"unlikely(WARN_ON_ONCE(x))" is excessive. WARN_ON_ONCE() already uses
unlikely() internally.
Signed-off-by: Denis Efremov <efremov@linux.com>
Cc: Boris Pismenny <borisp@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netdev@vger.kernel.org
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new function bnxt_get_registered_vfs() to handle the work
of getting the number of registered VFs under #ifdef CONFIG_BNXT_SRIOV.
The main code will call this function and will always work correctly
whether CONFIG_BNXT_SRIOV is set or not.

Fixes: 230d1f0d ("bnxt_en: Handle firmware reset.")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
Fixes for unlocked cls hardware offload API refactoring

Two fixes for my "Refactor cls hardware offload API to support
rtnl-independent drivers" series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

New local variable "struct flow_block_offload *f" was added to
mlx5e_setup_tc() in recent rtnl lock removal patches. The variable is used
in code that is only compiled when CONFIG_MLX5_ESWITCH is enabled. This
results compilation warning about unused variable when CONFIG_MLX5_ESWITCH
is not set. Move the variable definition into eswitch-specific code block
from the beginning of mlx5e_setup_tc() function.

Fixes: c9f14470 ("net: sched: add API for registering unlocked offload block callbacks")
Reported-by: tanhuazhong <tanhuazhong@huawei.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent rtnl lock removal patch changed flow_action infra to require proper
cleanup besides simple memory deallocation. However, matchall classifier
was not updated to call tc_cleanup_flow_action(). Add proper cleanup to
mall_replace_hw_filter() and mall_reoffload().

Fixes: 5a6ff4b1 ("net: sched: take reference to action dev before calling offloads")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This explicitly clarifies that bbr_bdp() returns the rounded-up value of
the bandwidth-delay product and why in the comments.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement this callback in order to get the offloaded stats added to the
kernel stats.
Reported-by: Pengfei Liu <pengfeil@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 190f73ab ("net: stmmac: setup higher frequency clk support for EHL & TGL")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pointer pkt is being initialized with a value that is never read
and pkt is being re-assigned a little later on. The assignment is
redundant and hence can be removed.

Addresses-Coverity: ("Ununsed value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: health and error recovery.

This patchset implements adapter health and error recovery.  The status
is reported through several devlink reporters and the driver will
initiate and complete the recovery process using the devlink infrastructure.

v2: Added 4 patches at the beginning of the patchset to clean up error code
    handling related to firmware messages and to convert to use standard
    error codes.

    Removed the dropping of rtnl_lock in bnxt_close().

    Broke up the patches some more for better patch organization and
    future bisection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Health show command example and output:

$ devlink health show pci/0000:af:00.0 reporter fw_fatal

pci/0000:af:00.0:
  name fw_fatal
    state healthy error 1 recover 1 grace_period 0 auto_recover true

Fatal events from firmware or missing periodic heartbeats will
be reported and recovery will be handled.

We also turn on the support flags when we register with the firmware to
enable this health and recovery feature in the firmware.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This call will handle fatal firmware errors by forcing a reset on the
firmware.  The master function driver will carry out the forced reset.
The sequence will go through the same bnxt_fw_reset_task() workqueue.
This fatal reset differs from the non-fatal reset at the beginning
stages.  From the BNXT_FW_RESET_STATE_ENABLE_DEV state onwards where
the firmware is coming out of reset, it is practically identical to the
non-fatal reset.

The next patch will add the periodic heartbeat check and the devlink
reporter to report the fatal event and to initiate the bnxt_fw_exception()
call.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This state handles driver initiated chip reset during error recovery.
Only the master function will perform this step during error recovery.
The next patch will add code to initiate this reset from the master
function.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a flag to mark that the firmware has encountered fatal condition.
The driver will not send any more firmware messages and will return
error to the caller.  Fix up some clean up functions to continue
and not abort when the firmware message function returns error.

This is preparation work to fully handle firmware error recovery
under fatal conditions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Retain the VF MAC address, default VLAN, TX rate control, trust settings
of VFs after firmware reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add devlink health reporter for the firmware reset event.  Once we get
the notification from firmware about the impending reset, the driver
will report this to devlink and the call to bnxt_fw_reset() will be
initiated to complete the reset sequence.

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the bnxt_fw_reset() main function to handle firmware reset.  This
is triggered by firmware to initiate an orderly reset, for example
when a non-fatal exception condition has been detected.  bnxt_fw_reset()
will first wait for all VFs to shutdown and then start the
bnxt_fw_reset_task() work queue to go through the sequence of reset,
re-probe, and re-initialization.

The next patch will add the devlink reporter to start the sequence and
call bnxt_fw_reset().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This event from firmware signals a coordinated reset initiated by the
firmware.  It may be triggered by some error conditions encountered
in the firmware or other orderly reset conditions.

We store the parameters from this event.  Subsequent patches will
add logic to handle reset itself using devlink reporters.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create new FW devlink_health_reporter, to know the current health
status of FW.

Command example and output:
$ devlink health show pci/0000:af:00.0 reporter fw

pci/0000:af:00.0:
  name fw
    state healthy error 0 recover 0

 FW status: Healthy; Reset count: 1

Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new flag will be set in subsequent patches when firmware is
going through reset.  If bnxt_close() is called while the new flag
is set, the FW reset sequence will have to be aborted because the
NIC is prematurely closed before FW reset has completed.  We also
reject SRIOV configurations while FW reset is in progress.

v2: No longer drop rtnl_lock() in close and wait for FW reset to complete.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle the async event from the firmware that enables firmware health
monitoring.  Store initial health metrics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pre-map the GRC registers for periodic firmware health monitoring.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call the new firmware API HWRM_ERROR_RECOVERY_QCFG if it is supported
to discover the firmware health and recovery capabilities and settings.
This feature allows the driver to reset the chip if firmware crashes and
becomes unresponsive.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During IF_UP, newer firmware has a new status flag that indicates that
firmware has reset.  Add new function bnxt_fw_init_one() to re-probe the
firmware and re-setup VF resources on the PF if necessary.  If the
re-probe fails, set a flag to prevent bnxt_open() from proceeding again.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When VFs need to be reconfigured dynamically after firmwware reset, the
configuration sequence on the PF needs to be changed to register the VF
buffers first.  Otherwise, some VF firmware commands may not succeed as
there may not be PF buffers ready for the re-directed firmware commands.

This sequencing did not matter much before when we only supported
the normal bring-up of VFs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor the hardware/firmware configuration portion in
bnxt_sriov_enable() into a new function bnxt_cfg_hw_sriov().  This
new function can be called after a firmware reset to reconfigure the
VFs previously enabled.

v2: straight refactor of the code.  Reordering done in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for the new firmware reset feature, some of the logic
in bnxt_init_one() and related functions will be called again after
firmware has reset.  Reset some of the flags and capabilities so that
everything that can change can be re-initialized.  Refactor some
functions to probe firmware versions and capabilities.  Check some
buffers before allocating as they may have been allocated previously.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the silent parameter is set, suppress all messages when there is
no response from firmware.  When polling for firmware to come out of
reset, no response may be normal and we want to suppress the error
messages.  Also, don't poll for the firmware DMA response if Bus Master
is disabled.  This is in preparation for error recovery when firmware
may be in error or reset state or Bus Master is disabled.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are 4 functions handling message forwarding for SR-IOV.  They
check for non-zero firmware response code and then return -1.  There
is no need to do this anymore.  The main messaging function will
now return standard error code.  Since we don't need to examine the
response, we can use the hwrm_send_message() variant which will
take the mutex automatically.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The main firmware messaging function returns the firmware defined error
code and many callers have to convert to standard error code for proper
propagation to userspace.  Convert bnxt_hwrm_do_send_msg() to return
standard error code so we can do away with all the special error code
handling by the many callers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the non-standard -1 code with -EBUSY when there is no firmware
response after waiting for the maximum timeout.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same message is printed 3 times in the code, so use a common function
to do that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Thomas Bogendoerfer says:

====================
ioc3-eth improvements

In my patch series for splitting out the serial code from ioc3-eth
by using a MFD device there was one big patch for ioc3-eth.c,
which wasn't really usefull for reviews. This series contains the
ioc3-eth changes splitted in smaller steps and few more cleanups.
Only the conversion to MFD will be done later in a different series.

Changes in v3:
- no need to check skb == NULL before passing it to dev_kfree_skb_any
- free memory allocated with get_page(s) with free_page(s)
- allocate rx ring with just GFP_KERNEL
- add required alignment for rings in comments

Changes in v2:
- use net_err_ratelimited for printing various ioc3 errors
- added missing clearing of rx buf valid flags into ioc3_alloc_rings
- use __func__ for printing out of memory messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

netif_stop_queue()/netif_wake_qeue() aren't needed for changing
multicast filters.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

emcr in private struct wasn't always protected by spinlock.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The half/full duplex settings for inter packet gap counters/timer were
reversed.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

replace open coded checksum folding by csum_fold.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the homegrown DMA memory allocation, which only works on
SGI-IP27 machines, with the generic dma allocations.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move common code for rx buffer setup into ioc3_alloc_skb and deal
with allocation failures. Also clean up allocation size calculation.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Do tx ring cleaning and freeing of rx buffers, when chip is shutdown and
allocate buffers before bringing chip up.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>