Some further updates for net-next:
 * fix network-manager which was broken by the previous changes
 * fix delete-station events, which were broken by me making the
   genlmsg_end() mistake
 * fix a timer left running during suspend in some race conditions
   that would cause an annoying (but harmless) warning
 * (less important, but in the tree already) remove 80+80 MHz rate
   reporting since the spec doesn't distinguish it from 160 MHz;
   as the bitrate they're both 160 MHz bandwidth

If the firmware sends spontaneous DTS notfications with the
temperature (indicated in a TLV), we can ignore the temperature we get
in the RX statistics notifications.  This prevents potentially
handling the same temperature change twice.  It also ignores
notifications with temperature equal to 0 that happens from time to
time.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

These aren't useful and overflowing so drop them
and also fix a minor typo.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to duplicate the structure field name in the string,
just generate the string in the macro that's there anyway. To keep
the debugfs output the same, rename one (otherwise unused) field.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware API structs are split differently, synchronize
the struct splits with the current firmware definitions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When we want to trigger an NMI in the device, we need to set
bit 7 and not bit 0. However, older firmwares don't register
to the interrupt issued by bit 7. Use bit 7 first so that
the correct interrupt will be issued hoping that the firmware
will react. To be on the safe side, set bit 0 in case the
firmware didn't register to the proper interrupt.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the FW is in error status - try to read the RXF and
TXF (all of them) and add them to the dump data.

This shouldn't happen in non-error statuses, as we don't
want to stop the RXF/TXF while they are running.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some HW modules have two SRAMs. In such cases add the secondary SRAM to
the list of dumped segments.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

As this functionality relies on getting a firmware notification
it is difficult to test. Allow accessing the data for it from
debugfs to be able to trigger all kinds of scenarios to test.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A new host command can be used to configure the scheduler
instead of accessing the scheduler's registers from the
driver. This is easier and less error prone since accessing
the hardware at certain moments can lead to races with the
firmware.
Prefer to use the host command whenever it is available.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Use only basic dwell time (10 ms for active scan and 110 for passive),
regardless of the number of the probes and the band, if it is
supported by the FW. The FW will add 3 ms for each probe sent and 10
ms for low band channels.
Add a TLV flag to indicate such support in FW.

This fix is needed to fix few bugs regarding scans that take too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver doesn't support the firmwares that don't have
these capabilities. The code that actually used these
flags has been removed already, but the flags were left
for an unclear reason. Remove them.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Print the nvm version in the log for debugging purposes.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Fragmented scan should be applied for all channels, passive and active.
When scanning on passive channels the firmware uses frag_passive_dwell
to define the maximum continuous scan time before returning to the
operating channel. On active channels max_out_time is the parameter
used by the firmware to define the maximum time allowed out of the
operating channel. Since active channels' scan should also be fragmented
set max_out_time equal to frag_passive_dwell.
In addition:
- Set max_out_time and suspend_time if the firmware doesn't support
  fragmented scan to avoid unexpected behavior.
- Adjust max_out_time for second level of scan precedence.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is to work around interoperability bugs with devices
that don't hanle MIMO properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

iwl_mvm_fw_dbg_collect allows to collect debug data from
the firmware. Most of the firmware interaction is done in
non-sleepable context. It makes little sense to force the
caller of iwl_mvm_fw_dbg_collect to sleep.
Defer the actual collection to a worker so that this
function will be able to be called from any context.
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case platform is in d0i3 - make sure it is awake when
writing the registers to stop the monitor when collecting FW
debug data. Plus, remove unneeded mutex locking currently
done.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This option enables scan offload iteration complete notification from
firmware which includes the last iteration's status and the scanned
channels from the current iteration.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new config for 4165 series over PCI and insert support
for two new 4165 series PCI IDs.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes sure that we're not trying to read/write any of
the FW debug data collected during d0i3.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Repeating the legacy rates avoids degrading quickly to
lower rates due to collisions which is common when doing
TCP Tx traffic in legacy.
This slightly improves TCP Tx throughput while working
in legacy in different scenarios.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If Tx failed because the STA was in powersave there's no point
in sending a BAR so avoid indicating AMPDU_NO_BACK to mac80211.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

While suspending, we destroy the authentication /
association that might be taking place. While doing so, we
forgot to delete the timer which can be firing after
local->suspended is already set, producing the warning below.

Fix that by deleting the timer.

[66722.825487] WARNING: CPU: 2 PID: 5612 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]()
[66722.825487] queueing ieee80211 work while going to suspend
[66722.825529] CPU: 2 PID: 5612 Comm: kworker/u16:69 Tainted: G        W  O  3.16.1+ #24
[66722.825537] Workqueue: events_unbound async_run_entry_fn
[66722.825545] Call Trace:
[66722.825552]  <IRQ>  [<ffffffff817edbb2>] dump_stack+0x4d/0x66
[66722.825556]  [<ffffffff81075cad>] warn_slowpath_common+0x7d/0xa0
[66722.825572]  [<ffffffffa06b5b90>] ? ieee80211_sta_bcn_mon_timer+0x50/0x50 [mac80211]
[66722.825573]  [<ffffffff81075d1c>] warn_slowpath_fmt+0x4c/0x50
[66722.825586]  [<ffffffffa06977a2>] ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]
[66722.825598]  [<ffffffffa06977d5>] ieee80211_queue_work+0x25/0x50 [mac80211]
[66722.825611]  [<ffffffffa06b5bac>] ieee80211_sta_timer+0x1c/0x20 [mac80211]
[66722.825614]  [<ffffffff8108655a>] call_timer_fn+0x8a/0x300
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This reverts commit ba1debdf.

Oliver reported that it breaks network-manager, for some reason with
this patch NM decides that the device isn't wireless but "generic"
(ethernet), sees no carrier (as expected with wifi) and fails to do
anything else with it.

Revert this to unbreak userspace.
Reported-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The return value from nl80211_send_station() is the length of the
skb, or a negative error, so abort sending the message only when
the return value was negative.

This fixes the ibss_rsn wpa_supplicant test case.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For some reason, we made the bandwidth separate flags, which
is rather confusing - a single rate cannot have different
bandwidths at the same time.

Change this to no longer be flags but use a separate field
for the bandwidth ('bw') instead.

While at it, add support for 5 and 10 MHz rates - these are
reported as regular legacy rates with their real bitrate,
but tagged as 5/10 now to make it easier to distinguish them.

In the nl80211 API, the flags are preserved, but the code
now can also clearly only set a single one of the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

These rates are treated the same as 160 MHz in the spec, so
it makes no sense to distinguish them. As no driver uses them
yet, this is also not a problem, just remove them.

In the userspace API the field remains reserved to preserve
API and ABI.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

These rates are treated the same as 160 MHz in the spec,
so it makes no sense to distinguish them. As no driver
uses them yet, this is also not a problem, just remove
them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

I removed the enum earlier, but forgot to remove it from the
documentation - do that now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Send the netdetect configuration information in the response to
NL8021_CMD_GET_WOWLAN commands.  This includes the scan interval,
SSIDs to match and frequencies to scan.

Additionally, add the NL80211_WOWLAN_TRIG_NET_DETECT with
NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a system contains only self-managed regulatory devices all hints
from the regulatory core are ignored. Stop hint processing early in this
case. These systems usually don't have CRDA deployed, which results in
endless (irrelevent) logs of the form:
cfg80211: Calling CRDA to update world regulatory domain

Make sure there's at least one self-managed device before discarding a
hint, in order to prevent initial hints from disappearing on CRDA
managed systems.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

A self-managed device will sometimes need to set its regdomain synchronously.
Notably it should be set before usermode has a chance to query it. Expose
a new API to accomplish this which requires the RTNL.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Radar detection can last indefinite time. There is no
point in deferring a scan request in this case - simply
return -EBUSY.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ctx->conf.radar_enabled should reflect whether radar
detection is enabled for the channel context.

When calculating it, make it consider only the vifs
that have this context assigned (instead of all the
vifs).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

local->radar_detect_enabled should tell whether
radar_detect is enabled on any interface belonging
to local.

However, it's not getting updated correctly
in many cases (actually, when testing with hwsim
it's never been set, even when the dfs master
is beaconing).

Instead of handling all the corner cases
(e.g. channel switch), simply check whether
radar detection is enabled only when needed,
instead of caching the result.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The function adding the supported channels IE during a TDLS connection had
several issues:
1. If the entire subband is usable, the function exitted the loop without
   adding it
2. The function only checked chandef_usable, ignoring flags like RADAR
   which would prevent TDLS off-channel communcation.
3. HT20 was explicitly required in the chandef, while not a requirement
   for TDLS off-channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.

For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Document the rfkill module parameters default_state and
master_switch_mode.
Signed-off-by: Andrew Clausen <andrew.p.clausen@gmail.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>