Driver uses four different fields for internal flags. They can be merged
into one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The driver often sets only particular bits of configuration registers.
Using separate function to such action simplifies the code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

All timing registers should contain values decreased by one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

PCLK clock is used by DECON IP. The patch also replaces magic number with
number of clocks in array definition.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Struct of gem object in exynos_drm driver is struct exynos_drm_gem_obj.
It's too long and we can know its meaning of name without _obj postfix.

We use several names to variable name of gem object for exynos_drm -
exynos_gem_obj, gem_obj and obj. Especially "obj" name can cause
misunderstanding with variable name "obj" of struct drm_gem_object.

This will clean about name of gem object for exynos_drm as follows.
s/struct exynos_drm_gem_obj/struct exynos_drm_gem
s/exynos_gem_obj or gem_obj or obj/exynos_gem
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The arm_iommu_detach_device() is a function to detach device of iommu
attached by arm_iommu_attach_device(). The exynos-drm uses
arm_iommu_attach_device() so it should use arm_iommu_detach_device() to
detach device of iommu, not iommu_detach_device().

The drm_release_iommu_mapping() is a function to release mapping of
iommu created by arm_iommu_create_mapping(). It is called by
exynos_drm_unload() so shouldn't be called by drm_iommu_detach_device().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Set one of the planes for each crtc driver as a cursor plane enabled
window managers to fully work on exynos.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Define DEFAULT_WIN as zero to help set the primary plane on all CRTCs.
Some CRTCs were defining a variable to store the default window, but that
is not necessary as the default (primary) window is always the window zero.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch fixes spelling errors in drm fimc/gsc
inavild -> invaild
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch fixes calling usleep_range() after taking reg_slock
using spin_lock_irqsave(). The mdelay() is used instead.
Waiting in atomic context is not the best idea in general.
Hopefully, waiting occurs only when Video Processor fails
to reset correctly.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch removes unused hdmi_context field.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Simple formula can be used to calculate CTS and N coefficients.
Additionaly ACR registers have different offsets for different versions
of IP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Inline function is safer than macro, also the name has been changed to
be consistent with other inline function encoder_to_hdmi.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

hdmi_resources structure was filled by old platform data code and is not
necessary anymore. The patch removes it at groups together resource related
fields in hdmi_context.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch converts API to gpiod and moves initialization code
to hdmi_resources_init.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Driver tries to disable sclk_hdmi during re-parenting, to avoid possible
glitches. It is ineffective as the clock is used also by other devices (mixer).
Anyway driver works without disabling sclk_hdmi.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Driver always uses the same number of regulators, so there is no point in
dynamic allocation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

hdmi-en is an optional regulator so it should be better handled by
devm_regulator_get_optional call.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

DRM device should be destroyed before releasing resources.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Registers are 32-bit, even if only lower 8-bits are used.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Currently driver tries to set specific HDMI-PHY registers in three situations:
- before reset,
- before power off,
- after applying HDMI-PHY configuration.

First two cases seems to be unnecessary - register contents will be lost
anyway. The third case can be merged with HDMI-PHY configuration by fixing
the last byte of configuration data.

The patch has been tested with following platforms:
- exynos4210-universal_c210,
- exynos4412-odroidu3,
- exynos5422-odroidxu3.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch moves PLL stabilization check to separate function, adjust timeout
parameters and de-duplicates code common for both HW variants.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Some registers resides at different offsets depending on device version.
This patch adds infrastructure for mapping such registers to proper address
based on hdmi_type. It adds also mappings to some registers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This compatible was marked as deprecated in Jun 2013 and it is not used since
then. Additionally its driver data points to wrong pll settings, so it
cannot work anyway.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

A bit smaller pull this time.  Few minor things, plus initial support
for msm8996 (snapdragon 820)..  Sorry, a bit latish, was hoping to get
some 8960/8064 DSI stuff included.  But still waiting on the v2 of the
patchset (just pending some minor review comments).  It would be nice
to get the DSI patches merged since it would help some folks trying to
get upstream kernel running on n4/n7 and xperia z and wanting to write
some more panel drivers.  Also, waiting for OCMEM driver to get merged
via other trees and then I have a small bit to go along with that to
make the gpu actually work on devices w/ OCMEM (snapdragon 800, 805,
etc).  So maybe a second later pull req, time permitting.

* 'msm-next' of git://people.freedesktop.org/~robclark/linux:
  drm/msm: Remove local fbdev emulation Kconfig option
  drm/msm/mdp5: Basic support for MDP5 v1.7 (MSM8996)
  drm/msm/mdp: Add Software Pixel Extension support
  drm/msm/mdp5: Use the newly introduced enum mdp_component_type
  drm/msm/hdmi: Add basic HDMI support for msm8996
  drm/msm/mdp5: Avoid printing error messages for optional clocks
  drm/msm: Fix IOMMU clean up path in case msm_iommu_new() fails
  drm/msm/mdp5: remove the cfg pointer from SMP struct
  drm/msm/dsi: Updata LNn_CFG4 register settings for 28nm PHY
  drm: msm: dsi: Don't attempt changing voltage of switches
  drm/msm: update generated headers

DRM_MSM_FBDEV config is used to enable/disable fbdev emulation for the
msm kms driver.

Replace this with the top level DRM_FBDEV_EMULATION config option where
applicable. This also prevents build breaks caused by undefined
drm_fb_helper_* functions when legacy fbdev support was disabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

This change adds the basic MDP5 support for MSM8996.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

In order to produce an image, the scalar needs to be fed extra
pixels. These top/bottom/left/right values depend on a various of
factors, including resolution, scaling type, phase step and
initial phase.

Pixel Extension are programmed by hardware in most targets - and
can be overwritten by software. For some targets (e.g.: msm8996),
software *must* program those registers.

In order to ease this computation, let's always use bilinear
filters, which are easier to program from kernel. Eventually,
all of these values will come down from user space for better
quality.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

When calculating phase steps, let's use the same enum
mdp_component_type in order to ease the readability; 0/1 indexes
are a bit confusing and we now have explicit values to index
this type of arrays.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The HDMI controller is new in MDP5 v1.7. As of now, this change
doesn't reflect the novelty and only adds the basics so the probe
gets triggered.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The current behavior is to try to get optional clocks and print a
dev_err message in case of failure. This looks rather confusing
and may increase with the amount of optional clocks.

We may need a cleaner way to handle per-device clocks but in the
meantime, let's reduce the amount of dev_err messages during the
probe.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

msm_iommu_new() can fail and this change makes sure that we
detect the failure and free the allocated domain before going
any further.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

We want to make sure we control all the information being passed
down to SMP block. Having access to the cfg pointer here may create
bad things in the future.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

The current settings for 28nm PHY data lane CFG4 registers do
not work with certain panels. This change is to modify them to
hw recommended values.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

In some configurations the supplies are voltage switches and not LDOs,
making the set voltage call to fail. Check with the regulator framework
if the supply can change voltage before attempting.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>

Signed-off-by: Rob Clark <robdclark@gmail.com>

rcar-du support for r8a7793/4
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
  drm: rcar-du: Add support for the R8A7794 DU
  drm: rcar-du: Add support for the R8A7793 DU

This pull request introduces the vc4 driver, for kernel modesetting on
the Raspberry Pi (bcm2835/bcm2836 architectures).  It currently
supports a display plane and cursor on the HDMI output.  The driver
doesn't do 3D, power management, or overlay planes yet.

[airlied: fixup the enable/disable vblank APIs]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>

* tag 'drm-vc4-next-2015-10-21' of http://github.com/anholt/linux:
  drm/vc4: Allow vblank to be disabled
  drm/vc4: Use the fbdev_cma helpers
  drm/vc4: Add KMS support for Raspberry Pi.
  drm/vc4: Add devicetree bindings for VC4.

The R8A7794 DU has a fixed output routing configuration with one RGB
output per CRTC and thus lacks the RGB output routing register field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

The R8A7793 DU is identical to the R8A7791 and thus only requires a new
DT compatible string.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>