bnxt_en to the RDMA driver.

4. The RDMA driver can call firmware APIs using the bnxt_send_fw_msg()
function pointer.

5. 1 stats context is reserved when the RDMA driver registers.  MSIX
and completion rings are reserved when the RDMA driver calls
bnxt_request_msix() function pointer.

6. When the RDMA driver calls bnxt_unregister_device(), all RDMA resources
will be cleaned up.

v2: Fixed 2 uninitialized variable warnings.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver register function with firmware consists of passing version
information and registering for async events.  To support the RDMA driver,
the async events that we need to register may change.  Separate the
driver register function into 2 parts so that we can just update the
async events for the RDMA driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>