net/mlx5: Expose MPFS configuration API

MPFS is the multi physical function switch that bridges traffic between
the physical port and any physical functions associated with it. The
driver is required to add or remove MAC entries to properly forward
incoming traffic to the correct physical function.

We export the API to control MPFS so that other drivers, such as
mlx5_vdpa are able to add MAC addresses of their network interfaces.

The MAC address of the vdpa interface must be configured into the MPFS L2
address. Failing to do so could cause, in some NIC configurations, failure
to forward packets to the vdpa network device instance.

Fix this by adding calls to update the MPFS table.

CC: <mst@redhat.com>
CC: <jasowang@redhat.com>
CC: <virtualization@lists.linux-foundation.org>
Fixes: 1a86b377 ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Avoid division by zero in the error flow. In the driver TC number can be
either 1 or 8. When TC count is set to 1, driver zero netdev->num_tc.
Hence, need to convert it back from 0 to 1 in the error flow.

Fixes: fa374877 ("net/mlx5e: Handle errors from netif_set_real_num_{tx,rx}_queues")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Rules with MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE dest flag are
translated to destination FT in eswitch. Currently it is not possible to
mirror such rules because firmware doesn't support mixing FT and Vport
destinations in single rule when one of them adds encapsulation. Since the
only use case for MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE destination is
support for tunnel endpoints on VF and trying to offload such rule with
mirror action causes either crash in fs_core or firmware error with
syndrome 0xff6a1d, reject all such rules in mlx5 TC layer.

Fixes: 10742efc ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When handling FIB_EVENT_ENTRY_REPLACE event for a new multipath route,
lag activation can be missed if a stale (struct lag_mp)->mfi pointer
exists, which was associated with an older multipath route that had been
removed.

Normally, when a route is removed, it triggers mlx5_lag_fib_event(),
which handles FIB_EVENT_ENTRY_DEL and clears mfi pointer. But, if
mlx5_lag_check_prereq() condition isn't met, for example when eswitch is
in legacy mode, the fib event is skipped and mfi pointer becomes stale.

Fix by resetting mfi pointer to NULL every time mlx5_lag_mp_init() is
called.

Fixes: 544fe7c2 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

mlx5e_attach_netdev can be called prior to registering the netdevice:
Example stack:

ipoib_new_child_link ->
ipoib_intf_init->
rdma_init_netdev->
mlx5_rdma_setup_rn->

mlx5e_attach_netdev->
mlx5e_num_channels_changed ->
mlx5e_set_default_xps_cpumasks ->
netif_set_xps_queue ->
__netif_set_xps_queue -> kmalloc

If any later stage fails at any point after mlx5e_num_channels_changed()
returns, XPS allocated maps will never be freed as they
are only freed during netdev unregistration, which will never happen for
yet to be registered netdevs.

Fixes: 3909a12e ("net/mlx5e: Fix configuration of XPS cpumasks and netdev queues in corner cases")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>

For unreachable route entry the fib dev does not exists.

Fixes: 8914add2 ("net/mlx5e: Handle FIB events to update tunnel endpoint device")
Reported-by: Dennis Afanasev <dennis.afanasev@stateless.net>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

It could be the lag dev is null so stop processing the event.
In bond_enslave() the active/backup slave being set before setting the
upper dev so first event is without an upper dev.
After setting the upper dev with bond_master_upper_dev_link() there is
a second event and in that event we have an upper dev.

Fixes: 7e51891a ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The result of __dev_get_by_index() is not checked for NULL, which then
passed to mlx5e_attach_encap() and gets dereferenced.

Also, in case of a successful lookup, the net_device reference count is
not incremented, which may result in net_device pointer becoming invalid
at any time during mlx5e_attach_encap() execution.

Fix by using dev_get_by_index(), which does proper reference counting on
the net_device pointer. Also, handle nullptr return value when mirred
device is not found.

It's safe to call dev_put() on the mirred net_device pointer, right
after mlx5e_attach_encap() call, because it's not being saved/copied
down the call chain.

Fixes: 3c37745e ("net/mlx5e: Properly deal with encap flows add/del under neigh update")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When a SF is inactivated and when it is in a TEARDOWN_REQUEST
state, driver still returns its state as active. This is incorrect.
Fix it by treating TEARDOWN_REQEUST as inactive state. When a SF
is still attached to the driver, on user request to reactivate EINVAL
error is returned. Inform user about it with better code EBUSY and
informative error message.

Fixes: 6a327321 ("net/mlx5: SF, Port function state change support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Fix print to print correct error code and not using IS_ERR() which
will just result in always printing 1.
Also return real err instead of always -EOPNOTSUPP.

Fixes: 10caabda ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

For remote mirroring, after the tunnel packets are received, they are
decapsulated and sent to representor, then re-encapsulated and sent
out over another tunnel. So reformat action is set only when the
destination is required to do encapsulation.

Fixes: 249ccc3c ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The result of dev_get_by_index_rcu() is not checked for NULL and then
gets dereferenced immediately.

Also, the RCU lock must be held by the caller of dev_get_by_index_rcu(),
which isn't satisfied by the call stack.

Fix by handling nullptr return value when iflink device is not found.
Add RCU locking around dev_get_by_index_rcu() to avoid possible adverse
effects while iterating over the net_device's hlist.

It is safe not to increment reference count of the net_device pointer in
case of a successful lookup, because it's already handled by VLAN code
during VLAN device registration (see register_vlan_dev and
netdev_upper_dev_link).

Fixes: 278748a9 ("net/mlx5e: Offload TC e-switch rules with egress VLAN device")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

mlx5_core_dev holds pointer to static profile, hence when the
log_max_qp of the profile is override by some device, then it
effect all other mlx5 devices that share the same profile.
Fix it by having a profile instance for every mlx5 device.

Fixes: 883371c4 ("net/mlx5: Check FW limitations on log_max_qp before setting it")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Huazhong Tan says:

====================
net: hns3: fixes for -net

This series includes some bugfixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently skb_checksum_help()'s return is ignored, but it may
return error when it fails to allocate memory when linearizing.

So adds checking for the return of skb_checksum_help().

Fixes: 76ad4f0e("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Fixes: 3db084d2("net: hns3: Fix for vxlan tx checksum bug")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when adaptive is on, the user's coalesce configuration
may be overwritten by the dynamic one. The reason is that user's
configurations are saved in struct hns3_enet_tqp_vector whose
value maybe changed by the dynamic algorithm. To fix it, use
struct hns3_nic_priv instead of struct hns3_enet_tqp_vector to
save and get the user's configuration.

BTW, operations of storing and restoring coalesce info in the reset
process are unnecessary now, so remove them as well.

Fixes: 434776a5 ("net: hns3: add ethtool_ops.set_coalesce support to PF")
Fixes: 7e96adc4 ("net: hns3: add ethtool_ops.get_coalesce support to PF")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the netdevice is registered before client initializing
complete. So there is a timewindow between netdevice available
and usable. In this case, if user try to change the channel number
or ring param, it may cause the hns3_set_rx_cpu_rmap() being called
twice, and report bug.

[47199.416502] hns3 0000:35:00.0 eth1: set channels: tqp_num=1, rxfh=0
[47199.430340] hns3 0000:35:00.0 eth1: already uninitialized
[47199.438554] hns3 0000:35:00.0: rss changes from 4 to 1
[47199.511854] hns3 0000:35:00.0: Channels changed, rss_size from 4 to 1, tqps from 4 to 1
[47200.163524] ------------[ cut here ]------------
[47200.171674] kernel BUG at lib/cpu_rmap.c:142!
[47200.177847] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[47200.185259] Modules linked in: hclge(+) hns3(-) hns3_cae(O) hns_roce_hw_v2 hnae3 vfio_iommu_type1 vfio_pci vfio_virqfd vfio pv680_mii(O) [last unloaded: hclge]
[47200.205912] CPU: 1 PID: 8260 Comm: ethtool Tainted: G           O      5.11.0-rc3+ #1
[47200.215601] Hardware name:  , xxxxxx 02/04/2021
[47200.223052] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[47200.230188] pc : cpu_rmap_add+0x38/0x40
[47200.237472] lr : irq_cpu_rmap_add+0x84/0x140
[47200.243291] sp : ffff800010e93a30
[47200.247295] x29: ffff800010e93a30 x28: ffff082100584880
[47200.254155] x27: 0000000000000000 x26: 0000000000000000
[47200.260712] x25: 0000000000000000 x24: 0000000000000004
[47200.267241] x23: ffff08209ba03000 x22: ffff08209ba038c0
[47200.273789] x21: 000000000000003f x20: ffff0820e2bc1680
[47200.280400] x19: ffff0820c970ec80 x18: 00000000000000c0
[47200.286944] x17: 0000000000000000 x16: ffffb43debe4a0d0
[47200.293456] x15: fffffc2082990600 x14: dead000000000122
[47200.300059] x13: ffffffffffffffff x12: 000000000000003e
[47200.306606] x11: ffff0820815b8080 x10: ffff53e411988000
[47200.313171] x9 : 0000000000000000 x8 : ffff0820e2bc1700
[47200.319682] x7 : 0000000000000000 x6 : 000000000000003f
[47200.326170] x5 : 0000000000000040 x4 : ffff800010e93a20
[47200.332656] x3 : 0000000000000004 x2 : ffff0820c970ec80
[47200.339168] x1 : ffff0820e2bc1680 x0 : 0000000000000004
[47200.346058] Call trace:
[47200.349324]  cpu_rmap_add+0x38/0x40
[47200.354300]  hns3_set_rx_cpu_rmap+0x6c/0xe0 [hns3]
[47200.362294]  hns3_reset_notify_init_enet+0x1cc/0x340 [hns3]
[47200.370049]  hns3_change_channels+0x40/0xb0 [hns3]
[47200.376770]  hns3_set_channels+0x12c/0x2a0 [hns3]
[47200.383353]  ethtool_set_channels+0x140/0x250
[47200.389772]  dev_ethtool+0x714/0x23d0
[47200.394440]  dev_ioctl+0x4cc/0x640
[47200.399277]  sock_do_ioctl+0x100/0x2a0
[47200.404574]  sock_ioctl+0x28c/0x470
[47200.409079]  __arm64_sys_ioctl+0xb4/0x100
[47200.415217]  el0_svc_common.constprop.0+0x84/0x210
[47200.422088]  do_el0_svc+0x28/0x34
[47200.426387]  el0_svc+0x28/0x70
[47200.431308]  el0_sync_handler+0x1a4/0x1b0
[47200.436477]  el0_sync+0x174/0x180
[47200.441562] Code: 11000405 79000c45 f8247861 d65f03c0 (d4210000)
[47200.448869] ---[ end trace a01efe4ce42e5f34 ]---

The process is like below:
excuting hns3_client_init
|
register_netdev()
|                           hns3_set_channels()
|                           |
hns3_set_rx_cpu_rmap()      hns3_reset_notify_uninit_enet()
|                               |
|                            quit without calling function
|                            hns3_free_rx_cpu_rmap for flag
|                            HNS3_NIC_STATE_INITED is unset.
|                           |
|                           hns3_reset_notify_init_enet()
|                               |
set HNS3_NIC_STATE_INITED    call hns3_set_rx_cpu_rmap()-- crash

Fix it by calling register_netdev() at the end of function
hns3_client_init().

Fixes: 08a10068 ("net: hns3: re-organize vector handle")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hclge_mbx_handler(), if there are two consecutive mailbox
messages that requires resp_msg, the resp_msg is not cleared
after processing the first message, which will cause the resp_msg
data of second message incorrect.

Fix it by clearing the resp_msg before processing every mailbox
message.

Fixes: bb5790b7 ("net: hns3: refactor mailbox response scheme between PF and VF")
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx already calls skb_tx_timestamp() in its lan78xx_start_xmit().
Override .get_ts_info to also advertise this capability
(SOF_TIMESTAMPING_TX_SOFTWARE) via ethtool.
Signed-off-by: Markus Blöchl <markus.bloechl@ipetronik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to use "struct work_struct" for the finalize work queue
instead of "struct tipc_net_work", as it can get the "net" and "addr"
from tipc_net's other members and there is no need to add extra net
and addr in tipc_net by defining "struct tipc_net_work".

Note that it's safe to get net from tn->bcl as bcl is always released
after the finalize work queue is done.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We spotted a bug recently during a review where a driver was
unregistering a bus that wasn't registered, which would trigger this
BUG_ON().  Let's handle that situation more gracefully, and just print
a warning and return.
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Awogbemila says:

====================
GVE bug fixes

This patch series includes fixes to some bugs in the gve driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SKBs with skb_get_queue_mapping(skb) == tx_cfg.num_queues should also be
considered invalid.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Brujin <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As currently written, if the driver checks for more work (via
gve_tx_poll or gve_rx_poll) before the device posts work and the
irq doorbell is not unmasked
(via iowrite32be(GVE_IRQ_ACK | GVE_IRQ_EVENT, ...)) before the device
attempts to raise an interrupt, an interrupt is lost and this could
potentially lead to the traffic being completely halted. For
example, if a tx queue has already been stopped, the driver won't get
the chance to complete work and egress will be halted.

We need a full memory barrier in the poll
routine to ensure that the irq doorbell is unmasked before the driver
checks for more work.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Brujin <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When freeing notification blocks, we index priv->msix_vectors.
If we failed to allocate priv->msix_vectors (see abort_with_msix_vectors)
this could lead to a NULL pointer dereference if the driver is unloaded.

Fixes: 893ce44d ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Brujin <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we do not get the expected number of vectors from
pci_enable_msix_range, we update priv->num_ntfy_blks but not
priv->mgmt_msix_idx. This patch fixes this so that priv->mgmt_msix_idx
is updated accordingly.

Fixes: f5cedc84 ("gve: Add transmit and receive support")
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correctly check the TX QPL was assigned and unassigned if
other steps in the allocation fail.

Fixes: f5cedc84 (gve: Add transmit and receive support)
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot reports that in mac80211 we have a potential deadlock
between our "local->stop_queue_reasons_lock" (spinlock) and
netlink's nl_table_lock (rwlock). This is because there's at
least one situation in which we might try to send a netlink
message with this spinlock held while it is also possible to
take the spinlock from a hardirq context, resulting in the
following deadlock scenario reported by lockdep:

       CPU0                    CPU1
       ----                    ----
  lock(nl_table_lock);
                               local_irq_disable();
                               lock(&local->queue_stop_reason_lock);
                               lock(nl_table_lock);
  <Interrupt>
    lock(&local->queue_stop_reason_lock);

This seems valid, we can take the queue_stop_reason_lock in
any kind of context ("CPU0"), and call ieee80211_report_ack_skb()
with the spinlock held and IRQs disabled ("CPU1") in some
code path (ieee80211_do_stop() via ieee80211_free_txskb()).

Short of disallowing netlink use in scenarios like these
(which would be rather complex in mac80211's case due to
the deep callchain), it seems the only fix for this is to
disable IRQs while nl_table_lock is held to avoid hitting
this scenario, this disallows the "CPU0" portion of the
reported deadlock.

Note that the writer side (netlink_table_grab()) already
disables IRQs for this lock.

Unfortunately though, this seems like a huge hammer, and
maybe the whole netlink table locking should be reworked.

Reported-by: syzbot+69ff9dff50dcfe14ddd4@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the device_add() for a smcd_dev fails, there's no cleanup step that
rolls back the earlier list_add(). The device subsequently gets freed,
and we end up with a corrupted list.

Add some error handling that removes the device from the list.

Fixes: c6ba7c9b ("net/smc: add base infrastructure for SMC-D and ISM")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If bond_kobj_init() or later kzalloc() in bond_alloc_slave() fail,
then we call kobject_put() on the slave->kobj. This in turn calls
the release function slave_kobj_release() which will always try to
cancel_delayed_work_sync(&slave->notify_work), which shouldn't be
done on an uninitialized work struct.

Always initialize the work struct earlier to avoid problems here.

Syzbot bisected this down to a completely pointless commit, some
fault injection may have been at work here that caused the alloc
failure in the first place, which may interact badly with bisect.

Reported-by: syzbot+bfda097c12a00c8cae67@syzkaller.appspotmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The http://www.linuxfoundation.org/en/Net does not contain networking
subsystem description ("Nothing found").
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some host, a crash could be triggered simply by repeating these
commands several times:

  # modprobe tipc
  # tipc bearer enable media udp name UDP1 localip 127.0.0.1
  # rmmod tipc

  [] BUG: unable to handle kernel paging request at ffffffffc096bb00
  [] Workqueue: events 0xffffffffc096bb00
  [] Call Trace:
  []  ? process_one_work+0x1a7/0x360
  []  ? worker_thread+0x30/0x390
  []  ? create_worker+0x1a0/0x1a0
  []  ? kthread+0x116/0x130
  []  ? kthread_flush_work_fn+0x10/0x10
  []  ? ret_from_fork+0x35/0x40

When removing the TIPC module, the UDP tunnel sock will be delayed to
release in a work queue as sock_release() can't be done in rtnl_lock().
If the work queue is schedule to run after the TIPC module is removed,
kernel will crash as the work queue function cleanup_beareri() code no
longer exists when trying to invoke it.

To fix it, this patch introduce a member wq_count in tipc_net to track
the numbers of work queues in schedule, and  wait and exit until all
work queues are done in tipc_exit_net().

Fixes: d0f91938 ("tipc: add ip/udp media type")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mld_newpack() doesn't allow to allocate high order page,
only order-0 allocation is allowed.
If headroom size is too large, a kernel panic could occur in skb_put().

Test commands:
    ip netns del A
    ip netns del B
    ip netns add A
    ip netns add B
    ip link add veth0 type veth peer name veth1
    ip link set veth0 netns A
    ip link set veth1 netns B

    ip netns exec A ip link set lo up
    ip netns exec A ip link set veth0 up
    ip netns exec A ip -6 a a 2001:db8:0::1/64 dev veth0
    ip netns exec B ip link set lo up
    ip netns exec B ip link set veth1 up
    ip netns exec B ip -6 a a 2001:db8:0::2/64 dev veth1
    for i in {1..99}
    do
        let A=$i-1
        ip netns exec A ip link add ip6gre$i type ip6gre \
	local 2001:db8:$A::1 remote 2001:db8:$A::2 encaplimit 100
        ip netns exec A ip -6 a a 2001:db8:$i::1/64 dev ip6gre$i
        ip netns exec A ip link set ip6gre$i up

        ip netns exec B ip link add ip6gre$i type ip6gre \
	local 2001:db8:$A::2 remote 2001:db8:$A::1 encaplimit 100
        ip netns exec B ip -6 a a 2001:db8:$i::2/64 dev ip6gre$i
        ip netns exec B ip link set ip6gre$i up
    done

Splat looks like:
kernel BUG at net/core/skbuff.c:110!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
CPU: 0 PID: 7 Comm: kworker/0:1 Not tainted 5.12.0+ #891
Workqueue: ipv6_addrconf addrconf_dad_work
RIP: 0010:skb_panic+0x15d/0x15f
Code: 92 fe 4c 8b 4c 24 10 53 8b 4d 70 45 89 e0 48 c7 c7 00 ae 79 83
41 57 41 56 41 55 48 8b 54 24 a6 26 f9 ff <0f> 0b 48 8b 6c 24 20 89
34 24 e8 4a 4e 92 fe 8b 34 24 48 c7 c1 20
RSP: 0018:ffff88810091f820 EFLAGS: 00010282
RAX: 0000000000000089 RBX: ffff8881086e9000 RCX: 0000000000000000
RDX: 0000000000000089 RSI: 0000000000000008 RDI: ffffed1020123efb
RBP: ffff888005f6eac0 R08: ffffed1022fc0031 R09: ffffed1022fc0031
R10: ffff888117e00187 R11: ffffed1022fc0030 R12: 0000000000000028
R13: ffff888008284eb0 R14: 0000000000000ed8 R15: 0000000000000ec0
FS:  0000000000000000(0000) GS:ffff888117c00000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8b801c5640 CR3: 0000000033c2c006 CR4: 00000000003706f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 ? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
 ? ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
 skb_put.cold.104+0x22/0x22
 ip6_mc_hdr.isra.26.constprop.46+0x12a/0x600
 ? rcu_read_lock_sched_held+0x91/0xc0
 mld_newpack+0x398/0x8f0
 ? ip6_mc_hdr.isra.26.constprop.46+0x600/0x600
 ? lock_contended+0xc40/0xc40
 add_grhead.isra.33+0x280/0x380
 add_grec+0x5ca/0xff0
 ? mld_sendpack+0xf40/0xf40
 ? lock_downgrade+0x690/0x690
 mld_send_initial_cr.part.34+0xb9/0x180
 ipv6_mc_dad_complete+0x15d/0x1b0
 addrconf_dad_completed+0x8d2/0xbb0
 ? lock_downgrade+0x690/0x690
 ? addrconf_rs_timer+0x660/0x660
 ? addrconf_dad_work+0x73c/0x10e0
 addrconf_dad_work+0x73c/0x10e0

Allowing high order page allocation could fix this problem.

Fixes: 72e09ad1 ("ipv6: avoid high order allocations")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'nj_setup' in netjet.c might fail with -EIO and in this case
'card->irq' is initialized and is bigger than zero. A subsequent call to
'nj_release' will free the irq that has not been requested.

Fix this bug by deleting the previous assignment to 'card->irq' and just
keep the assignment before 'request_irq'.

The KASAN's log reveals it:

[    3.354615 ] WARNING: CPU: 0 PID: 1 at kernel/irq/manage.c:1826
free_irq+0x100/0x480
[    3.355112 ] Modules linked in:
[    3.355310 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted
5.13.0-rc1-00144-g25a12987 #13
[    3.355816 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[    3.356552 ] RIP: 0010:free_irq+0x100/0x480
[    3.356820 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18
4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5
ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80
[    3.358012 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082
[    3.358357 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX:
0000000000000000
[    3.358814 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI:
00000000ffffffff
[    3.359272 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09:
0000000000000000
[    3.359732 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12:
0000000000000000
[    3.360195 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15:
ffff888104dc80a8
[    3.360652 ] FS:  0000000000000000(0000) GS:ffff88817bc00000(0000)
knlGS:0000000000000000
[    3.361170 ] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    3.361538 ] CR2: 0000000000000000 CR3: 000000000582e000 CR4:
00000000000006f0
[    3.362003 ] DR0: 0000000000000000 DR1: 0000000000000000 DR2:
0000000000000000
[    3.362175 ] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7:
0000000000000400
[    3.362175 ] Call Trace:
[    3.362175 ]  nj_release+0x51/0x1e0
[    3.362175 ]  nj_probe+0x450/0x950
[    3.362175 ]  ? pci_device_remove+0x110/0x110
[    3.362175 ]  local_pci_probe+0x45/0xa0
[    3.362175 ]  pci_device_probe+0x12b/0x1d0
[    3.362175 ]  really_probe+0x2a9/0x610
[    3.362175 ]  driver_probe_device+0x90/0x1d0
[    3.362175 ]  ? mutex_lock_nested+0x1b/0x20
[    3.362175 ]  device_driver_attach+0x68/0x70
[    3.362175 ]  __driver_attach+0x124/0x1b0
[    3.362175 ]  ? device_driver_attach+0x70/0x70
[    3.362175 ]  bus_for_each_dev+0xbb/0x110
[    3.362175 ]  ? rdinit_setup+0x45/0x45
[    3.362175 ]  driver_attach+0x27/0x30
[    3.362175 ]  bus_add_driver+0x1eb/0x2a0
[    3.362175 ]  driver_register+0xa9/0x180
[    3.362175 ]  __pci_register_driver+0x82/0x90
[    3.362175 ]  ? w6692_init+0x38/0x38
[    3.362175 ]  nj_init+0x36/0x38
[    3.362175 ]  do_one_initcall+0x7f/0x3d0
[    3.362175 ]  ? rdinit_setup+0x45/0x45
[    3.362175 ]  ? rcu_read_lock_sched_held+0x4f/0x80
[    3.362175 ]  kernel_init_freeable+0x2aa/0x301
[    3.362175 ]  ? rest_init+0x2c0/0x2c0
[    3.362175 ]  kernel_init+0x18/0x190
[    3.362175 ]  ? rest_init+0x2c0/0x2c0
[    3.362175 ]  ? rest_init+0x2c0/0x2c0
[    3.362175 ]  ret_from_fork+0x1f/0x30
[    3.362175 ] Kernel panic - not syncing: panic_on_warn set ...
[    3.362175 ] CPU: 0 PID: 1 Comm: swapper/0 Not tainted
5.13.0-rc1-00144-g25a12987 #13
[    3.362175 ] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[    3.362175 ] Call Trace:
[    3.362175 ]  dump_stack+0xba/0xf5
[    3.362175 ]  ? free_irq+0x100/0x480
[    3.362175 ]  panic+0x15a/0x3f2
[    3.362175 ]  ? __warn+0xf2/0x150
[    3.362175 ]  ? free_irq+0x100/0x480
[    3.362175 ]  __warn+0x108/0x150
[    3.362175 ]  ? free_irq+0x100/0x480
[    3.362175 ]  report_bug+0x119/0x1c0
[    3.362175 ]  handle_bug+0x3b/0x80
[    3.362175 ]  exc_invalid_op+0x18/0x70
[    3.362175 ]  asm_exc_invalid_op+0x12/0x20
[    3.362175 ] RIP: 0010:free_irq+0x100/0x480
[    3.362175 ] Code: 6e 08 74 6f 4d 89 f4 e8 5e ac 09 00 4d 8b 74 24 18
4d 85 f6 75 e3 e8 4f ac 09 00 8b 75 c8 48 c7 c7 78 c1 2e 85 e8 e0 cf f5
ff <0f> 0b 48 8b 75 c0 4c 89 ff e8 72 33 0b 03 48 8b 43 40 4c 8b a0 80
[    3.362175 ] RSP: 0000:ffffc90000017b48 EFLAGS: 00010082
[    3.362175 ] RAX: 0000000000000000 RBX: ffff888104dc8000 RCX:
0000000000000000
[    3.362175 ] RDX: ffff8881003c8000 RSI: ffffffff8124a9e6 RDI:
00000000ffffffff
[    3.362175 ] RBP: ffffc90000017b88 R08: 0000000000000000 R09:
0000000000000000
[    3.362175 ] R10: ffffc900000179f0 R11: 0000000000001d04 R12:
0000000000000000
[    3.362175 ] R13: ffff888107dc6000 R14: ffff888107dc6928 R15:
ffff888104dc80a8
[    3.362175 ]  ? vprintk+0x76/0x150
[    3.362175 ]  ? free_irq+0x100/0x480
[    3.362175 ]  nj_release+0x51/0x1e0
[    3.362175 ]  nj_probe+0x450/0x950
[    3.362175 ]  ? pci_device_remove+0x110/0x110
[    3.362175 ]  local_pci_probe+0x45/0xa0
[    3.362175 ]  pci_device_probe+0x12b/0x1d0
[    3.362175 ]  really_probe+0x2a9/0x610
[    3.362175 ]  driver_probe_device+0x90/0x1d0
[    3.362175 ]  ? mutex_lock_nested+0x1b/0x20
[    3.362175 ]  device_driver_attach+0x68/0x70
[    3.362175 ]  __driver_attach+0x124/0x1b0
[    3.362175 ]  ? device_driver_attach+0x70/0x70
[    3.362175 ]  bus_for_each_dev+0xbb/0x110
[    3.362175 ]  ? rdinit_setup+0x45/0x45
[    3.362175 ]  driver_attach+0x27/0x30
[    3.362175 ]  bus_add_driver+0x1eb/0x2a0
[    3.362175 ]  driver_register+0xa9/0x180
[    3.362175 ]  __pci_register_driver+0x82/0x90
[    3.362175 ]  ? w6692_init+0x38/0x38
[    3.362175 ]  nj_init+0x36/0x38
[    3.362175 ]  do_one_initcall+0x7f/0x3d0
[    3.362175 ]  ? rdinit_setup+0x45/0x45
[    3.362175 ]  ? rcu_read_lock_sched_held+0x4f/0x80
[    3.362175 ]  kernel_init_freeable+0x2aa/0x301
[    3.362175 ]  ? rest_init+0x2c0/0x2c0
[    3.362175 ]  kernel_init+0x18/0x190
[    3.362175 ]  ? rest_init+0x2c0/0x2c0
[    3.362175 ]  ? rest_init+0x2c0/0x2c0
[    3.362175 ]  ret_from_fork+0x1f/0x30
[    3.362175 ] Dumping ftrace buffer:
[    3.362175 ]    (ftrace buffer empty)
[    3.362175 ] Kernel Offset: disabled
[    3.362175 ] Rebooting in 1 seconds..
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: 2 bug fixes.

The first one fixes a bug to properly identify some recently added HyperV
device IDs.  The second one fixes device context memory set up on systems
with 64K page size.

Please queue these for -stable as well.  Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There was a typo in the code that checks for 64K BNXT_PAGE_SHIFT in
bnxt_hwrm_set_pg_attr().  Fix it and make the code more understandable
with a new macro BNXT_SET_CTX_PAGE_ATTR().

Fixes: 1b9394e5 ("bnxt_en: Configure context memory on new devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise, some of the recently added HyperV VF IDs would not be
recognized as VF devices and they would not initialize properly.

Fixes: 7fbf359b ("bnxt_en: Add PCI IDs for Hyper-V VF devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return -EPERM from the error handling case instead of 0, as done
elsewhere in this function.

Fixes: b6016b76 ("[BNX2]: New Broadcom gigabit network driver.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfcmrvl_disconnect fails to free the hci_dev field in struct nci_dev.
Fix this by freeing hci_dev in nci_free_device.

BUG: memory leak
unreferenced object 0xffff888111ea6800 (size 1024):
  comm "kworker/1:0", pid 19, jiffies 4294942308 (age 13.580s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 60 fd 0c 81 88 ff ff  .........`......
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<000000004bc25d43>] kmalloc include/linux/slab.h:552 [inline]
    [<000000004bc25d43>] kzalloc include/linux/slab.h:682 [inline]
    [<000000004bc25d43>] nci_hci_allocate+0x21/0xd0 net/nfc/nci/hci.c:784
    [<00000000c59cff92>] nci_allocate_device net/nfc/nci/core.c:1170 [inline]
    [<00000000c59cff92>] nci_allocate_device+0x10b/0x160 net/nfc/nci/core.c:1132
    [<00000000006e0a8e>] nfcmrvl_nci_register_dev+0x10a/0x1c0 drivers/nfc/nfcmrvl/main.c:153
    [<000000004da1b57e>] nfcmrvl_probe+0x223/0x290 drivers/nfc/nfcmrvl/usb.c:345
    [<00000000d506aed9>] usb_probe_interface+0x177/0x370 drivers/usb/core/driver.c:396
    [<00000000bc632c92>] really_probe+0x159/0x4a0 drivers/base/dd.c:554
    [<00000000f5009125>] driver_probe_device+0x84/0x100 drivers/base/dd.c:740
    [<000000000ce658ca>] __device_attach_driver+0xee/0x110 drivers/base/dd.c:846
    [<000000007067d05f>] bus_for_each_drv+0xb7/0x100 drivers/base/bus.c:431
    [<00000000f8e13372>] __device_attach+0x122/0x250 drivers/base/dd.c:914
    [<000000009cf68860>] bus_probe_device+0xc6/0xe0 drivers/base/bus.c:491
    [<00000000359c965a>] device_add+0x5be/0xc30 drivers/base/core.c:3109
    [<00000000086e4bd3>] usb_set_configuration+0x9d9/0xb90 drivers/usb/core/message.c:2164
    [<00000000ca036872>] usb_generic_driver_probe+0x8c/0xc0 drivers/usb/core/generic.c:238
    [<00000000d40d36f6>] usb_probe_device+0x5c/0x140 drivers/usb/core/driver.c:293
    [<00000000bc632c92>] really_probe+0x159/0x4a0 drivers/base/dd.c:554

Reported-by: syzbot+19bcfc64a8df1318d1c3@syzkaller.appspotmail.com
Fixes: 11f54f22 ("NFC: nci: Add HCI over NCI protocol support")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In current kernels, small allocations never actually fail so this
patch shouldn't affect runtime.

Originally this error handling code written with the idea that if
the "serial->tiocmget" allocation failed, then we would continue
operating instead of bailing out early.  But in later years we added
an unchecked dereference on the next line.

	serial->tiocmget->serial_state_notification = kzalloc();
        ^^^^^^^^^^^^^^^^^^

Since these allocations are never going fail in real life, this is
mostly a philosophical debate, but I think bailing out early is the
correct behavior that the user would want.  And generally it's safer to
bail as soon an error happens.

Fixes: af0de130 ("usb: hso: obey DMA rules in tiocmget")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>