Remove nsim_dellink() implementation. The rtnetlink code sets the
dellink op to unregister_netdevice_queue(), so this is not needed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.

 2) There have been many weird regressions in r8169 since we turned ASPM
    support on, some are still not understood nor completely resolved.
    Let's turn this back off for now. From Heiner Kallweit.

 3) Signess fixes for ethtool speed value handling, from Michael
    Zhivich.

 4) Handle timestamps properly in macb driver, from Paul Thomas.

 5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
    and we're holding a stale protocol header pointer". From Lorenzo
    Bianconi.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  bnxt_en: Reset device on RX buffer errors.
  bnxt_en: Improve RX consumer index validity check.
  net: macb driver, check for SKBTX_HW_TSTAMP
  qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
  broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
  ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
  net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
  net: ip_gre: fix possible use-after-free in erspan_rcv
  r8169: disable ASPM again
  MAINTAINERS: ieee802154: update documentation file pattern
  net: vrf: Fix ping failed when vrf mtu is set to 0
  selftests: add a tc matchall test case
  nfc: nci: Potential off by one in ->pipes[] array
  NFC: nci: Add some bounds checking in nci_hci_cmd_received()

Pull TPM fixes from James Morris:
 "From Jarkko: These are critical fixes for v5.1. Contains also couple
  of new selftests for v5.1 features (partial reads in /dev/tpm0)"

* 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selftests/tpm2: Open tpm dev in unbuffered mode
  selftests/tpm2: Extend tests to cover partial reads
  KEYS: trusted: fix -Wvarags warning
  tpm: Fix the type of the return value in calc_tpm2_event_size()
  KEYS: trusted: allow trusted.ko to initialize w/o a TPM
  tpm: fix an invalid condition in tpm_common_poll
  tpm: turn on TPM on suspend for TPM 1.x

Pull xtensa fixes from Max Filippov:

 - fix syscall number passed to trace_sys_exit

 - fix syscall number initialization in start_thread

 - fix level interpretation in the return_address

 - fix format string warning in init_pmd

* tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix format string warning in init_pmd
  xtensa: fix return_address
  xtensa: fix initialization of pt_regs::syscall in start_thread
  xtensa: use actual syscall number in do_syscall_trace_leave

Michael Chan says:

====================
bnxt_en: 2 bug fixes.

The first patch prevents possible driver crash if we get a bad RX index
from the hardware.  The second patch resets the device when the hardware
reports buffer error to recover from the error.

Please queue these for -stable also.  Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on.  Recover by resetting the device.

Fixes: c0c050c5 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem.  However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range.  Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.

Fixes: fa7e2812 ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use constants provided by ethtool.h for speed and duplex values
instead of raw integer constants to increase code readability.

thunder_bgx already uses SPEED_UNKNOWN and DUPLEX_UNKNOWN constants,
also provided by ethtool.h.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original patch didn't set phydev->autoneg_complete in one exit path.
Fix this.

Fixes: 4950c2ba ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: Simon Horman <horms@verge.net.au>
Tested-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Zhivich says:

====================
ethtool: fix use of SPEED_UNKNOWN constant

This patch series addresses 2 related issues:

1. ethtool_validate_speed() triggers a "signed-unsigned comparison"
warning due to type difference of SPEED_UNKNOWN constant (int)
and argument to ethtool_validate_speed (__u32).

2. some drivers use u16 storage for SPEED_UNKNOWN constant,
resulting in value truncation and thus failure to test against
SPEED_UNKNOWN correctly.

This revised series addresses several feedback comments:
- split up the patch in to series
- do not unnecessarily change drivers that use "int" storage
  for speed values
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.

For example, the following test will print "False":

    u16 speed = SPEED_UNKNOWN;

    if (speed == SPEED_UNKNOWN)
        printf("True");
    else
        printf("False");

Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.

For example, the following test will print "False":

	u16 speed = SPEED_UNKNOWN;

	if (speed == SPEED_UNKNOWN)
	    printf("True");
	else
	    printf("False");

Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building C++ userspace code that includes ethtool.h
with "-Werror -Wall", g++ complains about signed-unsigned comparison in
ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1.

Explicitly cast SPEED_UNKNOWN to __u32 to match type of
ethtool_validate_speed() argument.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Add support for devlink info command

Shalom says:

Expose the following ASIC information via devlink info command:
  - Driver name
  - Hardware revision
  - Firmware PSID
  - Running firmware version

Standard output example:
  $ devlink dev info pci/0000:03:00.0
  pci/0000:03:00.0:
    versions:
        fixed:
          hw.revision A0
          fw.psid MT_2750110033
        running:
          fw.version 13.1910.622

Pretty JSON example:
  $ devlink -jp dev info pci/0000:03:00.0
  {
      "info": {
          "pci/0000:03:00.0": {
              "versions": {
                  "fixed": {
                      "hw.revision": "A0",
                      "fw.psid": "MT_2750110033"
                  },
                  "running": {
                      "fw.version": "13.1910.622"
                  }
              }
          }
      }
  }

v2:
  - Add fw.psid documentation
  - Add driver name
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add firmware parameter id (fw.psid).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose the following ASIC information via devlink info command:
  - Driver name
  - Hardware revision
  - Firmware PSID
  - Running firmware version

Standard output example:
  $ devlink dev info pci/0000:03:00.0
  pci/0000:03:00.0:
    driver mlxsw_spectrum
    versions:
        fixed:
          hw.revision A0
          fw.psid MT_2750110033
        running:
          fw.version 13.1910.622
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add MGIR register. MGIR, Management General Information Register, allows
software to query the hardware and firmware general information.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most, if not all, Quectel devices use dynamic interface numbers, and
users are able to change the USB configuration at will. Matching on for
example interface number is therefore not possible.

Instead, the QMI device can be identified by looking at the interface
class, subclass and protocol (all 0xff), as well as the number of
endpoints. The reason we need to look at the number of endpoints, is
that the diagnostic port interface has the same class, subclass and
protocol as QMI. However, the diagnostic port only has two endpoints,
while QMI has three.

Until now, we have identified the QMI device by combining a match on
class, subclass and protocol, with a call to the function
quectel_diag_detect(). In quectel_diag_detect(), we check if the number
of endpoints matches for known Quectel vendor/product ids.

Adding new vendor/product ids to quectel_diag_detect() is not a good
long-term solution. This commit replaces the function with a quirk, and
applies the quirk to affected Quectel devices that I have been able to
test the change with (EP06, EM12 and EC25). If the quirk is set and the
number of endpoints equal two, we return from qmi_wwan_probe() with
-ENODEV.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lorenzo Bianconi says:

====================
fix possible use-after-free in erspan_v{4,6}

Similar to what I did in commit bb9bd814 ("ipv6: sit: reset ip
header pointer in ipip6_rcv"), fix possible use-after-free in
erspan_rcv and ip6erspan_rcv extracting tunnel metadata since the
packet can be 'uncloned' running __iptunnel_pull_header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

erspan_v6 tunnels run __iptunnel_pull_header on received skbs to remove
erspan header. This can determine a possible use-after-free accessing
pkt_md pointer in ip6erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header

Fixes: 1d7e2ed2 ("net: erspan: refactor existing erspan code")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

erspan tunnels run __iptunnel_pull_header on received skbs to remove
gre and erspan headers. This can determine a possible use-after-free
accessing pkt_md pointer in erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header

Fixes: 1d7e2ed2 ("net: erspan: refactor existing erspan code")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to have control over how many bytes are read or written
the device needs to be opened in unbuffered mode.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

Three new tests added:
1. Send get random cmd, read header in 1st read, read the rest in second
   read - expect success
2. Send get random cmd, read only part of the response, send another
   get random command, read the response - expect success
3. Send get random cmd followed by another get random cmd, without
   reading the first response - expect the second cmd to fail with -EBUSY
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

Fixes the warning reported by Clang:
security/keys/trusted.c:146:17: warning: passing an object that
undergoes default
      argument promotion to 'va_start' has undefined behavior [-Wvarargs]
        va_start(argp, h3);
                       ^
security/keys/trusted.c:126:37: note: parameter of type 'unsigned
char' is declared here
unsigned char *h2, unsigned char h3, ...)
                               ^
Specifically, it seems that both the C90 (4.8.1.1) and C11 (7.16.1.4)
standards explicitly call this out as undefined behavior:

The parameter parmN is the identifier of the rightmost parameter in
the variable parameter list in the function definition (the one just
before the ...). If the parameter parmN is declared with ... or with a
type that is not compatible with the type that results after
application of the default argument promotions, the behavior is
undefined.

Link: https://github.com/ClangBuiltLinux/linux/issues/41
Link: https://www.eskimo.com/~scs/cclass/int/sx11c.htmlSuggested-by: David Laight <David.Laight@aculab.com>
Suggested-by: Denis Kenzior <denkenz@gmail.com>
Suggested-by: James Bottomley <jejb@linux.vnet.ibm.com>
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

calc_tpm2_event_size() has an invalid signature because
it returns a 'size_t' where as its signature says that
it returns 'int'.

Cc: <stable@vger.kernel.org>
Fixes: 4d23cc32 ("tpm: add securityfs support for TPM 2.0 firmware event log")
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

Allow trusted.ko to initialize w/o a TPM. This commit also adds checks
to the exported functions to fail when a TPM is not available.

Fixes: 24073043 ("KEYS: trusted: explicitly use tpm_chip structure...")
Cc: James Morris <jmorris@namei.org>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.

Fixes: 9488585b ("tpm: add support for partial reads")
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.

Fixes: a3fbfae8 ("tpm: take TPM chip power gating out of tpm_transmit()")
Reported-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: James Morris <james.morris@microsoft.com>

Huazhong Tan says:

====================
code optimizations & bugfixes for HNS3 driver

This patchset includes bugfixes and code optimizations for
the HNS3 ethernet controller driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When hclgevf_client_start() fails or VF driver unloaded, there is
nobody to disable keep_alive_timer.

So this patch fixes them.

Fixes: a6d818e3 ("net: hns3: Add vport alive state checking support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The checking of HCLGEVF_STATE_RST_HANDLING flag in the
hclgevf_reset_task_schedule() will make some scheduling of
reset pending fail. This flag will be checked in the
hclgevf_reset_service_task(), it is unnecessary to check it
in the hclgevf_reset_task_schedule(). So this patch removes it.

Fixes: 35a1e503 ("net: hns3: Add VF Reset Service Task to support event handling")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds error handler for the failure of command queue
initialization both PF and VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the command queue needs re-initialization, the mailbox handling
task should do nothing, otherwise this task will just get some error
print.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ongoing lower-level reset will fail when there is a higher-level
reset occurs, so the error handler should deal with this situation.

Fixes: 6a5f6fa3 ("net: hns3: add error handler for hclgevf_reset()")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When hardware reset does not finish, the driver should not
request a new reset, otherwise the ongoing hardware reset
will get problem.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is unnecessary to deal with the new coming reset if
it is lower than the ongoing one.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the reset has been done successfully, the ongoing reset timer
is unnecessary.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>