Should be 5 rather than 4.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christian König <christian.koenig@amd.com>

The hpd (hot plug detect) pin assignment got lost
in the conversion to to the common i2c over aux
code.  Without this information, aux transactions
do not work properly.  Fixes DP failures.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>

This improves the PLL parameters when we work at
the limits of the allowed ranges.
Signed-off-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>

There seem to be stability issues on a number of cards.

bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=76286
https://bugzilla.redhat.com/show_bug.cgi?id=1085785
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=741619Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: matthias.graf@st.ovqu.de
Cc: bp@alien8.de
Cc: stable@vger.kernel.org

Some i2c fixes over DisplayPort.

* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon: Improve vramlimit module param documentation
  drm/radeon: fix audio pin counts for DCE6+ (v2)
  drm/radeon/dp: switch to the common i2c over aux code
  drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
  drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
  drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
  drm/i915: support address only i2c-over-aux transactions
  drm/tegra: dp: Support address-only I2C-over-AUX transactions

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

bochs kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.

Fix this by adding suspend and resume functions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

cirrus kms driver lacks power management support, thus
the vga display doesn't work any more after S3 resume.

Fix this by adding suspend and resume functions.
Also make the mode_set function unblank the screen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This is leftover stuff from my previous doc round which I kinda wanted
to do but didn't yet due to rebase hell.

The modeset helpers and the probing helpers a independent and e.g.
i915 uses the probing stuff but has its own modeset infrastructure. It
hence makes to split this up. While at it add a DOC: comment for the
probing libraray.

It would be rather neat to pull some of the DocBook documenting these
two helpers into in-line DOC: comments. But unfortunately kerneldoc
doesn't support markdown or something similar to make nice-looking
documentation, so the current state is better.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

After thinking about this topic a bit more I've reached the conclusion
that implementing this doesn't make sense:

- The locking is all wrong: set_config(NULL) will also unlink encoders
  and connectors, but those links are protected with the mode_config
  mutex. In the ->disable_plane callback we only hold all modeset
  locks, but eventually we want to switch to just grabbing the
  per-crtc (and maybe per-plane) locks as needed, maybe based on
  ww_mutexes. Having a callback which absolutely needs all modeset
  locks is bad for this conversion.

  Note that the same isn't true for the provided ->update_plane since
  we've audited the crtc helpers to make sure that not encoder or
  connector links are changed.

- There's no way to re-enable the plane with an ->update_plane: The
  connectors/encoder links are lost and so we can't re-enable the
  CRTC. Even without that issue the driver might have reassigned some
  shared resources (as opposed to e.g. DPMS off, where drivers are not
  allowed to do that to make sure the CRTC can be enabled again).

- The semantics don't make much sense: Userspace asked to scan out
  black (or some other color if the driver supports a background
  color), not that the screen be disabled.

- Implementing proper primary plane support (i.e. actually disabling
  the primary plane without disabling the CRTC) is really simple, at
  least if all the hw needs is flipping a bit. The big task is
  auditing all the interactions with other ioctls when the CRTC is on
  but there's no primary plane (e.g. pageflips). And some of that work
  still needs to be done.

Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

this is a typo vs the ums driver, fix to check correct value.

Found initially by Coverity.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Commit 457e77b2 added two checks applied to a
value received from nv_rd32(bios, 0x619f04). But after this new piece of code
is executed, the addr local variable does not hold the same value it used to
hold before the commit. Here is what is was assigned in the original code:
	(u64)(nv_rd32(bios, 0x619f04) & 0xffffff00) << 8
in the committed code it ends up with this value:
	(u64)(nv_rd32(bios, 0x619f04) >> 8) << 8
These expressions are obviously not equivalent.

My Nvidia video card does not show anything on the display when I boot a
kernel containing this commit.

The patch fixes the code so that the new checks are still done, but the
side effect of an incorrect addr value is gone.

Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'omapdrm-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-next

Fixes for omapdrm, some of which were already present in 3.14, and some which
appeared in 3.15-rc1:

- fixes for primary-plane handling which caused crashes
- fix all kinds of uninit issues which prevented from unloading the omapdrm
  module.
- fixes for HDMI enable/disable issues

* tag 'omapdrm-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
  drm/omap: fix the handling of fb ref counts
  drm/omap: protect omap_crtc's event with event_lock spinlock
  drm/omap: Use old_fb to synchronize between successive page flips
  drm/omap: Fix crash when using LCD3 overlay manager
  drm/omap: gem sync: wait on correct events
  drm/omap: Fix memory leak in omap_gem_op_async
  drm/omap: remove warn from debugfs
  drm/omap: remove extra plane->destroy from crtc destroy
  drm/omap: print warning when rotating non-TILER fb
  drm/omap: fix missing unref to fb's buf object
  drm/omap: fix plane rotation
  drm/omap: fix enabling/disabling of video pipeline
  drm/omap: fix missing disable for unused encoder
  drm/omap: fix race issue when unloading omapdrm
  drm/omap: fix DMM driver (un)registration
  drm/omap: fix uninit order in pdev_remove()
  drm/omap: fix output enable/disable sequence

1. Fixing PLL regressions
2. A couple of memory reclocking and DPM fixes
3. Small cleanups

* 'drm-fixes-3.15' of git://people.freedesktop.org/~deathsimple/linux:
  drm/radeon/ci: make sure mc ucode is loaded before checking the size
  drm/radeon/si: make sure mc ucode is loaded before checking the size
  drm/radeon: improve PLL params if we don't match exactly v2
  drm/radeon: memory leak on bo reservation failure. v2
  drm/radeon: fix VCE fence command
  drm/radeon: re-enable mclk dpm on R7 260X asics
  drm/radeon: add support for newer mc ucode on CI (v2)
  drm/radeon: add support for newer mc ucode on SI (v2)
  drm/radeon: apply more strict limits for PLL params v2
  drm/radeon: update CI DPM powertune settings
  drm/radeon: fix runpm handling on APUs (v4)
  drm/radeon: disable mclk dpm on R7 260X

drm/tegra: Fixes for v3.15-rc2

This contains a fix for the host1x driver writing to non-existent syncpt
registers.

A second commit removes an excess pad field in the parameter structure
for the DRM_TEGRA_SUBMIT IOCTL. Archeaology on earlier versions of this
file indicates that this was once there to pad an uneven number of u32
u32 fields, of which one was subsequently removed. Unfortunately nobody
remembered to get rid of the padding when that happened.

Both of these commits are Cc: stable because they fix issues that were
introduced back in v3.10.

* tag 'drm/tegra/for-3.15-rc2' of git://anongit.freedesktop.org/tegra/linux:
  drm/tegra: Remove gratuitous pad field
  gpu: host1x: handle the correct # of syncpt regs

Avoid a possible segfault.
Noticed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Avoid a possible segfault.
Noticed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Otherwise we might be quite off on older chipsets.

v2: keep ref_div minimum
Signed-off-by: Christian König <christian.koenig@amd.com>

On bo reservation failure, we end up leaking fpriv.

v2 (chk): rebased and added missing free on vm failure as well

Fixes: 5e386b57 ("drm/radeon: fix missing bo reservation")
Cc: stable@vger.kernel.org
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Christian König <christian.koenig@amd.com>

Due to a type mismatch that causes an implicit type conversion, the
upper 32 bits of the GPU address have been zeroed out when adding to the
command buffer.

Picked up by Coverity - CID 1198624.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>

If the new mc ucode is available.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Fixes mclk stability on certain asics.

v2: print out mc firmware version used and size

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=75992Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

May fix stability issues with some newer cards.

v2: print out mc firmware version used and size
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Letting post and refernce divider get to big is bad for signal stability.

v2: increase the limit to 210
Signed-off-by: Christian König <christian.koenig@amd.com>

As per internal recommendations.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Don't try and runtime suspend the APU in PX systems.  We
only want to power down the dGPU.

v2: fix harder
v3: fix stupid typo
v4: consolidate runpm enablement to a single flag

bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=75127
https://bugzilla.kernel.org/show_bug.cgi?id=72701Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Setting higher mclks seems to cause stability issues
on some R7 260X boards.  Disable it for now for stability
until we find a proper fix.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=75992Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The version of the drm_tegra_submit structure that was merged all the
way back in 3.10 contains a pad field that was originally intended to
properly pad the following __u64 field. Unfortunately it seems like a
different field was dropped during review that caused this padding to
become unnecessary, but the pad field wasn't removed at that time.

One possible side-effect of this is that since the __u64 following the
pad is now no longer properly aligned, the compiler may (or may not)
introduce padding itself, which results in no predictable ABI.

Rectify this by removing the pad field so that all fields are again
naturally aligned. Technically this is breaking existing userspace ABI,
but given that there aren't any (released) userspace drivers that make
use of this yet, the fallout should be minimal.

Fixes: d43f81cb ("drm/tegra: Add gr2d device")
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Thierry Reding <treding@nvidia.com>

BIT_WORD() truncates rather than rounds, so the loops in
syncpt_thresh_isr() and _host1x_intr_disable_all_syncpt_intrs() use <=
rather than < in an attempt to process the correct number of registers
when rounding of the conversion of count of bits to count of words is
necessary. However, when rounding isn't necessary because the value is
already a multiple of the divisor (as is the case for all values of
nb_pts the code actually sees), this causes one too many registers to
be processed.

Solve this by using and explicit DIV_ROUND_UP() call, rather than
BIT_WORD(), and comparing with < rather than <=.

Fixes: 7ede0b0b ("gpu: host1x: Add syncpoint wait and interrupts")
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Some fixes from Intel.

* tag 'drm-intel-fixes-2014-04-11' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: Always use kref tracking for all contexts.
  drm/i915: do not setup backlight if not available according to VBT
  drm/i915: check VBT for supported backlight type
  drm/i915: Disable self-refresh for untiled fbs on i915gm
  drm/mm: Don't WARN if drm_mm_reserve_node

With the recent primary-plane changes for drm, the primary plane's
framebuffer needs to be ref counted the same way as for
non-primary-planes. This was not done by the omapdrm driver, which
caused the ref count to drop to 0 too early, causing problems.

This patch moves the fb unref and ref from omap_plane_update to
omap_plane_mode_set. This way the fb refs are updated for both primary
and non-primary cases, as omap_plane_update calls omap_plane_mode_set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The vblank_cb callback and the page_flip ioctl can occur together in different
CPU contexts. vblank_cb uses takes tje drm device's event_lock spinlock when
sending the vblank event and updating omap_crtc->event and omap_crtc->od_fb.

Use the same spinlock in page_flip, to make sure the above omap_crtc parameters
are configured sequentially.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

omap_crtc->old_fb is used to check whether the previous page flip has completed
or not. However, it's never initialized to anything, so it's always NULL. This
results in the check to always succeed, and the page_flip to proceed.

Initialize old_fb to the fb that we intend to flip to through page_flip, and
therefore prevent a future page flip to proceed if the last one didn't
complete.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

The channel_names list didn't have a string populated for LCD3 manager, this
results in a crash when the display's output is connected to LCD3. Add an entry
for LCD3.
Reported-by: Somnath Mukherjee <somnath@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

A waiter of the type OMAP_GEM_READ should wait for a buffer to be completely
written, and only then proceed with reading it. A similar logic applies for
waiters with OMAP_GEM_WRITE flag.

Currently the function is_waiting() waits on the read_complete/read_target
counts in the sync object.

This should be the other way round, as a reader should wait for users who are
'writing' to this buffer, and vice versa.

Make readers of the buffer(OMAP_GEM_READ) wait on the write counters, and
writers to the buffer(OMAP_GEM_WRITE) wait on the read counters in is_waiting()
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

In omap_gem_op_async(), if a waiter is not added to the wait list, it needs to
be free'd in the function itself.

Make sure we free the waiter for this case.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Patch dfe96ddc (omapdrm: simplify locking in
the fb debugfs file) removed taking locks when using omapdrm's debugfs
to dump fb objects.

However, in omap_gem_describe we give a WARN is the lock has not been
taken, so that WARN is now seen every time omapdrm debugfs is used.

So, presuming the removal of locks is ok, we can also remove the WARN.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

All the planes, including primary planes, are now destroyed by the drm
framework. Thus we no longer need the explicit call to plane->destroy
from the crtc's destroy function.

This patch removes the call, thus fixing the crash caused by double
freeing the plane.

remove omap_crtc->plane->funcs->destroy(omap_crtc->plane)
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

Print a warning when the user tries to rotate a non-TILER framebuffer.

Also set the rotation to 0, to avoid constant flood of the warnings in
case of page flipping.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>