TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.

When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.

To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-6-pkshih@realtek.com

IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration only if we are going to run on AP
channel. During scanning phase, without this calibration RF performance
is still acceptable because it transmits with low data rate at this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-5-pkshih@realtek.com

RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-4-pkshih@realtek.com

RCK is synchronize RC calibration. Driver triggers this calibration and
sets the result to register. This calibration is needed once when interface
is going to up.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-3-pkshih@realtek.com

DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output good quality signals.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221012083234.20224-2-pkshih@realtek.com

Add  8852b specific constant tables and basic attributes containing
common chip_ops, firmware name, supported TX/RX NSS, number of CAM,
coexistence version, control register set, and so on.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-10-pkshih@realtek.com

When we are going to do RF calibrations, they need BB helpers to control
TX PLCP, power, path and mode. Also, it they need helpers to backup and
restore some registers before and after RF calibrations. Then, use flow of
RF calibrations will be like backup registers, configure calibration,
configure TX parameters, measure calibration result, and finally restore
registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-9-pkshih@realtek.com

To support variant models, such as 1x1 or 1T2R, we need this chip_ops to
change the path accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-8-pkshih@realtek.com

Add to parse PPDU to get frequency and RSSI of received packets.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-7-pkshih@realtek.com

These chip_ops are used to assist BT coexistence module to control chip
specific operations, such as initial, pre-AGC, BT grant, set wifi priority
and tx power, RX gain, and get BT counter.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-6-pkshih@realtek.com

Thermal value reflects temperature that will affect RF performance, so
we re-calibrate RF characteristics if delta of thermal over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-5-pkshih@realtek.com

chip_ops::bb_reset is to reset baseband state after loading parameters,
because its state could be unpredictable at that moment. The other is
chip_ops::bb_sethw that is to set some baseband settings not including in
parameter tables.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-4-pkshih@realtek.com

We need power on function to enable hardware circuits of MAC/BB/RF, and
then download firmware and load PHY parameters. After more settings, it
starts to work. When it enters idle, use power off function to have the
lowest power consumption.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-3-pkshih@realtek.com

This chip_ops is to assist set_channel, because we need setup and restore
hardware before and after set_channel.

Before set_channel, we stop transmitting, reset PPDU status, disable TSSI,
and disable ADC. After set_channel, do opposite things in reverse order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221009125403.19662-2-pkshih@realtek.com

Make the title more future-proof, using rtw88 as a model.

Mention support for RTL8723BU, RTL8192EU, and RTL8188FU.

Correct the module name.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/ecb7512a-07e8-112d-c815-1494582de5f8@gmail.com

The wifi + bluetooth combo chips (RTL8723AU and RTL8723BU) read the
chip vendor from the wrong register because the val32 variable gets
overwritten. Add one more variable to avoid this.

This had no real effect on RTL8723BU. It may have had an effect on
RTL8723AU.

Fixes: 26f1fad2 ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/24af8024-2f07-552b-93d8-38823d8e3cb0@gmail.com

All the initialisation tables, plus rtl8xxxu_rfregs.

Most of them were already static.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/9407f219-a7ba-676e-3d99-154d67b312d2@gmail.com

Set channel in driver side to configure Tx power and channel index
correctly after scan. Before this, beacons with bandwidth larger than
20M bandwidth will be dropped by mac80211 due to frequency mismatch.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221007045900.10823-2-pkshih@realtek.com

Change active scan behavior to fit 6GHz requirements. There are many
different rules on active scan between 6GHz and 2GHz/5GHz, so if the
SSID is not specified, do fast passive scanning and limit number of
probe requests we send for now until new firmware can support all
rules.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221007045900.10823-1-pkshih@realtek.com

set_channel is main function to configure channel and bandwidth for all
layers, namely MAC, BB and RF. Additionally, MAC layer enables CCK rate
checking to avoid wrong rate from driver. BB layer configures SCO
(Sample Clock Offset) for CCK, TX gain error/offset, and reset baseband
hardware circuit after all configurations done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-7-pkshih@realtek.com

The gain tables use different domain index, so we need to convert the index
from subband of chandef. Since these conversion functions can share with
8852b, make generic functions for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-6-pkshih@realtek.com

HFC is short for HCI flow control. These arrays are used to set quota
according to operating modes, which are SCC or download firmware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-5-pkshih@realtek.com

Before loading RF NCTL table, we need to configure IQK/DPK clock and reset
them, and then polling NCTL state ready. Since 8852BE needs additional
one setting, add it by this patch. Also, give them proper names.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-4-pkshih@realtek.com

Without this fix, some non-self packets are used to count CFO (center
frequency offset), and average CFO has unstable variation. Then, it causes
unexpected performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-3-pkshih@realtek.com

This chunk is to set fixed BT LNA2 at level5 when WiFi/BT shared BTG RFC
to improve BT anti-interference ability from adjacent channel. Since all
chips use the same setting, remove chip_ops::btc_bt_aci_imp.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-2-pkshih@realtek.com

By accident, the previous patch duplicated the initialization
of the wake_tx_queue callback. Fix that by removing the new
initializations.

Fixes: a790cc3a ("wifi: mac80211: add wake_tx_queue callback to drivers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

All drivers are now using mac80211 internal queues (iTXQs).
Drop mac80211 internal support for the old push path.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull in wireless/main content since some new code would
otherwise conflict with it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.

As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Start to align the TX handling to only use internal TX queues (iTXQs):

Provide a handler for drivers not having a custom wake_tx_queue
callback and update the documentation.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In case of 4way handshake offload, transition disable policy
updated by the AP during EAPOL 3/4 is not updated to the upper layer.
This results in mismatch between transition disable policy
between the upper layer and the driver. This patch addresses this
issue by updating transition disable policy as part of port
authorization indication.
Signed-off-by: Vinayak Yadawad <vinayak.yadawad@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove unused has_mrr (has multi-rate retry capabilities) member
from struct minstrel_priv (only set once in minstrel_ht_alloc, never
used again).
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This should of course be CONFIG_, not CPTCFG_, which is an
artifact from working with backports.

Fixes: 9dd19538 ("wifi: nl80211/mac80211: clarify link ID in control port TX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

HE added support for dynamic fragmentation inside aggregation
sessions, but no existing driver ever advertises it. Thus,
remove the code for now, it cannot work as-is in MLO. For it
to properly work in MLO, we'd need to validate that the frag
level is identical across all the link bands/iftypes, which
is a good amount of complex code that's just not worth it as
long as no driver has support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the deflink of the station is on 6 GHz, then it won't have HT.
If at the same time we're using MLO, then vif.bss_conf isn't used,
and thus vif.bss_conf.chandef.chan is NULL, causing the code to
crash.

Fix this by just checking for both HT and HE, and refusing the
aggregation session if both are not present. This might be a bit
wrong since it would accept an aggregation session from a peer
that has HE but no HT on 2.4 or 5 GHz, but such a peer shouldn't
exist in the first place, and it probably supports aggregation if
it has HE support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This won't work right at least with the code as it is, so
at least for now just assume it's never set for MLO. It may
very well never change, almost no drivers support it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix the code that sets the DTIM period to always propagate it
into link->conf->dtim_period and not overwrite it, while still
preferring to set it from the beacon data if available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the station has no HT, we deny the aggregation session
but the error message talks about QoS; change it to say HT
instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

It's useful to know which link was used for the association,
mark it when printing the links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Ensure that the link ID matches in auth/assoc continuation,
otherwise we need to reset all the data.

Fixes: 81151ce4 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>