[ Upstream commit cee26487 ]

In flow steering, if asked to, the hardware matches on the first ethertype
which is not vlan. It's possible to set a rule as follows, which is meant
to match on untagged packet, but will match on a vlan packet:
    tc filter add dev eth0 parent ffff: protocol ip flower ...

To avoid this for packets with single tag, we set vlan masks to tell
hardware to check the tags for every matched packet.

Fixes: 095b6cfd ('net/mlx5e: Add TC vlan match parsing')
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bf3b452b ]

The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.

Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.

Fixes: d9338023 ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9d2f67e4 ]

When we use raw socket as the vhost backend, a packet from virito with
gso offloading information, cannot be sent out in later validaton at
xmit path, as we did not set correct skb->protocol which is further used
for looking up the gso function.

To fix this, we set this field according to virito hdr information.

Fixes: e858fae2 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Jianfeng Tan <jianfeng.tan@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 0431100b ]

Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.

According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.

This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: f748be53 ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7e823644 ]

Commit 2276f58a ("udp: use a separate rx queue for packet reception")
turned static inline __skb_recv_udp() from being a trivial helper around
__skb_recv_datagram() into a UDP specific implementaion, making it
EXPORT_SYMBOL_GPL() at the same time.

There are external modules that got broken by __skb_recv_udp() not being
visible to them. Let's unbreak them by making __skb_recv_udp EXPORT_SYMBOL().

Rationale (one of those) why this is actually "technically correct" thing
to do: __skb_recv_udp() used to be an inline wrapper around
__skb_recv_datagram(), which itself (still, and correctly so, I believe)
is EXPORT_SYMBOL().

Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 2276f58a ("udp: use a separate rx queue for packet reception")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 92ef12b3 ]

In the case of implicit connect message with data > 1K, the flow
control accounting is incorrect. At this state, the socket does not
know the peer nodes capability and falls back to legacy flow control
by return 1, however the receiver of this message will perform the
new block accounting. This leads to a slack and eventually traffic
disturbance.

In this commit, we perform tipc_node_get_capabilities() at implicit
connect and perform accounting based on the peer's capability.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 471b83bd ]

team's ndo_add_slave() acquires 'team->lock' and later tries to open the
newly enslaved device via dev_open(). This emits a 'NETDEV_UP' event
that causes the VLAN driver to add VLAN 0 on the team device. team's
ndo_vlan_rx_add_vid() will also try to acquire 'team->lock' and
deadlock.

Fix this by checking early at the enslavement function that a team
device is not being enslaved to itself.

A similar check was added to the bond driver in commit 09a89c21
("bonding: disallow enslaving a bond to itself").

WARNING: possible recursive locking detected
4.18.0-rc7+ #176 Not tainted
--------------------------------------------
syz-executor4/6391 is trying to acquire lock:
(____ptrval____) (&team->lock){+.+.}, at: team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868

but task is already holding lock:
(____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&team->lock);
  lock(&team->lock);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

2 locks held by syz-executor4/6391:
 #0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
 #0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4662
 #1: (____ptrval____) (&team->lock){+.+.}, at: team_add_slave+0xdb/0x1c30 drivers/net/team/team.c:1947

stack backtrace:
CPU: 1 PID: 6391 Comm: syz-executor4 Not tainted 4.18.0-rc7+ #176
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
 print_deadlock_bug kernel/locking/lockdep.c:1765 [inline]
 check_deadlock kernel/locking/lockdep.c:1809 [inline]
 validate_chain kernel/locking/lockdep.c:2405 [inline]
 __lock_acquire.cold.64+0x1fb/0x486 kernel/locking/lockdep.c:3435
 lock_acquire+0x1e4/0x540 kernel/locking/lockdep.c:3924
 __mutex_lock_common kernel/locking/mutex.c:757 [inline]
 __mutex_lock+0x176/0x1820 kernel/locking/mutex.c:894
 mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:909
 team_vlan_rx_add_vid+0x3b/0x1e0 drivers/net/team/team.c:1868
 vlan_add_rx_filter_info+0x14a/0x1d0 net/8021q/vlan_core.c:210
 __vlan_vid_add net/8021q/vlan_core.c:278 [inline]
 vlan_vid_add+0x63e/0x9d0 net/8021q/vlan_core.c:308
 vlan_device_event.cold.12+0x2a/0x2f net/8021q/vlan.c:381
 notifier_call_chain+0x180/0x390 kernel/notifier.c:93
 __raw_notifier_call_chain kernel/notifier.c:394 [inline]
 raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1735
 call_netdevice_notifiers net/core/dev.c:1753 [inline]
 dev_open+0x173/0x1b0 net/core/dev.c:1433
 team_port_add drivers/net/team/team.c:1219 [inline]
 team_add_slave+0xa8b/0x1c30 drivers/net/team/team.c:1948
 do_set_master+0x1c9/0x220 net/core/rtnetlink.c:2248
 do_setlink+0xba4/0x3e10 net/core/rtnetlink.c:2382
 rtnl_setlink+0x2a9/0x400 net/core/rtnetlink.c:2636
 rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4665
 netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2455
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4683
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0xa18/0xfd0 net/netlink/af_netlink.c:1908
 sock_sendmsg_nosec net/socket.c:642 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:652
 ___sys_sendmsg+0x7fd/0x930 net/socket.c:2126
 __sys_sendmsg+0x11d/0x290 net/socket.c:2164
 __do_sys_sendmsg net/socket.c:2173 [inline]
 __se_sys_sendmsg net/socket.c:2171 [inline]
 __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2171
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x456b29
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f9706bf8c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f9706bf96d4 RCX: 0000000000456b29
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000004
RBP: 00000000009300a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d3548 R14: 00000000004c8227 R15: 0000000000000000

Fixes: 87002b03 ("net: introduce vlan_vid_[add/del] and use them instead of direct [add/kill]_vid ndo calls")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-and-tested-by: syzbot+bd051aba086537515cdb@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d7ab5cdc ]

When processing pmtu update from an icmp packet, it calls .update_pmtu
with sk instead of skb in sctp_transport_update_pmtu.

However for sctp, the daddr in the transport might be different from
inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or
create the route cache. The incorrect daddr will cause a different
route cache created for the path.

So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr
should be updated with the daddr in the transport, and update it back
after it's done.

The issue has existed since route exceptions introduction.

Fixes: 4895c771 ("ipv4: Add FIB nexthop exceptions.")
Reported-by: ian.periam@dialogic.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 0e1d6eca ]

We have an impressive number of syzkaller bugs that are linked
to the fact that syzbot was able to create a networking device
with millions of TX (or RX) queues.

Let's limit the number of RX/TX queues to 4096, this really should
cover all known cases.

A separate patch will add various cond_resched() in the loops
handling sysfs entries at device creation and dismantle.

Tested:

lpaa6:~# ip link add gre-4097 numtxqueues 4097 numrxqueues 4097 type ip6gretap
RTNETLINK answers: Invalid argument

lpaa6:~# time ip link add gre-4096 numtxqueues 4096 numrxqueues 4096 type ip6gretap

real	0m0.180s
user	0m0.000s
sys	0m0.107s

Fixes: 76ff5cc9 ("rtnl: allow to specify number of rx and tx queues on device creation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit bd961c9b ]

Currently, rtnl_fdb_dump() assumes the family header is 'struct ifinfomsg',
which is not always true -- 'struct ndmsg' is used by iproute2 ('ip neigh').

The problem is, the function bails out early if nlmsg_parse() fails, which
does occur for iproute2 usage of 'struct ndmsg' because the payload length
is shorter than the family header alone (as 'struct ifinfomsg' is assumed).

This breaks backward compatibility with userspace -- nothing is sent back.

Some examples with iproute2 and netlink library for go [1]:

 1) $ bridge fdb show
    33:33:00:00:00:01 dev ens3 self permanent
    01:00:5e:00:00:01 dev ens3 self permanent
    33:33:ff:15:98:30 dev ens3 self permanent

      This one works, as it uses 'struct ifinfomsg'.

      fdb_show() @ iproute2/bridge/fdb.c
        """
        .n.nlmsg_len = NLMSG_LENGTH(sizeof(struct ifinfomsg)),
        ...
        if (rtnl_dump_request(&rth, RTM_GETNEIGH, [...]
        """

 2) $ ip --family bridge neigh
    RTNETLINK answers: Invalid argument
    Dump terminated

      This one fails, as it uses 'struct ndmsg'.

      do_show_or_flush() @ iproute2/ip/ipneigh.c
        """
        .n.nlmsg_type = RTM_GETNEIGH,
        .n.nlmsg_len = NLMSG_LENGTH(sizeof(struct ndmsg)),
        """

 3) $ ./neighlist
    < no output >

      This one fails, as it uses 'struct ndmsg'-based.

      neighList() @ netlink/neigh_linux.go
        """
        req := h.newNetlinkRequest(unix.RTM_GETNEIGH, [...]
        msg := Ndmsg{
        """

The actual breakage was introduced by commit 0ff50e83 ("net: rtnetlink:
bail out from rtnl_fdb_dump() on parse error"), because nlmsg_parse() fails
if the payload length (with the _actual_ family header) is less than the
family header length alone (which is assumed, in parameter 'hdrlen').
This is true in the examples above with struct ndmsg, with size and payload
length shorter than struct ifinfomsg.

However, that commit just intends to fix something under the assumption the
family header is indeed an 'struct ifinfomsg' - by preventing access to the
payload as such (via 'ifm' pointer) if the payload length is not sufficient
to actually contain it.

The assumption was introduced by commit 5e6d2435 ("bridge: netlink dump
interface at par with brctl"), to support iproute2's 'bridge fdb' command
(not 'ip neigh') which indeed uses 'struct ifinfomsg', thus is not broken.

So, in order to unbreak the 'struct ndmsg' family headers and still allow
'struct ifinfomsg' to continue to work, check for the known message sizes
used with 'struct ndmsg' in iproute2 (with zero or one attribute which is
not used in this function anyway) then do not parse the data as ifinfomsg.

Same examples with this patch applied (or revert/before the original fix):

    $ bridge fdb show
    33:33:00:00:00:01 dev ens3 self permanent
    01:00:5e:00:00:01 dev ens3 self permanent
    33:33:ff:15:98:30 dev ens3 self permanent

    $ ip --family bridge neigh
    dev ens3 lladdr 33:33:00:00:00:01 PERMANENT
    dev ens3 lladdr 01:00:5e:00:00:01 PERMANENT
    dev ens3 lladdr 33:33:ff:15:98:30 PERMANENT

    $ ./neighlist
    netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x33, 0x33, 0x0, 0x0, 0x0, 0x1}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
    netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x1, 0x0, 0x5e, 0x0, 0x0, 0x1}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}
    netlink.Neigh{LinkIndex:2, Family:7, State:128, Type:0, Flags:2, IP:net.IP(nil), HardwareAddr:net.HardwareAddr{0x33, 0x33, 0xff, 0x15, 0x98, 0x30}, LLIPAddr:net.IP(nil), Vlan:0, VNI:0}

Tested on mainline (v4.19-rc6) and net-next (3bd09b05).

References:

[1] netlink library for go (test-case)
    https://github.com/vishvananda/netlink

    $ cat ~/go/src/neighlist/main.go
    package main
    import ("fmt"; "syscall"; "github.com/vishvananda/netlink")
    func main() {
        neighs, _ := netlink.NeighList(0, syscall.AF_BRIDGE)
        for _, neigh := range neighs { fmt.Printf("%#v\n", neigh) }
    }

    $ export GOPATH=~/go
    $ go get github.com/vishvananda/netlink
    $ go build neighlist
    $ ~/go/src/neighlist/neighlist

Thanks to David Ahern for suggestions to improve this patch.

Fixes: 0ff50e83 ("net: rtnetlink: bail out from rtnl_fdb_dump() on parse error")
Fixes: 5e6d2435 ("bridge: netlink dump interface at par with brctl")
Reported-by: Aidan Obley <aobley@pivotal.io>
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4f761770 ]

Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c333fa0c ]

In regular NIC transmission flow, driver always configures MAC using
Tx queue zero descriptor as a part of MAC learning flow.
But with multi Tx queue supported NIC, regular transmission can occur on
any non-zero Tx queue and from that context it uses
Tx queue zero descriptor to configure MAC, at the same time TX queue
zero could be used by another CPU for regular transmission
which could lead to Tx queue zero descriptor corruption and cause FW
abort.

This patch fixes this in such a way that driver always configures
learned MAC address from the same Tx queue which is used for
regular transmission.

Fixes: 7e2cf4fe ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f7b2a56e ]

Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
 smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
 process_one_work+0x18d/0x2fc
 worker_thread+0x1a2/0x269
 ? pr_cont_work+0x58/0x58
 kthread+0xfa/0x10a
 ? pr_cont_work+0x58/0x58
 ? rcu_read_unlock_sched_notrace+0x48/0x48
 ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 45ec3185 ]

The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.

The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.

This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.

The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.

Fixes: bb9051a2 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8b4c3cdd ]

A number of TC attributes are processed without proper validation
(e.g., length checks). Add a tca policy for all input attributes and use
when invoking nlmsg_parse.

The 2 Fixes tags below cover the latest additions. The other attributes
are a string (KIND), nested attribute (OPTIONS which does seem to have
validation in most cases), for dumps only or a flag.

Fixes: 5bc17018 ("net: sched: introduce multichain support for filters")
Fixes: d47a6b0e ("net: sched: introduce ingress/egress block index attributes for qdisc")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 774268f3 ]

When no Tx IRQ is available, the txq_done() routine (called from
tx_done()) shouldn't be called from the polling function, as in such
case it is already called in the Tx path thanks to an hrtimer. This
mostly occurred when using PPv2.1, as the engine then do not have Tx
IRQs.

Fixes: edc660fa ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 35f3625c ]

When offloading the L3 and L4 csum computation on TX, we need to extract
the l3_proto from the ethtype, independently of the presence of a vlan
tag.

The actual driver uses skb->protocol as-is, resulting in packets with
the wrong L4 checksum being sent when there's a vlan tag in the packet
header and checksum offloading is enabled.

This commit makes use of vlan_protocol_get() to get the correct ethtype
regardless the presence of a vlan tag.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f88b4c01 ]

netlbl_unlabel_addrinfo_get() assumes that if it finds the
NLBL_UNLABEL_A_IPV4ADDR attribute, it must also have the
NLBL_UNLABEL_A_IPV4MASK attribute as well. However, this is
not necessarily the case as the current checks in
netlbl_unlabel_staticadd() and friends are not sufficent to
enforce this.

If passed a netlink message with NLBL_UNLABEL_A_IPV4ADDR,
NLBL_UNLABEL_A_IPV6ADDR, and NLBL_UNLABEL_A_IPV6MASK attributes,
these functions will all call netlbl_unlabel_addrinfo_get() which
will then attempt dereference NULL when fetching the non-existent
NLBL_UNLABEL_A_IPV4MASK attribute:

Unable to handle kernel NULL pointer dereference at virtual address 0
Process unlab (pid: 31762, stack limit = 0xffffff80502d8000)
Call trace:
	netlbl_unlabel_addrinfo_get+0x44/0xd8
	netlbl_unlabel_staticremovedef+0x98/0xe0
	genl_rcv_msg+0x354/0x388
	netlink_rcv_skb+0xac/0x118
	genl_rcv+0x34/0x48
	netlink_unicast+0x158/0x1f0
	netlink_sendmsg+0x32c/0x338
	sock_sendmsg+0x44/0x60
	___sys_sendmsg+0x1d0/0x2a8
	__sys_sendmsg+0x64/0xb4
	SyS_sendmsg+0x34/0x4c
	el0_svc_naked+0x34/0x38
Code: 51001149 7100113f 540000a0 f9401508 (79400108)
---[ end trace f6438a488e737143 ]---
Kernel panic - not syncing: Fatal exception
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 86f9bd1f ]

The backend handling for /proc/net/if_inet6 in addrconf.c doesn't properly
handle starting/stopping the iteration.  The problem is that at some point
during the iteration, an overflow is detected and the process is
subsequently stopped.  The item being shown via seq_printf() when the
overflow occurs is not actually shown, though.  When start() is
subsequently called to resume iterating, it returns the next item, and
thus the item that was being processed when the overflow occurred never
gets printed.

Alter the meaning of the private data member "offset".  Currently, when it
is not 0 (which only happens at the very beginning), "offset" represents
the next hlist item to be printed.  After this change, "offset" always
represents the current item.

This is also consistent with the private data member "bucket", which
represents the current bucket, and also the use of "pos" as defined in
seq_file.txt:
    The pos passed to start() will always be either zero, or the most
    recent pos used in the previous session.
Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit af7d6cce ]

Since commit 5aad1de5 ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.

As Stefano described in commit e9fa1495 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
 - if the local MTU is now lower than the PMTU, that PMTU is now
   incorrect
 - if the local MTU was the lowest value in the path, and is increased,
   we might discover a higher PMTU

Similarly to what commit e9fa1495 did for IPv6, update PMTU in those
cases.

If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.

To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.

Fixes: 5aad1de5 ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2e9361ef ]

If SMMU is on, there is more likely that skb_shinfo(skb)->frags[i]
can not send by a single BD. when this happen, the
hns_nic_net_xmit_hw function map the whole data in a frags using
skb_frag_dma_map, but unmap each BD' data individually when tx is
done, which causes problem when SMMU is on.

This patch fixes this problem by ummapping the whole data in a
frags when tx is done.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 54baca09 ]

There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.

Fixes: 8cfa9498 ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a688caa3 ]

In rawv6_send_hdrinc(), in order to avoid an extra dst_hold(), we
directly assign the dst to skb and set passed in dst to NULL to avoid
double free.
However, in error case, we free skb and then do stats update with the
dst pointer passed in. This causes use-after-free on the dst.
Fix it by taking rcu read lock right before dst could get released to
make sure dst does not get freed until the stats update is done.
Note: we don't have this issue in ipv4 cause dst is not used for stats
update in v4.

Syzkaller reported following crash:
BUG: KASAN: use-after-free in rawv6_send_hdrinc net/ipv6/raw.c:692 [inline]
BUG: KASAN: use-after-free in rawv6_sendmsg+0x4421/0x4630 net/ipv6/raw.c:921
Read of size 8 at addr ffff8801d95ba730 by task syz-executor0/32088

CPU: 1 PID: 32088 Comm: syz-executor0 Not tainted 4.19.0-rc2+ #93
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c4/0x2b4 lib/dump_stack.c:113
 print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
 kasan_report_error mm/kasan/report.c:354 [inline]
 kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report.c:433
 rawv6_send_hdrinc net/ipv6/raw.c:692 [inline]
 rawv6_sendmsg+0x4421/0x4630 net/ipv6/raw.c:921
 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:631
 ___sys_sendmsg+0x7fd/0x930 net/socket.c:2114
 __sys_sendmsg+0x11d/0x280 net/socket.c:2152
 __do_sys_sendmsg net/socket.c:2161 [inline]
 __se_sys_sendmsg net/socket.c:2159 [inline]
 __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2159
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457099
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f83756edc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f83756ee6d4 RCX: 0000000000457099
RDX: 0000000000000000 RSI: 0000000020003840 RDI: 0000000000000004
RBP: 00000000009300a0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d4b30 R14: 00000000004c90b1 R15: 0000000000000000

Allocated by task 32088:
 save_stack+0x43/0xd0 mm/kasan/kasan.c:448
 set_track mm/kasan/kasan.c:460 [inline]
 kasan_kmalloc+0xc7/0xe0 mm/kasan/kasan.c:553
 kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:490
 kmem_cache_alloc+0x12e/0x730 mm/slab.c:3554
 dst_alloc+0xbb/0x1d0 net/core/dst.c:105
 ip6_dst_alloc+0x35/0xa0 net/ipv6/route.c:353
 ip6_rt_cache_alloc+0x247/0x7b0 net/ipv6/route.c:1186
 ip6_pol_route+0x8f8/0xd90 net/ipv6/route.c:1895
 ip6_pol_route_output+0x54/0x70 net/ipv6/route.c:2093
 fib6_rule_lookup+0x277/0x860 net/ipv6/fib6_rules.c:122
 ip6_route_output_flags+0x2c5/0x350 net/ipv6/route.c:2121
 ip6_route_output include/net/ip6_route.h:88 [inline]
 ip6_dst_lookup_tail+0xe27/0x1d60 net/ipv6/ip6_output.c:951
 ip6_dst_lookup_flow+0xc8/0x270 net/ipv6/ip6_output.c:1079
 rawv6_sendmsg+0x12d9/0x4630 net/ipv6/raw.c:905
 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:621 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:631
 ___sys_sendmsg+0x7fd/0x930 net/socket.c:2114
 __sys_sendmsg+0x11d/0x280 net/socket.c:2152
 __do_sys_sendmsg net/socket.c:2161 [inline]
 __se_sys_sendmsg net/socket.c:2159 [inline]
 __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2159
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 5356:
 save_stack+0x43/0xd0 mm/kasan/kasan.c:448
 set_track mm/kasan/kasan.c:460 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/kasan.c:521
 kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
 __cache_free mm/slab.c:3498 [inline]
 kmem_cache_free+0x83/0x290 mm/slab.c:3756
 dst_destroy+0x267/0x3c0 net/core/dst.c:141
 dst_destroy_rcu+0x16/0x19 net/core/dst.c:154
 __rcu_reclaim kernel/rcu/rcu.h:236 [inline]
 rcu_do_batch kernel/rcu/tree.c:2576 [inline]
 invoke_rcu_callbacks kernel/rcu/tree.c:2880 [inline]
 __rcu_process_callbacks kernel/rcu/tree.c:2847 [inline]
 rcu_process_callbacks+0xf23/0x2670 kernel/rcu/tree.c:2864
 __do_softirq+0x30b/0xad8 kernel/softirq.c:292

Fixes: 1789a640 ("raw: avoid two atomics in xmit")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 64199fc0 ]

Caching ip_hdr(skb) before a call to pskb_may_pull() is buggy,
do not do it.

Fixes: 2efd4fca ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ccfec9e5]

Cong noted that we need the same checks introduced by commit 76c0ddd8
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.

Fixes: c5441932 ("GRE: Refactor GRE tunneling code.")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 76c0ddd8 ]

the ip6 tunnel xmit ndo assumes that the processed skb always
contains an ip[v6] header, but syzbot has found a way to send
frames that fall short of this assumption, leading to the following splat:

BUG: KMSAN: uninit-value in ip6ip6_tnl_xmit net/ipv6/ip6_tunnel.c:1307
[inline]
BUG: KMSAN: uninit-value in ip6_tnl_start_xmit+0x7d2/0x1ef0
net/ipv6/ip6_tunnel.c:1390
CPU: 0 PID: 4504 Comm: syz-executor558 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
  __dump_stack lib/dump_stack.c:17 [inline]
  dump_stack+0x185/0x1d0 lib/dump_stack.c:53
  kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
  __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
  ip6ip6_tnl_xmit net/ipv6/ip6_tunnel.c:1307 [inline]
  ip6_tnl_start_xmit+0x7d2/0x1ef0 net/ipv6/ip6_tunnel.c:1390
  __netdev_start_xmit include/linux/netdevice.h:4066 [inline]
  netdev_start_xmit include/linux/netdevice.h:4075 [inline]
  xmit_one net/core/dev.c:3026 [inline]
  dev_hard_start_xmit+0x5f1/0xc70 net/core/dev.c:3042
  __dev_queue_xmit+0x27ee/0x3520 net/core/dev.c:3557
  dev_queue_xmit+0x4b/0x60 net/core/dev.c:3590
  packet_snd net/packet/af_packet.c:2944 [inline]
  packet_sendmsg+0x7c70/0x8a30 net/packet/af_packet.c:2969
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg net/socket.c:640 [inline]
  ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
  __sys_sendmmsg+0x42d/0x800 net/socket.c:2136
  SYSC_sendmmsg+0xc4/0x110 net/socket.c:2167
  SyS_sendmmsg+0x63/0x90 net/socket.c:2162
  do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x441819
RSP: 002b:00007ffe58ee8268 EFLAGS: 00000213 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000441819
RDX: 0000000000000002 RSI: 0000000020000100 RDI: 0000000000000003
RBP: 00000000006cd018 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000402510
R13: 00000000004025a0 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
  kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
  kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
  kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
  kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
  slab_post_alloc_hook mm/slab.h:445 [inline]
  slab_alloc_node mm/slub.c:2737 [inline]
  __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
  __kmalloc_reserve net/core/skbuff.c:138 [inline]
  __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
  alloc_skb include/linux/skbuff.h:984 [inline]
  alloc_skb_with_frags+0x1d4/0xb20 net/core/skbuff.c:5234
  sock_alloc_send_pskb+0xb56/0x1190 net/core/sock.c:2085
  packet_alloc_skb net/packet/af_packet.c:2803 [inline]
  packet_snd net/packet/af_packet.c:2894 [inline]
  packet_sendmsg+0x6454/0x8a30 net/packet/af_packet.c:2969
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg net/socket.c:640 [inline]
  ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
  __sys_sendmmsg+0x42d/0x800 net/socket.c:2136
  SYSC_sendmmsg+0xc4/0x110 net/socket.c:2167
  SyS_sendmmsg+0x63/0x90 net/socket.c:2162
  do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2

This change addresses the issue adding the needed check before
accessing the inner header.

The ipv4 side of the issue is apparently there since the ipv4 over ipv6
initial support, and the ipv6 side predates git history.

Fixes: c4d3efaf ("[IPV6] IP6TUNNEL: Add support to IPv4 over IPv6 tunnel.")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+3fde91d4d394747d6db4@syzkaller.appspotmail.com
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d4859d74 ]

Syzkaller reported this on a slightly older kernel but it's still
applicable to the current kernel -

======================================================
WARNING: possible circular locking dependency detected
4.18.0-next-20180823+ #46 Not tainted
------------------------------------------------------
syz-executor4/26841 is trying to acquire lock:
00000000dd41ef48 ((wq_completion)bond_dev->name){+.+.}, at: flush_workqueue+0x2db/0x1e10 kernel/workqueue.c:2652

but task is already holding lock:
00000000768ab431 (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
00000000768ab431 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4708

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (rtnl_mutex){+.+.}:
       __mutex_lock_common kernel/locking/mutex.c:925 [inline]
       __mutex_lock+0x171/0x1700 kernel/locking/mutex.c:1073
       mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:1088
       rtnl_lock+0x17/0x20 net/core/rtnetlink.c:77
       bond_netdev_notify drivers/net/bonding/bond_main.c:1310 [inline]
       bond_netdev_notify_work+0x44/0xd0 drivers/net/bonding/bond_main.c:1320
       process_one_work+0xc73/0x1aa0 kernel/workqueue.c:2153
       worker_thread+0x189/0x13c0 kernel/workqueue.c:2296
       kthread+0x35a/0x420 kernel/kthread.c:246
       ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415

-> #1 ((work_completion)(&(&nnw->work)->work)){+.+.}:
       process_one_work+0xc0b/0x1aa0 kernel/workqueue.c:2129
       worker_thread+0x189/0x13c0 kernel/workqueue.c:2296
       kthread+0x35a/0x420 kernel/kthread.c:246
       ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415

-> #0 ((wq_completion)bond_dev->name){+.+.}:
       lock_acquire+0x1e4/0x4f0 kernel/locking/lockdep.c:3901
       flush_workqueue+0x30a/0x1e10 kernel/workqueue.c:2655
       drain_workqueue+0x2a9/0x640 kernel/workqueue.c:2820
       destroy_workqueue+0xc6/0x9d0 kernel/workqueue.c:4155
       __alloc_workqueue_key+0xef9/0x1190 kernel/workqueue.c:4138
       bond_init+0x269/0x940 drivers/net/bonding/bond_main.c:4734
       register_netdevice+0x337/0x1100 net/core/dev.c:8410
       bond_newlink+0x49/0xa0 drivers/net/bonding/bond_netlink.c:453
       rtnl_newlink+0xef4/0x1d50 net/core/rtnetlink.c:3099
       rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4711
       netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2454
       rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4729
       netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
       netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
       netlink_sendmsg+0xa18/0xfc0 net/netlink/af_netlink.c:1908
       sock_sendmsg_nosec net/socket.c:622 [inline]
       sock_sendmsg+0xd5/0x120 net/socket.c:632
       ___sys_sendmsg+0x7fd/0x930 net/socket.c:2115
       __sys_sendmsg+0x11d/0x290 net/socket.c:2153
       __do_sys_sendmsg net/socket.c:2162 [inline]
       __se_sys_sendmsg net/socket.c:2160 [inline]
       __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2160
       do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
       entry_SYSCALL_64_after_hwframe+0x49/0xbe

other info that might help us debug this:

Chain exists of:
  (wq_completion)bond_dev->name --> (work_completion)(&(&nnw->work)->work) --> rtnl_mutex

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(rtnl_mutex);
                               lock((work_completion)(&(&nnw->work)->work));
                               lock(rtnl_mutex);
  lock((wq_completion)bond_dev->name);

 *** DEADLOCK ***

1 lock held by syz-executor4/26841:

stack backtrace:
CPU: 1 PID: 26841 Comm: syz-executor4 Not tainted 4.18.0-next-20180823+ #46
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
 print_circular_bug.isra.34.cold.55+0x1bd/0x27d kernel/locking/lockdep.c:1222
 check_prev_add kernel/locking/lockdep.c:1862 [inline]
 check_prevs_add kernel/locking/lockdep.c:1975 [inline]
 validate_chain kernel/locking/lockdep.c:2416 [inline]
 __lock_acquire+0x3449/0x5020 kernel/locking/lockdep.c:3412
 lock_acquire+0x1e4/0x4f0 kernel/locking/lockdep.c:3901
 flush_workqueue+0x30a/0x1e10 kernel/workqueue.c:2655
 drain_workqueue+0x2a9/0x640 kernel/workqueue.c:2820
 destroy_workqueue+0xc6/0x9d0 kernel/workqueue.c:4155
 __alloc_workqueue_key+0xef9/0x1190 kernel/workqueue.c:4138
 bond_init+0x269/0x940 drivers/net/bonding/bond_main.c:4734
 register_netdevice+0x337/0x1100 net/core/dev.c:8410
 bond_newlink+0x49/0xa0 drivers/net/bonding/bond_netlink.c:453
 rtnl_newlink+0xef4/0x1d50 net/core/rtnetlink.c:3099
 rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4711
 netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2454
 rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4729
 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
 netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
 netlink_sendmsg+0xa18/0xfc0 net/netlink/af_netlink.c:1908
 sock_sendmsg_nosec net/socket.c:622 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:632
 ___sys_sendmsg+0x7fd/0x930 net/socket.c:2115
 __sys_sendmsg+0x11d/0x290 net/socket.c:2153
 __do_sys_sendmsg net/socket.c:2162 [inline]
 __se_sys_sendmsg net/socket.c:2160 [inline]
 __x64_sys_sendmsg+0x78/0xb0 net/socket.c:2160
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457089
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f2df20a5c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f2df20a66d4 RCX: 0000000000457089
RDX: 0000000000000000 RSI: 0000000020000180 RDI: 0000000000000003
RBP: 0000000000930140 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d40b8 R14: 00000000004c8ad8 R15: 0000000000000001
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a2bf74f4 ]

When the driver probe fails, all the resources that were allocated prior
to the failure must be freed. However, hwrm dma response memory is not
getting freed.

This patch fixes the problem described above.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 73f21c65 ]

The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events.  bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting.  In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.

We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.

Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c8291988 upstream.

Length of WMI scan message was not calculated correctly. The allocated
buffer was smaller than what we expected. So WMI message corrupted
skb_info, which is at the end of skb->data. This fix takes TLV header
into account even if the element is zero-length.

Crash log:
  [49.629986] Unhandled kernel unaligned access[#1]:
  [49.634932] CPU: 0 PID: 1176 Comm: logd Not tainted 4.4.60 #180
  [49.641040] task: 83051460 ti: 8329c000 task.ti: 8329c000
  [49.646608] $ 0   : 00000000 00000001 80984a80 00000000
  [49.652038] $ 4   : 45259e89 8046d484 8046df30 8024ba70
  [49.657468] $ 8   : 00000000 804cc4c0 00000001 20306320
  [49.662898] $12   : 33322037 000110f2 00000000 31203930
  [49.668327] $16   : 82792b40 80984a80 00000001 804207fc
  [49.673757] $20   : 00000000 0000012c 00000040 80470000
  [49.679186] $24   : 00000000 8024af7c
  [49.684617] $28   : 8329c000 8329db88 00000001 802c58d0
  [49.690046] Hi    : 00000000
  [49.693022] Lo    : 453c0000
  [49.696013] epc   : 800efae4 put_page+0x0/0x58
  [49.700615] ra    : 802c58d0 skb_release_data+0x148/0x1d4
  [49.706184] Status: 1000fc03 KERNEL EXL IE
  [49.710531] Cause : 00800010 (ExcCode 04)
  [49.714669] BadVA : 45259e89
  [49.717644] PrId  : 00019374 (MIPS 24Kc)
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d9e427f6 upstream.

commit c7cdff0e ("virtio_balloon: fix deadlock on OOM")
changed code to increment vb->num_pfns before call to
set_page_pfns(), which used to happen only after.

This patch fixes boot hang for me on ppc64le KVM guests.

Fixes: c7cdff0e ("virtio_balloon: fix deadlock on OOM")
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Wei Wang <wei.w.wang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c7cdff0e upstream.

fill_balloon doing memory allocations under balloon_lock
can cause a deadlock when leak_balloon is called from
virtballoon_oom_notify and tries to take same lock.

To fix, split page allocation and enqueue and do allocations outside the lock.

Here's a detailed analysis of the deadlock by Tetsuo Handa:

In leak_balloon(), mutex_lock(&vb->balloon_lock) is called in order to
serialize against fill_balloon(). But in fill_balloon(),
alloc_page(GFP_HIGHUSER[_MOVABLE] | __GFP_NOMEMALLOC | __GFP_NORETRY) is
called with vb->balloon_lock mutex held. Since GFP_HIGHUSER[_MOVABLE]
implies __GFP_DIRECT_RECLAIM | __GFP_IO | __GFP_FS, despite __GFP_NORETRY
is specified, this allocation attempt might indirectly depend on somebody
else's __GFP_DIRECT_RECLAIM memory allocation. And such indirect
__GFP_DIRECT_RECLAIM memory allocation might call leak_balloon() via
virtballoon_oom_notify() via blocking_notifier_call_chain() callback via
out_of_memory() when it reached __alloc_pages_may_oom() and held oom_lock
mutex. Since vb->balloon_lock mutex is already held by fill_balloon(), it
will cause OOM lockup.

  Thread1                                       Thread2
    fill_balloon()
      takes a balloon_lock
      balloon_page_enqueue()
        alloc_page(GFP_HIGHUSER_MOVABLE)
          direct reclaim (__GFP_FS context)       takes a fs lock
            waits for that fs lock                  alloc_page(GFP_NOFS)
                                                      __alloc_pages_may_oom()
                                                        takes the oom_lock
                                                        out_of_memory()
                                                          blocking_notifier_call_chain()
                                                            leak_balloon()
                                                              tries to take that balloon_lock and deadlocks
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f394ad28 upstream.

Currently, rds_ib_conn_alloc() calls rds_ib_recv_alloc_caches()
without passing along the gfp_t flag.  But rds_ib_recv_alloc_caches()
and rds_ib_recv_alloc_cache() should take a gfp_t parameter so that
rds_ib_recv_alloc_cache() can call alloc_percpu_gfp() using the
correct flag instead of calling alloc_percpu().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 37f31b6c upstream.

The requested device name can be NULL or an empty string.
Check for that and refuse to continue. UBIFS has to do this manually
since we cannot use mount_bdev(), which checks for this condition.

Fixes: 1e51764a ("UBIFS: add new flash file system")
Reported-by: syzbot+38bd0f7865e5c6379280@syzkaller.appspotmail.com
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5fe23f26 upstream.

There is a race condition between ucma_close() and ucma_resolve_ip():

CPU0				CPU1
ucma_resolve_ip():		ucma_close():

ctx = ucma_get_ctx(file, cmd.id);

        list_for_each_entry_safe(ctx, tmp, &file->ctx_list, list) {
                mutex_lock(&mut);
                idr_remove(&ctx_idr, ctx->id);
                mutex_unlock(&mut);
		...
                mutex_lock(&mut);
                if (!ctx->closing) {
                        mutex_unlock(&mut);
                        rdma_destroy_id(ctx->cm_id);
		...
                ucma_free_ctx(ctx);

ret = rdma_resolve_addr();
ucma_put_ctx(ctx);

Before idr_remove(), ucma_get_ctx() could still find the ctx
and after rdma_destroy_id(), rdma_resolve_addr() may still
access id_priv pointer. Also, ucma_put_ctx() may use ctx after
ucma_free_ctx() too.

ucma_close() should call ucma_put_ctx() too which tests the
refcnt and waits for the last one releasing it. The similar
pattern is already used by ucma_destroy_id().

Reported-and-tested-by: syzbot+da2591e115d57a9cbb8b@syzkaller.appspotmail.com
Reported-by: syzbot+cfe3c1e8ef634ba8964b@syzkaller.appspotmail.com
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d3f07c04 upstream.

syzbot found the following crash on:

HEAD commit:    d9bd94c0bcaa Add linux-next specific files for 20180801
git tree:       linux-next
console output: https://syzkaller.appspot.com/x/log.txt?x=1001189c400000
kernel config:  https://syzkaller.appspot.com/x/.config?x=cc8964ea4d04518c
dashboard link: https://syzkaller.appspot.com/bug?extid=c966a82db0b14aa37e81
compiler:       gcc (GCC) 8.0.1 20180413 (experimental)

Unfortunately, I don't have any reproducer for this crash yet.

IMPORTANT: if you fix the bug, please add the following tag to the commit:
Reported-by: syzbot+c966a82db0b14aa37e81@syzkaller.appspotmail.com

loop7: rw=12288, want=8200, limit=20
netlink: 65342 bytes leftover after parsing attributes in process `syz-executor4'.
openvswitch: netlink: Message has 8 unknown bytes.
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
CPU: 1 PID: 7615 Comm: syz-executor7 Not tainted 4.18.0-rc7-next-20180801+ #29
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__read_once_size include/linux/compiler.h:188 [inline]
RIP: 0010:compound_head include/linux/page-flags.h:142 [inline]
RIP: 0010:PageLocked include/linux/page-flags.h:272 [inline]
RIP: 0010:f2fs_put_page fs/f2fs/f2fs.h:2011 [inline]
RIP: 0010:validate_checkpoint+0x66d/0xec0 fs/f2fs/checkpoint.c:835
Code: e8 58 05 7f fe 4c 8d 6b 80 4d 8d 74 24 08 48 b8 00 00 00 00 00 fc ff df 4c 89 ea 48 c1 ea 03 c6 04 02 00 4c 89 f2 48 c1 ea 03 <80> 3c 02 00 0f 85 f4 06 00 00 4c 89 ea 4d 8b 7c 24 08 48 b8 00 00
RSP: 0018:ffff8801937cebe8 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff8801937cef30 RCX: ffffc90006035000
RDX: 0000000000000000 RSI: ffffffff82fd9658 RDI: 0000000000000005
RBP: ffff8801937cef58 R08: ffff8801ab254700 R09: fffff94000d9e026
R10: fffff94000d9e026 R11: ffffea0006cf0137 R12: fffffffffffffffb
R13: ffff8801937ceeb0 R14: 0000000000000003 R15: ffff880193419b40
FS:  00007f36a61d5700(0000) GS:ffff8801db100000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc04ff93000 CR3: 00000001d0562000 CR4: 00000000001426e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 f2fs_get_valid_checkpoint+0x436/0x1ec0 fs/f2fs/checkpoint.c:860
 f2fs_fill_super+0x2d42/0x8110 fs/f2fs/super.c:2883
 mount_bdev+0x314/0x3e0 fs/super.c:1344
 f2fs_mount+0x3c/0x50 fs/f2fs/super.c:3133
 legacy_get_tree+0x131/0x460 fs/fs_context.c:729
 vfs_get_tree+0x1cb/0x5c0 fs/super.c:1743
 do_new_mount fs/namespace.c:2603 [inline]
 do_mount+0x6f2/0x1e20 fs/namespace.c:2927
 ksys_mount+0x12d/0x140 fs/namespace.c:3143
 __do_sys_mount fs/namespace.c:3157 [inline]
 __se_sys_mount fs/namespace.c:3154 [inline]
 __x64_sys_mount+0xbe/0x150 fs/namespace.c:3154
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x45943a
Code: b8 a6 00 00 00 0f 05 48 3d 01 f0 ff ff 0f 83 bd 8a fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 9a 8a fb ff c3 66 0f 1f 84 00 00 00 00 00
RSP: 002b:00007f36a61d4a88 EFLAGS: 00000206 ORIG_RAX: 00000000000000a5
RAX: ffffffffffffffda RBX: 00007f36a61d4b30 RCX: 000000000045943a
RDX: 00007f36a61d4ad0 RSI: 0000000020000100 RDI: 00007f36a61d4af0
RBP: 0000000020000100 R08: 00007f36a61d4b30 R09: 00007f36a61d4ad0
R10: 0000000000000000 R11: 0000000000000206 R12: 0000000000000013
R13: 0000000000000000 R14: 00000000004c8ea0 R15: 0000000000000000
Modules linked in:
Dumping ftrace buffer:
   (ftrace buffer empty)
---[ end trace bd8550c129352286 ]---
RIP: 0010:__read_once_size include/linux/compiler.h:188 [inline]
RIP: 0010:compound_head include/linux/page-flags.h:142 [inline]
RIP: 0010:PageLocked include/linux/page-flags.h:272 [inline]
RIP: 0010:f2fs_put_page fs/f2fs/f2fs.h:2011 [inline]
RIP: 0010:validate_checkpoint+0x66d/0xec0 fs/f2fs/checkpoint.c:835
Code: e8 58 05 7f fe 4c 8d 6b 80 4d 8d 74 24 08 48 b8 00 00 00 00 00 fc ff df 4c 89 ea 48 c1 ea 03 c6 04 02 00 4c 89 f2 48 c1 ea 03 <80> 3c 02 00 0f 85 f4 06 00 00 4c 89 ea 4d 8b 7c 24 08 48 b8 00 00
RSP: 0018:ffff8801937cebe8 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff8801937cef30 RCX: ffffc90006035000
RDX: 0000000000000000 RSI: ffffffff82fd9658 RDI: 0000000000000005
netlink: 65342 bytes leftover after parsing attributes in process `syz-executor4'.
RBP: ffff8801937cef58 R08: ffff8801ab254700 R09: fffff94000d9e026
openvswitch: netlink: Message has 8 unknown bytes.
R10: fffff94000d9e026 R11: ffffea0006cf0137 R12: fffffffffffffffb
R13: ffff8801937ceeb0 R14: 0000000000000003 R15: ffff880193419b40
FS:  00007f36a61d5700(0000) GS:ffff8801db100000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc04ff93000 CR3: 00000001d0562000 CR4: 00000000001426e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

In validate_checkpoint(), if we failed to call get_checkpoint_version(), we
will pass returned invalid page pointer into f2fs_put_page, cause accessing
invalid memory, this patch tries to handle error path correctly to fix this
issue.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>

commit 06c3f2aa upstream.

So that it can be used more widely, like in the next patch, when it will
be used to fix a bug in 'perf test' handling of dirent.d_type ==
DT_UNKNOWN.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171206174535.25380-1-jolsa@kernel.org
[ Split from a larger patch, removed needless includes in path.h ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit add92a81 upstream.

Update PCI Id in "cpl_rx_phys_dsgl" header. In case pci_chan_id and
tx_chan_id are not derived from same queue, H/W can send request
completion indication before completing DMA Transfer.

Herbert, It would be good if fix can be merge to stable tree.
For 4.14 kernel, It requires some update to avoid mege conficts.

Cc: <stable@vger.kernel.org>
Signed-off-by: Harsh Jain <harsh@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c58a584f upstream.

Per ARC TLS ABI, r25 is designated TP (thread pointer register).
However so far kernel didn't do any special treatment, like setting up
usermode r25, even for CLONE_SETTLS. We instead relied on libc runtime
to do this, in say clone libc wrapper [1]. This was deliberate to keep
kernel ABI agnostic (userspace could potentially change TP, specially
for different ARC ISA say ARCompact vs. ARCv2 with different spare
registers etc)

However userspace setting up r25, after clone syscall opens a race, if
child is not scheduled and gets a signal instead. It starts off in
userspace not in clone but in a signal handler and anything TP sepcific
there such as pthread_self() fails which showed up with uClibc
testsuite nptl/tst-kill6 [2]

Fix this by having kernel populate r25 to TP value. So this locks in
ABI, but it was not going to change anyways, and fwiw is same for both
ARCompact (arc700 core) and ARCvs (HS3x cores)

[1] https://cgit.uclibc-ng.org/cgi/cgit/uclibc-ng.git/tree/libc/sysdeps/linux/arc/clone.S
[2] https://github.com/wbx-github/uclibc-ng-test/blob/master/test/nptl/tst-kill6.c

Fixes: ARC STAR 9001378481
Cc: stable@vger.kernel.org
Reported-by: Nikita Sobolev <sobolev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>