- 09 Jan, 2019 40 commits
-
-
Lukas Wunner authored
commit 56c17234 upstream. The IRQ handler bcm2835_spi_interrupt() first reads as much as possible from the RX FIFO, then writes as much as possible to the TX FIFO. Afterwards it decides whether the transfer is finished by checking if the TX FIFO is empty. If very few bytes were written to the TX FIFO, they may already have been transmitted by the time the FIFO's emptiness is checked. As a result, the transfer will be declared finished and the chip will be reset without reading the corresponding received bytes from the RX FIFO. The odds of this happening increase with a high clock frequency (such that the TX FIFO drains quickly) and either passing "threadirqs" on the command line or enabling CONFIG_PREEMPT_RT_BASE (such that the IRQ handler may be preempted between filling the TX FIFO and checking its emptiness). Fix by instead checking whether rx_len has reached zero, which means that the transfer has been received in full. This is also more efficient as it avoids one bus read access per interrupt. Note that bcm2835_spi_transfer_one_poll() likewise uses rx_len to determine whether the transfer has finished. Signed-off-by:
Lukas Wunner <lukas@wunner.de> Fixes: e34ff011 ("spi: bcm2835: move to the transfer_one driver model") Cc: stable@vger.kernel.org # v4.1+ Cc: Mathias Duckeck <m.duckeck@kunbus.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Martin Sperl <kernel@martin.sperl.org> Cc: Noralf Trønnes <noralf@tronnes.org> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lukas Wunner authored
commit dbc94411 upstream. If submission of a DMA TX transfer succeeds but submission of the corresponding RX transfer does not, the BCM2835 SPI driver terminates the TX transfer but neglects to reset the dma_pending flag to false. Thus, if the next transfer uses interrupt mode (because it is shorter than BCM2835_SPI_DMA_MIN_LENGTH) and runs into a timeout, dmaengine_terminate_all() will be called both for TX (once more) and for RX (which was never started in the first place). Fix it. Signed-off-by:
-
Lukas Wunner authored
commit e82b0b38 upstream. If a DMA transfer finishes orderly right when spi_transfer_one_message() determines that it has timed out, the callbacks bcm2835_spi_dma_done() and bcm2835_spi_handle_err() race to call dmaengine_terminate_all(), potentially leading to double termination. Prevent by atomically changing the dma_pending flag before calling dmaengine_terminate_all(). Signed-off-by:
-
Theodore Ts'o authored
commit 18f2c4fc upstream. If the file system has been shut down or is read-only, then ext4_write_inode() needs to bail out early. Also use jbd2_complete_transaction() instead of ext4_force_commit() so we only force a commit if it is needed. Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by:
-
Theodore Ts'o authored
commit fde87268 upstream. Some time back, nfsd switched from calling vfs_fsync() to using a new commit_metadata() hook in export_operations(). If the file system did not provide a commit_metadata() hook, it fell back to using sync_inode_metadata(). Unfortunately doesn't work on all file systems. In particular, it doesn't work on ext4 due to how the inode gets journalled --- the VFS writeback code will not always call ext4_write_inode(). So we need to provide our own ext4_nfs_commit_metdata() method which calls ext4_write_inode() directly. Google-Bug-Id: 121195940 Signed-off-by:
-
Theodore Ts'o authored
commit a805622a upstream. In ext4_expand_extra_isize_ea(), we calculate the total size of the xattr header, plus the xattr entries so we know how much of the beginning part of the xattrs to move when expanding the inode extra size. We need to include the terminating u32 at the end of the xattr entries, or else if there is uninitialized, non-zero bytes after the xattr entries and before the xattr values, the list of xattr entries won't be properly terminated. Reported-by:
Steve Graham <stgraham2000@gmail.com> Signed-off-by:
-
ruippan (潘睿) authored
commit e647e291 upstream. Commit e2b911c5 ("ext4: clean up feature test macros with predicate functions") broke the EXT4_IOC_GROUP_ADD ioctl. This was not noticed since only very old versions of resize2fs (before e2fsprogs 1.42) use this ioctl. However, using a new kernel with an enterprise Linux userspace will cause attempts to use online resize to fail with "No reserved GDT blocks". Fixes: e2b911c5 ("ext4: clean up feature test macros with predicate...") Cc: stable@kernel.org # v4.4 Signed-off-by:
ruippan (潘睿) <ruippan@tencent.com> Signed-off-by:
-
Maurizio Lombardi authored
commit 132d00be upstream. In case of error, ext4_try_to_write_inline_data() should unlock and release the page it holds. Fixes: f19d5870 ("ext4: add normal write support for inline data") Cc: stable@kernel.org # 3.8 Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Signed-off-by:
-
Pan Bian authored
commit 61157b24 upstream. The function frees qf_inode via iput but then pass qf_inode to lockdep_set_quota_inode on the failure path. This may result in a use-after-free bug. The patch frees df_inode only when it is never used. Fixes: daf647d2 ("ext4: add lockdep annotations for i_data_sem") Cc: stable@kernel.org # 4.6 Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Pan Bian <bianpan2016@163.com> Signed-off-by:
-
Theodore Ts'o authored
commit fb265c9c upstream. Today, when sb_bread() returns NULL, this can either be because of an I/O error or because the system failed to allocate the buffer. Since it's an old interface, changing would require changing many call sites. So instead we create our own ext4_sb_bread(), which also allows us to set the REQ_META flag. Also fixed a problem in the xattr code where a NULL return in a function could also mean that the xattr was not found, which could lead to the wrong error getting returned to userspace. Fixes: ac27a0ec ("ext4: initial copy of files from ext3") Cc: stable@kernel.org # 2.6.19 Signed-off-by:
-
Ben Hutchings authored
commit 11a64a05 upstream. Depending on which functions are inlined in util/pmu.c, the snprintf() calls in perf_pmu__parse_{scale,unit,per_pkg,snapshot}() might trigger a warning: util/pmu.c: In function 'pmu_aliases': util/pmu.c:178:31: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 4095 [-Werror=format-truncation=] snprintf(path, PATH_MAX, "%s/%s.unit", dir, name); ^~ I found this when trying to build perf from Linux 3.16 with gcc 8. However I can reproduce the problem in mainline if I force __perf_pmu__new_alias() to be inlined. Suppress this by using scnprintf() as has been done elsewhere in perf. Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20181111184524.fux4taownc6ndbx6@decadent.org.ukSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Miquel Raynal authored
commit 81b1e6e6 upstream. Since the addition of platform MSI support, there were two helpers supposed to allocate/free IRQs for a device: platform_msi_domain_alloc_irqs() platform_msi_domain_free_irqs() In these helpers, IRQ descriptors are allocated in the "alloc" routine while they are freed in the "free" one. Later, two other helpers have been added to handle IRQ domains on top of MSI domains: platform_msi_domain_alloc() platform_msi_domain_free() Seen from the outside, the logic is pretty close with the former helpers and people used it with the same logic as before: a platform_msi_domain_alloc() call should be balanced with a platform_msi_domain_free() call. While this is probably what was intended to do, the platform_msi_domain_free() does not remove/free the IRQ descriptor(s) created/inserted in platform_msi_domain_alloc(). One effect of such situation is that removing a module that requested an IRQ will let one orphaned IRQ descriptor (with an allocated MSI entry) in the device descriptors list. Next time the module will be inserted back, one will observe that the allocation will happen twice in the MSI domain, one time for the remaining descriptor, one time for the new one. It also has the side effect to quickly overshoot the maximum number of allocated MSI and then prevent any module requesting an interrupt in the same domain to be inserted anymore. This situation has been met with loops of insertion/removal of the mvpp2.ko module (requesting 15 MSIs each time). Fixes: 552c494a ("platform-msi: Allow creation of a MSI-based stacked irq domain") Cc: stable@vger.kernel.org Signed-off-by:
Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Sean Christopherson authored
commit 1b3ab5ad upstream. Fixes: 34a1cd60 ("kvm: x86: vmx: move some vmx setting from vmx_init() to hardware_setup()") Cc: stable@vger.kernel.org Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Sean Christopherson authored
commit e8143499 upstream. ____kvm_handle_fault_on_reboot() provides a generic exception fixup handler that is used to cleanly handle faults on VMX/SVM instructions during reboot (or at least try to). If there isn't a reboot in progress, ____kvm_handle_fault_on_reboot() treats any exception as fatal to KVM and invokes kvm_spurious_fault(), which in turn generates a BUG() to get a stack trace and die. When it was originally added by commit 4ecac3fd ("KVM: Handle virtualization instruction #UD faults during reboot"), the "call" to kvm_spurious_fault() was handcoded as PUSH+JMP, where the PUSH'd value is the RIP of the faulting instructing. The PUSH+JMP trickery is necessary because the exception fixup handler code lies outside of its associated function, e.g. right after the function. An actual CALL from the .fixup code would show a slightly bogus stack trace, e.g. an extra "random" function would be inserted into the trace, as the return RIP on the stack would point to no known function (and the unwinder will likely try to guess who owns the RIP). Unfortunately, the JMP was replaced with a CALL when the macro was reworked to not spin indefinitely during reboot (commit b7c4145b "KVM: Don't spin on virt instruction faults during reboot"). This causes the aforementioned behavior where a bogus function is inserted into the stack trace, e.g. my builds like to blame free_kvm_area(). Revert the CALL back to a JMP. The changelog for commit b7c4145b ("KVM: Don't spin on virt instruction faults during reboot") contains nothing that indicates the switch to CALL was deliberate. This is backed up by the fact that the PUSH <insn RIP> was left intact. Note that an alternative to the PUSH+JMP magic would be to JMP back to the "real" code and CALL from there, but that would require adding a JMP in the non-faulting path to avoid calling kvm_spurious_fault() and would add no value, i.e. the stack trace would be the same. Using CALL: ------------[ cut here ]------------ kernel BUG at /home/sean/go/src/kernel.org/linux/arch/x86/kvm/x86.c:356! invalid opcode: 0000 [#1] SMP CPU: 4 PID: 1057 Comm: qemu-system-x86 Not tainted 4.20.0-rc6+ #75 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:kvm_spurious_fault+0x5/0x10 [kvm] Code: <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 49 89 fd 41 RSP: 0018:ffffc900004bbcc8 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffffffffff RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff888273fd8000 R08: 00000000000003e8 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000784 R12: ffffc90000371fb0 R13: 0000000000000000 R14: 000000026d763cf4 R15: ffff888273fd8000 FS: 00007f3d69691700(0000) GS:ffff888277800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055f89bc56fe0 CR3: 0000000271a5a001 CR4: 0000000000362ee0 Call Trace: free_kvm_area+0x1044/0x43ea [kvm_intel] ? vmx_vcpu_run+0x156/0x630 [kvm_intel] ? kvm_arch_vcpu_ioctl_run+0x447/0x1a40 [kvm] ? kvm_vcpu_ioctl+0x368/0x5c0 [kvm] ? kvm_vcpu_ioctl+0x368/0x5c0 [kvm] ? __set_task_blocked+0x38/0x90 ? __set_current_blocked+0x50/0x60 ? __fpu__restore_sig+0x97/0x490 ? do_vfs_ioctl+0xa1/0x620 ? __x64_sys_futex+0x89/0x180 ? ksys_ioctl+0x66/0x70 ? __x64_sys_ioctl+0x16/0x20 ? do_syscall_64+0x4f/0x100 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 Modules linked in: vhost_net vhost tap kvm_intel kvm irqbypass bridge stp llc ---[ end trace 9775b14b123b1713 ]--- Using JMP: ------------[ cut here ]------------ kernel BUG at /home/sean/go/src/kernel.org/linux/arch/x86/kvm/x86.c:356! invalid opcode: 0000 [#1] SMP CPU: 6 PID: 1067 Comm: qemu-system-x86 Not tainted 4.20.0-rc6+ #75 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:kvm_spurious_fault+0x5/0x10 [kvm] Code: <0f> 0b 66 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 41 55 49 89 fd 41 RSP: 0018:ffffc90000497cd0 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffffffffffff RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000 RBP: ffff88827058bd40 R08: 00000000000003e8 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000784 R12: ffffc90000369fb0 R13: 0000000000000000 R14: 00000003c8fc6642 R15: ffff88827058bd40 FS: 00007f3d7219e700(0000) GS:ffff888277900000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f3d64001000 CR3: 0000000271c6b004 CR4: 0000000000362ee0 Call Trace: vmx_vcpu_run+0x156/0x630 [kvm_intel] ? kvm_arch_vcpu_ioctl_run+0x447/0x1a40 [kvm] ? kvm_vcpu_ioctl+0x368/0x5c0 [kvm] ? kvm_vcpu_ioctl+0x368/0x5c0 [kvm] ? __set_task_blocked+0x38/0x90 ? __set_current_blocked+0x50/0x60 ? __fpu__restore_sig+0x97/0x490 ? do_vfs_ioctl+0xa1/0x620 ? __x64_sys_futex+0x89/0x180 ? ksys_ioctl+0x66/0x70 ? __x64_sys_ioctl+0x16/0x20 ? do_syscall_64+0x4f/0x100 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 Modules linked in: vhost_net vhost tap kvm_intel kvm irqbypass bridge stp llc ---[ end trace f9daedb85ab3ddba ]--- Fixes: b7c4145b ("KVM: Don't spin on virt instruction faults during reboot") Cc: stable@vger.kernel.org Signed-off-by:
-
Dan Williams authored
commit ba6f508d upstream. Commit: f77084d9 "x86/mm/pat: Disable preemption around __flush_tlb_all()" addressed a case where __flush_tlb_all() is called without preemption being disabled. It also left a warning to catch other cases where preemption is not disabled. That warning triggers for the memory hotplug path which is also used for persistent memory enabling: WARNING: CPU: 35 PID: 911 at ./arch/x86/include/asm/tlbflush.h:460 RIP: 0010:__flush_tlb_all+0x1b/0x3a [..] Call Trace: phys_pud_init+0x29c/0x2bb kernel_physical_mapping_init+0xfc/0x219 init_memory_mapping+0x1a5/0x3b0 arch_add_memory+0x2c/0x50 devm_memremap_pages+0x3aa/0x610 pmem_attach_disk+0x585/0x700 [nd_pmem] Andy wondered why a path that can sleep was using __flush_tlb_all() [1] and Dave confirmed the expectation for TLB flush is for modifying / invalidating existing PTE entries, but not initial population [2]. Drop the usage of __flush_tlb_all() in phys_{p4d,pud,pmd}_init() on the expectation that this path is only ever populating empty entries for the linear map. Note, at linear map teardown time there is a call to the all-cpu flush_tlb_all() to invalidate the removed mappings. [1]: https://lkml.kernel.org/r/9DFD717D-857D-493D-A606-B635D72BAC21@amacapital.net [2]: https://lkml.kernel.org/r/749919a4-cdb1-48a3-adb4-adb81a5fa0b5@intel.com [ mingo: Minor readability edits. ] Suggested-by:
Dave Hansen <dave.hansen@linux.intel.com> Reported-by:
Andy Lutomirski <luto@kernel.org> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: <stable@vger.kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@surriel.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dave.hansen@intel.com Fixes: f77084d9 ("x86/mm/pat: Disable preemption around __flush_tlb_all()") Link: http://lkml.kernel.org/r/154395944713.32119.15611079023837132638.stgit@dwillia2-desk3.amr.corp.intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Michal Hocko authored
commit 5b5e4d62 upstream. Swap storage is restricted to max_swapfile_size (~16TB on x86_64) whenever the system is deemed affected by L1TF vulnerability. Even though the limit is quite high for most deployments it seems to be too restrictive for deployments which are willing to live with the mitigation disabled. We have a customer to deploy 8x 6,4TB PCIe/NVMe SSD swap devices which is clearly out of the limit. Drop the swap restriction when l1tf=off is specified. It also doesn't make much sense to warn about too much memory for the l1tf mitigation when it is forcefully disabled by the administrator. [ tglx: Folded the documentation delta change ] Fixes: 377eeaa8 ("x86/speculation/l1tf: Limit swap file size to MAX_PA/2") Signed-off-by:
Michal Hocko <mhocko@suse.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Pavel Tatashin <pasha.tatashin@soleen.com> Reviewed-by:
Andi Kleen <ak@linux.intel.com> Acked-by:
Jiri Kosina <jkosina@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: <linux-mm@kvack.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20181113184910.26697-1-mhocko@kernel.orgSigned-off-by:
-
Patrick Dreyer authored
commit 7db54c89 upstream. This adds ELAN0501 to the ACPI table to support Elan touchpad found in ASUS Aspire F5-573G. Signed-off-by:
Patrick Dreyer <Patrick.Dreyer@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Sebastian Ott authored
commit 98dfd326 upstream. When triggered by pci hotplug (PEC 0x306) clp_get_state is called with spinlocks held resulting in the following warning: zpci: n/a: Event 0x306 reconfigured PCI function 0x0 BUG: sleeping function called from invalid context at mm/page_alloc.c:4324 in_atomic(): 1, irqs_disabled(): 0, pid: 98, name: kmcheck 2 locks held by kmcheck/98: Change the allocation to use GFP_ATOMIC. Cc: stable@vger.kernel.org # 4.13+ Signed-off-by:
Sebastian Ott <sebott@linux.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Bjørn Mork authored
commit 102cd909 upstream. SIMCOM are reusing a single device ID for many (all of their?) different modems, based on different chipsets and firmwares. Newer Qualcomm chipset generations require setting DTR to wake the QMI function. The SIM7600E modem is using such a chipset, making it fail to work with this driver despite the device ID match. Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM modems using this specific device ID. This is similar to what we already have done for another case of device IDs recycled over multiple chipset generations: 14cf4a77 ("drivers: net: usb: qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201") Initial testing on an older SIM7100 modem shows no immediate side effects. Reported-by:
Sebastian Sjoholm <sebastian.sjoholm@gmail.com> Cc: Reinhard Speyerer <rspmn@arcor.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Colin Ian King authored
commit c58eef06 upstream. Currently the cmd.read_write setting is not initialized so it contains garbage from the stack. Fix this by setting it to 0 to indicate a read is required. Detected by CoverityScan, CID#1357925 ("Uninitialized scalar variable") Fixes: c5c77ba1 ("staging: wilc1000: Add SDIO/SPI 802.11 driver") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Ajay Singh <ajay.kathat@microchip.com> Signed-off-by:
-
Jia-Ju Bai authored
commit c85400f8 upstream. The function r8a66597_endpoint_disable() and r8a66597_urb_enqueue() may be concurrently executed. The two functions both access a possible shared variable "hep->hcpriv". This shared variable is freed by r8a66597_endpoint_disable() via the call path: r8a66597_endpoint_disable kfree(hep->hcpriv) (line 1995 in Linux-4.19) This variable is read by r8a66597_urb_enqueue() via the call path: r8a66597_urb_enqueue spin_lock_irqsave(&r8a66597->lock) init_pipe_info enable_r8a66597_pipe pipe = hep->hcpriv (line 802 in Linux-4.19) The read operation is protected by a spinlock, but the free operation is not protected by this spinlock, thus a concurrency use-after-free bug may occur. To fix this bug, the spin-lock and spin-unlock function calls in r8a66597_endpoint_disable() are moved to protect the free operation. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Jörgen Storvist authored
commit 4b2c01ad upstream. Added USB serial option driver support for Fibocom NL678 series cellular module: VID 2cb7 and PIDs 0x0104 and 0x0105. Reserved network and ADB interfaces. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=0104 Rev=03.10 S: Manufacturer=Fibocom S: Product=Fibocom NL678-E Modem S: SerialNumber=12345678 C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=0105 Rev=03.10 S: Manufacturer=Fibocom S: Product=Fibocom NL678-E Modem S: SerialNumber=12345678 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) Signed-off-by:
Jörgen Storvist <jorgen.storvist@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Scott Chen authored
commit 8d503f20 upstream. Add device ids to pl2303 for the HP POS pole displays: LM920: 03f0:026b TD620: 03f0:0956 LD960TA: 03f0:4439 LD220TA: 03f0:4349 LM940: 03f0:5039 Signed-off-by:
Scott Chen <scott@labau.com.tw> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Sameer Pujar authored
commit 63d2a9ec upstream. Even after disabling interrupts on the module, it could be possible that irq handlers are still running. System hang is seen during suspend path. It was found that, there were pending writes on the HDA bus and clock was disabled by that time. Above mentioned issue is fixed by clearing any pending irq handlers before disabling clocks and returning from hda suspend. Suggested-by:
Mohan Kumar <mkumard@nvidia.com> Suggested-by:
Dara Ramesh <dramesh@nvidia.com> Signed-off-by:
Sameer Pujar <spujar@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Sakamoto authored
commit 5ef108c5 upstream. An initial commit to add tracepoints for packets without CIP headers uses different print formats for added tracepoints. However this is not convenient for users/developers to prepare debug tools. This commit uses the same format for the two tracepoints. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: b164d2fd ('ALSA: firewire_lib: add tracepoints for packets without CIP headers') Signed-off-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
-
Takashi Sakamoto authored
commit aa9a9e39 upstream. An initial commit to add tracepoints for packets without CIP headers introduces a wrong assignment to 'data_blocks' value of 'out_packet_without_header' tracepoint. This commit fixes the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: b164d2fd ('ALSA: firewire_lib: add tracepoints for packets without CIP headers') Signed-off-by:
-
Takashi Sakamoto authored
commit ada79fa5 upstream. In IEC 61883-1/6 engine of ALSA firewire stack, a packet handler has a second argument for 'the number of bytes in payload of isochronous packet'. However, an incoming packet handler without CIP header uses the value as 'the number of quadlets in the payload'. This brings userspace applications to receive the number of PCM frames as four times against real time. This commit fixes the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: 3b196c39 ('ALSA: firewire-lib: add no-header packet processing') Signed-off-by:
-
Takashi Sakamoto authored
commit 3d16200a upstream. According to my memo at hand and saved records, writing 0x00000001 to SND_FF_REG_FETCH_PCM_FRAMES disables fetching PCM frames in corresponding channel, however current implement uses reversed logic. This results in muted volume in device side during playback. This commit corrects the bug. Cc: <stable@vger.kernel.org> # v4.12+ Fixes: 76fdb3a9 ('ALSA: fireface: add support for Fireface 400') Signed-off-by:
-
Mantas Mikulėnas authored
commit 40906ebe upstream. Tested with 4.19.9. v2: Changed from CXT_FIXUP_MUTE_LED_GPIO to CXT_FIXUP_HP_DOCK because that's what the existing fixups for EliteBooks use. Signed-off-by:
Mantas Mikulėnas <grawity@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Arnd Bergmann authored
commit 2a9d92fb upstream. I ran into a link-time error with the atmel-quadspi driver on the EBSA110 platform: drivers/mtd/built-in.o: In function `atmel_qspi_run_command': :(.text+0x1ee3c): undefined reference to `_memcpy_toio' :(.text+0x1ee48): undefined reference to `_memcpy_fromio' The problem is that _memcpy_toio/_memcpy_fromio are not available on that platform, and we have to prevent building the driver there. In case we want to backport this to older kernels: between linux-4.8 and linux-4.20, the Kconfig entry was in drivers/mtd/spi-nor/Kconfig but had the same problem. Link: https://lore.kernel.org/patchwork/patch/812860/ Fixes: 161aaab8 ("mtd: atmel-quadspi: add driver for Atmel QSPI controller") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by:
-
Gustavo A. R. Silva authored
commit 4aea96f4 upstream. info.mode and info.port are indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. These issues were detected with the help of Smatch: sound/synth/emux/emux_hwdep.c:72 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[i]->ctrls' [w] (local cap) sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs' [w] (local cap) sound/synth/emux/emux_hwdep.c:75 snd_emux_hwdep_misc_mode() warn: potential spectre issue 'emu->portptrs[info.port]->ctrls' [w] (local cap) Fix this by sanitizing both info.mode and info.port before using them to index emu->portptrs[i]->ctrls, emu->portptrs[info.port]->ctrls and emu->portptrs. Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Gustavo A. R. Silva authored
commit 94ffb030 upstream. stream is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: sound/core/pcm.c:140 snd_pcm_control_ioctl() warn: potential spectre issue 'pcm->streams' [r] (local cap) Fix this by sanitizing stream before using it to index pcm->streams Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2Signed-off-by:
-
Gustavo A. R. Silva authored
commit 5ae4f61f upstream. ipcm->substream is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: sound/pci/emu10k1/emufx.c:1031 snd_emu10k1_ipcm_poke() warn: potential spectre issue 'emu->fx8010.pcm' [r] (local cap) sound/pci/emu10k1/emufx.c:1075 snd_emu10k1_ipcm_peek() warn: potential spectre issue 'emu->fx8010.pcm' [r] (local cap) Fix this by sanitizing ipcm->substream before using it to index emu->fx8010.pcm Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
-
Gustavo A. R. Silva authored
commit 0b84304e upstream. info->channel is indirectly controlled by user-space, hence leading to a potential exploitation of the Spectre variant 1 vulnerability. This issue was detected with the help of Smatch: sound/pci/rme9652/hdsp.c:4100 snd_hdsp_channel_info() warn: potential spectre issue 'hdsp->channel_map' [r] (local cap) Fix this by sanitizing info->channel before using it to index hdsp->channel_map Notice that given that speculation windows are large, the policy is to kill the speculation on the first load and not worry if it can be completed with a dependent load/store [1]. Also, notice that I refactored the code a bit in order to get rid of the following checkpatch warning: ERROR: do not use assignment in if condition FILE: sound/pci/rme9652/hdsp.c:4103: if ((mapped_channel = hdsp->channel_map[info->channel]) < 0) [1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2 Cc: stable@vger.kernel.org Signed-off-by:
-
Michael J. Ruhl authored
commit dbc2970c upstream. An incorrect sge sizing in the HFI PIO path will cause an OOPs similar to this: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [] hfi1_verbs_send_pio+0x3d8/0x530 [hfi1] PGD 0 Oops: 0000 1 SMP Call Trace: ? hfi1_verbs_send_dma+0xad0/0xad0 [hfi1] hfi1_verbs_send+0xdf/0x250 [hfi1] ? make_rc_ack+0xa80/0xa80 [hfi1] hfi1_do_send+0x192/0x430 [hfi1] hfi1_do_send_from_rvt+0x10/0x20 [hfi1] rvt_post_send+0x369/0x820 [rdmavt] ib_uverbs_post_send+0x317/0x570 [ib_uverbs] ib_uverbs_write+0x26f/0x420 [ib_uverbs] ? security_file_permission+0x21/0xa0 vfs_write+0xbd/0x1e0 ? mntput+0x24/0x40 SyS_write+0x7f/0xe0 system_call_fastpath+0x16/0x1b Fix by adding the missing sizing check to correctly determine the sge length. Fixes: 77241056 ("IB/hfi1: add driver files") Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Deepa Dinamani authored
[ Upstream commit 3a0ed3e9 ] Al Viro mentioned (Message-ID <20170626041334.GZ10672@ZenIV.linux.org.uk>) that there is probably a race condition lurking in accesses of sk_stamp on 32-bit machines. sock->sk_stamp is of type ktime_t which is always an s64. On a 32 bit architecture, we might run into situations of unsafe access as the access to the field becomes non atomic. Use seqlocks for synchronization. This allows us to avoid using spinlocks for readers as readers do not need mutual exclusion. Another approach to solve this is to require sk_lock for all modifications of the timestamps. The current approach allows for timestamps to have their own lock: sk_stamp_lock. This allows for the patch to not compete with already existing critical sections, and side effects are limited to the paths in the patch. The addition of the new field maintains the data locality optimizations from commit 9115e8cd ("net: reorganize struct sock for better data locality") Note that all the instances of the sk_stamp accesses are either through the ioctl or the syscall recvmsg. Signed-off-by:
Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by:
-
Myungho Jung authored
[ Upstream commit 78abe3d0 ] clcsock can be released while kernel_accept() references it in TCP listen worker. Also, clcsock needs to wake up before released if TCP fallback is used and the clcsock is blocked by accept. Add a lock to safely release clcsock and call kernel_sock_shutdown() to wake up clcsock from accept in smc_release(). Reported-by: syzbot+0bf2e01269f1274b4b03@syzkaller.appspotmail.com Reported-by: syzbot+e3132895630f957306bc@syzkaller.appspotmail.com Signed-off-by:
Myungho Jung <mhjungk@gmail.com> Signed-off-by:
-
Jörgen Storvist authored
[ Upstream commit 7c3db410 ] Added support for Fibocom NL678 series cellular module QMI interface. Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x40 series chipsets. Signed-off-by:
-
Jörgen Storvist authored
[ Upstream commit 110a1cc2 ] Added support for Fibocom NL668 series QMI interface. Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets. Signed-off-by:
-
Cong Wang authored
[ Upstream commit fb83ed49 ] When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely based on the protocol in local address. We should just error out when the remote address and local address have different protocols. Reported-by: syzbot+eb4da3a20fad2e52555d@syzkaller.appspotmail.com Cc: Ying Xue <ying.xue@windriver.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
