The default quantization range of the Y'CbCr encodings of sRGB
and AdobeRGB are full range instead of limited range according to
the corresponding standards.

Fix this in the V4L2_MAP_QUANTIZATION_DEFAULT macro.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This adds support for AD5820 autofocus coil, found for example in
Nokia N900 smartphone.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Add documentation for ad5820 device tree binding.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The s5p-tv driver has been replaced by the exynos drm driver for quite a
long time now. Remove this driver to avoid having duplicate drivers,
of which this one is considered dead code by Samsung.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The sh_mobile_csi2 isn't used anymore (was it ever?), so remove it.
Especially since the soc-camera framework is being deprecated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The functionality that was part of the tw686x-kh driver but not of the
mainlined tw686x driver has now been added to the tw686x driver as well.

So this driver no longer adds any functionality not available through
the mainlined driver and it can now be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Document the new touch API.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix up videodev2.h.rst.exceptions]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Support both V4L2_TCH_FMT_TU08 and V4L2_PIX_FMT_GREY for backwards
compatibility.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Function 54 implements access to various RMI4 diagnostic features.

This patch adds support for retrieving this data. It registers a V4L2
device to output the data to user space.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are different datatypes available from a maXTouch chip. Add
support to retrieve reference data as well.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The mXT1386 family of chips have a different architecture which splits
the diagnostic data into 3 columns.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Invert the diagnostic data to match the orientation of the input device.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen may have a margin where not all the matrix is used. Read
the parameters from T9 and T100 and take account of the difference.

Note: this does not read the XORIGIN/YORIGIN fields so it assumes that
the touchscreen starts at (0,0)
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Register a video device to output T37 diagnostic data.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Atmel maXTouch devices have a T37 object which can be used to read raw
touch deltas from the device. This consists of an array of 16-bit
integers, one for each node on the touchscreen matrix.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some touch controllers send out touch data in a similar way to a
greyscale frame grabber.

Add new device type VFL_TYPE_TOUCH:
- This uses a new device prefix v4l-touch for these devices, to stop
  generic capture software from treating them as webcams. Otherwise,
  touch is treated similarly to video capture.
- Add V4L2_INPUT_TYPE_TOUCH
- Add MEDIA_INTF_T_V4L_TOUCH
- Add V4L2_CAP_TOUCH to indicate device is a touch device

Add formats:
- V4L2_TCH_FMT_DELTA_TD16 for signed 16-bit touch deltas
- V4L2_TCH_FMT_DELTA_TD08 for signed 16-bit touch deltas
- V4L2_TCH_FMT_TU16 for unsigned 16-bit touch data
- V4L2_TCH_FMT_TU08 for unsigned 8-bit touch data

This support will be used by:
- Atmel maXTouch (atmel_mxt_ts)
- Synaptics RMI4.
- sur40
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

I'm leaving ITDev, so change to my personal email. My understanding is
that someone at Atmel will take this on once their takeover by Microchip
has settled down.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The primary reason for this change is to prepare for Gen3 support where
there will be more then one possible video source. Each source will have
its own media bus format and code, so it needs to be moved from the per
device structure to a structure used to represent an individual
connection to a video source.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The original drivers code to find a subdevice by looking in the DT grpah
and how the callbacks to the v4l2 async bind framework where poorly
written. The most obvious example of badness was the duplication of data
in the struct rvin_graph_entity.

This patch removes the data duplication, simplifies the parsing of the
DT graph and add checks to the v4l2 callbacks.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The check for if the specific pixelformat is supported on the current
chip should happen in VIDIOC_S_FMT and VIDIOC_TRY_FMT and not when we
try to setup the hardware for streaming.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

This is done in preparation for Gen3 support where media controller
support will be mandatory for the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Fix a error from the original driver where v4l2_device_call_until_err()
where used for the pad specific v4l2 operation set_fmt.  Also fix up the
error path from this fix so if there is an error it will be propagated
to the caller.

The error path label have also been renamed as a result from a
nitpicking review comment since we are fixing other issues here.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Fix a error from the original driver where the wrong error code is
returned if the driver fails to get a IRQ number from
platform_get_irq().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

When Gen3 support is added to the driver more then one possible video
source entity will be possible. Knowing that the name entity is a bad
one, rename it to digital since it will deal with the digital input
source.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Align style with the rest of the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Fix broken indentations and line breaks.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Now that the build of PDF output on media got fixed, re-add it
to the Sphinx PDF build.

Partially reverts 3eb6cd68 ('Documentation: exclude
media documentation from pdf generation').
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

On some places, either an space or the second ':' is missing.

Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

The Sphinx 1.4.x definition for \DUrole is:

\providecommand*{\DUrole}[2]{%
  \ifcsname DUrole#1\endcsname%
    \csname DUrole#1\endcsname{#2}%
  \else% backwards compatibility: try \docutilsrole#1{#2}
    \ifcsname docutilsrole#1\endcsname%
      \csname docutilsrole#1\endcsname{#2}%
    \else%
      #2%
    \fi%
  \fi%
}

This is broken when it is used inside a \begin{alltt} block.
So, replace it by just "#2", as this won't cause troubles, and
it is one of the fallback methods for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Name all ioctl references and make them match the ioctls that
are documented. That will improve the cross-reference index,
as it will have all ioctls and syscalls there.

While here, improve the documentation to make them to look more
like the rest of the document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Name all ioctl references and make them match the ioctls that
are documented. That will improve the cross-reference index,
as it will have all ioctls and syscalls there.

While here, improve the documentation to make them to look more
like the rest of the document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Name all ioctl references and make them match the ioctls that
are documented. That will improve the cross-reference index,
as it will have all ioctls and syscalls there.

While here, improve the documentation to make them to look more
like the rest of the document.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Name all ioctl references and make them match the ioctls that
are documented. That will improve the cross-reference index,
as it will have all ioctls and syscalls there.

While here, improve the documentation, marking the deprecated
ioctls, and making the non-deprecated ones more like the rest
of the media book.

Also, add a notice for ioctls that still require documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Name all ioctl references and make them match the ioctls that
are documented. That will improve the cross-reference index,
as it will have all ioctls and syscalls there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Now that we have an override for the c domain that will do
the right thing for the Kernel, stop abusing on the cpp
domain.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

Enrich math formulas by using the Sphinx math. That will allow
using those formulas on pdf documents as well.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

* docs-next/docs-next: (51 commits)
  docs-rst: add package adjustbox
  docs-rst: Fix an warning when in interactive mode
  docs-rst: Use better colors for note/warning/attention boxes
  docs-rst: conf.py: adjust the size of .. note:: tag
  docs-rst: add support for LaTeX output
  doc-rst: migrate ioctl CEC_DQEVENT to c-domain
  doc-rst: Revert "kernel-doc: fix handling of address_space tags"
  doc-rst: moved *duplicate* warnings to nitpicky mode
  doc-rst:c-domain: ref-name of a function declaration
  doc-rst: add boilerplate to customize c-domain
  docs: Sphinxify gdb-kernel-debugging.txt and move to dev-tools
  docs: sphinxify kmemcheck.txt and move to dev-tools
  docs: sphinxify kmemleak.txt and move it to dev-tools
  docs: sphinxify ubsan.txt and move it to dev-tools
  docs: sphinxify kasan.txt and move to dev-tools
  docs: sphinixfy gcov.txt and move to dev-tools
  docs: sphinxify kcov.txt and move to dev-tools
  docs: sphinxify sparse.txt and move to dev-tools
  docs: sphinxify coccinelle.txt and add it to dev-tools
  docs: create a new dev-tools directory
  ...

We need adjustbox to allow adjusting the size of tables that
are bigger than the line width. There are quite a few of them
at the media books.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>