- 10 Jul, 2024 1 commit
-
-
Mitul Golani authored
The dispcnlunit1_cp_xosc_clk should be de-asserted in display off and only asserted in display on. As part of this workaround, Display driver shall execute set-reset sequence at the end of the initialize sequence to ensure clk does not remain active in display OFF. --v2: - Rebase. --v3: - Correct HSD number in commit message. --v4: - Reformat commit message. - Use intel_de_rmw instead of intel_de_write --v5: - Build Fixes. WA: 15013987218 Signed-off-by:
Mitul Golani <mitulkumar.ajitkumar.golani@intel.com> Reviewed-by:
Nemesa Garg <nemesa.garg@intel.com> Reviewed-by:
Suraj Kandpal <suraj.kandpal@intel.com> Signed-off-by:
-
- 09 Jul, 2024 1 commit
-
-
Mitul Golani authored
Add new member to struct intel_dp to cache support of Adaptive Sync SDP capabilities and use it whenever required to avoid HW access to read capability during each atomic commit. -v2: - Squash both the patches Signed-off-by:
Arun R Murthy <arun.r.murthy@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240704082638.2302092-2-mitulkumar.ajitkumar.golani@intel.comSigned-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com>
-
- 01 Jul, 2024 1 commit
-
-
Gustavo Sousa authored
Starting with Xe_LPD+, although FIA is still used to readout Type-C pin assignment, part of Type-C support is moved to PICA and programming PORT_TX_DFLEXDPMLE1(*) registers is not applicable anymore like it was for previous display IPs (e.g. see BSpec 49190). v2: - Mention Bspec 49190 as a reference of instructions for previous IPs. (Shekhar Chauhan) - s/Xe_LPDP/Xe_LPD+/ in the commit message. (Matt Roper) - Update commit message to be more accurate to the changes in the IP. (Imre Deak) Bspec: 65750, 65448 Reviewed-by:Shekhar Chauhan <shekhar.chauhan@intel.com> Reviewed-by:
Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240625202652.315936-1-gustavo.sousa@intel.comSigned-off-by:
Gustavo Sousa <gustavo.sousa@intel.com>
-
- 28 Jun, 2024 1 commit
-
-
Imre Deak authored
In TBT-alt mode the driver doesn't program the PHY's PLL, which is handled instead by Thunderbolt driver/FW components, hence the PLL's HW vs. SW state verification should be skipped. During HW readout set a flag in the PLL state if the port was at the moment in TBT-alt mode and skip the verification of PLL parameters in this case. Fixes: 45fe957a ("drm/i915/display: Add compare config for MTL+ platforms") Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11258 Cc: Mika Kahola <mika.kahola@intel.com> Reviewed-by:
Mika Kahola <mika.kahola@intel.com> Signed-off-by:
-
- 27 Jun, 2024 1 commit
-
-
Ville Syrjälä authored
DSB_STATUS bit 16 is supposed to be a sticky bit informing us whether the DSB was idle or not when the pipe's delayed vblank (when double buffered registers latch) occurred. Unfortunately it turns out this is a level triggred signal, ie. the bit will be set whenever the DSB is busy during the scanline window between start of delayed vblank and vtotal. Try to document that fact by renaming the bit. Sadly this also thwarts my plan to use this bit to sanity check that the (to be introduced) DSB based vblank evasion did its job correctly. That would require an edge triggered signal instead. So looks like we'll have to rely mostly on luck instead :( Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240611133344.30673-12-ville.syrjala@linux.intel.comReviewed-by:
Jani Nikula <jani.nikula@intel.com>
-
- 26 Jun, 2024 1 commit
-
-
Imre Deak authored
For MTL+ platforms we use PICA chips for Type-C support and hence mg programming is not needed. Fixes issue with drm warn of TC port not being in legacy mode. Cc: stable@vger.kernel.org Signed-off-by:
-
- 25 Jun, 2024 11 commits
-
-
Jouni Högander authored
There are couple of bits in PSR2_CTL which needs to be written in case of eDP Panel Replay Bspec: 68920 v2: use boolean instead of assuming eDP Panel Replay mean Early Transport Signed-off-by:
Jouni Högander <jouni.hogander@intel.com> Reviewed-by:
Animesh Manna <animesh.manna@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-12-jouni.hogander@intel.com
-
Jouni Högander authored
Move Early Transport validity check to be performed for Panel Replay as well and use Early Transport for eDP Panel Replay always. v2:set crtc_state->enable_psr2_su_region_et directly (not in if block) Signed-off-by:
-
Jouni Högander authored
Scanline indication needs to be checked and configure for both PSR2 and Panel Replay Selective Update. Move this check to intel_sel_update_config_valid. Signed-off-by:
-
Jouni Högander authored
eDP1.5 support ALPM with Panel Replay as well. We need to check ALPM related things for Panel Replay as well. Bspec: 68920 v5: - instead of using crtc_state->has_panel_replay provide aux_less flag v4: - do not move _compute_psr2_sdp_prior_scanline_indication - move ALPM related checks to separate function v3: move vblank check as well v2: do not move Vblank >= PSR2_CTL Block Count Number maximum line count check Signed-off-by: -
Jouni Högander authored
Intel_alpm_compute_params doesn't change crtc_state. Let's convert it as const. Signed-off-by:
-
Jouni Högander authored
Take into account in Panel Replay compute config that HW will not allow PR on eDP when HDCP enabled. v2: add debug message to print out why Panel Replay is not possible Signed-off-by:
-
Jouni Högander authored
Take into account that 128b/132b Panel Replay is not supported on eDP. Bspec: 68920 v2: - make crtc_state as const - add debug message to print out why Panel Replay is not possible Signed-off-by:
-
Jouni Högander authored
Our HW doesn't support panel replay without Early Transport on eDP. Bspec: 68920 Signed-off-by:
-
Jouni Högander authored
eDP1.5 allows Panel Replay on eDP as well. Take this into account when enabling sink PSR/Panel Replay. Write also PANEL_REPLAY_CONFIG2 register accordingly. v3: - set DP_PANEL_REPLAY_CRC_VERIFICATION in PANEL_REPLAY_CONFIG2 - PANEL_REPLAY_CONFIG2 is available in DP2.1 as well v2: do not configure ALPM for DP2.0 Panel Replay Signed-off-by:
-
Jouni Högander authored
Display version >= 20 support eDP 1.5. Inform Panel Replay source support on eDP for display version >= 20. Bspec: 68920 Signed-off-by:
-
Jouni Högander authored
Our HW doesn't support Panel Replay without AUX_LESS ALPM on eDP. Check panel support for this and prevent eDP panel replay if it doesn't exits. Bspec: 68920 v3: remove excessive parens v2: use intel_alpm_aux_less_wake_supported Signed-off-by:
-
- 24 Jun, 2024 14 commits
-
-
Maarten Lankhorst authored
In case of legacy cursor update, the cursor VMA needs to be unpinned only after vblank. This exceeds the lifetime of the whole atomic commit. Any trick I attempted to keep the atomic commit alive didn't work, as drm_atomic_helper_setup_commit() force throttles on any old commit that wasn't cleaned up. The only option remaining is to remove the plane from the atomic commit, and use the same path as the legacy cursor update to clean the state after vblank. Changes since previous version: - Call the memset for plane state immediately when scheduling vblank, this prevents a use-after-free in cursor cleanup. Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Reviewed-by:
Uma Shankar <uma.shankar@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240522053341.137592-4-maarten.lankhorst@linux.intel.com
-
Ville Syrjälä authored
The cursor hardware only does sync updates, and thus the hardware will be scanning out from the old fb until the next start of vblank. So in order to make the legacy cursor fastpath actually safe we should not unpin the old fb until we're sure the hardware has ceased accessing it. The simplest approach is to just use a vblank work here to do the delayed unpin. Not 100% sure it's a good idea to put this onto the same high priority vblank worker as eg. our timing critical gamma updates. But let's keep it simple for now, and it we later discover that this is causing problems we can think about adding a lower priority worker for such things. This patch is slightly reworked by Maarten Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
-
Maarten Lankhorst authored
In some cases we want to flush all vblank work, right before vblank_off for example. Add a simple function to make this possible. Check that both pending_work and running work are empty when flushing. Co-Developed-by:
Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com> Signed-off-by:
-
Ville Syrjälä authored
I don't think the display hardware really has such chroma plane tile row alignment requirements as outlined in commit d156135e ("drm/i915/tgl: Make sure a semiplanar UV plane is tile row size aligned") Bspec had the same exact thing to say about earlier hardware as well, but we never cared and things work just fine. The one thing mentioned in that commit that is definitely true however is the fence alignment issue. But we don't deal with that on earlier hardware either. We do have code to deal with that issue for the first color plane, but not the chroma planes. So I think if we did want to check this more extensively we should do it in the same places where we already check the first color plane (namely convert_plane_offset_to_xy() and intel_fb_bo_framebuffer_init()). Reviewed-by:
-
Ville Syrjälä authored
Currently we still use the SKL+ PLANE_SURF alignment even for TGL+ even though the hardware no longer needs it. Introduce a separate tgl_plane_min_alignment() and update it to more accurately reflect the hardware requirements. v2: Don't screw up DPT+semiplanar 2MiB alignment Reviewed-by:
-
Ville Syrjälä authored
Now that all pre-skl platforms have their own .min_alignment() functions the remainder of intel_surf_alignment() can be hoisted into skl_univerals_plane.c (and renamed appropriately). Reviewed-by:
-
Ville Syrjälä authored
Extract the necessary chunks from intel_surf_alignment() into per-platform variants for all pre-skl primary/sprite planes. Reviewed-by:
-
Ville Syrjälä authored
Split intel_cursor_alignment() into per-platform variants. Reviewed-by:
-
Ville Syrjälä authored
Different planes could have different alignment requirements even for the same format/modifier. Collect the alignment requirements across all planes capable of scanning out the fb such that the alignment is satisfactory to all those planes. So far this was sort of handled by making sure intel_surf_alignment() declares the superset of all planes' alignment requirements, but maintaining that manually is annoying. So we're going to move towards each plane declaring only its own requirements, and thus we need code to generate the superset. v2: Drop the borked per-plane vma optimization (Imre) Assert that the plane's declared alignment is POT (Imre) Signed-off-by: -
Ville Syrjälä authored
Different hardware generations have different scanout alignment requirements. Introduce a new vfunc that will allow us to make that distinction without horrible if-ladders. For now we directly plug in the existing intel_surf_alignment() and intel_cursor_alignment() functions. For fbdev we (temporarily) introduce intel_fbdev_min_alignment() that simply queries the alignment from the primary plane of the first crtc. TODO: someone will need to fix xe's alignment handling Reviewed-by:
-
Ville Syrjälä authored
Export drm_plane_has_format() so that drivers can use it. v2: add kerneldoc Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Daniel Stone <daniels@collabora.com> Acked-by:
Thomas Zimmermann <tzimmermann@suse.de>
-
Ville Syrjälä authored
Rename drm_plane_check_pixel_format() to drm_plane_has_format() and change the return type accordingly. Allows one to write more natural code. Also matches drm_any_plane_has_format() better. Reviewed-by:
-
Mitul Golani authored
Consider adjusted_pixel_rate to be a u64 to match the return type of mul_u32_u32() and avoid any compiler dependency for do_div. Fixes: 1676ecd3 ("drm/i915: Compute CMRR and calculate vtotal") Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Suraj Kandpal <suraj.kandpal@intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Nathan Chancellor <nathan@kernel.org> Cc: intel-xe@lists.freedesktop.org Reported-by:
Nathan Chancellor <nathan@kernel.org> Closes: https://lore.kernel.org/r/20240619154207.GA1125704@thelio-3990XSigned-off-by:
-
Jouni Högander authored
Setting DP_PSR_SU_REGION_SCANLINE_CAPTURE (Selective Update Region Scan Line Capture Indication in spec) bit was dropped when psr_enable_sink was split to _psr_enable_sink and _panel_replay_enable_sink. Add setting it back. Fixes: 32f0045f ("drm/i915/psr: Split enabling sink for PSR and Panel Replay") Signed-off-by:
-
- 20 Jun, 2024 9 commits
-
-
Imre Deak authored
Use the suspend encoders helper which is also used by the i915 driver. This fixes an issue in the xe driver where the encoder suspend_complete() hook is not called and was an overlook when this hook was added in commit b61fad5f ("drm/i915/tc: Call TypeC port flush_work/cleanup without modeset locks held") for i915, but not added to the xe driver (which was still in a separate source tree at the above point). v2: Fix checkpatch warn in commit log. (Rodrigo) Reviewed-by:
-
Imre Deak authored
Pass intel_display to the encoder suspend/shutdown helpers instead of drm_i915_private for better isolation. v2: Pass intel_display to HAS_DISPLAY() as well, update commit log accordingly. (Jani) Cc: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> # v1 Reviewed-by: -
Imre Deak authored
Move the encoder suspend/shutdown helpers to intel_encoder.c, this being the logical place for encoder functions. This also allows sharing the above helpers with the xe driver, done in a follow-up patch. While at it rename the functions using the usual intel_encoder prefix and in the functions rename the dev_priv parameter to i915. v2: Remove extra w/s in the include section. (Jani) Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> # v1 Reviewed-by:
-
Ville Syrjälä authored
The ATS faults have something to do with some new iommu stuff on mtl+. Document that the relevant DSB interrupt bits aren't valid for earlier platforms. Signed-off-by:
-
Ville Syrjälä authored
intel_crtc.c doens't need intel_dsb.h so don't include it. Signed-off-by:
-
Ville Syrjälä authored
As we extend the use of DSB for critical pipe/plane register programming, it'll be nice to have an escape valve at hand, in case things go very poorly. To that end, add a i915.enable_dsb modparam by which we can force the driver to take the pure mmio path instead. v2: Use 0400 permissions for the actual modparam (Jani) Signed-off-by:
-
Ville Syrjälä authored
The future direction will be to mainly use intel_display rather than i915 in the display code. Start on that path for the DSB code. Signed-off-by:
-
Ville Syrjälä authored
The DSB code will need to examine both the old and new crtc states. Pass in the whole atomic state so we can dig up what we need. Signed-off-by:
-
Ville Syrjälä authored
We'll have need to examine both the old and new crtc states in intel_color_prepare_commit(), so let's just pass in the whole atomic state. Signed-off-by:
-
