This switches the code using a local remapping of the
system controller to enable the U300 board to be
self-powered over to making the U300-specific syscon
compatible with the MFD generic syscon driver, selecting
the generic syscon driver, and augmenting the board
power code to pick the regmap and manipulate the syscon
from the regmap side of things.

Cc: Dong Aisheng <dong.aisheng@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Enable MMC_UNSAFE_RESUME to be accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.

ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In the past we controlled the selection of DMA for a certain
host by a boolean switch in the platform data. Currently
there is no way to enable DMA on a PL022 probed from the
device tree. Let's default to trying to obtain DMA channels
in the DT case, and then we can always fail (and thus fall
back to PIO mode).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This deletes the dependency on any platform data for
the COH901 pin controller. There is only one user in the
kernel, and if we at some point want to support more
variants, they shall provide their variant info through
the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the last of the U300 clocks to being probed from
the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This moves the slow, fast, AHB bridge and "rest" clocks on
the U300 system controller over to registration from the
device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We have used the default clock associated with the block
for a long time, only heuristics in the clock system has
made this work anyway. This needs to be done away with as
we start probing this driver and its clocks exclusively
from the device tree.
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the fixed and fixed-factor clocks in the U300
platform to register themselves from the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that the core file is the only one actually using any
of the base addresses, we can delete that header and move
the base address definitions into the one and only core
file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Two files remain in <mach/*> for U300: timex.h and
uncompress.h. The former is done away with by using
defaults, the latter is unused in multiplatform.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that we removed our dependency on <mach/*> the U300
can be converted to mutliplatform. Remove the invalid restriction
that U300 would not support AUTO_ZRELADDR (it does) and update
the defconfig in the process.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This register base file is now only used in the machine
itself so move it down into mach-u300.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

All IRQs are now obtained from the device tree, and this file
is unused, so delete it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This file is now unused and can be deleted.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of the <mach/syscon.h> header as a prerequisite for
multiplatform support. Do this by pushing the registers down
to their respective drivers and deleting the unused remainder.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This rids the dependency to <mach/hardware.h> (which is an
implicit dependency to <mach/u300-regs.h>) from the U300
debug macro. Take this opportunity to update the file
header.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This moves the U300 debug macro to the debug headers to
make way for multiplatform support.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We have now transferred all the U300 peripherals to the device
tree, so we just select USE_OF, and delete all static board data,
then require that this platform shall be booted using the device
tree and nothing else.

This gets rid of the MMCI (PL180), PL022, and serial PL011
platform data entries and more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This probes the U300 dummy-spichip from the device tree
and adds the apropriate node to the tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.

Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds DMA channel assignments to the MMC/SD-controller
and the two UARTs already in the U300 device tree, as we
have now defined a way to obtain DMA channels from the
device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for probing the COH 901 318 DMA controller
and channels from the device tree.

Contains portions of a sketch patch from Arnd Bergmann.

Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for setting up the board power from the
device tree on the U300. We use a board-specific node in the
device tree for the S365 board and bind a regulator for the
board power to this node.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the COH 901 331 RTC to the U300 device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This add devicetree probe support to the COH 901 331 RTC
driver.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the COH 901 327 watchdog to the U300 device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for probing the COH 901 327 watchdog from
the device tree and also adds associated bindings.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the two I2C busses to the device tree so these
probe properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds device tree support for the ST DDC I2C driver known
as "stu300" in the kernel tree.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This register the most basic peripherals and makes the
U300 boot to prompt from a device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes it possible to probe the COH901 pinctrl driver from
the device tree, and assigned the device tree node in the
gpio_chip so we can look up cross-references from the device
tree. Start grabbing the per-port (bank) IRQs by index instead
of by name so we don't have to look up the IRQs by name going
forward.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a simple device tree compat string for the U300 pin
controller. The base address is already passed properly as
a resource and everything works fine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds device tree support for the U300 timer, by making
the memory base offset and IRQ dynamically assigned, then
optionally looking them up from the device tree.

Since the timer needs to be registered before any platform
devices are created, we will go into the device tree and look
up the "/timer@c0014000" node and read our base address and
IRQ from there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The U300 can support timer-based delays, so implement this.
Skips past jiffy calibration.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>