Caught by the text editor. Fix it separately from the actual changes.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow Dissector code never modifies the input buffer, neither skb nor
raw data.
Make 'data' argument const for all of the Flow dissector's functions.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function never modifies the input buffer, so 'data' argument
can be marked as const.
This implies one harmless cast-away.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

BPF Flow dissection programs are read-only and don't touch input
buffers.
Mark 'data' and 'data_end' in struct bpf_flow_dissector as const
in preparation for global input constifying.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Lobakin says:

====================
gro: micro-optimize dev_gro_receive()

This random series addresses some of suboptimal constructions used
in the main GRO entry point.
The main body is gro_list_prepare() simplification and pointer usage
optimization in dev_gro_receive() itself. Being mostly cosmetic, it
gives like +10 Mbps on my setup to both TCP and UDP (both single- and
multi-flow).

Since v1 [0]:
 - drop the replacement of bucket index calculation with
   reciprocal_scale() since it makes absolutely no sense (Eric);
 - improve stack usage in dev_gro_receive() (Eric);
 - reverse the order of patches to avoid changes superseding.

[0] https://lore.kernel.org/netdev/20210312162127.239795-1-alobakin@pm.me
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

'hash' stores not the flow hash, but the index of the GRO bucket
corresponding to it.
Change its name to 'bucket' to avoid confusion while reading lines
like '__set_bit(hash, &napi->gro_bitmask)'.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRO bucket index doesn't change through the entire function.
Store a pointer to the corresponding bucket instead of its member
and use it consistently through the function.
It is performance-safe since &gro_list->list == gro_list.

Misc: remove superfluous braces around single-line branches.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro_list_prepare() always returns &napi->gro_hash[bucket].list,
without any variations. Moreover, it uses 'napi' argument only to
have access to this list, and calculates the bucket index for the
second time (firstly it happens at the beginning of
dev_gro_receive()) to do that.
Given that dev_gro_receive() already has an index to the needed
list, just pass it as the first argument to eliminate redundant
calculations, and make gro_list_prepare() return void.
Also, both arguments of gro_list_prepare() can be constified since
this function can only modify the skbs from the bucket list.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>

The BCM4908 switch has 256 CFP entrie, update that setting so CFP can be
used.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The batching logic in netvsc_send is non-trivial, due to
a combination of the Linux API and the underlying hypervisor
interface. Add a comment explaining why the code is written this
way.
Signed-off-by: Shachar Raindel <shacharr@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
pktgen: scripts improvements

Please consider small improvements to pktgen scripts we use in our environment.

Adding delay parameter through command line,
Adding new -a (append) parameter to make flex runs

v3: change us to ns in docs
v2: Review comments from Jesper

CC: Jesper Dangaard Brouer <brouer@redhat.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

To configure various complex flows we for sure can create custom
pktgen init scripts, but sometimes thats not that easy.

New "-a" (append) option in all the existing sample scripts allows
to append more "devices" into pktgen threads.

The most straightforward usecases for that are:
- using multiple devices. We have to generate full linerate on
all physical functions (ports) of our multiport device.
- pushing multiple flows (with different packet options)
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DELAY may now be explicitly specified via common parameter -w
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation is missing and it's not very clear what
this callback is for - presumably testing the recovery?
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Minor tweaks and improvement of wording about the diagnose callback.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit eaf4fac4 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver.  This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.

(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added a blank line after structure declaration.
This is done to maintain code uniformity.
Signed-off-by: Sanjana Srinidhi <sanjanasrinidhi1810@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s/calclation/calculation/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kurt Kanzenbach says:

====================
net: dsa: hellcreek: Add support for dumping tables

add support for dumping the VLAN and FDB table via devlink. As the driver uses
internal VLANs and static FDB entries, this is a useful debugging feature.

Changes since v1:

 * Drop memory reporting as there are better APIs to expose this
 * Move comment to VLAN patch

Previous versions:

 * https://lkml.kernel.org/netdev/20210311175344.3084-1-kurt@kmk-computers.de/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to dump the FDB table via devlink. This is a useful debugging feature.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two functions which need to populate fdb entries. Move that to a
helper function.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hellcreek_select_vlan() takes a boolean instead of an integer.
So, use false accordingly.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to dump the VLAN table via devlink. This especially useful, because the
driver internally leverages VLANs for the port separation. These are not visible
via the bridge utility.
Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
There is only a single patch this time:

 - Use netif_rx_any_context(), by Sebastian Andrzej Siewior
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
net/sched: act_police: add support for packet-per-second policing

This series enhances the TC policer action implementation to allow a
policer action instance to enforce a rate-limit based on
packets-per-second, configurable using a packet-per-second rate and burst
parameters.

In the hope of aiding review this is broken up into three patches.

* [PATCH 1/3] flow_offload: add support for packet-per-second policing

  Add support for this feature to the flow_offload API that is used to allow
  programming flows, including TC rules and their actions, into hardware.

* [PATCH 2/3] flow_offload: reject configuration of packet-per-second policing in offload drivers

  Teach all exiting users of the flow_offload API that allow offload of
  policer action instances to reject offload if packet-per-second rate
  limiting is configured: none support it at this time

* [PATCH 3/3] net/sched: act_police: add support for packet-per-second policing

  With the above ground-work in place add the new feature to the TC policer
  action itself

With the above in place the feature may be used.

As follow-ups we plan to provide:
* Corresponding updates to iproute2
* Corresponding self tests (which depend on the iproute2 changes)
* Hardware offload support for the NFP driver

Key changes since v2:
* Added patches 1 and 2, which makes adding patch 3 safe for existing
  hardware offload of the policer action
* Re-worked patch 3 so that a TC policer action instance may be configured
  for packet-per-second or byte-per-second rate limiting, but not both.
* Corrected kdoc usage
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow a policer action to enforce a rate-limit based on packets-per-second,
configurable using a packet-per-second rate and burst parameters.

e.g.
tc filter add dev tap1 parent ffff: u32 match \
        u32 0 0 police pkts_rate 3000 pkts_burst 1000

Testing was unable to uncover a performance impact of this change on
existing features.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A follow-up patch will allow users to configures packet-per-second policing
in the software datapath. In preparation for this, teach all drivers that
support offload of the policer action to reject such configuration as
currently none of them support it.
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow flow_offload API to configure packet-per-second policing using rate
and burst parameters.

Dummy implementations of tcf_police_rate_pkt_ps() and
tcf_police_burst_pkt() are supplied which return 0, the unconfigured state.
This is to facilitate splitting the offload, driver, and TC code portion of
this feature into separate patches with the aim of providing a logical flow
for review. And the implementation of these helpers will be filled out by a
follow-up patch.
Signed-off-by: Xingfeng Hu <xingfeng.hu@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: support imp-controlled PHYs

This series adds support for imp-controlled PHYs in the HNS3
ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the imp-controlled PHYs feature is enabled, driver can not
call phy driver interface to set loopback anymore and needs
to send command to firmware to start phy loopback.

Driver reuses the existing firmware command 0x0315 to start
phy loopback, just add a setting bit in this command. As this
command is not only for serdes loopback anymore, rename this
command to "xxx_COMMON_LOOPBACK", and modify function name,
macro name and logs related to it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the imp-controlled PHYs feature is enabled, driver will not
register mdio bus. In order to support ioctl ops for phy tool to
read or write phy register in this case, the firmware implement
a new command for driver and driver implement ioctl by using this
new command.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the imp-controlled PHYs feature is enabled, phydev is NULL.
In this case, the autoneg is always off when user uses ethtool -a
command to get pause parameters because  hclge_get_pauseparam()
uses phydev to check whether device is TP port. To fit this new
feature, use media type to check whether device is TP port.

And when user set pause parameters, these parameters need to
always set to mac, no matter whether autoneg is off.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IMP(Intelligent Management Processor) firmware add a new feature
to take control of PHYs for some new devices, PF driver adds
support for this feature.

Driver queries device's capability to check whether IMP supports
this feature, it will tell IMP to enable this feature by firmware
compatible command if it is supported.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sergey Shtylyov says:

====================
sh_eth: Improve the register/bit definitions in the Ether driver

Here are 4 patches against DaveM's 'net-next' repo. Mainly I'm renaming the register *enum*
tags/entries to match the SoC manuals,and also moving the RX-TX descriptor *enum*s closer to
the corresponding *struct*s...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Place the RX/TX descriptor bit *enum*s where they belong -- after the
corresponding RX/TX descriptor *struct*s and, while at it, switch to
declaring one *enum* entry per line...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Finally, rename the rest of the *enum* tags still not (exactly) matching
the abbreviated register names from the manuals...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

In all the SoC manuals (except R-Car gen2) the PHY status register's name
is abbreviated to  PSR with the only valid bit 0 named LMON.  Follow the
suit and rename the corresponding *enum* tag/entry.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

In all the SoC manuals the TRSCER register bits match the corresponding
EESR registers's bits, but only on the R-Car gen2 SoC those are named
RINT<n> and TINT<n>.  Follow the suit and rename the *enum* tag/entries
from DESC_I_* to TRSCER_*.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Include multiple address ids in RM_ADDR

Here's a patch series from the MPTCP tree that extends the capabilities
of the MPTCP RM_ADDR header.

MPTCP peers can exchange information about their IP addresses that are
available for additional MPTCP subflows. IP addresses are advertised
with an ADD_ADDR header type, and those advertisements are revoked with
the RM_ADDR header type. RFC 8684 allows the RM_ADDR header to include
more than one address ID, so multiple advertisements can be revoked in a
single header. Previous kernel versions have only used RM_ADDR with a
single address ID, so multiple removals required multiple packets.

Patches 1-4 plumb address id list structures around the MPTCP code,
where before only a single address ID was passed.

Patches 5-8 make use of the address lists at the path manager layer that
tracks available addresses for both peers.

Patches 9-11 update the selftests to cover the new use of RM_ADDR with
multiple address IDs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added the testcases for removing a list of addresses. Used
the netlink to flush the addresses in the testcases.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>