* pm-cpufreq:
  intel_pstate: Take core C0 time into account for core busy calculation

* acpi-pci-hotplug:
  ACPI / hotplug / PCI: Fix bridge removal race vs dock events
  ACPI / hotplug / PCI: Fix bridge removal race in handle_hotplug_event()
  ACPI / hotplug / PCI: Scan root bus under the PCI rescan-remove lock
  ACPI / hotplug / PCI: Move PCI rescan-remove locking to hotplug_event()
  ACPI / hotplug / PCI: Remove entries from bus->devices in reverse order

* acpi-hotplug:
  ACPI / hotplug: Fix panic on eject to ejected device

When an eject request is sent to an ejected ACPI device, the following
panic occurs:

 ACPI: \_SB_.SCK3.CPU3: ACPI_NOTIFY_EJECT_REQUEST event
 BUG: unable to handle kernel NULL pointer dereference at 0000000000000070
 IP: [<ffffffff813a7cfe>] acpi_device_hotplug+0x10b/0x33b
	:
 Call Trace:
 [<ffffffff813a24da>] acpi_hotplug_work_fn+0x1c/0x27
 [<ffffffff8109cbe5>] process_one_work+0x175/0x430
 [<ffffffff8109d7db>] worker_thread+0x11b/0x3a0

This is becase device->handler is NULL in acpi_device_hotplug().
This case was used to fail in acpi_hotplug_notify_cb() as the target
had no acpi_deivce.  However, acpi_device now exists after ejection.

Added a check to verify if acpi_device->handler is valid for an
eject request in acpi_hotplug_notify_cb().  Note that handler passed
from an argument is still valid while acpi_device->handler is NULL.

Fixes: 202317a5 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Take non-idle time into account when calculating core busy time.
This ensures that intel_pstate will notice a decrease in load.

References: https://bugzilla.kernel.org/show_bug.cgi?id=66581
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If a PCI bridge with an ACPIPHP context attached is removed via
sysfs, the code path executed as a result is the following:

pci_stop_and_remove_bus_device_locked
 pci_remove_bus
  pcibios_remove_bus
   acpi_pci_remove_bus
    acpiphp_remove_slots
     cleanup_bridge
      unregister_hotplug_dock_device (drops dock references to the bridge)
     put_bridge
      free_bridge
       acpiphp_put_context (for each child, under context lock)
        kfree (context)

Now, if a dock event affecting one of the bridge's child devices
occurs (roughly at the same time), it will lead to the following code
path:

acpi_dock_deferred_cb
 dock_notify
  handle_eject_request
   hot_remove_dock_devices
    dock_hotplug_event
     hotplug_event (dereferences context)

That may lead to a kernel crash in hotplug_event() if it is executed
after the last kfree() in the bridge removal code path.

To prevent that from happening, add a wrapper around hotplug_event()
called dock_event() and point the .handler pointer in acpiphp_dock_ops
to it.  Make that wrapper retrieve the device's ACPIPHP context using
acpiphp_get_context() (instead of taking it from the data argument)
under acpiphp_context_lock and check if the parent bridge's
is_going_away flag is set.  If that flag is set, it will return
immediately and if it is not set it will grab a reference to the
device's parent bridge before executing hotplug_event().

Then, in the above scenario, the reference to the parent bridge
held by dock_event() will prevent free_bridge() from being executed
for it until hotplug_event() returns.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

If a PCI bridge with an ACPIPHP context attached is removed via
sysfs, the code path executed as a result is the following:

pci_stop_and_remove_bus_device_locked
 pci_remove_bus
  pcibios_remove_bus
   acpi_pci_remove_bus
    acpiphp_remove_slots
     cleanup_bridge
     put_bridge
      free_bridge
       acpiphp_put_context (for each child, under context lock)
        kfree (child context)

Now, if a hotplug notify is dispatched for one of the bridge's
children and the timing is such that handle_hotplug_event() for
that notify is executed while free_bridge() above is running,
the get_bridge(context->func.parent) in handle_hotplug_event()
will not really help, because it is too late to prevent the bridge
from going away and the child's context may be freed before
hotplug_event_work() scheduled from handle_hotplug_event()
dereferences the pointer to it passed via the data argument.
That will cause a kernel crash to happpen in hotplug_event_work().

To prevent that from happening, make handle_hotplug_event()
check the is_going_away flag of the function's parent bridge
(under acpiphp_context_lock) and bail out if it's set.  Also,
make cleanup_bridge() set the bridge's is_going_away flag under
acpiphp_context_lock so that it cannot be changed between the
check and the subsequent get_bridge(context->func.parent) in
handle_hotplug_event().

Then, in the above scenario, handle_hotplug_event() will notice
that context->func.parent->is_going_away is already set and it
will exit immediately preventing the crash from happening.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Since acpiphp_check_bridge() called by acpiphp_check_host_bridge()
does things that require PCI rescan-remove locking around it,
make acpiphp_check_host_bridge() use that locking.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Commit 9217a984 (ACPI / hotplug / PCI: Use global PCI rescan-remove
locking) modified ACPIPHP to protect its PCI device removal and addition
code paths from races against sysfs-driven rescan and remove operations
with the help of PCI rescan-remove locking.  However, it overlooked the
fact that hotplug_event_work() is not the only caller of hotplug_event()
which may also be called by dock_hotplug_event() and that code path
is missing the PCI rescan-remove locking.  This means that, although
the PCI rescan-remove lock is held as appropriate during the handling
of events originating from handle_hotplug_event(), the ACPIPHP's
operations resulting from dock events may still suffer the race
conditions that commit 9217a984 was supposed to eliminate.

To address that problem, move the PCI rescan-remove locking from
hotplug_event_work() to hotplug_event() so that it is used regardless
of the way that function is invoked.

Revamps: 9217a984 (ACPI / hotplug / PCI: Use global PCI rescan-remove locking)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>

According to the changelog of commit 29ed1f29 (PCI: pciehp: Fix null
pointer deref when hot-removing SR-IOV device) it is unsafe to walk the
bus->devices list of a PCI bus and remove devices from it in direct order,
because that may lead to NULL pointer dereferences related to virtual
functions.

For this reason, change all of the bus->devices list walks in
acpiphp_glue.c during which devices may be removed to be carried out in
reverse order.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Pull parisc updates from Helge Deller:
 "The three major changes in this patchset is a implementation for
  flexible userspace memory maps, cache-flushing fixes (again), and a
  long-discussed ABI change to make EWOULDBLOCK the same value as
  EAGAIN.

  parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
  to keep HP-UX compatibility.  Since we will probably never implement
  full HP-UX support, we prefer to drop this compatibility to make it
  easier for us with Linux userspace programs which mostly never checked
  for both values.  We don't expect major fall-outs because of this
  change, and if we face some, we will simply rebuild the necessary
  applications in the debian archives"

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts

HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps.  We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.

Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.

In the current implementation of the buffer cache, buffers are allocated
in the pagecache.  That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space.  So, we don't
need to allocate extra memory and copy the content of the buffers there.

This patch optimizes the code to avoid copying the buffers.  It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs.  This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.

New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.

This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).
Signed-off-by: Helge Deller <deller@gmx.de>

On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>

The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).
Signed-off-by: Helge Deller <deller@gmx.de>

Signed-off-by: Helge Deller <deller@gmx.de>

This commit:
f8dae006: parisc: Ensure full cache coherency for kmap/kunmap
caused negative caching side-effects, e.g. hanging processes with expect and
too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems.

This patch now partly reverts it and has been in production use on our debian buildd
makeservers since a week without any major problems.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Helge Deller <deller@gmx.de>

The built-in ROM fonts lack many necessary ASCII characters, which is
why it makes sens to prefer the Linux fonts instead if they are
available.  This makes consoles on STI graphics cards which are not
supported by the stifb driver (e.g. Visualize FXe) looks much nicer.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v3.13

Pull hwmon kconfig fixes from Jean Delvare.

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors
  hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors

Pull SLAB changes from Pekka Enberg:
 "Random bug fixes that have accumulated in my inbox over the past few
  months"

* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
  mm: Fix warning on make htmldocs caused by slab.c
  mm: slub: work around unneeded lockdep warning
  mm: sl[uo]b: fix misleading comments
  slub: Fix possible format string bug.
  slub: use lockdep_assert_held
  slub: Fix calculation of cpu slabs
  slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings

Pull turbostat updates from Len Brown.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: introduce -s to dump counters
  tools/power turbostat: remove unused command line option
  turbostat: Add option to report joules consumed per sample
  turbostat: run on HSX
  turbostat: Add a .gitignore to ignore the compiled turbostat binary
  turbostat: Clean up error handling; disambiguate error messages; use err and errx
  turbostat: Factor out common function to open file and exit on failure
  turbostat: Add a helper to parse a single int out of a file
  turbostat: Check return value of fscanf
  turbostat: Use GCC's CPUID functions to support PIC
  turbostat: Don't attempt to printf an off_t with %zx
  turbostat: Don't put unprocessed uapi headers in the include path

Pull ARM SoC fixes from Olof Johansson:
 "Here's a set of patches for (hopefully) -rc1.  Some of them are fixes,
  but a good number of them also do things such as enable new drivers in
  the defconfigs for platforms that have such devices, increases
  coverage of the multiplatform defconfig and some DTS changes that
  plumbs up some of the devices that now have bindings and driver
  support.

  The commit dates are recent; we've mostly collected these fixes in the
  last few days but I also had to rebuild the branch yesterday to sort
  out some internal conflicts which reset the timestamps.  The changes
  should have been tested by each platform maintainer already (and few
  of them have cross-platform impact) so I'm personally not too
  concerned by it at this time"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA
  ARM: multi_v7_defconfig: add mvebu drivers
  clocksource: kona: Add basic use of external clock
  drivers: bus: fix CCI driver kcalloc call parameters swap
  ARM: dts: bcm28155-ap: Fix Card Detection GPIO
  ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY
  ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set
  MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers
  ARM: dts: zynq: Add SDHCI nodes
  ARM: hisi: don't select SMP
  ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS
  ARM: multi_v7: copy most options from tegra_defconfig
  ARM: iop32x: fix power off handling for the EM7210 board
  ARM: integrator: restore static map on the CP
  ARM: msm_defconfig: Enable MSM clock drivers
  ARM: dts: msm: Add clock controller nodes and hook into uart
  ARM: OMAP4+: move errata initialization to omap4_pm_init_early
  ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle
  ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP)
  ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference
  ...

Similar to what was done for the lm75 driver.

Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>

Based on an earlier attempt by Randy Dunlap.

Fix SENSORS_LM75 dependencies to eliminate build errors:

drivers/built-in.o: In function `lm75_remove':
lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister'
drivers/built-in.o: In function `lm75_probe':
lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register'

Add depends on THERMAL since that is what provides the
register/unregister functions above, but only if THERMAL_OF was
selected as this is an optional feature of the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>

The new option allows just run turbostat and get dump of counter values. It's
useful when we have something more than one program to test.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

The -s is not used, let's remove it, and update quick help accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Pull misc kbuild changes from Michal Marek:
 "The non-critical part of kbuild is small this time:
   - Three fixes for make deb-pkg
   - A new coccinelle check

  One of the deb-pkg fixes is a leftover from the last merge window,
  hence the merge commit"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  deb-pkg: Fix building for MIPS big-endian or ARM OABI
  deb-pkg: Fix cross-building linux-headers package
  scripts: Coccinelle script for pm_runtime_* return checks with IS_ERR_VALUE
  deb-pkg: Inhibit initramfs builders if CONFIG_BLK_DEV_INITRD is not set

Both proc files are writeable and used for configuring cells. But
there is missing correct mode flag for writeable files. Without
this patch both proc files are read only.

[ It turns out they aren't really read-only, since root can write to
  them even if the write bit isn't set due to CAP_DAC_OVERRIDE ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With commit d8d14bd0 ("fs/compat: fix lookup_dcookie() parameter
handling") I changed the type of the len parameter of the
lookup_dcookie() syscall.

However I missed that there was still a stale declaration in
arch/tile/..  which now causes a compile error on tile:

  In file included from fs/dcookies.c:28:0:
  include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie'
  fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie'

Simply remove the declaration in the tile architecture, which is only a
leftover from before the different compat lookup_dcookie() versions have
been merged.  The correct declaration is now in include/linux/compat.h

The build error was reported by Fenguang's build bot.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "A set of cifs fixes (mostly for symlinks, and SMB2 xattrs) and
  cleanups"

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Fix check for regular file in couldbe_mf_symlink()
  [CIFS] Fix SMB2 mounts so they don't try to set or get xattrs via cifs
  CIFS: Cleanup cifs open codepath
  CIFS: Remove extra indentation in cifs_sfu_type
  CIFS: Cleanup cifs_mknod
  CIFS: Cleanup CIFSSMBOpen
  cifs: Add support for follow_link on dfs shares under posix extensions
  cifs: move unix extension call to cifs_query_symlink()
  cifs: Re-order M-F Symlink code
  cifs: Add create MFSymlinks to protocol ops struct
  cifs: use protocol specific call for query_mf_symlink()
  cifs: Rename MF symlink function names
  cifs: Rename and cleanup open_query_close_cifs_symlink()
  cifs: Fix memory leak in cifs_hardlink()

Pull vfs fixes from Al Viro:
 "Several obvious fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Fix mountpoint reference leakage in linkat
  hfsplus: use xattr handlers for removexattr
  Typo in compat_sys_lseek() declaration
  fs/super.c: sync ro remount after blocking writers
  vfs: unexport the getname() symbol

Pull rtl8812ae staging wireless driver from Greg KH:
 "Here's a single staging driver for a wireless chipset that has shown
  up in the SteamBox hardware.  It is merged separately from the "main"
  staging pull request to sync up with the wireless api changes that
  came in from the networking tree.

  It's self-contained and works for me and others.  Larry will be
  replacing it with a "real" driver for 3.15, but for now this one is
  needed"

* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: r8821ae: Enable build by reverting BROKEN marking
  staging: r8821ae: Fix build problems
  Staging: rtl8812ae: disable due to build errors
  Staging: rtl8821ae: add TODO file
  Staging: rtl8821ae: removed unused functions and variables
  Staging: rtl8821ae: rc.c: fix up function prototypes
  Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver

Revert commit ef83b078 "PCI: Remove from bus_list and release
resources in pci_release_dev()" that made some nasty race conditions
become possible.  For example, if a Thunderbolt link is unplugged
and then replugged immediately, the pci_release_dev() resulting from
the hot-remove code path may be racing with the hot-add code path
which after that commit causes various kinds of breakage to happen
(up to and including a hard crash of the whole system).

Moreover, the problem that commit ef83b078 attempted to address
cannot happen any more after commit 8a4c5c32 "PCI: Check parent
kobject in pci_destroy_dev()", because pci_destroy_dev() will now
return immediately if it has already been executed for the given
device.

Note, however, that the invocation of msi_remove_pci_irq_vectors()
removed by commit ef83b078 from pci_free_resources() along with
the other changes made by it is not added back because of subsequent
code changes depending on that modification.

Fixes: ef83b078 (PCI: Remove from bus_list and release resources in pci_release_dev())
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.

The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: Olof Johansson <olof@lixom.net>

Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels.  Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>

When an clock is specified in the device tree, enable it and use it to
determine the external clock frequency.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights:

   - Fix several races in nfs_revalidate_mapping
   - NFSv4.1 slot leakage in the pNFS files driver
   - Stable fix for a slot leak in nfs40_sequence_done
   - Don't reject NFSv4 servers that support ACLs with only ALLOW aces"

* tag 'nfs-for-3.14-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  nfs: initialize the ACL support bits to zero.
  NFSv4.1: Cleanup
  NFSv4.1: Clean up nfs41_sequence_done
  NFSv4: Fix a slot leak in nfs40_sequence_done
  NFSv4.1 free slot before resending I/O to MDS
  nfs: add memory barriers around NFS_INO_INVALID_DATA and NFS_INO_INVALIDATING
  NFS: Fix races in nfs_revalidate_mapping
  sunrpc: turn warn_gssd() log message into a dprintk()
  NFS: fix the handling of NFS_INO_INVALID_DATA flag in nfs_revalidate_mapping
  nfs: handle servers that support only ALLOW ACE type.

Pull sound fixes from Takashi Iwai:
 "The big chunks here are the updates for oxygen driver for Xonar DG
  devices, which were slipped from the previous pull request.  They are
  device-specific and thus not too dangerous.

  Other than that, all patches are small bug fixes, mainly for Samsung
  build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
  (And this time ASoC merge is less than Octopus, lucky seven :)"

* tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (42 commits)
  ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled
  ALSA: hda - add headset mic detect quirks for another Dell laptop
  ALSA: oxygen: Xonar DG(X): cleanup and minor changes
  ALSA: oxygen: Xonar DG(X): modify high-pass filter control
  ALSA: oxygen: Xonar DG(X): modify input select functions
  ALSA: oxygen: Xonar DG(X): modify capture volume functions
  ALSA: oxygen: Xonar DG(X): use headphone volume control
  ALSA: oxygen: Xonar DG(X): modify playback output select
  ALSA: oxygen: Xonar DG(X): capture from I2S channel 1, not 2
  ALSA: oxygen: Xonar DG(X): move the mixer code into another file
  ALSA: oxygen: modify CS4245 register dumping function
  ALSA: oxygen: modify adjust_dg_dac_routing function
  ALSA: oxygen: Xonar DG(X): modify DAC/ADC parameters function
  ALSA: oxygen: Xonar DG(X): modify initialization functions
  ALSA: oxygen: Xonar DG(X): add new CS4245 SPI functions
  ALSA: oxygen: additional definitions for the Xonar DG/DGX card
  ALSA: oxygen: change description of the xonar_dg.c file
  ALSA: oxygen: export oxygen_update_dac_routing symbol
  ALSA: oxygen: add mute mask for the OXYGEN_PLAY_ROUTING register
  ALSA: oxygen: modify the SPI writing function
  ...

Pull SCSI target updates from Nicholas Bellinger:
 "The highlights this round include:

  - add support for SCSI Referrals (Hannes)
  - add support for T10 DIF into target core (nab + mkp)
  - add support for T10 DIF emulation in FILEIO + RAMDISK backends (Sagi + nab)
  - add support for T10 DIF -> bio_integrity passthrough in IBLOCK backend (nab)
  - prep changes to iser-target for >= v3.15 T10 DIF support (Sagi)
  - add support for qla2xxx N_Port ID Virtualization - NPIV (Saurav + Quinn)
  - allow percpu_ida_alloc() to receive task state bitmask (Kent)
  - fix >= v3.12 iscsi-target session reset hung task regression (nab)
  - fix >= v3.13 percpu_ref se_lun->lun_ref_active race (nab)
  - fix a long-standing network portal creation race (Andy)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (51 commits)
  target: Fix percpu_ref_put race in transport_lun_remove_cmd
  target/iscsi: Fix network portal creation race
  target: Report bad sector in sense data for DIF errors
  iscsi-target: Convert gfp_t parameter to task state bitmask
  iscsi-target: Fix connection reset hang with percpu_ida_alloc
  percpu_ida: Make percpu_ida_alloc + callers accept task state bitmask
  iscsi-target: Pre-allocate more tags to avoid ack starvation
  qla2xxx: Configure NPIV fc_vport via tcm_qla2xxx_npiv_make_lport
  qla2xxx: Enhancements to enable NPIV support for QLOGIC ISPs with TCM/LIO.
  qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
  IB/isert: pass scatterlist instead of cmd to fast_reg_mr routine
  IB/isert: Move fastreg descriptor creation to a function
  IB/isert: Avoid frwr notation, user fastreg
  IB/isert: seperate connection protection domains and dma MRs
  tcm_loop: Enable DIF/DIX modes in SCSI host LLD
  target/rd: Add DIF protection into rd_execute_rw
  target/rd: Add support for protection SGL setup + release
  target/rd: Refactor rd_build_device_space + rd_release_device_space
  target/file: Add DIF protection support to fd_execute_rw
  target/file: Add DIF protection init/format support
  ...