This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.

Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.

Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.

Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.

Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.

Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.

Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ieee802154 sockets do not properly unshare received skbs, which leads to
panics (at least) when they are used in conjunction with 6lowpan, so
run skb_share_check on received skbs.
6lowpan also contains a use-after-free, which is trivially fixed by
replacing the inlined skb_share_check with the explicit call.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

linux-can-next-for-3.15-20140317

Marc Kleine-Budde says:

====================
this is a pull request of three patches for net-next/master.

It consists of a patch by Oliver Hartkopp, which unifies the MTU
settings for CAN interfaces. A patch by Christopher R. Baker populates
netdev::dev_id for udev discrimination for multi interface CAN devices.
Alexander Shiyan contributes a patch for the mcp251x driver which fixes
the regulators operation if CONFIG_REGULATOR is not enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In generic, after an assignment, we use ';' instead of ','.
Although, it won't hurt.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since cd4d8fda ("net: kernel panic in dev_hard_start_xmit:
remove faulty software TX time stamping") dev_hard_start_xmit()
will not provide software timestamps. It's a responsibility of
the drivers to call skb_tx_timestamp() at the right time.

Cc: linux-doc@vger.kernel.org
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only ratelimit the ones that might spam, omiting the ones from
enslave/deslave.

CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit b4e9b520 ("[NET_SCHED]: Add mask support to fwmark
classifier") Patrick added an u32 field in fw_head, making it slightly
bigger than one page.

Lets use 256 slots to make fw_hash() more straight forward, and move
@mask to the beginning of the structure as we often use a small number
of skb->mark. @mask and first hash buckets share the same cache line.

This brings back the memory usage to less than 4000 bytes, and permits
John to add a rcu_head at the end of the structure later without any
worry.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
One patch to rename a newly introduced struct. The rest is
the rework of the IPsec virtual tunnel interface for ipv6 to
support inter address family tunneling and namespace crossing.

1) Rename the newly introduced struct xfrm_filter to avoid a
   conflict with iproute2. From Nicolas Dichtel.

2) Introduce xfrm_input_afinfo to access the address family
   dependent tunnel callback functions properly.

3) Add and use a IPsec protocol multiplexer for ipv6.

4) Remove dst_entry caching. vti can lookup multiple different
   dst entries, dependent of the configured xfrm states. Therefore
   it does not make to cache a dst_entry.

5) Remove caching of flow informations. vti6 does not use the the
   tunnel endpoint addresses to do route and xfrm lookups.

6) Update the vti6 to use its own receive hook.

7) Remove the now unused xfrm_tunnel_notifier. This was used from vti
   and is replaced by the IPsec protocol multiplexer hooks.

8) Support inter address family tunneling for vti6.

9) Check if the tunnel endpoints of the xfrm state and the vti interface
   are matching and return an error otherwise.

10) Enable namespace crossing for vti devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When compiling the i40e and the i40evf driver into the same kernel I get:
LD      drivers/net/ethernet/intel/built-in.o
drivers/net/ethernet/intel/i40evf/built-in.o:(.data+0x300): multiple definition of `i40e_ptype_lookup'
drivers/net/ethernet/intel/i40e/built-in.o:(.data+0x780): first defined here
make[3]: *** [drivers/net/ethernet/intel/built-in.o] Error 1
make[2]: *** [drivers/net/ethernet/intel] Error 2
make[1]: *** [drivers/net/ethernet/] Error 2
make: *** [sub-make] Error 2

Fix this by renaming the i40evf version of this structure from
i40e_ptype_lookup to i40evf_ptype_lookup.

This build failure was introduced in:
  commit 206812b5
  Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
  i40e/i40evf: i40e implementation for skb_set_hash

Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Eric W Biederman <ebiederm@xmission.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 28002099 (e1000e: Refactor PM flows) changed the
SET_SYSTEM_SLEEP_PM_OPS to open-coded assignment, but forgot to
protect them with CONFIG_PM_SLEEP. Then cause the following build
error when PM is disabled:
drivers/net/ethernet/intel/e1000e/netdev.c:7079:13:
error: 'e1000e_pm_suspend' undeclared here (not in a function)
  .suspend = e1000e_pm_suspend,
             ^
drivers/net/ethernet/intel/e1000e/netdev.c:7080:13:
error: 'e1000e_pm_resume' undeclared here (not in a function)
  .resume  = e1000e_pm_resume,
             ^
drivers/net/ethernet/intel/e1000e/netdev.c:7082:11:
error: 'e1000e_pm_thaw' undeclared here (not in a function)
  .thaw  = e1000e_pm_thaw,
           ^
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Command line parameters QueuePairs, Node, EEE, DMAC and InterruptThrottleRate
do not exist these days. Remove all references to them in the Documentation
folder and update code comments.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vince Bridgers says:

====================
Altera Triple Speed Ethernet (TSE) Driver

This is the version 6 submission for the Altera Triple Speed Ethernet (TSE)
driver. All comments received during the version 2, 3, 4, and 5 submissions
have been accepted. Please find the change log and a description of the
submission below.

If you find the submission acceptable, please consider this patch set for
inclusion into the Linux kernel.

V6: Address comments from V5 review
    - add call to skb_tx_timestamp in the drivers transmit path
    - correct use of unsigned int where it was cast to pointer. Use types
      appropriate for intended and correct use to let the compiler warn us
      when type usage is incorrect.
    - use correct semantics for pointer arithmetic in same code path

V5: Address comments from V4 review
    - Add descriptions of statistics to driver documentation. The statstics
      supported by the driver/controller map to IEEE and RFC statistics, and
      the names and mappings are described in the user documentation.
    - Change "unsigned int" to u32 in device structure definitions
    - Change used of netdev_warn to netif_warn in altera_sgdma.c
    - Change stat name rx_fifo_drops to ether_drops to match the event
      actually counted by the hardware.

V4: Address comments from V3 review
    - Change statistics names in ethtool module to follow common use in
      other ethernet drivers.
    - remove an unnecessary case in ethtool module
    - change logging to use netdev_* where possible instead of dev_*
    - remove logging for OOM errors since those are already logged

V3: Address comments from V2 review
    - Reorder patch submission so that net/ethernet Makefile and Kconfig
      are committed last, thus not breaking bisect
    - Use of_get_mac_address instead of of_get_property
    - Change supplemental and hash configuration bindings to boolean/empty,
      and more meaningful names
    - Add check for failure from calls to of_phy_connect and
      connect_local_phy
    - Correct code to find mdio child node
    - Update bindings document
    - Remove cast to u64 when not necessary
    - add use of const for statistics strings

V2: Address comments from initial RFC review.
    - The driver files were broken up by major sections of functionality.
      These include MSGDMA, SGDMA, Misc, and Main.
    - Add patch for MAINTAINERS file, add the maintainer for this submission
    - Use 32-bit lower/upper physical address accessor functions so the driver
      is 64-bit ready.
    - Use standard bindings where applicable. Especially phy-addr, and change
      "altr,rx-fifo-depth" to "rx-fifo-depth" and "altr,tx-fifo-depth" to
      "tx-fifo-depth".
    - Add use of max-frame-size property
    - Update bindings documents accordingly
    - Correct interrupt handler to use budget parameter in the convential way
    - Use macros consistently to define bit fields across files
    - Correct include exclusion macro in altera_msgdmahw.h (typo)
    - Remove use of barriers, these were not necessary since the DMA APIs
      ensure memory & buffer consistency
    - Remove use of netif_carrier_off in driver
    - move probing of phy from the open function to the probe function
    - use of_get_phy_mode instead of custom function
    - Use the .data field in the device structure to obtain a pointer
      to SGDMA or MSGDMA device specific properties and functions.
    - remove custom function to access devicetree since Altera specific
      bindings requiring it's use have been deprecated in favor of
      standard bindings.

The Altera TSE is a 10/100/1000 Mbps Ethernet soft IP component that can be
configured and synthesized using Quartus, and programmed into Altera FPGAs.
Two types of soft DMA IP components are supported by this driver - the Altera
SGDMA and the MSGDMA. The MSGDMA DMA component is preferred over the SGDMA,
since the SGDMA will be deprecated in favor of the MSGDMA. Software supporting
both is provided for customers still using the SGDMA and to demonstrate how
multiple types of DMA engines may be supported by the TSE driver in the event
customers wish to develop their own custom soft DMA engine for particular
applications.

The design has been tested on Altera's Cyclone 4, 5, and Cyclone 5 SOC
development kits using an ARM A9 processor and an Altera NIOS2 processor.
Differences in CPU/DMA coherency management and address alignment are
addressed by proper use of driver APIs and semantics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch changes the Ethernet Makefile and Kconfig files to add the Altera
Ethernet driver component.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a MAINTAINERS entry covering the Altera Triple Speed
Ethernet Driver, with support for the MSGDMA and SGDMA
soft DMA IP components.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the Altera Triple Speed Ethernet Makfile and
Kconfig file.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the main driver and header file for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds miscellaneous files for the Altera Ethernet Driver,
including ethtool support.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the SGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the MSGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a bindings description for the Altera Triple Speed Ethernet
(TSE) driver. The bindings support the legacy SGDMA soft IP as well as the
preferred MSGDMA soft IP. The TSE can be configured and synthesized in soft
logic using Altera's Quartus toolchain. Please consult the bindings document
for supported options.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a bindings description for the Altera Triple Speed Ethernet
(TSE) driver. The bindings support the legacy SGDMA soft IP as well as the
preferred MSGDMA soft IP. The TSE can be configured and synthesized in soft
logic using Altera's Quartus toolchain. Please consult the bindings document
for supported options.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARRAY_SIZE(nf_conntrack_locks) is undefined if spinlock_t is an
empty structure. Replace it by CONNTRACK_LOCKS

Fixes: 93bb0ceb ("netfilter: conntrack: remove central spinlock nf_conntrack_lock")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
at86rf230: various fixes and devicetree support

this patch series fix some bugs with the at86rf231 chip and cleaup some code.
Also add devicetree support for the at86rf230 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds devicetree support for the at86rf230 driver.

Possible gpios to configure are "reset-gpio" and "sleep-gpio".
Also add support to configure the "irq-type" for the irq polarity
register.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch make the reset pin optionally. Some devices like the atben
from qi-hardware don't have a reset pin externally. The usually way is
to turn power off/on for the atben device to initiate a device reset.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While checkpatch another patch I got a:

"WARNING: msleep < 20ms can sleep for up to 20ms"

The datasheet of at86rf231 and at86rf212 says a minimum delay for reset
pulse width and spi access latency after reset is 625 nanoseconds.

This patch removes the 1 milliseconds sleep and replace it with a 1
microseconds udelay which should be also okay for the reset pulse width.

To change the state from RESET -> TRX_OFF the at86rf230 device needs 120
microseconds, this is a worst case of all at86rf* chips.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to lock the clearing of IRQ_TRX_END in status.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix a unexpected state change for the at86rf231 chip.
We can't change into STATE_FORCE_TX_ON while the chip is in one of
SLEEP, P_ON, RESET, TRX_OFF, and all *_NOCLK states.

In this case we are in the TRX_OFF state. See datasheet [1] page 71 for
more information.

Without this patch you will get the following message on a at86rf231 device:

[   20.065218] unexpected state change: 8, asked for 4
[   20.070527] ------------[ cut here ]------------
[   20.075414] WARNING: CPU: 0 PID: 160 at net/mac802154/ieee802154_dev.c:43 mac802154_slave_open+0x70/0xb8()
[   20.085594] Modules linked in: autofs4
[   20.089667] CPU: 0 PID: 160 Comm: ifconfig Not tainted 3.14.0-20140108-1-00993-g905c192 #162
[   20.098612] [<c00127b8>] (unwind_backtrace) from [<c0010b1c>] (show_stack+0x10/0x14)
[   20.106819] [<c0010b1c>] (show_stack) from [<c0033838>] (warn_slowpath_common+0x60/0x80)
[   20.115311] [<c0033838>] (warn_slowpath_common) from [<c00338e8>] (warn_slowpath_null+0x18/0x20)
[   20.124590] [<c00338e8>] (warn_slowpath_null) from [<c057b7e8>] (mac802154_slave_open+0x70/0xb8)
[   20.133880] [<c057b7e8>] (mac802154_slave_open) from [<c0488a58>] (__dev_open+0xa8/0x108)
[   20.142553] [<c0488a58>] (__dev_open) from [<c0488cb0>] (__dev_change_flags+0x8c/0x148)
[   20.151051] [<c0488cb0>] (__dev_change_flags) from [<c0488d84>] (dev_change_flags+0x18/0x48)
[   20.159968] [<c0488d84>] (dev_change_flags) from [<c04e2e9c>] (devinet_ioctl+0x2b0/0x63c)
[   20.168623] [<c04e2e9c>] (devinet_ioctl) from [<c04712e4>] (sock_ioctl+0x23c/0x29c)
[   20.176727] [<c04712e4>] (sock_ioctl) from [<c00e3cb8>] (do_vfs_ioctl+0x4a8/0x578)
[   20.184671] [<c00e3cb8>] (do_vfs_ioctl) from [<c00e3dd4>] (SyS_ioctl+0x4c/0x78)
[   20.192402] [<c00e3dd4>] (SyS_ioctl) from [<c000da00>] (ret_fast_syscall+0x0/0x48)
[   20.200392] ---[ end trace 9a34542f4ea08e47 ]---

This patch was tested on at86rf231 and at86rf212.

[1] http://www.atmel.com/images/doc8111.pdfSigned-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
Beautify 'sh_eth' driver's messages

This patchset converts te driver to using netdev_*() and netif_*() to print out
its messages whenever possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we call netdev_*() under netif_msg_*() checks, we can fold these into
netif_*() macro invocations.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert dev_*(&ndev->dev, ...) to netdev_*(ndev, ...) calls since they are a bit
shorter and at the same time give more information on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert pr_*() to netdev_*() calls as the latter provide info on a device.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Exit the driver's probe() method when the register layout is unknown as the
driver would cause kernel oops in this case anyway.

While at it, move the corresponding error message printout and convert it from
pr_err() to dev_err().
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric W. Biederman says:

====================
netpoll: Cleanup received packet processing

This is the long-winded, careful, and polite version of removing the netpoll
receive packet processing.

First I untangle the code in small steps.  Then I modify the code to not
force reception and dropping of packets when we are transmiting a packet
with netpoll.  Finally I move all of the packet reception under
CONFIG_NETPOLL_TRAP and delete CONFIG_NETPOLL_TRAP.

If someone wants to do a stable backport of these patches, it would
require backporting the first 18 patches that handle the budget == 0 in
the networking drivers, and the first 6 of these patches.

If anyone wants to resurrect netpoll packet reception someday it should
just be a matter of reverting the last patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.

All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.

There are problems with the netpoll packet receive code.  __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context.  netpoll_neigh_reply leaks every skb it receives.  Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).

Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.

Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>