After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Geminilake is new Intel SoC, so add codec entry for HDMI
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Geminilake is next gen SoC, so add the IDs for Geminilake.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Geminilake has two different devices connected to the same SSP, so use
device_type check to get correct device configuration.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Represent each port as machine DAPM pin widget. This helps in
enable/disable pin when monitor is connected/disconnected in case pcm
is rendered to multiple ports.

Create machine pin widgets  and pin switch kcontrol for each port and
report based on the pin status
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in bxt_da7219_max98357 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in bxt_rt298.c machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in skl_nau88l25_ssm4567 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in skl_nau88l25_max98357a machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Creates ASoC jack for HDMI pcm and calls hdmi codec API to initialize
jack in skl_rt268 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use snd_soc_jack instead of snd_jack and create the jack in machine
driver and pass the jack pointer to hdac_hdmi driver for jack
reporting.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Since we have the MST feature enabled and Pin-Port mux for user to
select the converter routing, multiple port mapping to same converter
needs to be supported.

To support multiple port mapped to same converter following changes are
done for this:.
o Add port list to pcm, so that multiple ports can be mapped to a PCM.
o Jack reporting in case where multiple port are attached to same PCM.
o Change hdac_hdmi_get_port_from_cvt(), channel_map, remove functions
to parse through all ports mapped to same the PCM.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To enable stream on a specific port of a MST capable pin, the port
needs to be selected before we configure the pin widget verb.

When port is selected, all the pin widget verb controlling the sink
device operation will be directed to selected port. So add port
selection before configuring the pin widget verb.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The ELD notification can be received asynchronously from the graphics
side and this may happen just at the moment the sound driver is
initializing and notification will be missed. Similarly at system
resume, the notification is ignored as the  ELD and connection states
are updated in anyway at the end of the resume.
So check the jack status in boot/resume by querying the port presence
based on pin caps and report the jack status.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To support DP MST audio, new pin verbs/params are added. This patch
adds helper functions to do following:
o To set a specific port
o To get the currently selected port
o To get the length of port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To handle jack event and configuration of the pin widget for MST
capable pin, this patch adds:
o Flag to identify the pin is MST capable.
o In notify callback(), based on the pipe and port information marks if
the port is mst_capable. In case of non MST, port is defaulted to zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To support MST moved pin to port, this changes the routes based on
port. So change the route in nau88l25_ssm4567 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To support MST moved pin to port, this changes the routes based on
port. So change the route in nau88l25_max98357a machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To support MST moved pin to port, this changes the routes based on
port. So change the route in bxt_rt298 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

With MST each pin contains several ports to which device can be
connected.

As a preparatory work to support DP MST this patch adds below changes:
1. Defines the port structure and moves all stream related information
   like ELD, converter list, chmap to port.
2. Creates ports for each pin based on the max_ports support.
3. Based on Pin-Port combination creates DAPM Mux widget instead of Pin
   to allow user to select a converter.
4. Port zero is the default port when pin does not support MST.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch create entry in sysfs file system to report the
platform_id = "pci-id-oem_id-oem_table_id-oem_revision"
for board identification.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.

Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To support MST moved pin to port, this changes the routes based on
port. So change the route in bxt_da7219_max98357a machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

To support MST moved pin to port, this changes the routes based on
port. So change the route in skl_rt286 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

HDMI registers channel map controls per pcm. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.

Register for late probe and call the jack_init API which registers
channel map in the late probe callback handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Channel info is part of the pcm parameter and channel map control is
created for each pcm. So move channel info to pcm instead of pin
structure and the mutex lock to pcm.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Missed unused variable in previous changes, oops.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Remove default and set I2S mode correctly both on codec and
cpu sides
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use ACPI ID 10EC3270 to load machine driver for cht-bsw-rt5645
and add reference to 3270 to use the rt5645 mode

Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Some platforms use AIF2, use routing information to set ASRC as needed
Suggested-by: Bard Liao <bardliao@realtek.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95681Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This driver may be used on Baytrail CR platforms where SSP2 is
not available.

Add quirks and routing detection based on work done for RT5640.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ALC3270 is a low-cost version of RT5645, add ACPI ID
to enable probe and use rt5645 codec driver
Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

the BIOS reports this codec as RT5640 but it's a rt5670. Use the
quirk mechanism to use the cht_bsw_rt5672 machine driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix classic issue of having multiple codecs listed in DSDT
but a single one actually enabled. The previous code did
not handle such errors and could also lead to uninitalized
configurations
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use machine driver initially defined for CherryTrail
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>