- 05 May, 2014 23 commits
-
-
Mohit Kumar authored
commit 017fcdc3 upstream. This patch corrects iATU programming for cfg1, io and mem viewport. Enable ATU only after configuring it. Signed-off-by:
Mohit Kumar <mohit.kumar@st.com> Signed-off-by:
Ajay Khandelwal <ajay.khandelwal@st.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Mohit Kumar authored
commit dbffdd68 upstream. The Synopsys PCIe core provides one pair of 32-bit BARs (BAR 0 and BAR 1). The BARs can be configured as follows: - One 64-bit BAR: BARs 0 and 1 are combined to form a single 64-bit BAR - Two 32-bit BARs: BARs 0 and 1 are two independent 32-bit BARs This patch corrects 64-bit, non-prefetchable memory BAR configuration implemented in dw driver. Signed-off-by:
-
Neil Horman authored
commit 6f8a1b33 upstream. Commit 03bbcb2e (iommu/vt-d: add quirk for broken interrupt remapping on 55XX chipsets) properly disables irq remapping on the 5500/5520 chipsets that don't correctly perform that feature. However, when I wrote it, I followed the errata sheet linked in that commit too closely, and explicitly tied the activation of the quirk to revision 0x13 of the chip, under the assumption that earlier revisions were not in the field. Recently a system was reported to be suffering from this remap bug and the quirk hadn't triggered, because the revision id register read at a lower value that 0x13, so the quirk test failed improperly. Given this, it seems only prudent to adjust this quirk so that any revision less than 0x13 has the quirk asserted. [ tglx: Removed the 0x12 comparison of pci id 3405 as this is covered by the <= 0x13 check already ] Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: x86@kernel.org Link: http://lkml.kernel.org/r/1394649873-14913-1-git-send-email-nhorman@tuxdriver.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Mikulas Patocka authored
commit e79323bd upstream. smp_read_barrier_depends() can be used if there is data dependency between the readers - i.e. if the read operation after the barrier uses address that was obtained from the read operation before the barrier. In this file, there is only control dependency, no data dependecy, so the use of smp_read_barrier_depends() is incorrect. The code could fail in the following way: * the cpu predicts that idx < entries is true and starts executing the body of the for loop * the cpu fetches map->extent[0].first and map->extent[0].count * the cpu fetches map->nr_extents * the cpu verifies that idx < extents is true, so it commits the instructions in the body of the for loop The problem is that in this scenario, the cpu read map->extent[0].first and map->nr_extents in the wrong order. We need a full read memory barrier to prevent it. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Oliver Neukum authored
commit 5c551e62 upstream. Some BIOSes change hardware based on the state of a laptop's lid. If the lid is closed, the touchpad is disabled and the checksum changes. Windows 8 no longer aborts resume if the checksum has changed. Signed-off-by:
Oliver Neukum <oneukum@suse.de> [rjw: Use pr_crit() for the message and don't break the string] Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
LEROY Christophe authored
commit ae2163be upstream. Commit beb2dc0a breaks the MPC8xx which seems to not support using mfspr SPRN_TBRx instead of mftb/mftbu despite what is written in the reference manual. This patch reverts to the use of mftb/mftbu when CONFIG_8xx is selected. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
Scott Wood <scottwood@freescale.com> Signed-off-by:
-
Helge Deller authored
commit ab3e55b1 upstream. This bug was detected with the libio-epoll-perl debian package where the test case IO-Ppoll-compat.t failed. Signed-off-by:
Helge Deller <deller@gmx.de> CC: stable@kernel.org # 3.0+ Signed-off-by:
-
Wang, Xiaoming authored
commit b04c4619 upstream. Plug a group_info refcount leak in ping_init. group_info is only needed during initialization and the code failed to release the reference on exit. While here move grabbing the reference to a place where it is actually needed. Signed-off-by:
Chuansheng Liu <chuansheng.liu@intel.com> Signed-off-by:
Zhang Dongxing <dongxing.zhang@intel.com> Signed-off-by:
xiaoming wang <xiaoming.wang@intel.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Paolo Bonzini authored
commit 5678de3f upstream. QE reported that they got the BUG_ON in ioapic_service to trigger. I cannot reproduce it, but there are two reasons why this could happen. The less likely but also easiest one, is when kvm_irq_delivery_to_apic does not deliver to any APIC and returns -1. Because irqe.shorthand == 0, the kvm_for_each_vcpu loop in that function is never reached. However, you can target the similar loop in kvm_irq_delivery_to_apic_fast; just program a zero logical destination address into the IOAPIC, or an out-of-range physical destination address. Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Bodo Stroesser authored
commit 48e8ac29 upstream. With recent changes it is possible for the timer handler to detect an idle interface and not start the timer, but the thread to start an operation at the same time. The thread will not start the timer in that instance, resulting in the timer not running. Instead, move all timer operations under the lock and start the timer in the thread if it detect non-idle and the timer is not already running. Moving under locks allows the last timeout to be set in both the thread and the timer. 'Timer is not running' means that the timer is not pending and smi_timeout() is not running. So we need a flag to detect this correctly. Also fix a few other timeout bugs: setting the last timeout when the interrupt has to be disabled and the timer started, and setting the last timeout in check_start_timer_thread possibly racing with the timer Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
Bodo Stroesser <bstroesser@ts.fujitsu.com> Signed-off-by:
-
Rusty Russell authored
commit 1f74ef0f upstream. When adding or removing 100G from a balloon: BUG: soft lockup - CPU#0 stuck for 22s! [vballoon:367] We have a wait_event_interruptible(), but the condition is always true (more ballooning to do) so we don't ever sleep. We also have a wait_event() for the host to ack, but that is also always true as QEMU is synchronous for balloon operations. Reported-by:
Gopesh Kumar Chaudhary <gopchaud@in.ibm.com> Cc: stable@kernel.org Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Jan Kara authored
commit 5acda9d1 upstream. After commit 839a8e86 ("writeback: replace custom worker pool implementation with unbound workqueue") when device is removed while we are writing to it we crash in bdi_writeback_workfn() -> set_worker_desc() because bdi->dev is NULL. This can happen because even though bdi_unregister() cancels all pending flushing work, nothing really prevents new ones from being queued from balance_dirty_pages() or other places. Fix the problem by clearing BDI_registered bit in bdi_unregister() and checking it before scheduling of any flushing work. Fixes: 839a8e86Reviewed-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Jan Kara <jack@suse.cz> Cc: Derek Basehore <dbasehore@chromium.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Derek Basehore authored
commit 6ca738d6 upstream. bdi_wakeup_thread_delayed() used the mod_delayed_work() function to schedule work to writeback dirty inodes. The problem with this is that it can delay work that is scheduled for immediate execution, such as the work from sync_inodes_sb(). This can happen since mod_delayed_work() can now steal work from a work_queue. This fixes the problem by using queue_delayed_work() instead. This is a regression caused by commit 839a8e86 ("writeback: replace custom worker pool implementation with unbound workqueue"). The reason that this causes a problem is that laptop-mode will change the delay, dirty_writeback_centisecs, to 60000 (10 minutes) by default. In the case that bdi_wakeup_thread_delayed() races with sync_inodes_sb(), sync will be stopped for 10 minutes and trigger a hung task. Even if dirty_writeback_centisecs is not long enough to cause a hung task, we still don't want to delay sync for that long. We fix the problem by using queue_delayed_work() when we want to schedule writeback sometime in future. This function doesn't change the timer if it is already armed. For the same reason, we also change bdi_writeback_workfn() to immediately queue the work again in the case that the work_list is not empty. The same problem can happen if the sync work is run on the rescue worker. [jack@suse.cz: update changelog, add comment, use bdi_wakeup_thread_delayed()] Signed-off-by:
Derek Basehore <dbasehore@chromium.org> Reviewed-by:
-
Aravind Gopalakrishnan authored
commit 9d0e8d83 upstream. Update current channel selection logic to include F15h, M30h memory controllers. Refer F15 M30h BKDG D18F2x110[7:6] (DRAM Controller Select Low) (Link:http://support.amd.com/TechDocs/49125_15h_Models_30h-3Fh_BKDG.pdf) Signed-off-by:
Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com> Link: http://lkml.kernel.org/r/1390338216-3873-1-git-send-email-Aravind.Gopalakrishnan@amd.comSigned-off-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
-
Aravind Gopalakrishnan authored
commit fb53a1ab upstream. The workaround for this Erratum is included in AGESA. But BIOSes spun only after Jan2014 will have the fix (atleast server versions of the chip). The erratum affects both embedded and server platforms and since we cannot say with certainity that ALL BIOSes on systems out in the field will have the fix, we should probably insulate ourselves in case BIOS does not do the right thing or someone is using old BIOSes. Refer to Revision Guide for AMD F16h models 00h-0fh, document 51810 Rev. 3.04, November2013 for details on the Erratum. Tested the patch on Fam16h server platform and it works fine. Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sergey Dyasly authored
commit 3159f372 upstream. With LPAE enabled, physical address space is larger than 4GB. Allow mapping any part of it via /dev/mem by using PHYS_MASK to determine valid range. PHYS_MASK covers 40 bits with LPAE enabled and 32 bits otherwise. Reported-by:
Vassili Karpov <av1474@comtv.ru> Signed-off-by:
Sergey Dyasly <dserrg@gmail.com> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Kieran Clancy authored
commit 3eba563e upstream. Address a regression caused by commit ad332c8a: (ACPI / EC: Clear stale EC events on Samsung systems) After the earlier patch, there was found to be a race condition on some earlier Samsung systems (N150/N210/N220). The function acpi_ec_clear was sometimes discarding a new EC event before its GPE was triggered by the system. In the case of these systems, this meant that the "lid open" event was not registered on resume if that was the cause of the wake, leading to problems when attempting to close the lid to suspend again. After testing on a number of Samsung systems, both those affected by the previous EC bug and those affected by the race condition, it seemed that the best course of action was to process rather than discard the events. On Samsung systems which accumulate stale EC events, there does not seem to be any adverse side-effects of running the associated _Q methods. This patch adds an argument to the static function acpi_ec_sync_query so that it may be used within the acpi_ec_clear loop in place of acpi_ec_query_unlocked which was used previously. With thanks to Stefan Biereigel for reporting the issue, and for all the people who helped test the new patch on affected systems. Fixes: ad332c8a (ACPI / EC: Clear stale EC events on Samsung systems) References: https://lkml.kernel.org/r/532FE3B2.9060808@biereigel-wb.de References: https://bugzilla.kernel.org/show_bug.cgi?id=44161#c173Reported-by:
Stefan Biereigel <stefan@biereigel.de> Signed-off-by:
Kieran Clancy <clancy.kieran@gmail.com> Tested-by:
Dennis Jansen <dennis.jansen@web.de> Tested-by:
Nicolas Porcel <nicolasporcel06@gmail.com> Tested-by:
Maurizio D'Addona <mauritiusdadd@gmail.com> Tested-by:
Juan Manuel Cabo <juanmanuel.cabo@gmail.com> Tested-by:
Giannis Koutsou <giannis.koutsou@gmail.com> Tested-by:
-
David Ertman authored
commit b20a7744 upstream. In commit da1e2046, the flow for enabling/disabling an Si errata workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem with iAMT connections dropping on interface down with jumbo frames set. Part of this change was to move the function call disabling the workaround to e1000e_down() from the e1000_setup_rctl() function. The mechanic for disabling of this workaround involves writing several MAC and PHY registers back to hardware defaults. After this commit, when the driver is loaded with the cable out, the PHY registers are not programmed with the correct default values. This causes the device to be capable of transmitting packets, but is unable to recieve them until this workaround is called. The flow of e1000e's open code relies upon calling the above workaround to expicitly program these registers either with jumbo frame appropriate settings or h/w defaults on 82579 and newer hardware. Fix this issue by adding logic to e1000_setup_rctl() that not only calls e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the workaround, but also calls this function to explicitly disable the workaround in the case that jumbo frames are not set. Signed-off-by:
Dave Ertman <davidx.m.ertman@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Chew, Kean ho authored
commit 1b31e9b7 upstream. Add Device ID of Intel BayTrail SMBus Controller. Signed-off-by:
Chew, Kean ho <kean.ho.chew@intel.com> Signed-off-by:
Chew, Chiau Ee <chiau.ee.chew@intel.com> Reviewed-by:
Jean Delvare <jdelvare@suse.de> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Al Viro authored
commit f6500801 upstream. * we need to save the starting point for restarts * reject pathologically short buffers outright Spotted-by:
Denys Vlasenko <dvlasenk@redhat.com> Spotted-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Mikulas Patocka authored
We need to restore all variables including error (as it is done in the upstream kernel). The variable error was errorneously not restored when backporting the patch ede4cebc (prepend_path() needs to reinitialize dentry/vfsmount/mnt on restarts). This should be applied only to the 3.12 series. Signed-off-by:
-
Joe Perches authored
commit 29fc2bc7 upstream. pr_debug_ratelimited should be coded similarly to dev_dbg_ratelimited to reduce the "callbacks suppressed" messages. Add #include <linux/dynamic_debug.h> to printk.h. Unfortunately, this new #include must be after the prototype/declaration of function printk. It may be better to split out these _ratelimited declarations into a separate file one day. Any use of these pr_<foo>_ratelimited functions must also have another specific #include <ratelimited.h>. Most users have this done indirectly via #include <linux/kernel.h> printk.h may not #include <linux/ratelimit.h> as it causes circular dependencies and compilation failures. Signed-off-by:
Joe Perches <joe@perches.com> Tested-by:
Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Joe Perches authored
commit 32e24930 upstream. Fix atm_dbg to use normal pr_debug not dynamic_pr_debug because dynamic_pr_debug may not be compiled in at all. Signed-off-by:
-
- 25 Apr, 2014 6 commits
-
-
Jay Cornwall authored
commit e8d2d82d upstream. This patch corrects the PASID format in the INVALIDATE_IOTLB_PAGES command, which was caused by incorrect information in the AMD IOMMU Architectural Specification v2.01 document. Incorrect format: cmd->data[0][16:23] = PASID[7:0] cmd->data[1][16:27] = PASID[19:8] Correct format: cmd->data[0][16:23] = PASID[15:8] cmd->data[1][16:23] = PASID[7:0] However, this does not affect the IOMMUv2 hardware implementation, and has been corrected since version 2.02 of the specification (available through AMD NDA). Signed-off-by:
Jay Cornwall <jay.cornwall@amd.com> Reviewed-by:
Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Signed-off-by:
Joerg Roedel <joro@8bytes.org> Signed-off-by:
-
Tedd Ho-Jeong An authored
commit ef4e5e4a upstream. This patch adds support for new Intel Bluetooth device. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=8087 ProdID=0a2a Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Ingo Molnar authored
commit c321f7d7 upstream. Otherwise the device is not completely shut down. Signed-off-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
-
Petr Tesarik authored
commit 08d2d00b upstream. The loff_t type may be wider than phys_addr_t (e.g. on 32-bit systems). Consequently, the file offset may be truncated in the assignment. Currently, /dev/mem wraps around, which may cause applications to read or write incorrect regions of memory by accident. Let's follow POSIX file semantics here and return 0 when reading from and -EFBIG when writing to an offset that cannot be represented by a phys_addr_t. Note that the conditional is optimized out by the compiler if loff_t has the same size as phys_addr_t. Signed-off-by:
Petr Tesarik <ptesarik@suse.cz> Signed-off-by:
-
Emil Goode authored
commit 8fc1e8c2 upstream. When brcm80211 firmware is not installed networking hangs. A deadlock happens because we call ieee80211_unregister_hw() from the .start callback of struct ieee80211_ops. When .start is called we are under rtnl lock and ieee80211_unregister_hw() tries to take it again. Function call stack: dev_change_flags() __dev_change_flags() __dev_open() ASSERT_RTNL() <-- Assert rtnl lock ops->ndo_open() .ndo_open = ieee80211_open, ieee80211_open() ieee80211_do_open() drv_start() local->ops->start() .start = brcms_ops_start, brcms_ops_start() brcms_remove() ieee80211_unregister_hw() rtnl_lock() <-- Here we deadlock Introduced by: commit 25b5632f ("brcmsmac: request firmware in .start() callback") This patch fixes the bug by removing the call to brcms_remove() and moves the brcms_request_fw() call to the top of the .start callback to not initiate anything unless firmware is installed. Signed-off-by:
Emil Goode <emilgoode@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Alexei Starovoitov authored
commit b07c2651 upstream. The combination of two commits: commit 8e4e1713 ("openvswitch: Simplify datapath locking.") commit 2537b4dd ("openvswitch:: link upper device for port devices") introduced a bug where upper_dev wasn't unlinked upon netdev_unregister notification The following steps: modprobe openvswitch ovs-dpctl add-dp test ip tuntap add dev tap1 mode tap ovs-dpctl add-if test tap1 ip tuntap del dev tap1 mode tap are causing multiple warnings: [ 62.747557] gre: GRE over IPv4 demultiplexor driver [ 62.749579] openvswitch: Open vSwitch switching datapath [ 62.755087] device test entered promiscuous mode [ 62.765911] device tap1 entered promiscuous mode [ 62.766033] IPv6: ADDRCONF(NETDEV_UP): tap1: link is not ready [ 62.769017] ------------[ cut here ]------------ [ 62.769022] WARNING: CPU: 1 PID: 3267 at net/core/dev.c:5501 rollback_registered_many+0x20f/0x240() [ 62.769023] Modules linked in: openvswitch gre vxlan ip_tunnel libcrc32c ip6table_filter ip6_tables ebtable_nat ebtables nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_CHECKSUM iptable_mangle ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc vhost_net macvtap macvlan vhost kvm_intel kvm dm_crypt iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi hid_generic mxm_wmi eeepc_wmi asus_wmi sparse_keymap dm_multipath psmouse serio_raw usbhid hid parport_pc ppdev firewire_ohci lpc_ich firewire_core e1000e crc_itu_t binfmt_misc igb dca ptp pps_core mac_hid wmi lp parport i2o_config i2o_block video [ 62.769051] CPU: 1 PID: 3267 Comm: ip Not tainted 3.12.0-rc3+ #60 [ 62.769052] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012 [ 62.769053] 0000000000000009 ffff8807f25cbd28 ffffffff8175e575 0000000000000006 [ 62.769055] 0000000000000000 ffff8807f25cbd68 ffffffff8105314c ffff8807f25cbd58 [ 62.769057] ffff8807f2634000 ffff8807f25cbdc8 ffff8807f25cbd88 ffff8807f25cbdc8 [ 62.769059] Call Trace: [ 62.769062] [<ffffffff8175e575>] dump_stack+0x55/0x76 [ 62.769065] [<ffffffff8105314c>] warn_slowpath_common+0x8c/0xc0 [ 62.769067] [<ffffffff8105319a>] warn_slowpath_null+0x1a/0x20 [ 62.769069] [<ffffffff8162a04f>] rollback_registered_many+0x20f/0x240 [ 62.769071] [<ffffffff8162a101>] rollback_registered+0x31/0x40 [ 62.769073] [<ffffffff8162a488>] unregister_netdevice_queue+0x58/0x90 [ 62.769075] [<ffffffff8154f900>] __tun_detach+0x140/0x340 [ 62.769077] [<ffffffff8154fb36>] tun_chr_close+0x36/0x60 [ 62.769080] [<ffffffff811bddaf>] __fput+0xff/0x260 [ 62.769082] [<ffffffff811bdf5e>] ____fput+0xe/0x10 [ 62.769084] [<ffffffff8107b515>] task_work_run+0xb5/0xe0 [ 62.769087] [<ffffffff810029b9>] do_notify_resume+0x59/0x80 [ 62.769089] [<ffffffff813a41fe>] ? trace_hardirqs_on_thunk+0x3a/0x3f [ 62.769091] [<ffffffff81770f5a>] int_signal+0x12/0x17 [ 62.769093] ---[ end trace 838756c62e156ffb ]--- [ 62.769481] ------------[ cut here ]------------ [ 62.769485] WARNING: CPU: 1 PID: 92 at fs/sysfs/inode.c:325 sysfs_hash_and_remove+0xa9/0xb0() [ 62.769486] sysfs: can not remove 'master', no directory [ 62.769486] Modules linked in: openvswitch gre vxlan ip_tunnel libcrc32c ip6table_filter ip6_tables ebtable_nat ebtables nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_CHECKSUM iptable_mangle ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc vhost_net macvtap macvlan vhost kvm_intel kvm dm_crypt iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi hid_generic mxm_wmi eeepc_wmi asus_wmi sparse_keymap dm_multipath psmouse serio_raw usbhid hid parport_pc ppdev firewire_ohci lpc_ich firewire_core e1000e crc_itu_t binfmt_misc igb dca ptp pps_core mac_hid wmi lp parport i2o_config i2o_block video [ 62.769514] CPU: 1 PID: 92 Comm: kworker/1:2 Tainted: G W 3.12.0-rc3+ #60 [ 62.769515] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012 [ 62.769518] Workqueue: events ovs_dp_notify_wq [openvswitch] [ 62.769519] 0000000000000009 ffff880807ad3ac8 ffffffff8175e575 0000000000000006 [ 62.769521] ffff880807ad3b18 ffff880807ad3b08 ffffffff8105314c ffff880807ad3b28 [ 62.769523] 0000000000000000 ffffffff81a87a1f ffff8807f2634000 ffff880037038500 [ 62.769525] Call Trace: [ 62.769528] [<ffffffff8175e575>] dump_stack+0x55/0x76 [ 62.769529] [<ffffffff8105314c>] warn_slowpath_common+0x8c/0xc0 [ 62.769531] [<ffffffff81053236>] warn_slowpath_fmt+0x46/0x50 [ 62.769533] [<ffffffff8123e7e9>] sysfs_hash_and_remove+0xa9/0xb0 [ 62.769535] [<ffffffff81240e96>] sysfs_remove_link+0x26/0x30 [ 62.769538] [<ffffffff81631ef7>] __netdev_adjacent_dev_remove+0xf7/0x150 [ 62.769540] [<ffffffff81632037>] __netdev_adjacent_dev_unlink_lists+0x27/0x50 [ 62.769542] [<ffffffff8163213a>] __netdev_adjacent_dev_unlink_neighbour+0x3a/0x50 [ 62.769544] [<ffffffff8163218d>] netdev_upper_dev_unlink+0x3d/0x140 [ 62.769548] [<ffffffffa033c2db>] netdev_destroy+0x4b/0x80 [openvswitch] [ 62.769550] [<ffffffffa033b696>] ovs_vport_del+0x46/0x60 [openvswitch] [ 62.769552] [<ffffffffa0335314>] ovs_dp_detach_port+0x44/0x60 [openvswitch] [ 62.769555] [<ffffffffa0336574>] ovs_dp_notify_wq+0xb4/0x150 [openvswitch] [ 62.769557] [<ffffffff81075c28>] process_one_work+0x1d8/0x6a0 [ 62.769559] [<ffffffff81075bc8>] ? process_one_work+0x178/0x6a0 [ 62.769562] [<ffffffff8107659b>] worker_thread+0x11b/0x370 [ 62.769564] [<ffffffff81076480>] ? rescuer_thread+0x350/0x350 [ 62.769566] [<ffffffff8107f44a>] kthread+0xea/0xf0 [ 62.769568] [<ffffffff8107f360>] ? flush_kthread_worker+0x150/0x150 [ 62.769570] [<ffffffff81770bac>] ret_from_fork+0x7c/0xb0 [ 62.769572] [<ffffffff8107f360>] ? flush_kthread_worker+0x150/0x150 [ 62.769573] ---[ end trace 838756c62e156ffc ]--- [ 62.769574] ------------[ cut here ]------------ [ 62.769576] WARNING: CPU: 1 PID: 92 at fs/sysfs/inode.c:325 sysfs_hash_and_remove+0xa9/0xb0() [ 62.769577] sysfs: can not remove 'upper_test', no directory [ 62.769577] Modules linked in: openvswitch gre vxlan ip_tunnel libcrc32c ip6table_filter ip6_tables ebtable_nat ebtables nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_CHECKSUM iptable_mangle ipt_REJECT xt_tcpudp iptable_filter ip_tables x_tables bridge stp llc vhost_net macvtap macvlan vhost kvm_intel kvm dm_crypt iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi hid_generic mxm_wmi eeepc_wmi asus_wmi sparse_keymap dm_multipath psmouse serio_raw usbhid hid parport_pc ppdev firewire_ohci lpc_ich firewire_core e1000e crc_itu_t binfmt_misc igb dca ptp pps_core mac_hid wmi lp parport i2o_config i2o_block video [ 62.769603] CPU: 1 PID: 92 Comm: kworker/1:2 Tainted: G W 3.12.0-rc3+ #60 [ 62.769604] Hardware name: System manufacturer System Product Name/P8Z77 WS, BIOS 3007 07/26/2012 [ 62.769606] Workqueue: events ovs_dp_notify_wq [openvswitch] [ 62.769607] 0000000000000009 ffff880807ad3ac8 ffffffff8175e575 0000000000000006 [ 62.769609] ffff880807ad3b18 ffff880807ad3b08 ffffffff8105314c ffff880807ad3b58 [ 62.769611] 0000000000000000 ffff880807ad3bd9 ffff8807f2634000 ffff880037038500 [ 62.769613] Call Trace: [ 62.769615] [<ffffffff8175e575>] dump_stack+0x55/0x76 [ 62.769617] [<ffffffff8105314c>] warn_slowpath_common+0x8c/0xc0 [ 62.769619] [<ffffffff81053236>] warn_slowpath_fmt+0x46/0x50 [ 62.769621] [<ffffffff8123e7e9>] sysfs_hash_and_remove+0xa9/0xb0 [ 62.769622] [<ffffffff81240e96>] sysfs_remove_link+0x26/0x30 [ 62.769624] [<ffffffff81631f22>] __netdev_adjacent_dev_remove+0x122/0x150 [ 62.769627] [<ffffffff81632037>] __netdev_adjacent_dev_unlink_lists+0x27/0x50 [ 62.769629] [<ffffffff8163213a>] __netdev_adjacent_dev_unlink_neighbour+0x3a/0x50 [ 62.769631] [<ffffffff8163218d>] netdev_upper_dev_unlink+0x3d/0x140 [ 62.769633] [<ffffffffa033c2db>] netdev_destroy+0x4b/0x80 [openvswitch] [ 62.769636] [<ffffffffa033b696>] ovs_vport_del+0x46/0x60 [openvswitch] [ 62.769638] [<ffffffffa0335314>] ovs_dp_detach_port+0x44/0x60 [openvswitch] [ 62.769640] [<ffffffffa0336574>] ovs_dp_notify_wq+0xb4/0x150 [openvswitch] [ 62.769642] [<ffffffff81075c28>] process_one_work+0x1d8/0x6a0 [ 62.769644] [<ffffffff81075bc8>] ? process_one_work+0x178/0x6a0 [ 62.769646] [<ffffffff8107659b>] worker_thread+0x11b/0x370 [ 62.769648] [<ffffffff81076480>] ? rescuer_thread+0x350/0x350 [ 62.769650] [<ffffffff8107f44a>] kthread+0xea/0xf0 [ 62.769652] [<ffffffff8107f360>] ? flush_kthread_worker+0x150/0x150 [ 62.769654] [<ffffffff81770bac>] ret_from_fork+0x7c/0xb0 [ 62.769656] [<ffffffff8107f360>] ? flush_kthread_worker+0x150/0x150 [ 62.769657] ---[ end trace 838756c62e156ffd ]--- [ 62.769724] device tap1 left promiscuous mode This patch also affects moving devices between net namespaces. OVS used to ignore netns move notifications which caused problems. Like: ovs-dpctl add-if test tap1 ip link set tap1 netns 3512 and then removing tap1 inside the namespace will cause hang on missing dev_put. With this patch OVS will detach dev upon receiving netns move event. Signed-off-by:
Alexei Starovoitov <ast@plumgrid.com> Signed-off-by:
Jesse Gross <jesse@nicira.com> Signed-off-by:
-
- 18 Apr, 2014 11 commits
-
-
Jiri Slaby authored
-
Ard Biesheuvel authored
commit 8ceee728 upstream. The GHASH setkey() function uses SSE registers but fails to call kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and then having to deal with the restriction that they cannot be called from interrupt context, move the setkey() implementation to the C domain. Note that setkey() does not use any particular SSE features and is not expected to become a performance bottleneck. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by:
H. Peter Anvin <hpa@linux.intel.com> Fixes: 0e1227d3 (crypto: ghash - Add PCLMULQDQ accelerated implementation) Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Vineet Gupta authored
commit 61fb4bfc upstream. Despite the switch to right UART driver (prev patch), serial console still doesn't work due to missing CONFIG_SERIAL_OF_PLATFORM Also fix the default cmdline in DT to not refer to out-of-tree ARC framebuffer driver for console. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <Francois.Bedard@synopsys.com> Signed-off-by:
-
Mischa Jonker authored
commit 6eda477b upstream. The Synopsys APB DW UART has a couple of special features that are not in the System C model. In 3.8, the 8250_dw driver didn't really use these features, but from 3.9 onwards, the 8250_dw driver has become incompatible with our model. Signed-off-by:
Mischa Jonker <mjonker@synopsys.com> Signed-off-by:
-
Sasha Levin authored
[ Upstream commit bf39b424 ] Binding might result in a NULL device which is later dereferenced without checking. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit 7563487c ] There are three buffer overflows addressed in this patch. 1) In isdnloop_fake_err() we add an 'E' to a 60 character string and then copy it into a 60 character buffer. I have made the destination buffer 64 characters and I'm changed the sprintf() to a snprintf(). 2) In isdnloop_parse_cmd(), p points to a 6 characters into a 60 character buffer so we have 54 characters. The ->eazlist[] is 11 characters long. I have modified the code to return if the source buffer is too long. 3) In isdnloop_command() the cbuf[] array was 60 characters long but the max length of the string then can be up to 79 characters. I made the cbuf array 80 characters long and changed the sprintf() to snprintf(). I also removed the temporary "dial" buffer and changed it to use "p" directly. Unfortunately, we pass the "cbuf" string from isdnloop_command() to isdnloop_writecmd() which truncates anything over 60 characters to make it fit in card->omsg[]. (It can accept values up to 255 characters so long as there is a '\n' character every 60 characters). For now I have just fixed the memory corruption bug and left the other problems in this driver alone. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
YOSHIFUJI Hideaki authored
[ Upstream commit 77bc6bed ] Return -EINVAL unless all of user-given strings are correctly NUL-terminated. Signed-off-by:
YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by:
-
Mike Rapoport authored
[ Upstream commit 5933a7bb ] If the vxlan interface is created without explicit group definition, there are corner cases which may cause kernel panic. For instance, in the following scenario: node A: $ ip link add dev vxlan42 address 2c:c2:60:00:10:20 type vxlan id 42 $ ip addr add dev vxlan42 10.0.0.1/24 $ ip link set up dev vxlan42 $ arp -i vxlan42 -s 10.0.0.2 2c:c2:60:00:01:02 $ bridge fdb add dev vxlan42 to 2c:c2:60:00:01:02 dst <IPv4 address> $ ping 10.0.0.2 node B: $ ip link add dev vxlan42 address 2c:c2:60:00:01:02 type vxlan id 42 $ ip addr add dev vxlan42 10.0.0.2/24 $ ip link set up dev vxlan42 $ arp -i vxlan42 -s 10.0.0.1 2c:c2:60:00:10:20 node B crashes: vxlan42: 2c:c2:60:00:10:20 migrated from 4011:eca4:c0a8:6466:c0a8:6415:8e09:2118 to (invalid address) vxlan42: 2c:c2:60:00:10:20 migrated from 4011:eca4:c0a8:6466:c0a8:6415:8e09:2118 to (invalid address) BUG: unable to handle kernel NULL pointer dereference at 0000000000000046 IP: [<ffffffff8143c459>] ip6_route_output+0x58/0x82 PGD 7bd89067 PUD 7bd4e067 PMD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.14.0-rc8-hvx-xen-00019-g97a5221f-dirty #154 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 task: ffff88007c774f50 ti: ffff88007c79c000 task.ti: ffff88007c79c000 RIP: 0010:[<ffffffff8143c459>] [<ffffffff8143c459>] ip6_route_output+0x58/0x82 RSP: 0018:ffff88007fd03668 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffff8186a000 RCX: 0000000000000040 RDX: 0000000000000000 RSI: ffff88007b0e4a80 RDI: ffff88007fd03754 RBP: ffff88007fd03688 R08: ffff88007b0e4a80 R09: 0000000000000000 R10: 0200000a0100000a R11: 0001002200000000 R12: ffff88007fd03740 R13: ffff88007b0e4a80 R14: ffff88007b0e4a80 R15: ffff88007bba0c50 FS: 0000000000000000(0000) GS:ffff88007fd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000046 CR3: 000000007bb60000 CR4: 00000000000006e0 Stack: 0000000000000000 ffff88007fd037a0 ffffffff8186a000 ffff88007fd03740 ffff88007fd036c8 ffffffff814320bb 0000000000006e49 ffff88007b8b7360 ffff88007bdbf200 ffff88007bcbc000 ffff88007b8b7000 ffff88007b8b7360 Call Trace: <IRQ> [<ffffffff814320bb>] ip6_dst_lookup_tail+0x2d/0xa4 [<ffffffff814322a5>] ip6_dst_lookup+0x10/0x12 [<ffffffff81323b4e>] vxlan_xmit_one+0x32a/0x68c [<ffffffff814a325a>] ? _raw_spin_unlock_irqrestore+0x12/0x14 [<ffffffff8104c551>] ? lock_timer_base.isra.23+0x26/0x4b [<ffffffff8132451a>] vxlan_xmit+0x66a/0x6a8 [<ffffffff8141a365>] ? ipt_do_table+0x35f/0x37e [<ffffffff81204ba2>] ? selinux_ip_postroute+0x41/0x26e [<ffffffff8139d0c1>] dev_hard_start_xmit+0x2ce/0x3ce [<ffffffff8139d491>] __dev_queue_xmit+0x2d0/0x392 [<ffffffff813b380f>] ? eth_header+0x28/0xb5 [<ffffffff8139d569>] dev_queue_xmit+0xb/0xd [<ffffffff813a5aa6>] neigh_resolve_output+0x134/0x152 [<ffffffff813db741>] ip_finish_output2+0x236/0x299 [<ffffffff813dc074>] ip_finish_output+0x98/0x9d [<ffffffff813dc749>] ip_output+0x62/0x67 [<ffffffff813da9f2>] dst_output+0xf/0x11 [<ffffffff813dc11c>] ip_local_out+0x1b/0x1f [<ffffffff813dcf1b>] ip_send_skb+0x11/0x37 [<ffffffff813dcf70>] ip_push_pending_frames+0x2f/0x33 [<ffffffff813ff732>] icmp_push_reply+0x106/0x115 [<ffffffff813ff9e4>] icmp_reply+0x142/0x164 [<ffffffff813ffb3b>] icmp_echo.part.16+0x46/0x48 [<ffffffff813c1d30>] ? nf_iterate+0x43/0x80 [<ffffffff813d8037>] ? xfrm4_policy_check.constprop.11+0x52/0x52 [<ffffffff813ffb62>] icmp_echo+0x25/0x27 [<ffffffff814005f7>] icmp_rcv+0x1d2/0x20a [<ffffffff813d8037>] ? xfrm4_policy_check.constprop.11+0x52/0x52 [<ffffffff813d810d>] ip_local_deliver_finish+0xd6/0x14f [<ffffffff813d8037>] ? xfrm4_policy_check.constprop.11+0x52/0x52 [<ffffffff813d7fde>] NF_HOOK.constprop.10+0x4c/0x53 [<ffffffff813d82bf>] ip_local_deliver+0x4a/0x4f [<ffffffff813d7f7b>] ip_rcv_finish+0x253/0x26a [<ffffffff813d7d28>] ? inet_add_protocol+0x3e/0x3e [<ffffffff813d7fde>] NF_HOOK.constprop.10+0x4c/0x53 [<ffffffff813d856a>] ip_rcv+0x2a6/0x2ec [<ffffffff8139a9a0>] __netif_receive_skb_core+0x43e/0x478 [<ffffffff812a346f>] ? virtqueue_poll+0x16/0x27 [<ffffffff8139aa2f>] __netif_receive_skb+0x55/0x5a [<ffffffff8139aaaa>] process_backlog+0x76/0x12f [<ffffffff8139add8>] net_rx_action+0xa2/0x1ab [<ffffffff81047847>] __do_softirq+0xca/0x1d1 [<ffffffff81047ace>] irq_exit+0x3e/0x85 [<ffffffff8100b98b>] do_IRQ+0xa9/0xc4 [<ffffffff814a37ad>] common_interrupt+0x6d/0x6d <EOI> [<ffffffff810378db>] ? native_safe_halt+0x6/0x8 [<ffffffff810110c7>] default_idle+0x9/0xd [<ffffffff81011694>] arch_cpu_idle+0x13/0x1c [<ffffffff8107480d>] cpu_startup_entry+0xbc/0x137 [<ffffffff8102e741>] start_secondary+0x1a0/0x1a5 Code: 24 14 e8 f1 e5 01 00 31 d2 a8 32 0f 95 c2 49 8b 44 24 2c 49 0b 44 24 24 74 05 83 ca 04 eb 1c 4d 85 ed 74 17 49 8b 85 a8 02 00 00 <66> 8b 40 46 66 c1 e8 07 83 e0 07 c1 e0 03 09 c2 4c 89 e6 48 89 RIP [<ffffffff8143c459>] ip6_route_output+0x58/0x82 RSP <ffff88007fd03668> CR2: 0000000000000046 ---[ end trace 4612329caab37efd ]--- When vxlan interface is created without explicit group definition, the default_dst protocol family is initialiazed to AF_UNSPEC and the driver assumes IPv4 configuration. On the other side, the default_dst protocol family is used to differentiate between IPv4 and IPv6 cases and, since, AF_UNSPEC != AF_INET, the processing takes the IPv6 path. Making the IPv4 assumption explicit by settting default_dst protocol family to AF_INET4 and preventing mixing of IPv4 and IPv6 addresses in snooped fdb entries fixes the corner case crashes. Signed-off-by:
Mike Rapoport <mike.rapoport@ravellosystems.com> Signed-off-by:
-
Wei Liu authored
[ Upstream commit e9d8b2c2 ] When netback discovers frontend is sending malformed packet it will disables the interface which serves that frontend. However disabling a network interface involving taking a mutex which cannot be done in softirq context, so we need to defer this process to kthread context. This patch does the following: 1. introduce a flag to indicate the interface is disabled. 2. check that flag in TX path, don't do any work if it's true. 3. check that flag in RX path, turn off that interface if it's true. The reason to disable it in RX path is because RX uses kthread. After this change the behavior of netback is still consistent -- it won't do any TX work for a rogue frontend, and the interface will be eventually turned off. Also change a "continue" to "break" after xenvif_fatal_tx_err, as it doesn't make sense to continue processing packets if frontend is rogue. This is a fix for XSA-90. Reported-by:
Török Edwin <edwin@etorok.net> Signed-off-by:
Wei Liu <wei.liu2@citrix.com> Cc: Ian Campbell <ian.campbell@citrix.com> Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Acked-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
-
Pablo Neira authored
[ Upstream commit 8b7b9324 ] nla_strcmp compares the string length plus one, so it's implicitly including the nul-termination in the comparison. int nla_strcmp(const struct nlattr *nla, const char *str) { int len = strlen(str) + 1; ... d = memcmp(nla_data(nla), str, len); However, if NLA_STRING is used, userspace can send us a string without the nul-termination. This is a problem since the string comparison will not match as the last byte may be not the nul-termination. Fix this by skipping the comparison of the nul-termination if the attribute data is nul-terminated. Suggested by Thomas Graf. Cc: Florian Westphal <fw@strlen.de> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Hannes Frederic Sowa authored
[ Upstream commit 43a43b60 ] After commit c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue") some counters are now updated in process context and thus need to disable bh before doing so, otherwise deadlocks can happen on 32-bit archs. Fabio Estevam noticed this while while mounting a NFS volume on an ARM board. As a compensation for missing this I looked after the other *_STATS_BH and found three other calls which need updating: 1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling) 2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ... (only in case of icmp protocol with raw sockets in error handling) 3) ping6_v6_sendmsg (error handling) Fixes: c15b1cca ("ipv6: move DAD and addrconf_verify processing to workqueue") Reported-by:
Fabio Estevam <festevam@gmail.com> Tested-by:
Fabio Estevam <fabio.estevam@freescale.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
