- 29 Sep, 2021 7 commits
-
-
Horatiu Vultur authored
The LAN8804 PHY has same features as that of LAN8814 PHY except that it doesn't support 1588, SyncE or Q-USGMII. This PHY is found inside the LAN966X switches. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/nexDavid S. Miller authored
t-queue Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2021-09-28 This series contains updates to ice driver only. Dave adds support for QoS DSCP allowing for DSCP to TC mapping via APP TLVs. Ani adds enforcement of DSCP to only supported devices with the introduction of a feature bitmap and corrects messaging of unsupported modules based on link mode. Jake refactors devlink info functions to be void as the functions no longer return errors. Jeff fixes a macro name to properly reflect the value. Len Baker converts a kzalloc allocation to, the preferred, kcalloc. ==================== Signed-off-by: -
David S. Miller authored
Subbaraya Sundeep <sbhatta@marvell.com> ==================== octeontx2: Add PTP support for VFs PTP is a shared hardware block which can prepend RX timestamps to packets before directing packets to PFs or VFs and can notify the TX timestamps to PFs or VFs via TX completion queue descriptors. Hence adding PTP support for VFs is exactly similar to PFs with minimal changes. This patchset adds that PTP support for VFs. Patch 1 - When an interface is set in promisc/multicast the same setting is not retained when changing mtu or channels. This is due to toggling of the interface by driver but not calling set_rx_mode in the down-up sequence. Since setting an interface to multicast properly is required for ptp this is addressed in this patch. Patch 2 - Changes in VF driver for registering timestamping ethtool ops and ndo_ioctl. ==================== Signed-off-by: -
Naveen Mamindlapalli authored
This patch adds PTP PHC support to NIX VF interfaces. This enables a VF to run PTP master/slave instance. PTP block being a shared hardware resource it is recommended to avoid running multiple PTP instances in the system which will impact the PTP clock accuracy. Signed-off-by:
Naveen Mamindlapalli <naveenm@marvell.com> Signed-off-by:
Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by:
Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by:
-
Rakesh Babu authored
Whenever the interface is brought up/down then set_rx_mode function is called by the stack which enables promisc/allmulti MCAM entries. But there are cases when driver brings interface down and then up such as while changing number of channels. In these cases promisc/allmulti MCAM entries are left disabled as set_rx_mode callback is not called. This patch enables these MCAM entries in all such cases. Signed-off-by:
Rakesh Babu <rsaladi2@marvell.com> Signed-off-by:
-
Luca Weiss authored
Previously with CONFIG_QRTR=m a separate ns.ko would be built which wasn't done on purpose and should be included in qrtr.ko. Rename qrtr.c to af_qrtr.c so we can build a qrtr.ko with both af_qrtr.c and ns.c. Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Tested-By:
Steev Klimaszewski <steev@kali.org> Reviewed-by:
Manivannan Sadhasivam <mani@kernel.org> Link: https://lore.kernel.org/r/20210928171156.6353-1-luca@z3ntu.xyzSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Mianhan Liu authored
fib_notifier.c hasn't use any macro or function declared in net/netns/ipv4.h. Thus, these files can be removed from fib_notifier.c safely without affecting the compilation of the net/ipv4 module. Signed-off-by:
Mianhan Liu <liumh1@shanghaitech.edu.cn> Link: https://lore.kernel.org/r/20210928164011.1454-1-liumh1@shanghaitech.edu.cnSigned-off-by:
-
- 28 Sep, 2021 21 commits
-
-
Len Baker authored
As noted in the "Deprecated Interfaces, Language Features, Attributes, and Conventions" documentation [1], size calculations (especially multiplication) should not be performed in memory allocator (or similar) function arguments due to the risk of them overflowing. This could lead to values wrapping around and a smaller allocation being made than the caller was expecting. Using those allocations could lead to linear overflows of heap memory and other misbehaviors. In this case this is not actually dynamic sizes: both sides of the multiplication are constant values. However it is best to refactor this anyway, just to keep the open-coded math idiom out of code. So, use the purpose specific kcalloc() function instead of the argument size * count in the kzalloc() function. [1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-argumentsSigned-off-by:
Len Baker <len.baker@gmx.com> Reviewed-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Jeff Guo authored
In IPv4 header, fragment flags indicate whether the packet needs to be fragmented or not. The value 0x20 represents MF (More Fragment); fix the macro name to match this. Signed-off-by:
Ting Xu <ting.xu@intel.com> Signed-off-by:
Jeff Guo <jia.guo@intel.com> Tested-by:
Gurucharan G <gurucharanx.g@intel.com> Signed-off-by:
-
Jacob Keller authored
After commit a8f89fa2 ("ice: do not abort devlink info if board identifier can't be found"), the getter/fallback() functions no longer report an error. Convert the interface to a void so that it is no longer possible to add a version field that is fatal. This makes sense, because we should not fail to report other versions just because one of the version pieces could not be found. Finally, clean up the getter functions line wrapping so that none of them take more than 80 columns, as is the usual style for networking files. Signed-off-by:
Jacob Keller <jacob.e.keller@intel.com> Tested-by:
Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by:
-
Anirudh Venkataramanan authored
The messaging for unsupported module detection is different for lenient mode and strict mode. Update the code to print the right messaging for a given link mode. Media topology conflict is not an error in lenient mode, so return an error code only if not in lenient mode. Signed-off-by:
Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by:
-
Anirudh Venkataramanan authored
DSCP a.k.a L3 QoS is only supported on certain devices. To enforce this, this patch introduces a bitmap of features and helper functions. The feature bitmap is set based on device IDs on driver init. Currently, DSCP is the only feature in this bitmap, but there will be more in the future. In the DCB netlink flow, check if the feature bit is set before exercising DSCP. Signed-off-by:
-
Dave Ertman authored
Implement code to handle submission of APP TLV's containing DSCP to TC mapping. The first such mapping received on an interface will cause that PF to switch to L3 DSCP QoS mode, apply the default config for that mode, and apply the received mapping. Only one such mapping will be allowed per DSCP value, and when the last DSCP mapping is deleted, the PF will switch back into L2 VLAN QoS mode, applying the appropriate default QoS settings. L3 DSCP QoS mode will only be allowed in SW DCBx mode, in other words, when the FW LLDP engine is disabled. Commands that break this mutual exclusivity will be blocked. Co-developed-by:
Dave Ertman <david.m.ertman@intel.com> Tested-by:
-
Arnd Bergmann authored
The use of dma_unmap_addr()/dma_unmap_len() in the driver causes multiple warnings when these macros are defined as empty, e.g. in an ARCH=i386 allmodconfig build: drivers/net/ethernet/google/gve/gve_tx_dqo.c: In function 'gve_tx_add_skb_no_copy_dqo': drivers/net/ethernet/google/gve/gve_tx_dqo.c:494:40: error: unused variable 'buf' [-Werror=unused-variable] 494 | struct gve_tx_dma_buf *buf = This is not how the NEED_DMA_MAP_STATE macros are meant to work, as they rely on never using local variables or a temporary structure like gve_tx_dma_buf. Remote the gve_tx_dma_buf definition and open-code the contents in all places to avoid the warning. This causes some rather long lines but otherwise ends up making the driver slightly smaller. Fixes: a57e5de4 ("gve: DQO: Add TX path") Link: https://lore.kernel.org/netdev/20210723231957.1113800-1-bcf@google.com/ Link: https://lore.kernel.org/netdev/20210721151100.2042139-1-arnd@kernel.org/Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Geetha sowjanya authored
Current driver uses software CQ head pointer to poll on CQE header in memory to determine if CQE is valid. Software needs to make sure, that the reads of the CQE do not get re-ordered so much that it ends up with an inconsistent view of the CQE. To ensure that DMB barrier after read to first CQE cacheline and before reading of the rest of the CQE is needed. But having barrier for every CQE read will impact the performance, instead use hardware CQ head and tail pointers to find the valid number of CQEs. Signed-off-by:
Geetha sowjanya <gakula@marvell.com> Signed-off-by:
-
David S. Miller authored
Hariprasad Kelam says: ==================== Externel ptp clock support Externel ptp support is required in a scenario like connecting a external timing device to the chip for time synchronization. This series of patches adds support to ptp driver to use external clock and enables PTP config in CN10K MAC block (RPM). Currently PTP configuration is left unchanged in FLR handler these patches addresses the same. ==================== Signed-off-by: -
Yi Guo authored
PTP hardware block can be configured to utilize the external clock. Also the current ptp timestamp can be captured when external trigger is applied on a gpio pin. These features are required in scenarios like connecting a external timing device to the chip for time synchronization. The timing device provides the clock and trigger(PPS signal) to the PTP block. This patch does the following: 1. configures PTP block to use external clock frequency and timestamp capture on external event. 2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem with captured timestamps 3. aligns PPS edge to adjusted ptp clock in the ptp device by setting the PPS_THRESH to the reminder of the last timestamp value captured by external PPS Signed-off-by:
Yi Guo <yig@marvell.com> Signed-off-by:
Hariprasad Kelam <hkelam@marvell.com> Signed-off-by:
-
Subbaraya Sundeep authored
The input clock frequency of PTP block is figured out from hardware reset block currently. The firmware data already has this info in sclk. Hence simplify ptp driver to use sclk from firmware data. Signed-off-by:
-
Hariprasad Kelam authored
MAC on CN10K support hardware timestamping such that 8 bytes addition header is prepended to incoming packets. This patch does necessary configuration to enable Hardware time stamping upon receiving request from PF netdev interfaces. Timestamp configuration is different on MAC (CGX) Octeontx2 silicon and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate fn() pointer is called. Refactor MAC specific mbox messages to remove unnecessary gaps in mboxids. Signed-off-by:
-
Harman Kalra authored
Upon receiving ptp config request from netdev interface , Octeontx2 MAC block CGX is configured to append timestamp to every incoming packet and NPC config is updated with DMAC offset change. Currently this configuration is not reset in FLR handler. This patch resets the same. Signed-off-by:
Harman Kalra <hkalra@marvell.com> Signed-off-by:
-
Tianjia Zhang authored
The IV of CCM mode has special requirements, this patch supports CCM mode of SM4 algorithm. Signed-off-by:
Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by:
-
Masahiro Yamada authored
Kbuild supports <modname>-y as well as <modname>-objs. This simplifies the Makefile. Signed-off-by:
Masahiro Yamada <masahiroy@kernel.org> Signed-off-by:
-
Masahiro Yamada authored
Assign the objects directly to obj-$(CONFIG_INET). Signed-off-by:
-
Arnd Bergmann authored
My previous patch had an off-by-one error in the added sanity check, the arrays are MTL_MAX_{RX,TX}_QUEUES long, so if that index is that number, it has overflown. The patch silenced the warning anyway because the strings could no longer overlap with the input, but they could still overlap with other fields. Fixes: 3e0d5699 ("net: stmmac: fix gcc-10 -Wrestrict warning") Reported-by:Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by:
-
Arnd Bergmann authored
clang warns about arithmetic on NULL pointers: drivers/net/ethernet/ti/am65-cpsw-ethtool.c:71:2: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction] AM65_CPSW_REGDUMP_REC(AM65_CPSW_REGDUMP_MOD_NUSS, 0x0, 0x1c), ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/ti/am65-cpsw-ethtool.c:64:29: note: expanded from macro 'AM65_CPSW_REGDUMP_REC' .hdr.len = (((u32 *)(end)) - ((u32 *)(start)) + 1) * sizeof(u32) * 2 + \ ^ ~~~~~~~~~~~~~~~~ The expression here is easily changed to a calculation based on integers that is no less readable. Signed-off-by: -
MichelleJin authored
When rhashtable_init() fails, it returns -EINVAL. However, since error return value of rhashtable_init is not checked, it can cause use of uninitialized pointers. So, fix unhandled errors of rhashtable_init. Signed-off-by:
MichelleJin <shjy180909@gmail.com> Signed-off-by:
-
MichelleJin authored
When rhashtable_init() fails, it returns -EINVAL. However, since error return value of rhashtable_init is not checked, it can cause use of uninitialized pointers. So, fix unhandled errors of rhashtable_init. Signed-off-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
MichelleJin authored
When rhashtable_init() fails, it returns -EINVAL. However, since error return value of rhashtable_init is not checked, it can cause use of uninitialized pointers. So, fix unhandled errors of rhashtable_init. Signed-off-by:
-
- 27 Sep, 2021 12 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== net: bcmgenet: support for flow control This patch series adds support for flow control to the GENET driver, the first 2 patches remove superfluous code, the 3rd one does re-organize code a little bit and the 4th one ads the support for flow control proper. ====================
-
Doug Berger authored
This commit extends the supported ethtool operations to allow MAC level flow control to be configured for the bcmgenet driver. The ethtool utility can be used to change the configuration of auto-negotiated symmetric and asymmetric modes as well as manually configuring support for RX and TX Pause frames individually. Signed-off-by:
Doug Berger <opendmb@gmail.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Doug Berger authored
This commit separates out the MAC configuration that occurs on a PHY state change into a function named bcmgenet_mac_config(). This allows the function to be called directly elsewhere. Signed-off-by:
-
Doug Berger authored
The PHY state machine has been fixed to only call the adjust_link callback when the link state has changed. Therefore the old link state variables are no longer needed to detect a change in link state. This commit effectively reverts commit 5ad6e6c5 ("net: bcmgenet: improve bcmgenet_mii_setup()") Signed-off-by:
-
Doug Berger authored
The bcmgenet_mii_setup() function is registered as the adjust_link callback from the phylib for the GENET driver. The phylib always sets the netif_carrier according to phydev->link prior to invoking the adjust_link callback, so there is no need to repeat that in the link down case within the network driver. Signed-off-by:
-
David S. Miller authored
Linus Walleij says: ==================== RTL8366(RB) cleanups part 1 This is a first set of patches making the RTL8366RB work out of the box with a default OpenWrt userspace. We achieve bridge port isolation with the first patch, and the next 5 patches removes the very weird VLAN set-up with one VLAN with PVID per port that has been in this driver in all vendor trees and in OpenWrt for years. The switch is now managed the way a modern bridge/DSA switch shall be managed. After these patches are merged, I will send the next set which adds new features, some which have circulated before. ChangeLog v4->v5: - Drop the patch disabling 4K VLAN. - Drop the patch forcing VLAN0 untagged. - Fix a semantic bug in the filer enablement code. ==================== Signed-off-by: -
Linus Walleij authored
We don't need a message for every VLAN association, dbg is fine. The message about adding the DSA or CPU port to a VLAN is directly misleading, this is perfectly fine. Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Mauri Sandberg <sandberg@mailfence.com> Cc: DENG Qingfang <dqfext@gmail.com> Reviewed-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
We were checking that the MC (member config) was != 0 for some reason, all we need to check is that the config has no ports, i.e. no members. Then it can be recycled. This must be some misunderstanding. Fixes: 4ddcaf1e ("net: dsa: rtl8366: Properly clear member config") Cc: Mauri Sandberg <sandberg@mailfence.com> Cc: DENG Qingfang <dqfext@gmail.com> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
-
Linus Walleij authored
The max VLAN number with non-4K VLAN activated is 15, and the range is 0..15. Not 16. The impact should be low since we by default have 4K VLAN and thus have 4095 VLANs to play with in this switch. There will not be a problem unless the code is rewritten to only use 16 VLANs. Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver") Cc: Mauri Sandberg <sandberg@mailfence.com> Cc: DENG Qingfang <dqfext@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Linus Walleij authored
While we were defining one VLAN per port for isolating the ports the port_vlan_filtering() callback was implemented to enable a VLAN on the port + 1. This function makes no sense, not only is it incomplete as it only enables the VLAN, it doesn't do what the callback is supposed to do, which is to selectively enable and disable filtering on a certain port. Implement the correct callback: we have two registers dealing with filtering on the RTL9366RB, so we implement an ASIC-specific callback and implement filering using the register bit that makes the switch drop frames if the port is not in the VLAN member set. The DSA documentation Documentation/networking/switchdev.rst states: When the bridge has VLAN filtering enabled and a PVID is not configured on the ingress port, untagged and 802.1p tagged packets must be dropped. When the bridge has VLAN filtering enabled and a PVID exists on the ingress port, untagged and priority-tagged packets must be accepted and forwarded according to the bridge's port membership of the PVID VLAN. When the bridge has VLAN filtering disabled, the presence/lack of a PVID should not influence the packet forwarding decision. To comply with this, we add two arrays of bool in the RTL8366RB state that keeps track of if filtering and PVID is enabled or not for each port. We then add code such that whenever filtering or PVID changes, we update the filter according to the specification. Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Mauri Sandberg <sandberg@mailfence.com> Cc: Alvin Šipraga <alsi@bang-olufsen.dk> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: DENG Qingfang <dqfext@gmail.com> Signed-off-by:
-
Linus Walleij authored
This hacky default VLAN setup was done in order to direct packets to the right ports and provide port isolation, both which we now support properly using custom tags and proper bridge port isolation. We can drop the custom VLAN code and leave all VLAN handling alone, as users expect things to be. We can also drop ds->configure_vlan_while_not_filtering = false; and let the core deal with any VLANs it wants. Cc: Mauri Sandberg <sandberg@mailfence.com> Cc: DENG Qingfang <dqfext@gmail.com> Reviewed-by:
-
DENG Qingfang authored
Use port isolation registers to configure bridge offloading. Tested on the D-Link DIR-685, switching between ports and sniffing ports to make sure no packets leak. Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Mauri Sandberg <sandberg@mailfence.com> Reviewed-by:
DENG Qingfang <dqfext@gmail.com> Signed-off-by:
-
