If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.

Fixes: c1ce2f77 ("amd-xgbe: Fix flow control setting logic")
Signed-off-by: tangpengpeng <tangpengpeng@higon.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Break statements were missing for Geneve case in
ndo_udp_tunnel_{add/del}, thereby raw mac matchall
entries were not getting added.

Fixes: c746fc0e("cxgb4: add geneve offload support for T6")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Devlink resources registered with devlink_resource_register() have
to be unregistered.

Fixes: 37923ed6 ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

net/ipv4/igmp.c:1391:6: warning:
 symbol '__ip_mc_inc_group' was not declared. Should it be static?

Fixes: 6e2059b5 ("ipv4/igmp: init group mode as INCLUDE when join source group")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We observed high 99 and 99.9% latencies when doing RPCs with DCTCP. The
problem is triggered when the last packet of a request arrives CE
marked. The reply will carry the ECE mark causing TCP to shrink its cwnd
to 1 (because there are no packets in flight). When the 1st packet of
the next request arrives, the ACK was sometimes delayed even though it
is CWR marked, adding up to 40ms to the RPC latency.

This patch insures that CWR marked data packets arriving will be acked
immediately.

Packetdrill script to reproduce the problem:

0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0

0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4

0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001

0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001

0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 2:3(1) ack 2001

0.200 < [ect0] . 2001:3001(1000) ack 3 win 257
0.200 < [ect0] . 3001:4001(1000) ack 3 win 257
0.200 > [ect01] . 3:3(0) ack 4001

0.210 < [ce] P. 4001:4501(500) ack 3 win 257

+0.001 read(4, ..., 4500) = 4500
+0 write(4, ..., 1) = 1
+0 > [ect01] PE. 3:4(1) ack 4501

+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501   // delayed ack

+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257  // More data
+0 > [ect01] . 4:4(0) ack 6501     // now acks everything

+0.500 < F. 9501:9501(0) ack 4 win 257

Modified based on comments by Neal Cardwell <ncardwell@google.com>
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When received packets are dropped in virtio_net driver, received packets
counter is incremented but bytes counter is not.
As a result, for instance if we drop all packets by XDP, only received
is counted and bytes stays 0, which looks inconsistent.
IMHO received packets/bytes should be counted if packets are produced by
the hypervisor, like what common NICs on physical machines are doing.
So fix the bytes counter.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS fixes from Paul Burton:
 "A couple more MIPS fixes for 4.18:

   - Fix an off-by-one in reporting PCI resource sizes to userland which
     regressed in v3.12.

   - Fix writes to DDR controller registers used to flush write buffers,
     which regressed with some refactoring in v4.2"

* tag 'mips_fixes_4.18_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: ath79: fix register address in ath79_ddr_wb_flush()
  MIPS: Fix off-by-one in pci_resource_to_user()

Pull networking fixes from David Miller:

 1) Handle stations tied to AP_VLANs properly during mac80211 hw
    reconfig. From Manikanta Pubbisetty.

 2) Fix jump stack depth validation in nf_tables, from Taehee Yoo.

 3) Fix quota handling in aRFS flow expiration of mlx5 driver, from Eran
    Ben Elisha.

 4) Exit path handling fix in powerpc64 BPF JIT, from Daniel Borkmann.

 5) Use ptr_ring_consume_bh() in page pool code, from Tariq Toukan.

 6) Fix cached netdev name leak in nf_tables, from Florian Westphal.

 7) Fix memory leaks on chain rename, also from Florian Westphal.

 8) Several fixes to DCTCP congestion control ACK handling, from Yuchunk
    Cheng.

 9) Missing rcu_read_unlock() in CAIF protocol code, from Yue Haibing.

10) Fix link local address handling with VRF, from David Ahern.

11) Don't clobber 'err' on a successful call to __skb_linearize() in
    skb_segment(). From Eric Dumazet.

12) Fix vxlan fdb notification races, from Roopa Prabhu.

13) Hash UDP fragments consistently, from Paolo Abeni.

14) If TCP receives lots of out of order tiny packets, we do really
    silly stuff. Make the out-of-order queue ending more robust to this
    kind of behavior, from Eric Dumazet.

15) Don't leak netlink dump state in nf_tables, from Florian Westphal.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net: axienet: Fix double deregister of mdio
  qmi_wwan: fix interface number for DW5821e production firmware
  ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull
  bnx2x: Fix invalid memory access in rss hash config path.
  net/mlx4_core: Save the qpn from the input modifier in RST2INIT wrapper
  r8169: restore previous behavior to accept BIOS WoL settings
  cfg80211: never ignore user regulatory hint
  sock: fix sg page frag coalescing in sk_alloc_sg
  netfilter: nf_tables: move dumper state allocation into ->start
  tcp: add tcp_ooo_try_coalesce() helper
  tcp: call tcp_drop() from tcp_data_queue_ofo()
  tcp: detect malicious patterns in tcp_collapse_ofo_queue()
  tcp: avoid collapses in tcp_prune_queue() if possible
  tcp: free batches of packets in tcp_prune_ofo_queue()
  ip: hash fragments consistently
  ipv6: use fib6_info_hold_safe() when necessary
  can: xilinx_can: fix power management handling
  can: xilinx_can: fix incorrect clear of non-processed interrupts
  can: xilinx_can: fix RX overflow interrupt not being enabled
  can: xilinx_can: keep only 1-2 frames in TX FIFO to fix TX accounting
  ...

If the registration fails then mdio_unregister is called.
However at unbind the unregister ia attempted again resulting
in the below crash

[   73.544038] kernel BUG at drivers/net/phy/mdio_bus.c:415!
[   73.549362] Internal error: Oops - BUG: 0 [#1] SMP
[   73.554127] Modules linked in:
[   73.557168] CPU: 0 PID: 2249 Comm: sh Not tainted 4.14.0 #183
[   73.562895] Hardware name: xlnx,zynqmp (DT)
[   73.567062] task: ffffffc879e41180 task.stack: ffffff800cbe0000
[   73.572973] PC is at mdiobus_unregister+0x84/0x88
[   73.577656] LR is at axienet_mdio_teardown+0x18/0x30
[   73.582601] pc : [<ffffff80085fa4cc>] lr : [<ffffff8008616858>]
pstate: 20000145
[   73.589981] sp : ffffff800cbe3c30
[   73.593277] x29: ffffff800cbe3c30 x28: ffffffc879e41180
[   73.598573] x27: ffffff8008a21000 x26: 0000000000000040
[   73.603868] x25: 0000000000000124 x24: ffffffc879efe920
[   73.609164] x23: 0000000000000060 x22: ffffffc879e02000
[   73.614459] x21: ffffffc879e02800 x20: ffffffc87b0b8870
[   73.619754] x19: ffffffc879e02800 x18: 000000000000025d
[   73.625050] x17: 0000007f9a719ad0 x16: ffffff8008195bd8
[   73.630345] x15: 0000007f9a6b3d00 x14: 0000000000000010
[   73.635640] x13: 74656e7265687465 x12: 0000000000000030
[   73.640935] x11: 0000000000000030 x10: 0101010101010101
[   73.646231] x9 : 241f394f42533300 x8 : ffffffc8799f6e98
[   73.651526] x7 : ffffffc8799f6f18 x6 : ffffffc87b0ba318
[   73.656822] x5 : ffffffc87b0ba498 x4 : 0000000000000000
[   73.662117] x3 : 0000000000000000 x2 : 0000000000000008
[   73.667412] x1 : 0000000000000004 x0 : ffffffc8799f4000
[   73.672708] Process sh (pid: 2249, stack limit = 0xffffff800cbe0000)

Fix the same by making the bus NULL on unregister.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original mapping for the DW5821e was done using a development
version of the firmware. Confirmed with the vendor that the final
USB layout ends up exposing the QMI control/data ports in USB
config #1, interface #0, not in interface #1 (which is now a HID
interface).

T:  Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  2
P:  Vendor=413c ProdID=81d7 Rev=03.18
S:  Manufacturer=DELL
S:  Product=DW5821e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Fixes: e7e197ed ("qmi_wwan: add support for the Dell Wireless 5821e module")
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzbot reported a read beyond the end of the skb head when returning
IPV6_ORIGDSTADDR:

  BUG: KMSAN: kernel-infoleak in put_cmsg+0x5ef/0x860 net/core/scm.c:242
  CPU: 0 PID: 4501 Comm: syz-executor128 Not tainted 4.17.0+ #9
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
  Google 01/01/2011
  Call Trace:
    __dump_stack lib/dump_stack.c:77 [inline]
    dump_stack+0x185/0x1d0 lib/dump_stack.c:113
    kmsan_report+0x188/0x2a0 mm/kmsan/kmsan.c:1125
    kmsan_internal_check_memory+0x138/0x1f0 mm/kmsan/kmsan.c:1219
    kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1261
    copy_to_user include/linux/uaccess.h:184 [inline]
    put_cmsg+0x5ef/0x860 net/core/scm.c:242
    ip6_datagram_recv_specific_ctl+0x1cf3/0x1eb0 net/ipv6/datagram.c:719
    ip6_datagram_recv_ctl+0x41c/0x450 net/ipv6/datagram.c:733
    rawv6_recvmsg+0x10fb/0x1460 net/ipv6/raw.c:521
    [..]

This logic and its ipv4 counterpart read the destination port from
the packet at skb_transport_offset(skb) + 4.

With MSG_MORE and a local SOCK_RAW sender, syzbot was able to cook a
packet that stores headers exactly up to skb_transport_offset(skb) in
the head and the remainder in a frag.

Call pskb_may_pull before accessing the pointer to ensure that it lies
in skb head.

Link: http://lkml.kernel.org/r/CAF=yD-LEJwZj5a1-bAAj2Oy_hKmGygV6rsJ_WOrAYnv-fnayiQ@mail.gmail.com
Reported-by: syzbot+9adb4b567003cac781f0@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rx hash/filter table configuration uses rss_conf_obj to configure filters
in the hardware. This object is initialized only when the interface is
brought up.
This patch adds driver changes to configure rss params only when the device
is in opened state. In port disabled case, the config will be cached in the
driver structure which will be applied in the successive load path.

Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function mlx4_RST2INIT_QP_wrapper saved the qp number passed in the qp
context, rather than the one passed in the input modifier.

However, the qp number in the qp context is not defined as a
required parameter by the FW. Therefore, drivers may choose to not
specify the qp number in the qp context for the reset-to-init transition.

Thus, we must save the qp number passed in the command input modifier --
which is always present. (This saved qp number is used as the input
modifier for command 2RST_QP when a slave's qp's are destroyed).

Fixes: c82e9aa0 ("mlx4_core: resource tracking for HCA resources used by guests")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 7edf6d31 tried to resolve an inconsistency (BIOS WoL
settings are accepted, but device isn't wakeup-enabled) resulting
from a previous broken-BIOS workaround by making disabled WoL the
default.
This however had some side effects, most likely due to a broken BIOS
some systems don't properly resume from suspend when the MagicPacket
WoL bit isn't set in the chip, see
https://bugzilla.kernel.org/show_bug.cgi?id=200195
Therefore restore the WoL behavior from 4.16.
Reported-by: Albert Astals Cid <aacid@kde.org>
Fixes: 7edf6d31 ("r8169: disable WOL per default")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull s390 fix from Martin Schwidefsky.

Guenter Roeck reports that the s390 allmodconfig build fails because of
a gcc plugin problem.  The fix won't be in-tree until 4.19, so for now
disable the gcc plugins on s390.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390: disable gcc plugins

Including asm/cacheflush.h first results in the following build error
when trying to build sparc32:allmodconfig, because 'struct page' has not
been declared, and the function declaration ends up creating a separate
(private) declaration of struct page (as a result of function arguments
being in the scope of the function declaration and definition, not in
global scope).

The C scoping rules do not just affect variable visibility, they also
affect type declaration visibility.

The end result is that when the actual call site is seen in
<linux/highmem.h>, the 'struct page' type in the caller is not the same
'struct page' that the function was declared with, resulting in:

  In file included from arch/sparc/include/asm/page.h:10:0,
                   ...
                   from drivers/staging/media/omap4iss/iss_video.c:15:
  include/linux/highmem.h: In function 'clear_user_highpage':
  include/linux/highmem.h:137:31: error:
	passing argument 1 of 'sparc_flush_page_to_ram' from incompatible
	pointer type

Include generic includes files first to fix the problem.

Fixes: fc96d58c ("[media] v4l: omap4iss: Add support for OMAP4 camera interface - Video devices")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Added explanation of C scope rules - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Make sure we don't go over the maximum jump stack boundary,
   from Taehee Yoo.

2) Missing rcu_barrier() in hash and rbtree sets, also from Taehee.

3) Missing check to nul-node in rbtree timeout routine, from Taehee.

4) Use dev->name from flowtable to fix a memleak, from Florian.

5) Oneliner to free flowtable object on removal, from Florian.

6) Memleak in chain rename transaction, again from Florian.

7) Don't allow two chains to use the same name in the same
   transaction, from Florian.

8) handle DCCP SYNC/SYNCACK as invalid, this triggers an
   uninitialized timer in conntrack reported by syzbot, from Florian.

9) Fix leak in case netlink_dump_start() fails, from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-07-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Only a few fixes:
 * always keep regulatory user hint
 * add missing break statement in station flags parsing
 * fix non-linear SKBs in port-control-over-nl80211
 * reconfigure VLAN stations during HW restart
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently user regulatory hint is ignored if all wiphys
in the system are self managed. But the hint is not ignored
if there is no wiphy in the system. This affects the global
regulatory setting. Global regulatory setting needs to be
maintained so that it can be applied to a new wiphy entering
the system. Therefore, do not ignore user regulatory setting
even if all wiphys in the system are self managed.
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The s390 build currently fails with the latent entropy plugin:

arch/s390/kernel/als.o: In function `verify_facilities':
als.c:(.init.text+0x24): undefined reference to `latent_entropy'
als.c:(.init.text+0xae): undefined reference to `latent_entropy'
make[3]: *** [arch/s390/boot/compressed/vmlinux] Error 1
make[2]: *** [arch/s390/boot/compressed/vmlinux] Error 2
make[1]: *** [bzImage] Error 2

This will be fixed with the early boot rework from Vasily, which
is planned for the 4.19 merge window.

For 4.18 the simplest solution is to disable the gcc plugins and
reenable them after the early boot rework is upstream.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Current sg coalescing logic in sk_alloc_sg() (latter is used by tls and
sockmap) is not quite correct in that we do fetch the previous sg entry,
however the subsequent check whether the refilled page frag from the
socket is still the same as from the last entry with prior offset and
length matching the start of the current buffer is comparing always the
first sg list entry instead of the prior one.

Fixes: 3c4d7559 ("tls: kernel TLS support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shaochun Chen points out we leak dumper filter state allocations
stored in dump_control->data in case there is an error before netlink sets
cb_running (after which ->done will be called at some point).

In order to fix this, add .start functions and do the allocations
there.

->done is going to clean up, and in case error occurs before
->start invocation no cleanups need to be done anymore.
Reported-by: shaochun chen <cscnull@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Eric Dumazet says:

====================
Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet.

With tcp_rmem[2] default of 6MB, the ooo queue could
contain ~7000 nodes.

This patch series makes sure we cut cpu cycles enough to
render the attack not critical.

We might in the future go further, like disconnecting
or black-holing proven malicious flows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case skb in out_or_order_queue is the result of
multiple skbs coalescing, we would like to get a proper gso_segs
counter tracking, so that future tcp_drop() can report an accurate
number.

I chose to not implement this tracking for skbs in receive queue,
since they are not dropped, unless socket is disconnected.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to be able to give better diagnostics and detect
malicious traffic, we need to have better sk->sk_drops tracking.

Fixes: 9f5afeae ("tcp: use an RB tree for ooo receive queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case an attacker feeds tiny packets completely out of order,
tcp_collapse_ofo_queue() might scan the whole rb-tree, performing
expensive copies, but not changing socket memory usage at all.

1) Do not attempt to collapse tiny skbs.
2) Add logic to exit early when too many tiny skbs are detected.

We prefer not doing aggressive collapsing (which copies packets)
for pathological flows, and revert to tcp_prune_ofo_queue() which
will be less expensive.

In the future, we might add the possibility of terminating flows
that are proven to be malicious.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Right after a TCP flow is created, receiving tiny out of order
packets allways hit the condition :

if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf)
	tcp_clamp_window(sk);

tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc
(guarded by tcp_rmem[2])

Calling tcp_collapse_ofo_queue() in this case is not useful,
and offers a O(N^2) surface attack to malicious peers.

Better not attempt anything before full queue capacity is reached,
forcing attacker to spend lots of resource and allow us to more
easily detect the abuse.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Juha-Matti Tilli reported that malicious peers could inject tiny
packets in out_of_order_queue, forcing very expensive calls
to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for
every incoming packet. out_of_order_queue rb-tree can contain
thousands of nodes, iterating over all of them is not nice.

Before linux-4.9, we would have pruned all packets in ofo_queue
in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs
truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB.

Since we plan to increase tcp_rmem[2] in the future to cope with
modern BDP, can not revert to the old behavior, without great pain.

Strategy taken in this patch is to purge ~12.5 % of the queue capacity.

Fixes: 36a6503f ("tcp: refine tcp_prune_ofo_queue() to not drop all packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Juha-Matti Tilli <juha-matti.tilli@iki.fi>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The skb hash for locally generated ip[v6] fragments belonging
to the same datagram can vary in several circumstances:
* for connected UDP[v6] sockets, the first fragment get its hash
  via set_owner_w()/skb_set_hash_from_sk()
* for unconnected IPv6 UDPv6 sockets, the first fragment can get
  its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if
  auto_flowlabel is enabled

For the following frags the hash is usually computed via
skb_get_hash().
The above can cause OoO for unconnected IPv6 UDPv6 socket: in that
scenario the egress tx queue can be selected on a per packet basis
via the skb hash.
It may also fool flow-oriented schedulers to place fragments belonging
to the same datagram in different flows.

Fix the issue by copying the skb hash from the head frag into
the others at fragmentation time.

Before this commit:
perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8"
netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n &
perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1
perf script
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0

After this commit:
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0
probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0

Fixes: b73c3d0e ("net: Save TX flow hash in sock and set in skbuf on xmit")
Fixes: 67800f9b ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the code path where only rcu read lock is held, e.g. in the route
lookup code path, it is not safe to directly call fib6_info_hold()
because the fib6_info may already have been deleted but still exists
in the rcu grace period. Holding reference to it could cause double
free and crash the kernel.

This patch adds a new function fib6_info_hold_safe() and replace
fib6_info_hold() in all necessary places.

Syzbot reported 3 crash traces because of this. One of them is:
8021q: adding VLAN 0 to HW filter on device team0
IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready
dst_release: dst:(____ptrval____) refcnt:-1
dst_release: dst:(____ptrval____) refcnt:-2
WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 dst_hold include/net/dst.h:239 [inline]
WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204
dst_release: dst:(____ptrval____) refcnt:-1
Kernel panic - not syncing: panic_on_warn set ...

CPU: 1 PID: 4845 Comm: syz-executor493 Not tainted 4.18.0-rc3+ #10
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
 panic+0x238/0x4e7 kernel/panic.c:184
dst_release: dst:(____ptrval____) refcnt:-2
dst_release: dst:(____ptrval____) refcnt:-3
 __warn.cold.8+0x163/0x1ba kernel/panic.c:536
dst_release: dst:(____ptrval____) refcnt:-4
 report_bug+0x252/0x2d0 lib/bug.c:186
 fixup_bug arch/x86/kernel/traps.c:178 [inline]
 do_error_trap+0x1fc/0x4d0 arch/x86/kernel/traps.c:296
dst_release: dst:(____ptrval____) refcnt:-5
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:316
 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:992
RIP: 0010:dst_hold include/net/dst.h:239 [inline]
RIP: 0010:ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204
Code: c1 ed 03 89 9d 18 ff ff ff 48 b8 00 00 00 00 00 fc ff df 41 c6 44 05 00 f8 e9 2d 01 00 00 4c 8b a5 c8 fe ff ff e8 1a f6 e6 fa <0f> 0b e9 6a fc ff ff e8 0e f6 e6 fa 48 8b 85 d0 fe ff ff 48 8d 78
RSP: 0018:ffff8801a8fcf178 EFLAGS: 00010293
RAX: ffff8801a8eba5c0 RBX: 0000000000000000 RCX: ffffffff869511e6
RDX: 0000000000000000 RSI: ffffffff869515b6 RDI: 0000000000000005
RBP: ffff8801a8fcf2c8 R08: ffff8801a8eba5c0 R09: ffffed0035ac8338
R10: ffffed0035ac8338 R11: ffff8801ad6419c3 R12: ffff8801a8fcf720
R13: ffff8801a8fcf6a0 R14: ffff8801ad6419c0 R15: ffff8801ad641980
 ip6_make_skb+0x2c8/0x600 net/ipv6/ip6_output.c:1768
 udpv6_sendmsg+0x2c90/0x35f0 net/ipv6/udp.c:1376
 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798
 sock_sendmsg_nosec net/socket.c:641 [inline]
 sock_sendmsg+0xd5/0x120 net/socket.c:651
 ___sys_sendmsg+0x51d/0x930 net/socket.c:2125
 __sys_sendmmsg+0x240/0x6f0 net/socket.c:2220
 __do_sys_sendmmsg net/socket.c:2249 [inline]
 __se_sys_sendmmsg net/socket.c:2246 [inline]
 __x64_sys_sendmmsg+0x9d/0x100 net/socket.c:2246
 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x446ba9
Code: e8 cc bb 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fb39a469da8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133
RAX: ffffffffffffffda RBX: 00000000006dcc54 RCX: 0000000000446ba9
RDX: 00000000000000b8 RSI: 0000000020001b00 RDI: 0000000000000003
RBP: 00000000006dcc50 R08: 00007fb39a46a700 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 45c828efc7a64843
R13: e6eeb815b9d8a477 R14: 5068caf6f713c6fc R15: 0000000000000001
Dumping ftrace buffer:
   (ftrace buffer empty)
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: syzbot+902e2a1bcd4f7808cef5@syzkaller.appspotmail.com
Reported-by: syzbot+8ae62d67f647abeeceb9@syzkaller.appspotmail.com
Reported-by: syzbot+3f08feb14086930677d0@syzkaller.appspotmail.com
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.18-20180723' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2018-07-23

this is a pull request of 12 patches for net/master.

The patch by Stephane Grosjean for the peak_canfd CAN driver fixes a problem
with older firmware. The next patch is by Roman Fietze and fixes the setup of
the CCCR register in the m_can driver. Nicholas Mc Guire's patch for the
mpc5xxx_can driver adds missing error checking. The two patches by Faiz Abbas
fix the runtime resume and clean up the probe function in the m_can driver. The
last 7 patches by Anssi Hannula fix several problem in the xilinx_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are several issues with the suspend/resume handling code of the
driver:

- The device is attached and detached in the runtime_suspend() and
  runtime_resume() callbacks if the interface is running. However,
  during xcan_chip_start() the interface is considered running,
  causing the resume handler to incorrectly call netif_start_queue()
  at the beginning of xcan_chip_start(), and on xcan_chip_start() error
  return the suspend handler detaches the device leaving the user
  unable to bring-up the device anymore.

- The device is not brought properly up on system resume. A reset is
  done and the code tries to determine the bus state after that.
  However, after reset the device is always in Configuration mode
  (down), so the state checking code does not make sense and
  communication will also not work.

- The suspend callback tries to set the device to sleep mode (low-power
  mode which monitors the bus and brings the device back to normal mode
  on activity), but then immediately disables the clocks (possibly
  before the device reaches the sleep mode), which does not make sense
  to me. If a clean shutdown is wanted before disabling clocks, we can
  just bring it down completely instead of only sleep mode.

Reorganize the PM code so that only the clock logic remains in the
runtime PM callbacks and the system PM callbacks contain the device
bring-up/down logic. This makes calling the runtime PM callbacks during
e.g. xcan_chip_start() safe.

The system PM callbacks now simply call common code to start/stop the
HW if the interface was running, replacing the broken code from before.

xcan_chip_stop() is updated to use the common reset code so that it will
wait for the reset to complete. Reset also disables all interrupts so do
not do that separately.

Also, the device_may_wakeup() checks are removed as the driver does not
have wakeup support.

Tested on Zynq-7000 integrated CAN.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of
them is asserted. This does not take into account that some of them
could have been asserted between interrupt status read and interrupt
clear, therefore clearing them without handling them.

Fix the code to only clear those interrupts that it knows are asserted
and therefore going to be processed in xcan_err_interrupt().

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt()
processes it. This means that an RX overflow interrupt will only be
processed when another interrupt gets asserted (e.g. for RX/TX).

Fix that by enabling the RXOFLW interrupt.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The xilinx_can driver assumes that the TXOK interrupt only clears after
it has been acknowledged as many times as there have been successfully
sent frames.

However, the documentation does not mention such behavior, instead
saying just that the interrupt is cleared when the clear bit is set.

Similarly, testing seems to also suggest that it is immediately cleared
regardless of the amount of frames having been sent. Performing some
heavy TX load and then going back to idle has the tx_head drifting
further away from tx_tail over time, steadily reducing the amount of
frames the driver keeps in the TX FIFO (but not to zero, as the TXOK
interrupt always frees up space for 1 frame from the driver's
perspective, so frames continue to be sent) and delaying the local echo
frames.

The TX FIFO tracking is also otherwise buggy as it does not account for
TX FIFO being cleared after software resets, causing
  BUG!, TX FIFO full when queue awake!
messages to be output.

There does not seem to be any way to accurately track the state of the
TX FIFO for local echo support while using the full TX FIFO.

The Zynq version of the HW (but not the soft-AXI version) has watermark
programming support and with it an additional TX-FIFO-empty interrupt
bit.

Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI
and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used
to detect whether 1 or 2 frames have been sent at interrupt processing
time.

Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode
was also tested.

An alternative way to solve this would be to drop local echo support but
keep using the full TX FIFO.

v2: Add FIFO space check before TX queue wake with locking to
synchronize with queue stop. This avoids waking the queue when xmit()
had just filled it.

v3: Keep local echo support and reduce the amount of frames in FIFO
instead as suggested by Marc Kleine-Budde.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The xilinx_can driver contains no mechanism for propagating recovery
from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE.

Add such a mechanism by factoring the handling of
XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of
xcan_err_interrupt and checking for recovery after RX and TX if the
interface is in one of those states.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If the device gets into a state where RXNEMP (RX FIFO not empty)
interrupt is asserted without RXOK (new frame received successfully)
interrupt being asserted, xcan_rx_poll() will continue to try to clear
RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is
not empty, the interrupt will not be cleared and napi_schedule() will
just be called again.

This situation can occur when:

(a) xcan_rx() returns without reading RX FIFO due to an error condition.
The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear
due to a frame still being in the FIFO. The frame will never be read
from the FIFO as RXOK is no longer set.

(b) A frame is received between xcan_rx_poll() reading interrupt status
and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain
set as the new message is still in the FIFO.

I'm able to trigger case (b) by flooding the bus with frames under load.

There does not seem to be any benefit in using both RXNEMP and RXOK in
the way the driver does, and the polling example in the reference manual
(UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either
RXOK or RXNEMP can be used for detecting incoming messages.

Fix the issue and simplify the RX processing by only using RXNEMP
without RXOK.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The xilinx_can driver performs a software reset when an RX overrun is
detected. This causes the device to enter Configuration mode where no
messages are received or transmitted.

The documentation does not mention any need to perform a reset on an RX
overrun, and testing by inducing an RX overflow also indicated that the
device continues to work just fine without a reset.

Remove the software reset.

Tested with the integrated CAN on Zynq-7000 SoC.

Fixes: b1201e44 ("can: xilinx CAN controller support")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

MCAN message ram should only be accessed once clocks are enabled.
Therefore, move the call to parse/init the message ram to after
clocks are enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>