To identify timestamps for matching with their packets, Spectrum-1 uses a
five-tuple of (port, direction, domain number, message type, sequence ID).
If there are several clients from the same domain behind a single port
sending Delay_Req's, the only thing differentiating these packets, as far
as Spectrum-1 is concerned, is the sequence ID. Should sequence IDs between
individual clients be similar, conflicts may arise. That is not a problem
to hardware, which will simply deliver timestamps on a first comes, first
served basis.

However the driver uses a simple hash table to store the unmatched pieces.
When a new conflicting piece arrives, it pushes out the previously stored
one, which if it is a packet, is delivered without timestamp. Later on as
the corresponding timestamps arrive, the first one is mismatched to the
second packet, and the second one is never matched and eventually is GCd.

To correct this issue, instead of using a simple rhashtable, use rhltable
to keep the unmatched entries.

Previously, a found unmatched entry would always be removed from the hash
table. That is not the case anymore--an incompatible entry is left in the
hash table. Therefore removal from the hash table cannot be used to confirm
the validity of the looked-up pointer, instead the lookup would simply need
to be redone. Therefore move it inside the critical section. This
simplifies a lot of the code.

Fixes: 87486427 ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Reported-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adjust the function names in two doc comments to match the corresponding
functions.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix rxrpc_unuse_local() to handle a NULL local pointer as it can be called
on an unbound socket on which rx->local is not yet set.

The following reproduced (includes omitted):

	int main(void)
	{
		socket(AF_RXRPC, SOCK_DGRAM, AF_INET);
		return 0;
	}

causes the following oops to occur:

	BUG: kernel NULL pointer dereference, address: 0000000000000010
	...
	RIP: 0010:rxrpc_unuse_local+0x8/0x1b
	...
	Call Trace:
	 rxrpc_release+0x2b5/0x338
	 __sock_release+0x37/0xa1
	 sock_close+0x14/0x17
	 __fput+0x115/0x1e9
	 task_work_run+0x72/0x98
	 do_exit+0x51b/0xa7a
	 ? __context_tracking_exit+0x4e/0x10e
	 do_group_exit+0xab/0xab
	 __x64_sys_exit_group+0x14/0x17
	 do_syscall_64+0x89/0x1d4
	 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Reported-by: syzbot+20dee719a2e090427b5f@syzkaller.appspotmail.com
Fixes: 730c5fd4 ("rxrpc: Fix local endpoint refcounting")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to the commit in the fixes tag, the resource controller in netdevsim
tracked fib entries and rules per network namespace. Restore that behavior.

Fixes: 5fc49422 ("netdevsim: create devlink instance per netdevsim instance")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2019-08-11

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) x64 JIT code generation fix for backward-jumps to 1st insn, from Alexei.

2) Fix buggy multi-closing of BTF file descriptor in libbpf, from Andrii.

3) Fix libbpf_num_possible_cpus() to make it thread safe, from Takshak.

4) Fix bpftool to dump an error if pinning fails, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we swap the original proto and clear the ULP pointer
on close we have to make sure no callback will try to access
the freed state. sk_write_space is not part of sk_prot, remember
to swap it.

Reported-by: syzbot+dcdc9deefaec44785f32@syzkaller.appspotmail.com
Fixes: 95fa1454 ("bpf: sockmap/tls, close can race with map free")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a warning of "suspicious rcu_dereference_check() usage"
when nload runs.

Fixes: 776e726b ("netvsc: fix RCU warning in get_stats")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-08-08

This series introduces some fixes to mlx5 driver.

Highlights:
1) From Tariq, Critical mlx5 kTLS fixes to better align with hw specs.
2) From Aya, Fixes to mlx5 tx devlink health reporter.
3) From Maxim, aRFs parsing to use flow dissector to avoid relying on
invalid skb fields.

Please pull and let me know if there is any problem.

For -stable v4.3
 ('net/mlx5e: Only support tx/rx pause setting for port owner')
For -stable v4.9
 ('net/mlx5e: Use flow keys dissector to parse packets for ARFS')
For -stable v5.1
 ('net/mlx5e: Fix false negative indication on tx reporter CQE recovery')
 ('net/mlx5e: Remove redundant check in CQE recovery flow of tx reporter')
 ('net/mlx5e: ethtool, Avoid setting speed to 56GBASE when autoneg off')

Note: when merged with net-next this minor conflict will pop up:
++<<<<<<< (net-next)
 +      if (is_eswitch_flow) {
 +              flow->esw_attr->match_level = match_level;
 +              flow->esw_attr->tunnel_match_level = tunnel_match_level;
++=======
+       if (flow->flags & MLX5E_TC_FLOW_ESWITCH) {
+               flow->esw_attr->inner_match_level = inner_match_level;
+               flow->esw_attr->outer_match_level = outer_match_level;
++>>>>>>> (net)

To resolve, use hunks from net (2nd) and replace:
if (flow->flags & MLX5E_TC_FLOW_ESWITCH)
with
if (is_eswitch_flow)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe_service_task() calls unregister_netdev() under rtnl_lock().
But unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.

Fixes: 59dd45d5 ("ixgbe: firmware recovery mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Fix collisions in socket cookie generation

This change makes the socket cookie generator as a global counter
instead of per netns in order to fix cookie collisions for BPF use
cases we ran into. See main patch #1 for more details.

Given the change is small/trivial and fixes an issue we're seeing
my preference would be net tree (though it cleanly applies to
net-next as well). Went for net tree instead of bpf tree here given
the main change is in net/core/sock_diag.c, but either way would be
fine with me.

v1 -> v2:
  - Fix up commit description in patch #1, thanks Eric!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull in updates in BPF helper function description.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Generating and retrieving socket cookies are a useful feature that is
exposed to BPF for various program types through bpf_get_socket_cookie()
helper.

The fact that the cookie counter is per netns is quite a limitation
for BPF in practice in particular for programs in host namespace that
use socket cookies as part of a map lookup key since they will be
causing socket cookie collisions e.g. when attached to BPF cgroup hooks
or cls_bpf on tc egress in host namespace handling container traffic
from veth or ipvlan devices with peer in different netns. Change the
counter to be global instead.

Socket cookie consumers must assume the value as opqaue in any case.
Not every socket must have a cookie generated and knowledge of the
counter value itself does not provide much value either way hence
conversion to global is fine.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Martynas Pumputis <m@lambda.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
Here's a couple of fixes for rxrpc:

 (1) Fix refcounting of the local endpoint.

 (2) Don't calculate or report packet skew information.  This has been
     obsolete since AFS 3.1 and so is a waste of resources.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
First make sure we don't use "prog" in error messages because
the pinning operation could be performed on a map. Second add
back missing error message if pin syscall failed.
====================
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

No error message is currently printed if the pin syscall
itself fails. It got lost in the loadall refactoring.

Fixes: 77380998 ("bpftool: add loadall command")
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Change an error message to work for any object being
pinned not just programs.

Fixes: 71bb428f ("tools: bpf: add bpftool")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Don't bother generating maxSkew in the ACK packet as it has been obsolete
since AFS 3.1.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>

The object lifetime management on the rxrpc_local struct is broken in that
the rxrpc_local_processor() function is expected to clean up and remove an
object - but it may get requeued by packets coming in on the backing UDP
socket once it starts running.

This may result in the assertion in rxrpc_local_rcu() firing because the
memory has been scheduled for RCU destruction whilst still queued:

	rxrpc: Assertion failed
	------------[ cut here ]------------
	kernel BUG at net/rxrpc/local_object.c:468!

Note that if the processor comes around before the RCU free function, it
will just do nothing because ->dead is true.

Fix this by adding a separate refcount to count active users of the
endpoint that causes the endpoint to be destroyed when it reaches 0.

The original refcount can then be used to refcount objects through the work
processor and cause the memory to be rcu freed when that reaches 0.

Fixes: 4f95dd78 ("rxrpc: Rework local endpoint management")
Reported-by: syzbot+1e0edc4b8b7494c28450@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>

As spin_unlock_irq will enable interrupts.
Function tsi108_stat_carry is called from interrupt handler tsi108_irq.
Interrupts are enabled in interrupt handler.
Use spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq
in IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should also enable team's vlan tx offload in hw_enc_features,
pass the vlan packets to the slave devices with vlan tci, let the
slave handle vlan tunneling offload implementation.

Fixes: 3268e5cb ("team: Advertise tunneling offload features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.

Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.

Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.

Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.

Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).

See commit 0608c69c ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.

v2:
 - remove superfluous decrypted mark copy (Willem);
 - remove the stale doc entry (Boris);
 - rely entirely on EOR marking to prevent coalescing (Boris);
 - use an internal sendpages flag instead of marking the socket
   (Boris).
v3 (Willem):
 - reorganize the can_skb_orphan_partial() condition;
 - fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roman Mashak says:

====================
Fix batched event generation for skbedit action

When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.

For example, consider the following script adding 32 entries with all
supported skbedit parameters and cookie (in order to maximize netlink
messages size):

% cat tc-batch.sh
TC="sudo /mnt/iproute2.git/tc/tc"

$TC actions flush action skbedit
for i in `seq 1 $1`;
do
   cmd="action skbedit queue_mapping 2 priority 10 mark 7/0xaabbccdd \
               ptype host inheritdsfield \
               index $i cookie aabbccddeeff112233445566778800a1 "
   args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%

patch 1 adds callback in tc_action_ops of skbedit action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().

patch 2 updates the TDC test suite with relevant skbedit test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update TDC tests with cases varifying ability of TC to install or delete
batches of skbedit actions.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add get_fill_size() routine used to calculate the action size
when building a batch of events.

Fixes: ca9b0e27 ("pkt_action: add new action skbedit")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/dsa/sja1105/sja1105_main.c: In function sja1105_fdb_dump:
drivers/net/dsa/sja1105/sja1105_main.c:1226:14: warning:
 variable tx_vid set but not used [-Wunused-but-set-variable]
drivers/net/dsa/sja1105/sja1105_main.c:1226:6: warning:
 variable rx_vid set but not used [-Wunused-but-set-variable]

They are not used since commit 6d7c7d94 ("net: dsa:
sja1105: Fix broken learning with vlan_filtering disabled")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As commit 30d8177e ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.

Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:

	 if (skb->encapsulation)
                 features &= dev->hw_enc_features;

clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e like this:

vlan_dev_hard_start_xmit
  -->dev_queue_xmit
    -->validate_xmit_skb
      -->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
      -->validate_xmit_vlan
        -->__vlan_hwaccel_push_inside //skb->tci is cleared
...
 --> bond_start_xmit
   --> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
     --> __skb_flow_dissect // nhoff point to IP header
        -->  case htons(ETH_P_8021Q)
             // skb_vlan_tag_present is false, so
             vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
             //vlan point to ip header wrongly

Fixes: b2a103e6 ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In error case, all entries should be freed from the sched list
before deleting it. For simplicity use rcu way.

Fixes: 5a781ccb ("tc: Add support for configuring the taprio scheduler")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPX is no longer supported, but the example in the documentation
might useful. Replace it with IPv6.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both IPX and TR have not been supported for a while now.
Remove them from the /proc/sys/net documentation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before commit d4289fcc ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).

By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e3 ("Revert
"ipv4: use skb coalescing in defragmentation"")).

Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.

When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.

Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.

This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.

[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1

Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove check of recovery bit, in the beginning of the CQE recovery
function. This test is already performed right before the reporter
is invoked, when CQE error is detected.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

CQE recovery function begins with test and set of recovery bit. Add an
error flow which ensures clearing of this bit when leaving the recovery
function, to allow further recoveries to take place. This allows removal
of clearing recovery bit on sq activate.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Remove wrong error return value when SQ is not in error state.
CQE recovery on TX reporter queries the sq state. If the sq is not in
error state, the sq is either in ready or reset state. Ready state is
good state which doesn't require recovery and reset state is a temporal
state which ends in ready state. With this patch, CQE recovery in this
scenario is successful.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Shift the tisn field in the WQE control segment, per the
HW specification.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use the proper tisn field name from the union in struct mlx5_wqe_ctrl_seg.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The TLS progress params context WQE should not include an
Eth segment, drop it.
In addition, align the tls_progress_params layout with the
HW specification document:
- fix the tisn field name.
- remove the valid bit.

Fixes: a12ff35e ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the used constants for TLS TIS opmods, per the HW specification.

Fixes: a12ff35e ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the 128b key offset in key encryption key creation command,
per the HW specification.

Fixes: 45d3b55d ("net/mlx5: Add crypto library to support create/destroy encryption key")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Setting speed to 56GBASE is allowed only with auto-negotiation enabled.

This patch prevent setting speed to 56GBASE when auto-negotiation disabled.

Fixes: f62b8bb8 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Mohamad Heib <mohamadh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>