- 21 Jan, 2021 18 commits
-
-
Felix Fietkau authored
This allows drivers to pass 802.3 frames to mac80211, with some restrictions: - the skb must be passed with a valid sta - fast-rx needs to be active for the sta - monitor mode needs to be disabled mac80211 will tell the driver when it is safe to enable rx decap offload for a particular station. In order to implement support, a driver must: - call ieee80211_hw_set(hw, SUPPORTS_RX_DECAP_OFFLOAD) - implement ops->sta_set_decap_offload - mark 802.3 frames with RX_FLAG_8023 If it doesn't want to enable offload for some vif types, it can mask out IEEE80211_OFFLOAD_DECAP_ENABLED in vif->offload_flags from within the .add_interface or .update_vif_offload driver ops Signed-off-by:
Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20201218184718.93650-6-nbd@nbd.nameSigned-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Felix Fietkau authored
A sorted flow list is only needed to drop packets in the biggest flow when hitting the overmemory condition. By scanning flows only when needed, we can avoid paying the cost of maintaining the list under normal conditions In order to avoid scanning lots of empty flows and touching too many cold cache lines, a bitmap of flows with backlog is maintained Signed-off-by:
-
Felix Fietkau authored
Simplifies the code and prepares for a rework of scanning for flows on overmemory drop. Signed-off-by:
-
Felix Fietkau authored
This is similar to what sch_fq_codel does. It also amortizes the worst case cost of a follow-up patch that changes the selection of the biggest flow for dropping packets Signed-off-by:
-
Martin Blumenstingl authored
When has_prg_eth1_rgmii_rx_delay is true then we support RX delays between 0ps and 3000ps in 200ps steps. Swap the validation of the RX delay based on the has_prg_eth1_rgmii_rx_delay flag so the 200ps check is now applied correctly on G12A SoCs (instead of only allow 0ps or 2000ps on G12A, but 0..3000ps in 200ps steps on older SoCs which don't support that). Fixes: de94fc10 ("net: stmmac: dwmac-meson8b: add support for the RGMII RX delay on G12A") Reported-by:
Martijn van Deventer <martijn@martijnvandeventer.nl> Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20210119202424.591349-1-martin.blumenstingl@googlemail.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Xin Long authored
This patch is to let it always do CRC checksum in sctp_gso_segment() by removing CRC flag from the dev features in gre_gso_segment() for SCTP over GRE, just as it does in Commit 527beb8e ("udp: support sctp over udp in skb_udp_tunnel_segment") for SCTP over UDP. It could set csum/csum_start in GSO CB properly in sctp_gso_segment() after that commit, so it would do checksum with gso_make_checksum() in gre_gso_segment(), and Commit 622e32b7 ("net: gre: recompute gre csum for sctp over gre tunnels") can be reverted now. Note that when need_csum is false, we can still leave CRC checksum of SCTP to HW by not clearing this CRC flag if it's supported, as Jakub and Alex noticed. v1->v2: - improve the changelog. - fix "rev xmas tree" in varibles declaration. v2->v3: - remove CRC flag from dev features only when need_csum is true. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Link: https://lore.kernel.org/r/00439f24d5f69e2c6fa2beadc681d056c15c258f.1610772251.git.lucien.xin@gmail.comSigned-off-by:
-
Xin Long authored
In __skb_udp_tunnel_segment(), when it's a SCTP over VxLAN/GENEVE packet and need_csum is false, which means the outer udp checksum doesn't need to be computed, csum_start and csum_offset could be used by the inner SCTP CRC CSUM for SCTP HW CRC offload. So this patch is to not remove the CRC flag from dev features when need_csum is false. Signed-off-by:
-
wenxu authored
This patch add the TCA_FLOWER_KEY_CT_FLAGS_INVALID flag to match the ct_state with invalid for conntrack. Signed-off-by:
wenxu <wenxu@ucloud.cn> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Link: https://lore.kernel.org/r/1611045110-682-1-git-send-email-wenxu@ucloud.cnSigned-off-by:
-
Jakub Kicinski authored
After recent changes to the error path of register_netdevice() we no longer need a version of unregister_netdevice_many() which does not set net_todo. We can inline the rollback_registered() functions into respective unregister_netdevice() calls. Link: https://lore.kernel.org/r/20210119202521.3108236-1-kuba@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Similar to the change for rollback_registered() - rollback_registered_many() was a part of unregister_netdevice_many() minus the net_set_todo(), which is no longer needed. Functionally this patch moves the list_empty() check back after: BUG_ON(dev_boot_phase); ASSERT_RTNL(); but I can't find any reason why that would be an issue. Reviewed-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
-
Jakub Kicinski authored
Move rollback_registered_many() and add a temporary forward declaration to make merging the code into unregister_netdevice_many() easier to review. No functional changes. Reviewed-by:
-
Jakub Kicinski authored
rollback_registered() is a local helper, it's common for driver code to call unregister_netdevice_queue(dev, NULL) when they want to unregister netdevices under rtnl_lock. Inline rollback_registered() and adjust the only remaining caller. Reviewed-by:
-
Jakub Kicinski authored
Commit 93ee31f1 ("[NET]: Fix free_netdev on register_netdev failure.") moved net_set_todo() outside of rollback_registered() so that rollback_registered() can be used in the failure path of register_netdevice() but without risking a double free. Since commit cf124db5 ("net: Fix inconsistent teardown and release of private netdev state."), however, we have a better way of handling that condition, since destructors don't call free_netdev() directly. After the change in commit c269a24c ("net: make free_netdev() more lenient with unregistering devices") we can now move net_set_todo() back. Reviewed-by:
-
Jakub Kicinski authored
Petr Machata says: ==================== nexthop: More fine-grained policies for netlink message validation There is currently one policy that covers all attributes for next hop object management. Actual validation is then done in code, which makes it unobvious which attributes are acceptable when, and indeed that everything is rejected as necessary. In this series, split rtm_nh_policy to several policies that cover various aspects of the next hop object configuration, and instead of open-coding the validation, defer to nlmsg_parse(). This should make extending the next hop code simpler as well, which will be relevant in near future for resilient hashing implementation. This was tested by running tools/testing/selftests/net/fib_nexthops.sh. Additionally iproute2 was tweaked to issue "nexthop list id" as an RTM_GETNEXTHOP dump request, instead of a straight get to test that unexpected attributes are indeed rejected. ==================== Link: https://lore.kernel.org/r/cover.1611156111.git.petrm@nvidia.comSigned-off-by:
-
Petr Machata authored
This policy is currently only used for creation of new next hops and new next hop groups. Rename it accordingly and remove the two attributes that are not valid in that context: NHA_GROUPS and NHA_MASTER. For consistency with other policies, do not mention policy array size in the declarator, and replace NHA_MAX for ARRAY_SIZE as appropriate. Note that with this commit, NHA_MAX and __NHA_MAX are not used anymore. Leave them in purely as a user API. Signed-off-by:
Petr Machata <petrm@nvidia.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
-
Petr Machata authored
This function uses the global nexthop policy, but only accepts four particular attributes. Create a new policy that only includes the four supported attributes, and use it. Convert the loop to a series of ifs. Signed-off-by:
-
Petr Machata authored
This function uses the global nexthop policy only to then bounce all arguments except for NHA_ID. Instead, just create a new policy that only includes the one allowed attribute. Signed-off-by:
-
Dan Carpenter authored
The > comparison is intended to be >= to prevent reading beyond the end of the ps->vlans[] array. It doesn't affect run time though because the ps->vlans[] array has VLAN_N_VID (4096) elements and the vlan->vid cannot be > 4094 because it is checked earlier. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/YAbyb5kBJQlpYCs2@mwandaSigned-off-by:
-
- 20 Jan, 2021 22 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski authored
Conflicts: drivers/net/can/dev.c commit 03f16c50 ("can: dev: can_restart: fix use after free bug") commit 3e77f70e ("can: dev: move driver related infrastructure into separate subdir") Code move. drivers/net/dsa/b53/b53_common.c commit 8e4052c3 ("net: dsa: b53: fix an off by one in checking "vlan->vid"") commit b7a9e0da ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects") Field rename. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Networking fixes for 5.11-rc5, including fixes from bpf, wireless, and can trees. Current release - regressions: - nfc: nci: fix the wrong NCI_CORE_INIT parameters Current release - new code bugs: - bpf: allow empty module BTFs Previous releases - regressions: - bpf: fix signed_{sub,add32}_overflows type handling - tcp: do not mess with cloned skbs in tcp_add_backlog() - bpf: prevent double bpf_prog_put call from bpf_tracing_prog_attach - bpf: don't leak memory in bpf getsockopt when optlen == 0 - tcp: fix potential use-after-free due to double kfree() - mac80211: fix encryption issues with WEP - devlink: use right genl user_ptr when handling port param get/set - ipv6: set multicast flag on the multicast route - tcp: fix TCP_USER_TIMEOUT with zero window Previous releases - always broken: - bpf: local storage helpers should check nullness of owner ptr passed - mac80211: fix incorrect strlen of .write in debugfs - cls_flower: call nla_ok() before nla_next() - skbuff: back tiny skbs with kmalloc() in __netdev_alloc_skb() too" * tag 'net-5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits) net: systemport: free dev before on error path net: usb: cdc_ncm: don't spew notifications net: mscc: ocelot: Fix multicast to the CPU port tcp: Fix potential use-after-free due to double kfree() bpf: Fix signed_{sub,add32}_overflows type handling can: peak_usb: fix use after free bugs can: vxcan: vxcan_xmit: fix use after free bug can: dev: can_restart: fix use after free bug tcp: fix TCP socket rehash stats mis-accounting net: dsa: b53: fix an off by one in checking "vlan->vid" tcp: do not mess with cloned skbs in tcp_add_backlog() selftests: net: fib_tests: remove duplicate log test net: nfc: nci: fix the wrong NCI_CORE_INIT parameters sh_eth: Fix power down vs. is_opened flag ordering net: Disable NETIF_F_HW_TLS_RX when RXCSUM is disabled netfilter: rpfilter: mask ecn bits before fib lookup udp: mask TOS bits in udp_v4_early_demux() xsk: Clear pool even for inactive queues bpf: Fix helper bpf_map_peek_elem_proto pointing to wrong callback sh_eth: Make PHY access aware of Runtime PM to fix reboot crash ... -
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tipLinus Torvalds authored
Pull xen fix from Juergen Gross: "A fix for build failure showing up in some configurations" * tag 'for-linus-5.11-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: x86/xen: fix 'nopvspin' build error
-
Tianjia Zhang authored
On the following call path, `sig->pkey_algo` is not assigned in asymmetric_key_verify_signature(), which causes runtime crash in public_key_verify_signature(). keyctl_pkey_verify asymmetric_key_verify_signature verify_signature public_key_verify_signature This patch simply check this situation and fixes the crash caused by NULL pointer. Fixes: 21552563 ("X.509: support OSCCA SM2-with-SM3 certificate verification") Reported-by:Tobias Markus <tobias@markus-regensburg.de> Signed-off-by:
Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-and-tested-by:
Toke Høiland-Jørgensen <toke@redhat.com> Tested-by:
João Fonseca <jpedrofonseca@ua.pt> Acked-by:
Jarkko Sakkinen <jarkko@kernel.org> Cc: stable@vger.kernel.org # v5.10+ Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Takashi Iwai authored
After the recent actions to convert readpages aops to readahead, the NULL checks of readpages aops in cachefiles_read_or_alloc_page() may hit falsely. More badly, it's an ASSERT() call, and this panics. Drop the superfluous NULL checks for fixing this regression. [DH: Note that cachefiles never actually used readpages, so this check was never actually necessary] BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208883 BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1175245 Fixes: 9ae326a6 ("CacheFiles: A cache that backs onto a mounted filesystem") Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by:
-
Jakub Kicinski authored
Merge tag 'linux-can-fixes-for-5.11-20210120' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== linux-can-fixes-for-5.11-20210120 All three patches are by Vincent Mailhol and fix a potential use after free bug in the CAN device infrastructure, the vxcan driver, and the peak_usk driver. In the TX-path the skb is used to read from after it was passed to the networking stack with netif_rx_ni(). * tag 'linux-can-fixes-for-5.11-20210120' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can: can: peak_usb: fix use after free bugs can: vxcan: vxcan_xmit: fix use after free bug can: dev: can_restart: fix use after free bug ==================== Link: https://lore.kernel.org/r/20210120125202.2187358-1-mkl@pengutronix.deSigned-off-by:
-
Pan Bian authored
On the error path, it should goto the error handling label to free allocated memory rather than directly return. Fixes: 31bc72d9 ("net: systemport: fetch and use clock resources") Signed-off-by:
Pan Bian <bianpan2016@163.com> Acked-by:
-
Grant Grundler authored
RTL8156 sends notifications about every 32ms. Only display/log notifications when something changes. This issue has been reported by others: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472 https://lkml.org/lkml/2020/8/27/1083 ... [785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd [785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00 [785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN [785962.929954] usb 1-1: Manufacturer: Realtek [785962.929956] usb 1-1: SerialNumber: 000000001 [785962.991755] usbcore: registered new interface driver cdc_ether [785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15 [785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384 [785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384 [785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15 [785963.019211] usbcore: registered new interface driver cdc_ncm [785963.023856] usbcore: registered new interface driver cdc_wdm [785963.025461] usbcore: registered new interface driver cdc_mbim [785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0 [785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected [785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected [785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected ... This is about 2KB per second and will overwrite all contents of a 1MB dmesg buffer in under 10 minutes rendering them useless for debugging many kernel problems. This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering the majority of those logs useless too. When the link is up (expected state), spew amount is >2x higher: ... [786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected [786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink [786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected [786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink [786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected [786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink ... Chrome OS cannot support RTL8156 until this is fixed. Signed-off-by:
Grant Grundler <grundler@chromium.org> Reviewed-by:
Hayes Wang <hayeswang@realtek.com> Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.orgSigned-off-by:
-
Alban Bedel authored
Multicast entries in the MAC table use the high bits of the MAC address to encode the ports that should get the packets. But this port mask does not work for the CPU port, to receive these packets on the CPU port the MAC_CPU_COPY flag must be set. Because of this IPv6 was effectively not working because neighbor solicitations were never received. This was not apparent before commit 9403c158 (net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries) as the IPv6 entries were broken so all incoming IPv6 multicast was then treated as unknown and flooded on all ports. To fix this problem rework the ocelot_mact_learn() to set the MAC_CPU_COPY flag when a multicast entry that target the CPU port is added. For this we have to read back the ports endcoded in the pseudo MAC address by the caller. It is not a very nice design but that avoid changing the callers and should make backporting easier. Signed-off-by:
Alban Bedel <alban.bedel@aerq.com> Fixes: 9403c158 ("net: mscc: ocelot: support IPv4, IPv6 and plain Ethernet mdb entries") Link: https://lore.kernel.org/r/20210119140638.203374-1-alban.bedel@aerq.comSigned-off-by:
-
Kuniyuki Iwashima authored
Receiving ACK with a valid SYN cookie, cookie_v4_check() allocates struct request_sock and then can allocate inet_rsk(req)->ireq_opt. After that, tcp_v4_syn_recv_sock() allocates struct sock and copies ireq_opt to inet_sk(sk)->inet_opt. Normally, tcp_v4_syn_recv_sock() inserts the full socket into ehash and sets NULL to ireq_opt. Otherwise, tcp_v4_syn_recv_sock() has to reset inet_opt by NULL and free the full socket. The commit 01770a16 ("tcp: fix race condition when creating child sockets from syncookies") added a new path, in which more than one cores create full sockets for the same SYN cookie. Currently, the core which loses the race frees the full socket without resetting inet_opt, resulting in that both sock_put() and reqsk_put() call kfree() for the same memory: sock_put sk_free __sk_free sk_destruct __sk_destruct sk->sk_destruct/inet_sock_destruct kfree(rcu_dereference_protected(inet->inet_opt, 1)); reqsk_put reqsk_free __reqsk_free req->rsk_ops->destructor/tcp_v4_reqsk_destructor kfree(rcu_dereference_protected(inet_rsk(req)->ireq_opt, 1)); Calling kmalloc() between the double kfree() can lead to use-after-free, so this patch fixes it by setting NULL to inet_opt before sock_put(). As a side note, this kind of issue does not happen for IPv6. This is because tcp_v6_syn_recv_sock() clones both ipv6_opt and pktopts which correspond to ireq_opt in IPv4. Fixes: 01770a16 ("tcp: fix race condition when creating child sockets from syncookies") CC: Ricardo Dias <rdias@singlestore.com> Signed-off-by:
Kuniyuki Iwashima <kuniyu@amazon.co.jp> Reviewed-by:
Benjamin Herrenschmidt <benh@amazon.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20210118055920.82516-1-kuniyu@amazon.co.jpSigned-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf 2021-01-20 1) Fix wrong bpf_map_peek_elem_proto helper callback, from Mircea Cirjaliu. 2) Fix signed_{sub,add32}_overflows type truncation, from Daniel Borkmann. 3) Fix AF_XDP to also clear pools for inactive queues, from Maxim Mikityanskiy. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf: bpf: Fix signed_{sub,add32}_overflows type handling xsk: Clear pool even for inactive queues bpf: Fix helper bpf_map_peek_elem_proto pointing to wrong callback ==================== Link: https://lore.kernel.org/r/20210120163439.8160-1-daniel@iogearbox.netSigned-off-by: -
Daniel Borkmann authored
Fix incorrect signed_{sub,add32}_overflows() input types (and a related buggy comment). It looks like this might have slipped in via copy/paste issue, also given prior to 3f50f132 ("bpf: Verifier, do explicit ALU32 bounds tracking") the signature of signed_sub_overflows() had s64 a and s64 b as its input args whereas now they are truncated to s32. Thus restore proper types. Also, the case of signed_add32_overflows() is not consistent to signed_sub32_overflows(). Both have s32 as inputs, therefore align the former. Fixes: 3f50f132 ("bpf: Verifier, do explicit ALU32 bounds tracking") Reported-by:De4dCr0w <sa516203@mail.ustc.edu.cn> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Reviewed-by:
John Fastabend <john.fastabend@gmail.com> Acked-by:
Alexei Starovoitov <ast@kernel.org>
-
Vincent Mailhol authored
After calling peak_usb_netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the can_frame cf which aliases skb memory is accessed after the peak_usb_netif_rx_ni(). Reordering the lines solves the issue. Fixes: 0a25e1f4 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Link: https://lore.kernel.org/r/20210120114137.200019-4-mailhol.vincent@wanadoo.frSigned-off-by:
Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Vincent Mailhol authored
After calling netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the canfd_frame cfd which aliases skb memory is accessed after the netif_rx_ni(). Fixes: a8f820a3 ("can: add Virtual CAN Tunnel driver (vxcan)") Link: https://lore.kernel.org/r/20210120114137.200019-3-mailhol.vincent@wanadoo.frSigned-off-by:
-
Vincent Mailhol authored
After calling netif_rx_ni(skb), dereferencing skb is unsafe. Especially, the can_frame cf which aliases skb memory is accessed after the netif_rx_ni() in: stats->rx_bytes += cf->len; Reordering the lines solves the issue. Fixes: 39549eef ("can: CAN Network device driver and Netlink interface") Link: https://lore.kernel.org/r/20210120114137.200019-2-mailhol.vincent@wanadoo.frSigned-off-by: -
Yuchung Cheng authored
The previous commit 32efcc06 ("tcp: export count for rehash attempts") would mis-account rehashing SNMP and socket stats: a. During handshake of an active open, only counts the first SYN timeout b. After handshake of passive and active open, stop updating after (roughly) TCP_RETRIES1 recurring RTOs c. After the socket aborts, over count timeout_rehash by 1 This patch fixes this by checking the rehash result from sk_rethink_txhash. Fixes: 32efcc06 ("tcp: export count for rehash attempts") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Link: https://lore.kernel.org/r/20210119192619.1848270-1-ycheng@google.comSigned-off-by:
-
Dan Carpenter authored
The > comparison should be >= to prevent accessing one element beyond the end of the dev->vlans[] array in the caller function, b53_vlan_add(). The "dev->vlans" array is allocated in the b53_switch_init() function and it has "dev->num_vlans" elements. Fixes: a2482d2c ("net: dsa: b53: Plug in VLAN support") Signed-off-by:
-
Jarod Wilson authored
This comes from an end-user request, where they're running multiple VMs on hosts with bonded interfaces connected to some interest switch topologies, where 802.3ad isn't an option. They're currently running a proprietary solution that effectively achieves load-balancing of VMs and bandwidth utilization improvements with a similar form of transmission algorithm. Basically, each VM has it's own vlan, so it always sends its traffic out the same interface, unless that interface fails. Traffic gets split between the interfaces, maintaining a consistent path, with failover still available if an interface goes down. Unlike bond_eth_hash(), this hash function is using the full source MAC address instead of just the last byte, as there are so few components to the hash, and in the no-vlan case, we would be returning just the last byte of the source MAC as the hash value. It's entirely possible to have two NICs in a bond with the same last byte of their MAC, but not the same MAC, so this adjustment should guarantee distinct hashes in all cases. This has been rudimetarily tested to provide similar results to the proprietary solution it is aiming to replace. A patch for iproute2 is also posted, to properly support the new mode there as well. Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Cc: Thomas Davis <tadavis@lbl.gov> Signed-off-by:
Jarod Wilson <jarod@redhat.com> Link: https://lore.kernel.org/r/20210119010927.1191922-1-jarod@redhat.comSigned-off-by:
-
Paolo Abeni authored
The commit dbd50f23 ("net: move the hsize check to the else block in skb_segment") introduced a data corruption for devices supporting scatter-gather. The problem boils down to signed/unsigned comparison given unexpected results: if signed 'hsize' is negative, it will be considered greater than a positive 'len', which is unsigned. This commit addresses resorting to the old checks order, so that 'hsize' never has a negative value when compared with 'len'. v1 -> v2: - reorder hsize checks instead of explicit cast (Alex) Bisected-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Fixes: dbd50f23 ("net: move the hsize check to the else block in skb_segment") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Eric Dumazet authored
Heiner Kallweit reported that some skbs were sent with the following invalid GSO properties : - gso_size > 0 - gso_type == 0 This was triggerring a WARN_ON_ONCE() in rtl8169_tso_csum_v2. Juerg Haefliger was able to reproduce a similar issue using a lan78xx NIC and a workload mixing TCP incoming traffic and forwarded packets. The problem is that tcp_add_backlog() is writing over gso_segs and gso_size even if the incoming packet will not be coalesced to the backlog tail packet. While skb_try_coalesce() would bail out if tail packet is cloned, this overwriting would lead to corruptions of other packets cooked by lan78xx, sharing a common super-packet. The strategy used by lan78xx is to use a big skb, and split it into all received packets using skb_clone() to avoid copies. The drawback of this strategy is that all the small skb share a common struct skb_shared_info. This patch rewrites TCP gso_size/gso_segs handling to only happen on the tail skb, since skb_try_coalesce() made sure it was not cloned. Fixes: 4f693b55 ("tcp: implement coalescing on backlog queue") Signed-off-by:
Juerg Haefliger <juergh@canonical.com> Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=209423 Link: https://lore.kernel.org/r/20210119164900.766957-1-eric.dumazet@gmail.comSigned-off-by:
-
Xu Wang authored
fix semicolon.cocci warnings: ./drivers/net/ethernet/marvell/octeontx2/af/rvu_npc_fs.c:272:2-3: Unneeded semicolon drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.c:1788:3-4: Unneeded semicolon drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.c:1809:3-4: Unneeded semicolon drivers/net/ethernet/marvell/octeontx2/af/rvu.c:1326:2-3: Unneeded semicolon Signed-off-by:
Xu Wang <vulab@iscas.ac.cn> Link: https://lore.kernel.org/r/20210119075059.17493-1-vulab@iscas.ac.cn Link: https://lore.kernel.org/r/20210119075507.17699-1-vulab@iscas.ac.cn Link: https://lore.kernel.org/r/20210119080037.17931-1-vulab@iscas.ac.cnSigned-off-by:
-
Geert Uytterhoeven authored
Currently the smsc911x driver has mininal power management: during driver probe, the device is powered up, and during driver remove, it is powered down. Improve power management by making it more fine-grained: 1. Power the device down when driver probe is finished, 2. Power the device (down) when it is opened (closed), 3. Make sure the device is powered during PHY access. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210118150857.796943-1-geert+renesas@glider.beSigned-off-by:
-
