- 12 Feb, 2021 26 commits
-
-
Hao Chen authored
hclge_rm_vport_all_mac_table() is bloated, so split it into separate functions for readability and maintainability. Signed-off-by:
Hao Chen <chenhao288@hisilicon.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Huazhong Tan authored
To make it more readable and maintainable, split hclgevf_set_rss_tuple() into two parts. Signed-off-by:
-
Huazhong Tan authored
To make it more readable and maintainable, split hclge_set_rss_tuple() into two parts. Signed-off-by:
-
Yufeng Mo authored
hclgevf_cmd_send() is bloated, so split it into separate functions for readability and maintainability. Signed-off-by:
Yufeng Mo <moyufeng@huawei.com> Signed-off-by:
-
Yufeng Mo authored
hclge_cmd_send() is bloated, so split it into separate functions for readability and maintainability. Signed-off-by:
-
Jian Shen authored
hclge_dbg_dump_qos_buf_cfg() is bloated, so split it into separate functions for readability and maintainability. Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
-
Jian Shen authored
To improve code readability and maintainability, separate the flow type parsing part and the converting part from bloated hclgevf_get_rss_tuple(). Signed-off-by:
-
Jian Shen authored
To improve code readability and maintainability, separate the flow type parsing part and the converting part from bloated hclge_get_rss_tuple(). Signed-off-by:
-
Peng Li authored
To improve code readability and maintainability, separate the command handling part and the status parsing part from bloated hclge_set_vf_vlan_common(). Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Jiaran Zhang authored
Use common ipv6_addr_any() to determine if an addr is ipv6 any addr. Signed-off-by:
Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by:
-
Peng Li authored
As more commands are added, hns3_dbg_cmd_write() is going to get more bloated, so move the part about command check into a separate function. Signed-off-by:
-
Peng Li authored
To improve code readability and maintainability, refactor hclgevf_cmd_convert_err_code() with an array of imp_errcode and common_errno mapping, instead of a bloated switch/case. Signed-off-by:
-
Peng Li authored
To improve code readability and maintainability, refactor hclge_cmd_convert_err_code() with an array of imp_errcode and common_errno mapping, instead of a bloated switch/case. Signed-off-by:
-
David S. Miller authored
Tariq Toukan says: ==================== Compile-flag for sock RX queue mapping Socket's RX queue mapping logic is useful also for non-XPS use cases. This series breaks the dependency between the two, introducing a new kernel config flag SOCK_RX_QUEUE_MAPPING. Here we select this new kernel flag from TLS_DEVICE, as well as XPS. ==================== Acked-by:Jakub Kicinski <kuba@kernel.org>
-
Tariq Toukan authored
No real dependency on XPS, but on RX queue mapping, which is being selected by TLS_DEVICE. Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Reviewed-by:
Maxim Mikityanskiy <maximmi@nvidia.com> Signed-off-by:
-
Tariq Toukan authored
Compile-in the socket RX queue mapping field and logic when TLS_DEVICE is enabled. This allows device drivers to pick the recorded socket's RX queue and use it for streams distribution. Signed-off-by:
-
Tariq Toukan authored
Use a new config SOCK_RX_QUEUE_MAPPING to compile-in the socket RX queue field and logic, instead of the XPS config. This breaks dependency in XPS, and allows selecting it from non-XPS use cases, as we do in the next patch. In addition, use the new flag to wrap the logic in sk_rx_queue_get() and protect access to the sk_rx_queue_mapping field, while keeping the function exposed unconditionally, just like sk_rx_queue_set() and sk_rx_queue_clear(). Signed-off-by:
-
Arjun Roy authored
Explicitly define reserved field and require it and any subsequent fields to be zero-valued for now. Additionally, limit the valid CMSG flags that tcp_zerocopy_receive accepts. Fixes: 7eeba170 ("tcp: Add receive timestamp support for receive zerocopy.") Signed-off-by:
Arjun Roy <arjunroy@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Suggested-by:
David Ahern <dsahern@gmail.com> Suggested-by:
Leon Romanovsky <leon@kernel.org> Suggested-by:
-
Heiner Kallweit authored
Cleaning up tx descriptors first increases the chance that rtl_rx() can allocate new skb's from the cache. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Cong Wang authored
dev_ifsioc_locked() is called with only RCU read lock, so when there is a parallel writer changing the mac address, it could get a partially updated mac address, as shown below: Thread 1 Thread 2 // eth_commit_mac_addr_change() memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); // dev_ifsioc_locked() memcpy(ifr->ifr_hwaddr.sa_data, dev->dev_addr,...); Close this race condition by guarding them with a RW semaphore, like netdev_get_name(). We can not use seqlock here as it does not allow blocking. The writers already take RTNL anyway, so this does not affect the slow path. To avoid bothering existing dev_set_mac_address() callers in drivers, introduce a new wrapper just for user-facing callers on ioctl and rtnetlink paths. Note, bonding also changes slave mac addresses but that requires a separate patch due to the complexity of bonding code. Fixes: 3710becf ("net: RCU locking for simple ioctl()") Reported-by:
"Gong, Sishuai" <sishuai@purdue.edu> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Cong Wang <cong.wang@bytedance.com> Signed-off-by:
-
Stefan Chulski authored
The condition should be skipped if CPU ID equal to nthreads. The patch doesn't fix any actual issue since nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS). On all current Armada platforms, the number of CPU's is less than MVPP2_MAX_THREADS. Fixes: e531f767 ("net: mvpp2: handle cases where more CPUs are available than s/w threads") Reported-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Stefan Chulski <stefanc@marvell.com> Reviewed-by:
-
David S. Miller authored
Vignesh Raghavendra says: ==================== net: ti: am65-cpsw-nuss: Add switchdev driver This series adds switchdev support for AM65 CPSW NUSS driver to support multi port CPSW present on J721e and AM64 SoCs. It adds devlink hook to switch b/w switch mode and multi mac mode. v2: Rebased on latest net-next Update patch 1/4 with rationale for using devlink ====================
-
Vignesh Raghavendra authored
J721e, J7200 and AM64 have multi port switches which can work in multi mac mode and in switch mode. Add documentation explaining how to use different modes. Borrowed from: Documentation/networking/device_drivers/ethernet/ti/cpsw_switchdev.rst Signed-off-by:
Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by:
-
Vignesh Raghavendra authored
J721e, J7200 and AM64 have multi port switches which can work in multi mac mode and in switch mode. Add support for configuring this HW in switch mode using devlink and switchdev notifiers. Support is similar to existing CPSW switchdev implementation of TI's 32 bit platform like AM33/AM43/AM57. To enable switch mode: devlink dev param set platform/8000000.ethernet name switch_mode value true cmode runtime All configuration is implemented via switchdev API and notifiers. Supported: - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS - SWITCHDEV_ATTR_ID_PORT_STP_STATE - SWITCHDEV_OBJ_ID_PORT_VLAN - SWITCHDEV_OBJ_ID_PORT_MDB - SWITCHDEV_OBJ_ID_HOST_MDB Hence AM65 CPSW switchdev driver supports: - FDB offloading - MDB offloading - VLAN filtering and offloading - STP Signed-off-by: -
Vignesh Raghavendra authored
Register netdevice notifiers in order to receive notification when individual MAC ports are added to the HW bridge. Signed-off-by:
-
Vignesh Raghavendra authored
AM65 NUSS ethernet switch on K3 devices can be configured to work either in independent mac mode where each port acts as independent network interface (multi mac) or switch mode. Add devlink hooks to provide a way to switch b/w these modes. Rationale to use devlink instead of defaulting to bridge mode is that SoC use cases require to support multiple independent MAC ports with no switching so that users can use software bridges with multi-mac configuration (e.g: to support LAG, HSR/PRP, etc). Also, switching between multi mac and switch mode requires significant Port and ALE reconfiguration, therefore is easier to be made as part of mode change devlink hooks. It also allows to keep user interface similar to what was implemented for the previous generation of TI CPSW IP (on AM33/AM43/AM57 SoCs). Signed-off-by:
-
- 11 Feb, 2021 14 commits
-
-
David S. Miller authored
Rafał Miłecki says: ==================== bcm4908_enet: post-review fixes V2 of my BCM4908 Ethernet patchset was applied to the net-next.git and it was later that is received some extra reviews. I'm sending patches that handle pointed out issues. David: earler I missed that V2 was applied and I sent V3 and V4 of my inital patchset. Sorry for that. I think it's the best to ignore V3 and V4 I sent and proceed with this fixes patchset instead. ==================== Signed-off-by: -
Rafał Miłecki authored
Use le32_to_cpu() for reading __le32 struct field filled by hw. Signed-off-by:
Rafał Miłecki <rafal@milecki.pl> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Use ETH_FCS_LEN instead of magic value and drop incorrect + 2 Signed-off-by:
-
Rafał Miłecki authored
1. Fix "ensable" typo noticed by Andrew 2. Fix chipset name in the struct net_device_ops variable Suggested-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Rafał Miłecki authored
It seems preferred to let compiler optimize code if applicable. While at it drop unused enet_umac_maskset(). Suggested-by:
-
Rafał Miłecki authored
dma_alloc_coherent takes care of zeroing allocated memory Suggested-by:
-
Rafał Miłecki authored
compatible string was updated to match normal naming convention so update driver as well Signed-off-by:
-
Rafał Miłecki authored
It should be /included/ by every Ethernet controller binding. It adds support for various generic properties. Suggested-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Rafał Miłecki authored
Rob pointed out that a normal convention is "brcm,bcm4908-enet" so update whole binding to match it. Suggested-by:
-
git://git.kernel.org/pub/scm/linux/kernDavid S. Miller authored
el/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2021-02-11 Here's the main bluetooth-next pull request for 5.12: - Add support for advertising monitor offliading using Microsoft vendor extensions - Add firmware download support for MediaTek MT7921U USB devices - Suspend-related fixes for Qualcomm devices - Add support for Intel GarfieldPeak controller - Various other smaller fixes & cleanups Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: -
David S. Miller authored
Geetha sowjanya says: ==================== Add Marvell CN10K support The current admin function (AF) driver and the netdev driver supports OcteonTx2 silicon variants. The same OcteonTx2's Resource Virtualization Unit (RVU) is carried forward to the next-gen silicon ie OcteonTx3, with some changes and feature enhancements. This patch set adds support for OcteonTx3 (CN10K) silicon and gets the drivers to the same level as OcteonTx2. No new OcteonTx3 specific features are added. Changes cover below HW level differences - PCIe BAR address changes wrt shared mailbox memory region - Receive buffer freeing to HW - Transmit packet's descriptor submission to HW - Programmable HW interface identifiers (channels) - Increased MTU support - A Serdes MAC block (RPM) configuration v5-v6 Rebased on top of latest net-next branch. v4-v5 Fixed sparse warnings. v3-v4 Fixed compiler warnings. v2-v3 Reposting as a single thread. Rebased on top latest net-next branch. v1-v2 Fixed check-patch reported issues. ==================== Signed-off-by: -
Hariprasad Kelam authored
MAC on CN10K silicon support loopback for selftest or debug purposes. This patch does necessary configuration to loopback packets upon receiving request from LMAC mapped RVU PF's netdev via mailbox. Also MAC (CGX) on OcteonTx2 silicon variants and MAC (RPM) on OcteonTx3 CN10K are different and loopback needs to be configured differently. Upper layer interface between RVU AF and PF netdev is kept same. Based on silicon variant appropriate fn() pointer is called to config the MAC. Signed-off-by:
Hariprasad Kelam <hkelam@marvell.com> Signed-off-by:
Geetha sowjanya <gakula@marvell.com> Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
Hariprasad Kelam authored
RPM supports below list of counters as an extension to existing counters * class based flow control pause frames * vlan/jabber/fragmented packets * fcs/alignment/oversized error packets This patch adds support to display supported RPM counters via debugfs and define new mbox rpm_stats to read all support counters. Signed-off-by:
Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com> Signed-off-by:
-
Rakesh Babu authored
Flow control configuration is different for CGX(Octeontx2) and RPM(CN10K) functional blocks. This patch adds the necessary changes for RPM to support 802.3 pause frames configuration on cn10k platforms. Signed-off-by:
Rakesh Babu <rsaladi2@marvell.com> Signed-off-by:
-
